Search Documents

By E. J. Whittenberger

OVER the past two decades, the Cr-Ni stainless steels, popularly termed 18-8 steels, have been used in ever increasing amounts in the aircraft, automotive, chemical, transportation, and building industries.' The contribution of nickel to these steels is associated with its strong austenite forming tendencies which assure good hot and cold forming characteristics, and with its beneficial influence upon corrosion resistance, especially in oxidizing acids. The adjustment of the chromium and nickel contents has been used advantageously in controlling the rollability and the response of the mechanical properties of these steels to cold reduction. With the advent of the jet age and the government stockpiling of nickel, considerable emphasis has been placed upon the development of satisfactory low nickel or nickel-free substitute austenitic stainless steels, especially for nonmilitary applications.2 Fer-ritic 17 pct Cr (AISI Type 430) stainless steel has been effectively substituted for the austenitic grades in applications with mildly corrosive exposure. However, the limited formability and ferromagnetic behavior of this grade do not permit its satisfactory use for many applications. To achieve better formability in a nenmagnetic steel and conserve nickel, a number of low nickel substitute austenitic grades of stainless steel have been developed in recent years. In most of these steels, manganese and nitrogen have been substituted for a portion of the nickel content, for example, 17 pct Cr-4 pct Ni-6 pct Mn (AISI Type 201), 18 pct Cr-5 pct Ni-8 pct Mn (AISI Type 202), and 16 pct Cr-1 pct Ni-17 pct Mn, all of which contain approximately 0.15 pct N.1 The precipitation of ferrite when large ingots of these Cr-Ni-Mn-N steels are heated to temperatures high enough for conversion to slabs on conventional universal slabbing mills has seriously affected the hot workability of these steels. This has been especially true in the case of the 16 pct Cr-1 pct Ni-17 pct Mn (sometimes referred to as 15 pct Cr-1 pct Ni-15 pct Mn) composition." Because it is possible that little, if any, nickel will be available for nonmilitary stainless steel applications in the event of a national emergency, a need has existed for a nickel-free austenitic stainless steel containing hot and cold forming characteristics similar to 18-8 steels and corrosion resistance at least comparable to the 17 pct Cr ferritic steel. The aforementioned deleterious effect of ferrite upon the hot working characteristics of the 16 pct Cr-1 pct Ni-17 pct Mn, steel indicates the importance of establishing the austenite-austenite plus ferrite phase boundaries as the first step in the development of nickel-free or low nickel substitute steels. This paper presents the data collected in an elevated temperature constitutional study of the Cr-Ni-Mn-N system at the South Works of the United States Steel Corp. Experimental Procedure The 300 compositions used in the investigation were melted in a 26 Ib induction furnace and cast in 3 14 in. diam by 18 in tall hot-tcpped ingot mo1ds.

Jan 1, 1958

By D. L. Katz

The Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July I, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produccs 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand1 indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplifications and generalizations are necessary to give the over-all picture in SO short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, 1, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City Wilcox Secondary Recovery Association on Sept. 5, 1940. Some information is taken from a report to the Association by C. V. Sidwell on March I, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." History of Wilcox Zone The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. I2,3,4 and areal map of Fig. 2. The sand is of Ordovician age and is composed of well assorted, rounded sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 as dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1037 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1942

By D. L. Katz

The Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July I, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produccs 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand1 indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplifications and generalizations are necessary to give the over-all picture in SO short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, 1, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City Wilcox Secondary Recovery Association on Sept. 5, 1940. Some information is taken from a report to the Association by C. V. Sidwell on March I, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." History of Wilcox Zone The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. I2,3,4 and areal map of Fig. 2. The sand is of Ordovician age and is composed of well assorted, rounded sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 as dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1037 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1942

By Ervin E. Underwood

IT has been recognized for many years that dis-persed particles have great value in raising the creep resistance of metallic alloys. In fact, some of the most successful high-temperature alloys owe their superiority to this factor above all others. A recent observation by Glen1," indicates that even better high-temperature resistance to deformation results in alloys capable of two successive precipitation reactions. The ramifications of this finding are of great interest. Unfortunately, our understanding of the reasons for such notable improvements has not kept pace with technical developments. In an effort to uncover some of the basic facts governing strengthening by particles, a program was initiated at the Battelle Memorial Institute with the primary goal of comparing creep strengths in single-phase and two-phase (precipitating) alloys. The effects of precipitation from solid solution on the creep properties of alloys are generally such that the resistance to creep is increased. However, if alloys are heat treated to different degrees of hardness before creep testing, it is often found that those possessing the maximum hardness initially do not necessarily have the maximum creep resistance. Depending on the stresses and temperatures involved other structures may prove more desirable. Considerations of the above nature indicate the importance of defining the initial state of the alloy. Here, it was decided to start with quenched single- phase alloys in which precipitation and creep deformation proceed concurrently. Equipment and Experimental Procedures Preparation of the Specimens—Four 25 lb ingots were prepared from 99.999 pct Cu and 99.996 pct Al to compositions of 1, 2, 3, and 4 wt pct Cu. Spec-trographic and chemical analyses are listed in Table I. After heat treatments and intermediate reductions, the alloys were cold rolled to 1/8 in. thick sheet. The final cold reductions amounted to 50, 40, 20, and 10 pct for the 1, 2, 3, and 4 pct Cu alloys, respectively. The specimens for creep testing were machined into tensile flats 7 in. long, 3/4 in. wide (at the shoulders), and 1/8 in. thick. The reduced sections were 1/4 in. wide and 21/2 in. long. After heat treatments at 540°C to an ASTM grain size of 1 1, the specimens were quenched into water at room temperature, then electropolished in a glacial acetic acid and perchloric acid solution. The gage marks were Knoop impressions placed 2 in. apart on the reduced sections. Blanks of 1 x 1 in, were cut from the same sheets for the age hardening runs and were given the same grain size heat treatments. The specimens and blanks were stored in a refrigerator at —40°C until needed for testing. Creep Measurements—Creep tests were conducted in a constant temperature room which was maintained at 26° ±1°C. A split-type, hinged, vertical-tube furnace was mounted on a horizontal track so that the specimen could be enclosed suddenly. Thus, it took about 15 min for the specimen to come within 5°C of the test temperature. The temperature variation along the specimen was controlled to about

Jan 1, 1958

By L. Bombardieri, H. F. Mills

IRON KING mine, producing gold-silver-lead-zinc ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pattern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length. with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth. the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 51/2 -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material To secure a cheap source of waste fill for stoping operations, a block cave area was undercut In the hanging wall near the north end of the mine above the 600 level. Waste from the block cave is drawn from any of three large drawpoints on the 600 level, and a series of hanging wall transfer raises with controls and bypasses on each level provide a fast low-cost material for fill. The block cave is worked vertically through to surface in the form of a steep-sided hole 350x250 ft and several hundred feet deep, the sides of which cave and provide fill material without any blasting. Fill is a mixture of caliche-cemented surface gravel and small particles of hanging wall schist. Level Development: An orebody 300 times as long as it is wide requires a lot of development work. Former practice consisted of driving a haulage drift about 30 ft from the ore in an andesitic footwall, a drift on the ore, and crosscuts from the haulage drift at 100-ft intervals. Crosscuts are about 90 ft long. At present, only the odd numbered levels are so developed, and on the even numbered levels only the haulage drift and crosscuts are driven. Little or no timber is used for this development. This change resulted in 20 pct reduction of development costs and 50 pet reduction of square set stoping required for removal of floor pillars. Elimination of ore drifts on alternate levels leaves

Jan 1, 1957

By H. E. Montgomery

Engineering trends for some years have been toward higher temperatures, both in process work and in steam generation. Progress in design has been dependent upon the development and evaluation of suitable alloys. Elementary knowledge of the limitations of copper-base alloys indicate their unsuitability for the higher ranges of operating temperatures; say, for steam to 950°F. Emphasis upon the more severe conditions perhaps is a reason why more complete evaluations have not been made for copper-base alloys over their range of suitability. However, the few studies made show clearly the need for more accurate evaluations. Some copper-base alloys long looked upon favorably because of superior room-temperature properties are not as desirable as some others perhaps not so "strong" and "hard," as measured by usual acceptance tests. Load-carrying capacity and structural stability arc two important factors. Structural stability as influenced by temperature, by presence of corrosive media, or by the effects of stress itself, frequently is a limiting factor. An early reference to creep properties of the cast copper-base alloys is that of Brown1 (Admiralty gun metal, Cu 87.5, Sn 10.1, Zn 2.3 and Pb 0.08). His tests were similar to present-day stress-rupture tests without measurement of creep elongrttion. Loading was in steps with usually 24 hr. between steps, and continued until failure. He advocated a "useful strength value" of 61/2 tons (I4,560 Ib.) per sq. in. at 572°F. (300°C.). A specimen broken in 1/2 hr. at 572°F. had a strength of 21 tons (26,880 Ib.) per sq. in. The strength values as determined by 1/2-hr. tests and those by the longer stress-rupturc start to differentiate at 392°F. (200°C). This is the temperature at which time at load began to play an important part. Bolton, Price and Hebemann2 give creep curves on 88-10-2 (A.S.T.M. B-60, CU 88, Sn 10, Zn 2) and steam or valve bronze (A.S.T.M. B-6I, Cu 87.50, Sn 6.00, Zn 3.75, Pb 1.70) at 500°F. Direct comparison of the two alloys under 7500 lb. per sq. in. stress showed the steam bronze (A.S.T.M. B-61) superior in creep strength to the 88-10-2 (A.S.T.M. B-60). The steam bronze shows no creep after 700 hr. (1540-hr. test). The 88-10-2 shows a rate of about 7.0 per cent in 100,000 hr. over the last 700 hr. of the test. Creep curves on the steam bronze are also given at the same temperature (500°F.) with loads of 6500 lb. per sq. in. and 8000 lb. per sq. in. These indicate "creep strengths" (creep rate within I per cent in 100,000 hr.) in excess of 8000 lb. per sq, in. for this alloy. It was found that higher percentages of tin are detrimental to creep resistance. This is caused by the presence of or formation during test of considerable alpha-delta eutectoid in the higher tin alloys. Bolton also states that the high

Jan 1, 1945

By E. L. Kinsella, F. S. White

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,' showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.' Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By F. S. White, E. L. Kinsella

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,' showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.' Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By John M. Kelly

New Mexico produced 39,475,388 bbl. of oil in 1944, the greatest amount in one year in the oil history of the state. This production was 593,046 bbl. or 1.25 per cent more than in 1943. New Mexico retained its position as the seventh largest oil-producing state. The maximum per well allowable on Jan. I, 1944 was 48 bbl. daily and at the end of the year it was 45 bbl. daily. Allocations as set by the New Mexico Oil Conservation Commission closely followed the recommendations made by the' Petroleum Administrator for War. The average daily pipe-line runs were within 4 per cent of the allocation. Production by counties was as fol1ows;Lea County, 33,509,548 bbl.; Eddy County, 5,504,498; Northwestern New Mexico 461, 342. Drilling activity for New Mexico in 1944 was well above that of 1943, with 362 completions. Of these, 283 were oil wells, 12 gas wells and 67 dry holes. The ratio of dry holes to producers, about I to 4, was an improvement over 1943. Wildcat drilling during 1944 was responsible for the discovery of six new fields and the extension of two present producing areas. Drilling records were established in New Mexico during 1944 with the deepest producer ever completed, the Humble Leonard Oil Company's No. I at 11,969 ft., in the Ellenburger section of Ordovician age near Jal, Lea County. The discoveries in Lea County during 1944 were as follows: West Lovington field, where Fred Turner, Jr. drilled his No. I State B .in C SE SW sec. 4-17-36 and completed it for 122 bbl. of oil in 8 1/2 hr., in the San Andreas section of Permian age. The Tonto field, where the T-exas Company completed its No. I Baskin at a total depth of 3586 ft. in Seven Rivers lime of Permian age, with an initial production of 254 bbl. of oil in 21 hours. The Drinkard area, where the Gulf Oil Corporation's Drinkard No. I flowed 782 bbl. of oil in 14 hr. from the Yeso section of lower Permian age, thus opening the first lower Permian production in the state. The total depth of this discovery was 6508 ft. and oil was 38.8" A.P.I. gravity. The Dublin area, where the Humble Oil and Refining Co. established a drilling depth record of 11,969 ft. drilling and completing its No. I Leonard Oil Co. well in the Ellenburger lime of Ordovician age. This well flowed 221 bbl. of oil per day, of 48.9º A.P.I. gravity oil. It is in sec. 12-26-37. The new pay horizon discovery of the Continental Oil Co. in the Skaggs area, where the company completed its Skaggs B-23 No. 2 in sec. 23-20-37 for 236 bbl. of oil in 21 hr. from the Wolfcamp section of lower Permian age, at a total depth of 7725 ft. This well was drilled to granite at 10,465 ft. and plugged back to the Wolf-camp for a new pay zone completion.

Jan 1, 1945

By H. C. Jennison

Two distinct types of defects occur at times in copper wire as a result of the use of dies of improper design or undesirable wire-drawing practice. The conditions under which these defects may be produced, as well as precautions to be taken in order to prevent them, have been known to The American Brass Co. for many years. The quality of the copper wire bars and rods has too often and unjustly been held responsible for these particular defects and it is to correct any such belief that this paper is presented. An extremely high quality of electrolytic copper has been supplied to the trade by all refineries for the last 20 years at least. The purity of the copper would average well above 99.900 per cent. The casting of the wire bars has been handled in a generally satisfactory manner. The bars have been cast sound, with a flat to slightly crowning set and have been free from sloppy edges, cold sets, etc. In other words, the wire bars have met A. S. T. M. specifications and have been generally satisfactory. For the most part, they have been everything that could be desired from a quality standpoint yet most of the wire mills in this country and in Europe have at times held the quality of the copper responsible for the two types of defects described in this paper. As a matter of fact, these defects are produced entirely in the wire mills. The author has visited many of the large wire mills in the United States and in Europe to investigate these defects. In some cases the trouble has been so serious that the wire mill has ceased operations. At times the wire mills are reluctant to believe that they are responsible for the defective product. The effect of die design, wire-drawing practice, etc., upon the quality of copper wire has received little study on the part of wire mills, particularly those that have commenced operations in the last few years. Two Types of Defects One type of defect is generally known in this country as "check marks;" in Europe it is termed "crowfeet" (Fig. 1). This defect occurs in the surface of the copper wire, in the form of V's, which are always

Jan 1, 1930

W. L. SaundeRs, New York City (communication to the Secretary*):—Notwithstanding the sweeping statements made by Mr. Clarke in this paper, the friends of compressed air are not dismayed. There is no war between electricity and compressed air. Each one has its field of usefulness, and in that field each is supreme. In spite of commercial interests, in spite of prejudices and the enthusiasm of the inventor, the thing that is best will survive and flourish. At least ten years ago, our engineering papers contained large advertisements and pages of reading-matter about the application of electricity to mines, recording the introduction of numerous rock-drilling plants, and claiming that the problem had been solved, greatly to the advantage of the miner and with promise of large profits to the manufacturers of electrical apparatus. Edison and Thomson labored to apply electricity to mines, and each believed that the probabilities of success were great. This was the period of the solelloid rock-drill, which mas admirably suited, theoretically, to the percussive principle and in the development of which hundreds of thousands of dollars have been spent without satisfactory result. I have searched in vain for a standard mining equipment where electric rock-drills are in constant, commercial operation. During a recent trip made from New York to California, I visited most of the important mines of the West and failed to discover a single electric equipment, so far as this class of mining-work is concerned. If any one will inform me where there exists today an electric-drilling equipment in constant service in mines in the United States, I shall be glad to receive the information. Mr. Clarke has been for some years an active and intelligent writer on the subject of electricity for mining. Whenever his

Jan 1, 1904

By David R. Mitchell

Many of the difficult operating problems of the preparation of coal for market, of sampling coal shipments and in the utilization of coal are caused by segregation in the coal mass. Segregation may be of two kinds: i.e., "size segregation," in which particles of the same size in a mass of coal containing a range of sizes collect together and "density segregation," in which particles of the same density or specific gravity in a mass of particles of varying density gather together. Mechanics of Segregation Size segregation cannot take place with closely sized coal. As the size range increases, the tendency for size segregation increases. Similarly, cleaned coal with particles of approximately the same specific gravity have very little tendency for density segregation. The wider the density range of particles and the more particles of different density, the greater the chances are for density segregation. The following discussion deals primarily with coal of a wide size range as screenings and of wide density differences as uncleaned or run-of-mine screenings. If a mass of coal containing particles of a wide size range is subject to the stream action of a moving current of water, the small particles are transported farther than the coarser. Particles of different density in a stream of moving water are subject to the laws of classification, the heavier settling out first. The familiar sluice box of the gold miner and the action of rivers and other streams in classifying material according to

Jan 1, 1938

By David R. Mitchell

Many of the difficult operating problems of the preparation of coal for market, of sampling coal shipments and in the utilization of coal are caused by segregation in the coal mass. Segregation may be of two kinds: i.e., "size segregation," in which particles of the same size in a mass of coal containing a range of sizes collect together and "density segregation," in which particles of the same density or specific gravity in a mass of particles of varying density gather together. Mechanics of Segregation Size segregation cannot take place with closely sized coal. As the size range increases, the tendency for size segregation increases. Similarly, cleaned coal with particles of approximately the same specific gravity have very little tendency for density segregation. The wider the density range of particles and the more particles of different density, the greater the chances are for density segregation. The following discussion deals primarily with coal of a wide size range as screenings and of wide density differences as uncleaned or run-of-mine screenings. If a mass of coal containing particles of a wide size range is subject to the stream action of a moving current of water, the small particles are transported farther than the coarser. Particles of different density in a stream of moving water are subject to the laws of classification, the heavier settling out first. The familiar sluice box of the gold miner and the action of rivers and other streams in classifying material according to

Jan 1, 1938

By A. J. Stosick, J. R. Hoffman, E. Rudy, St. Windisch

The binary alloy system Mo-C zoas investigated by means of X-ray, metallog/aphic, thermoanalytical, and melting-point techniques on chemically analyzed specimens. The system, Fig. 39, is characterized by three congruently melting, intermediate phases, Mo2C, n MoCi-x, and aMoC1-,, of which only Mo,C is stable at temperatures below 1650°C. Substoichio-metrzc (~32.5 at. pct C) dimolybdenum carbide undergoes a homogeneous sublattice order-disorder transformation at temperatures of approximately 1400°C, whereas hyperstoichiorrletric compositions undergo a discontinuous Phase change. The order-disorder transitions in the Me, C phases are discussed in terms of the structural changes involved in the transformation processes and the absence of long-range sublattice coherency in stoichiometric or hyperstoiclziomet-ric compositions attributed to the impossibility of obtaining long-range order in a linear chain of alternating carbon atoms and vacancies. From the experimental phase relutionships and the known thermody-namic data for Mo2 C, limits for the free energies of formation for the high-temperature phases r) MoC1-, and aMoC1-, are deriued and found to be in good agreement with data previously obtained from phase equilibria in ternary metal-carbon systems. IN the course of studies of the high-temperature phase relationships in ternary systems of refractory transition metals with carbon,' a number of inconsistencies found in previous work necessitated a reex-amination of some of the related metal-carbon binaries. A reassessment of the binary system data also seemed

Jan 1, 1968

By G. L. Fisher, R. Maddin

The rate of self-diffusion in silver single crystals during torsional strain was measured over a wide range of tenperatures and strain rates. The torsional strain was applied in a cyclic manner by reversing the divection of twist aftev a certain fraction of the total strain was reached. Surface roughening was substantially reduced in cyclically strained specimens compared with those strained entirely in one direction. Diffusion coefficients were determined using a special sectioning technique whereby slices could be removed parallel to the surface of a strained torsion specimen. The accuracy of the technique was first determined using roughened specinzens statically diffused to various penetration depths. Simultaneous strain-diffusion experiments were then performed over the temperature range 550' to 800 using strain rates of lo-' to 2.2 x 10' sec-'. The increase in silver self-diffusivity during torsional plastic strain was small. In only one case was the enhancement greater than twice the static value of the diffusion coefficzent. The enhancements increased slightly with decreasing tenzperature and increased with increasing strain rate. A dislocation pipe mechanism of enhancement was found to explain the present results satisfactorily. The magnitude of the enhancements and the tenzperatures at which they were observed suggests that a steady-state dislocation density of 10' to 109 dislocations cm-2 existed during the high-tempevature deformation. The diffusion coefficient in an fcc metal can be increased by 1) an excess concentration of point defects and 2) the rapid movement of diffusing atoms along grain boundaries and dislocations. Plastic deformation may be responsible for enhancements by both of these mechanisms. The results of simultaneous strain-diffusion experiments have caused a controversy over the magnitude of the effect of strain upon diffusion. Experiments reporting large enhancements have been criticized for the manner in which the diffusion coefficient was measured. Several of these experiments have been contradicted by other results obtained in a similar manner. No enhancement was reported by two investigators''' who performed their experiments at high temperatures where strain is expected to have little effect upon diffusion. A recent theoretical analysis3 indicates that strain enhancement by a vacancy mechanism will be small and exist only at low temperatures and rapid strain rates. It is doubtful whether any experiment has yet proven that strain enhancements can occur by an excess vacancy mechanism. In the present research, experiments were performed at extremes of temperature and strain rate in an attempt to measure enhancement of diffusion by strain. Self-diffusion of silver during torsional deformation was chosen since two separate investigations4j5 indicate that at least a small enhancement exists under these conditions. An accurate method of determining the diffusion coefficient, mechanical sectioning, was employed after a technique was devised to apply it to the roughened surface of a strained torsion specimen. First, the accuracy of the technique was determined for different penetrations (2fi). Then diffusion experiments were performed at temperatures between 550" and 800°C at strain rates of 10"" to 10"" per sec. I) EXPERIMENTAL PROCEDURE Preparation of Specimens. The experimental procedure detailing the growth of crystals, their treatment, and the annealing techniques during straining are contained in earlier publications.496 The dimensions and orientations of the torsion specimens are shown in Figs. 1 and 2. licatiin of Torsional Strain. The torsion procedure was changed from that used previously. The specimens were strained in cycles to reduce the gross distortion and surface roughening inherent in twisting to high strains in one direction. For all strains above 0.30, the total surface strain was obtained as follows: the specimen was twisted to 0.10 strain in a clockwise direction; the direction was reversed; the backlash in the torsion apparatus was taken up; and the specimen was twisted in a counterclockwise direction through the initial starting point to 0.20 surface shear strain in the opposite direction. The strain reversal took no more than 1 min to accomplish. The total accumulated surface shear strain was arbitrarily taken as the sum of the 0.10 strain in the clockwise direction plus 0.20 in the counterclockwise direction. Although cyclic torsional strain was beneficial, surface roughening and specimen distortion were not entirely eliminated. The variation in the diameter at various points on the specimen was often much greater than the depth of the diffusion zone. Since serious errors might result if specimens were sectioned in the usual manner, a technique of lathe sectioning was devised to allow sections to be taken parallel to planes of equal concentration.

Jan 1, 1967

By Wilbur S. Burbank, Robert G. Leudke

The impressive western San Juan Mountains of Colorado were carved by Pleistocene and Recent erosion from a thick blanket of Tertiary volcanic rocks that rests upon a basement of metamorphic, sedimentary, and igneous rocks ranging in age from Precambrian to Tertiary. These rocks record a long, complex, and fairly complete sequence of geologic events that have affected the region through much of geologic time. The geologic history of the region includes several periods of deformation, erosion, and igneous activity; closely associated with two of these periods were two periods of mineralization. The older of these was related to Late Cretaceous-early Tertiary (Laramide) intrusive activity, and its deposits occur in the older sedimentary units. The younger, of later Tertiary age and related to the widespread middle Tertiary extrusive and intrusive activity, is the chief concern of this paper. Tertiary volcanism built a great plateau surrounding the San Juan volcanic depression, a complex of subsided crustal blocks in the vent areas. The Silverton and Lake City cauldrons, nested within the larger depression, were domed by resurgent magma that created keystone grabens along the distended crests of the domed floors and many postcauldron radial and concentric fractures, dikes, and intrusive plutons within and marginal to the cauldron sites. The postvolcanic evolution of large quantities of gases, chiefly carbon dioxide and water, propylitically altered the rocks in and around the volcanic depression prior to the younger period of ore deposition. The ore deposits, localized mainly in the radial and concentric fractures about the cauldrons and in the associated graben faults, include fissure veins, chimneys, replacements, and disseminations in volcanic and underlying basement rocks. Fissure veins, constituting the major economic source, yielded precious- and basemetal ores. Most veins are compound with sphalerite, galena, and chalcopyrite; some veins contain silver-bearing arsenical sulfosalts and free gold. These minerals occur in predominantly quartz gangue. However, gangues composed of several manganese silicates and carbonates and relatively· barren of metals are abundant locally and probably originated by alteration of rocks at roots of faults and fissures during evolution of carbonatic solutions. The bulk of the ores are hypogene and probably had their source in deep parent magmas of the shallow eruptive rocks. Total production since the early 1870's has exceeded half a billion dollars in recovered metals, with a ratio of precious- to base-metal values of about 3 to 2. Since 1930, improvements in metallurgical treatment and mining techniques have increased the base-metal yield.

Jan 1, 1968

By Charles W. Bloomquist

The profitability of miscible flooding in a hypothetical target oilfield is examined. The major costs, including Windfall Prof it Tax, are identified and their re1ative importance are discussed. The sensitivity of profit to important physical and economic variables is evaluated and discussed, including variance in oil recovery, oil price, injectant requirements, injectant cost, and capital requirements. Economic sensitivities to important development and operating decisions such as timing, Spacing, Slug size, and gas recycling are also analyzed. The Windfall Profit Tax (WPT) as it applies to gas miscible EOR projects is reviewed. The effect of WPT on each of the various project cases is analyzed and the effect of reduced WPT on remaining production from existing operations is evaluated. Tax implications are compared for integrated vs. "independent" controlled projects and the alternative of expensing vs. capitalizing tertiary injectants is also evaluated. The impact of the Net Income Limitation in reducing WPT. during early and late project life is determined and discussed.

Jan 1, 1982

By F. G. ROCKWELL

ALTHOUGH the diamond as a gem stone dates back many hundreds of years its use industrially, at least to any extend is recent. The old adage: "Use a diamond to cut a diamond" indicates that some industrial use was made of this material in cutting and polishing many years ago. It also put to various other industrial by the Romans. General industrial use however was never developed to any considerable extent until about the time of the first World War. It is definiely known however, that a Swiss watchmaker, M. Leschot by name, invented a diamond drill in or about the year 1862, Today, some 75 or 80 per cent of the total didamods produced are used in industry. There are two main classifications of diamonds : (1) carbonados or "black diamonmds," and (2) diamonds proper.

Jan 1, 1944

By Robert H. Richards

Tuns truly remarkable machine was built on a preliminary scale in May, 1895. The first full-sized table was built by Mr. A. R. Wilfley, and was used in his own mill in Kokomo in May, 1896. The first table sold for installation was placed' in the Puzzle mill, Breckinridge county, in August, 1896. The mill enthusiasts at first hailed it as the cure for all the ills that flesh is heir to in the milling line. A little later it was found to make losses which were serious, and on this account the table succeeded only to a limited extent in displacing the vanners of the gold-mills. Still later, mill-men in a number of districts throughout the country made special studies of the faults of the machine, and devised a number of ways of grouping supplementary machines to overcome as far as possible the losses, and at the same time retain the benefit of the extraordinarily large capacity accompanied by the production of clean concentrates for which the machine has become so justly famous. I hope to make an exhibit of some of these methods in an appendix to my book on ore-dressing which is now in preparation. These experimenters have not written up the subject, and if they possess all the facts they have not given them out for the benefit of the mining profession at large. The object of this paper is to obtain the facts and to pre¬sent them so clearly that their bearing can be seen by all. To this end two complete series-'of tests have been planned. One (the present paper), to study concentration of galena in presence of quartz; the other (to follow shortly), to study concentration of chalcopyrite in presence of quartz. Some authorities claim that the table does its best work when treating natural products; by this phrase I mean products which have been crushed to pass through a limiting

Jul 1, 1907

By Robert S. Young

During the last quarter-century, exploration for metallic deposits in Maine has been sporadic with peaks generally coinciding with periods of high metal prices. Known cases of regional or semi-regional evaluations are few; most efforts have been local and usually intensive. On the basis of broad geologic groups, the State has been divided into five fundamental environments: ( 1) coastal metamorphic belt; (2) southern volcanic belt; (3) Silurian slate belt; ( 4) northern volcanic belt; and ( 5) Devonian slate belt. Although not restricted to these areas, exploration in recent years has been concentrated in the northern and southern volcanic belts. Notable examples of recent exploration activity, directed to sulfide minerals, include: ( 1) the Knox County nickel-copper-bearing ultramafic rocks; (2) the Harborside (Cape Rosier) copper-zinc deposit; (3) the Second Pond (Black Hawk) zinc-copper-lead-silver deposit; ( 4) the Big Hill-Barrett lead-zincsilver- copper-gold zones; (5) the Parmachenee copper-zinc belt; ( 6) the Moxie Lake nickeliferous peridotite; and (7) the Attean quartzmonzonite molybdenum-copper occurrences. The Second Pond and Harborside prospects appear to be close to production. Systematic investigations for non-metallic deposits appear to have been aimed principally toward limestone, asbestos, diatomaceous earth, and spodumene-bearing pegmatites. Advances in prospecting methods, high metal prices, a favorable business outlook, increasing cooperation from large landholders, and some discoveries support the probability of increased exploration activity in Maine during the coming decade.

Jan 1, 1968