Search Documents

By Carolina Gomes Dias Ribeiro

The modern composite materials, especially those reinforced with synthetic fibers such as glass and carbon, have been used since last century to attend the demands required by most technological fields, from home appliances to aerospace. Natural fibers composites with biodegradable polymer matrices are considered environmentally friendly materials and currently accepted as possible substitutes for synthetic composites. These green composites can be safely discarded or composted at the end of their life without harm to the environment. Another alternative for synthetic composites is to apply natural lignocellulosic fibers as reinforcement of conventional polymer matrices and already used in the automobile industry. In addition to the environmental and societal advantages of the green composites, the lignocellulosic fiber reinforced conventional polymer composite also has economical and technical advantages. In the case of a fiber collected as a waste, the price of the composite can be considerably lower than “fiberglass”. Furthermore, with high strength lignocellulosic fibers such as sisal, ramie and malva the specific strength of a composite may approach that of “fiberglass”. Therefore the objective of the present work is to investigate the mechanical behavior of polymer matrix composites reinforced with high volumes of natural malva fibers subjected to tensile stresses.

Aug 16, 2017

By José Fagundes Jr., Juliano Braz Possatti, Bruno Câmara Vieira, Gabriel Godinho Alves, Bruno Bastos da Silva Murad, Cristina Maria de Oliveira Roque

Driven by market trends, increasing environmental accountability, government regulations and fostered by the Company’s strategic plan, ArcelorMittal Tubarão has developed new steel products to deliver better solutions to fit each customer’s needs. This often translates in higher strength, more complex and dimensionally challenging (thinner and wider) steels to attend a broad array of goals, such as reduction of vehicles fuel consumption and carbon emissions, increase in fatigue performance of heat treated parts, higher load capacity per net weight in vessels or wagons and lower supplying lead time as ArcelorMittal Tubarão establishes itself as a domestic option for so far imported grades. Based on the annual Product Development Plan, a structured workflow involves technical discussions from an operational point of view about safety issues, metallurgical project, steel grade family definitions, offline simulations prior to field trials, deformation resistance and process parameters adjustments and scheduling strategy. As a result of the increasing synergy between the areas, the share of new materials developed in recent years has been sustainably increased up to 15% in 2018, adding value to the final product without impact on hot rolled coil output and with a low cobble index.

Oct 1, 2019

By Piotr Kula

Vacuum carburising with pre-nitriding (PreNitLPC® technology) involves feeding ammonia during the charge heating stage before carburising. The purpose is to restrict the growth of grain in the surface layer of the carburised steel. The article presents the influence of nitrogen on restricting austenite grain growth during vacuum carburising and on mechanical properties (fatigue strength, impact resistance) of layers that underwent such treatment in comparison with traditional carburising methods.

Aug 16, 2017

By Edgard de Macedo Silva

Aços inoxidáveis duplex apresentam boas propriedades mecânicas e de resistência à corrosão, mas quando são colocados para trabalhar em altas temperaturas como no processo de soldagem e de tratamento térmico ocorre o surgimento de fases que comprometem as suas propriedades. Dentre elas, a fase sigma (s) é a que apresenta um maior efeito de fragilização por ser rica em cromo e empobrecer a matriz desse elemento, bem como por apresentar dureza em torno de 1000HV. No presente trabalho, uma metodologia não destrutiva, baseada na interação entre densidade de linhas de campo e um aço inoxidável duplex, é apresentada para o acompanhamento da formação da fase s na temperatura de 800°C em um aço envelhecido por até 2 horas. Diferentes intensidades de campo foram geradas por um eletroímã e o fluxo de linhas de campo foi aplicado no material de estudo. A densidade de linhas de campo resultante foi medida por um sensor de efeito Hall. Os resultados foram correlacionados com resultados de microscopia eletrônica de varredura (MEV), dureza e difração de raios-X (DRX) e mostraram que os valores de tensão hall reduziram à medida que a fração volumétrica da fase s aumentou. A formação dessa fase não magnética influenciou no sinal obtido pelo sensor Hall. Existiu uma correlação entre a densidade de linhas de campo resultante e a presença da fase fragilizante, apontando para uma metodologia capaz de acompanhar a formação dessa fase.

Aug 8, 2018

By J. N. Stevens, M. Tulwin, P. J. Lawlor

All metals producers are on an unending search for a competitive advantage. They need to produce in the most cost effective way. Sometimes a new mill might be considered but in this paper we present examples of how this might not always be necessary. A detailed investigation by an equipment vendor who can consider the mill and or plant as a complete entity: mechanics, automation and process control can often find solutions that are both lower cost and can be implemented in shorter time frames.

Oct 1, 2019

By Nathanael Wagner Sales Morais

Os aços maraging tem grande importância tecnológica devido sua aplicação nas industrias aeroespacial e nuclear. Uma das aplicações para esse material é a fabricação de cilindros de alta resistência pelo processo de estampagem profunda, logo o conhecimento da textura cristalográfica torna-se fundamental. Este trabalho investigou o efeito da laminação à frio seguida por um recozimento sobre a microestrutura, textura e anisotropia plástica no aço maraging 350. A anisotropia foi medida pelo cálculo dos coeficientes de Lankford e dos coeficientes de anisotropia normal (Rm) e planar (?R). Os resultados mostraram o aumento na deformação a frio gera um aumento na intensidade da fibra acompanhada de um aumento no valor de Rm. As análises metalográficas mostram que maiores reduções induzem à um precipitação intermetálica após o recozimento.

Aug 8, 2018

By Delio Amorim

Industry 4.0 concepts is the new biggest challenge on the industry nowadays and every company in every industry in every part of the globe is looking to implement this somehow on their factories and machines. To do that on the newest long rolling mills, that brings already onboard state-of-the-art technologies, is for sure a challenge of machinery builder industry, but how to become the long rolling mills built on 70’s, 80’s or 90’s part of this innovation process and connected to the new trends? This is the main mission here, to show some examples of applications that goes in this direction.

Oct 1, 2019

By Karl Berger, Michael Steinkogler

The evolution in Metal Cutting: Inventors around the world have been successfully developing innovations for decades, but only some of these developments have had „GAME CHANGING“ potential. One of these innovations is the new developed saw blade LINCUT®, a patented changing system that paves the way for a fundamental reorientation of the entire saw blade industry worldwide through a simple and economical concept for rolling mills or heavy forging lines. Cost efficiency starts with the raw material: Circular saws equipped with a standard saw blade are expected to have a necessary 2 percent standstill per year due to required tool changing. The applied technology reduces this unnecessary loss of production by more than 50%. The ROI can therefore be reached faster which immediately lowers your production costs. No matter what material, conventional carbon steel or highly alloyed stainless steel, the coating and shape of carbide plates is perfected for extended tool life up to 25% with increased performance. Due to LINSINGERs own tool-technology-centre in Austria specialized in research and development of tools, constantly expanding R&D activities, best results are achieved in quality and cost efficiency: a (r)evolution in metal cutting.

Oct 1, 2019

By Lorenzo Bacchetti

Automatic yards with ad-hoc WMS (Warehouse management software), are the key for a modern and efficient warehousing which can face today logistic challenges. WMS boosts the traceability of material while optimizing the storage space. The operations in the yard are safer and logically organized according to algorithms that are specifically adjusted case by case. WMS can easily handle multi-cranes yard avoiding conflicts and increasing accuracy of positioning with decreased number of movements. The synergy of automatic cranes and WMS reduces bottlenecks and speeds up the preparation of deliveries with an overall improvement of warehousing and shipping scheduling.

Oct 1, 2019

By Andrea Pezza

The steel market is experiencing a difficult conjuncture: on the one hand steel producers minimize their investments while optimizing their over- production, on the other hand suppliers reduce their internal human resources and capacity in order to overcome the instability of the new era. A return to the steel production levels of the past is not expected in the short term. Research, development and plant concept optimization is one recipe to drive the future of the steel business. This article describes a new concept for a VOD plant developed as a result of thorough investigation and assessment of all possible solutions. A joint and tight cooperation with the final customer was necessary to reaching important results. This article consists of the contributions from the plant suppliers in terms of their experience and feedback, as well as the final user’s. The final customer, voestalpine Giesserei Linz GmbH, and the plant supplier, Primetals Technologies, are both worldwide players and highly focused on reaching best quality and innovation.

Oct 30, 2017

By Patrícia Mundim Campos Faria

The process of particle size reduction by grinding is inherently inefficient and involves high capital and operating costs. In particular, ball milling is one of the important unit operations in the iron ore pelletizing process. The mill product, due to its physical properties, determines the efficiency of subsequent stages of classification, filtration and pelletizing, thus impacting the quality of iron ore pellets. The work demonstrates the application of the population balance model in the optimization of a full-scale ball mil circuit grinding pellet fines with the aim to evaluate the optimal solids concentration to improve iron ore pellet quality. Initially, detailed experimentation was carried out in a 25.4 cm diameter batch mill and a relationship for mill scale-up using a linear population balance model in wet grinding systems was established. The selection and breakage parameters and the specific selection functions were determined for pellet feed iron ore. It was possible to identify the non-normalizable nature of the breakage functions of the ore studied, which were modeled properly. Afterwards, as a result of incorporating the specific selection functions and breakage functions into the linear population balance model, it was possible to predict product size distributions in the pilot and plant scale mills (0.416 and 5.18 m diameter, respectively) from data obtained in the 25.4 cm diameter mill. Finally, with this scale-up procedure it was possible to appraise the plant scale optimization via laboratory scale grinding mill tests. The effects of changing percent solids were assessed in order to improve the industrial mill performance and the optimal value should be in the range from 76 to 80%.

Aug 1, 2018

By Marjorie Benegra

This study aims to compare the wear resistance assessed in rubber wheel abrasion test of nickel aluminide coatings deposited by for Plasma Transferred Arc (PTA) and High Velocity Oxigen Fuel (HVOF) manufacturing, using the same raw material. A nickel aluminide powder was atomized and deposited on 316L steel plate substrate. After deposition, some specimens were submitted to a heat treating (1200 °C for 24 h followed by 760°C for 24 h). The coatings deposited using PTA developed different microstructures due to the incorporation of substrate elements, its performance was better than the HVOF coatings, although their Vickers hardness was similar. After heat treating, a significant variation in hardness and wear resistance was observed. For PTA specimens, there were decrease in hardness of 35%, while for HVOF ones this drop was approximately 20%. Nonetheless, the effect of thermal exposure in wear resistance was quite different: an increase of 21% was observed for HVOF coatings, while a reduction of 20% occurred in PTA ones. Microstructures modifications in PTA coatings were significant for their wear resistance. On the other hand, the reduction of porosity and sintering were responsible for a better performance of heat-treated HVOF coatings.

Jul 31, 2018

By Edo Engel

Blast furnace No. 3 at Zaporizhstal in Zaporozhye is rebuilt in 2016-2017. The Ukrainian company is targeting increased production and availability, mainly through the use of new technology. Zaporizhstal awarded a contract for a new Top Charging Unit to Danieli Corus, after comparing all available technologies. Reliability of the chosen charging device is pivotal, since long outages may be required for maintenance/replacement jobs, which strongly affects the availability of the blast furnace. This article describes the Top Charging Unit including DANCU (Danieli Charging Unit) - a robust hydraulic system. The main focus employed by Danieli and Danieli Corus during the development of this system has been availability and maintainability of equipment. This chute type charging unit has only few major moving parts, none of which is complex or vulnerable. The article also describes the main challenges of the project at Zaporizhstal, such as the use of hot sinter.

Oct 30, 2017

By Jörg Busch

The essential pre-requisite for attaining the high quality of product required from high-speed continuous production processes is the use of new measurement and control technologies. High availability and reproducible measuring results ensure the high level of process stability necessary for full continuous operation. The requirements for the optimisation of quality across the complete production process and for quality analysis systems will be discussed. This report will present examples of basic and new measurement technologies in Cold Rolling Mills and Processing Lines. The following gauging systems will be discussed in detail: Strip tension meter, roll force measurements, weighing systems and shapemeter rolls. The measuring and control systems in this presentation must be seen as high-tech solutions in the field of processing technology. The measuring methods and technologies described are, together with optimised process models and precision control loops and actuators, the main pre-requisites for achieving the quality of product required from high-speed continuous production processes. Interconnected quality management systems enable optimisation across the complete production process.

Jul 30, 2018

By Moisés Paulo Teixeira

The use of tailings for the synthesis of new materials is a worldwide concern today. This paper approaches the utilization of tailings of soapstone (steatite) in order to produce ceramics. The results show that the addition of soapstone in a ratio over 20% in the ceramic mass has enhanced the bending resistance of the ceramic samples when they were fired at temperatures of 900°C or 1000°C.

Oct 30, 2017

By Mariano de Córdova

In this paper, the coke oven life prolongation technology is reviewed from different points of view: blend design; battery heating; operational control; refractory maintenance. A summary of major inspections in critical areas, for the evaluation of the battery conservation situation is presented. A discussion on tools for the diagnostics of the degree of damage is carried out.

Aug 16, 2017

By Haruki Inami, Takashi Ishida, Kazuhiro Ohara, Hiroyuki Imanari

The highly competitive business environment of the international metals industry is driving demand for more cost-effective operation of steel making facilities, rolling mills, and strip processing lines. Achieving stable operation is vital if the steel industry is to produce high-quality products constantly and productively. In recent years, advances in computer processing speeds, data acquisition rates, and data storage capacity have rapidly led to greater use of the new technologies of big data, analytics, the IoT, and AI by control system designers and process engineers, and the introduction of industrial applications. The “Smart Rolling Mill” solutions for hot strip mills have been developed by our group with the goal of achieving sophisticated, state of the art, and automated operation in steel rolling mills. The various solution engines improve process stability, increase the performance of mill equipment, and provide improved process control. These solution engines are based on extensive knowledge of the rolling process and the associated control systems. Two solution engines in particular are the diagnosis systems for rolling condition and for product quality that contribute to cost-effective operation and lower yield loss. This paper focuses on the diagnosis systems for rolling condition and for product quality in hot strip mills. Advanced information technologies using big data analytics and machine learning are applied to real-time data collected from the automation system that controls operation and the rolling process. We have developed diagnosis solutions for rolling condition and product quality utilizing predictive and clustering diagnosis. Predictive diagnosis prevents serious problems by detecting changes in the state of the plant or in the rolling condition. Clustering diagnosis classifies patterns of fluctuation in product quality trend charts, providing effective tuning guidance for improving product quality. This paper describes these applications with several examples.

Oct 1, 2019

By Ernesto Gustavo Maffia

En la actualidad, el moldeo por inyección es una tecnología muy utilizada en el procesamiento del plástico pues permite fabricar formas geométricas complejas. Para fabricar los moldes se utiliza ampliamente la aleación C17200 (Cu-2%Be), pero están en desarrollo algunas alternativas con aleaciones base cobre libres de berilio, que tienen valores de dureza por encima de los 30 Rockwell C y buena conductividad. Las aleaciones base de cobre, tipo CuNiSiCr son las más adecuadas como reemplazo. El siguiente trabajo trata del estudio y desarrollo del proceso de fabricación, por fusión, colado y conformado, de una aleación tipo CuNiSiCr de alta dureza y buena conductividad para ser utilizada en la fabricación de moldes de inyección para la industria del plástico. Los resultados preliminares de esta investigación demuestran que a través del aumento sistemático en el contenido de níquel y silicio se consigue un aumento de la dureza (>32 Rockwell C) y una aceptable conductividad eléctrica (˜25%IACS). El fenómeno segregación interfiere fuertemente en los tratamientos termomecánicos, pues se forma una segunda fase interdendrítica, de características frágiles, que genera fracturas en el conformado. Los resultados demuestran que la aplicación del recocido total y control de la temperatura durante la forja minimizan este problema.

Aug 7, 2018

By Christoph Aichinger

A smart combination – Primetals Technologies developed the Circular Pelletizing Technology (CPT), which is a combination of the well-proven travelling-grate pelletizing technology with the design of a circular dip rail cooler of modern sinter plants. The overall space requirement and the installed weight for a CPT plant is significantly less compared to conventional technologies and by that CPT is a very attractive alternative for new projects.

Aug 16, 2017

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019