Search Documents

By C. Pelley, S. Kelebek, G. Kunzel, S. Gregersen, M. Pollanen

A series of small-scale tests was conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the material properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Poisson’s ratio, Pwave, S-wave velocity, point load test index, crushing, and grinding work indices were evaluated for samples without any blasting load and for samples which had received a variety of blast loads ranging from a single impact with a lowstrength detonating cord to a combination of impacts at different times and significant impacts with powder factors close to those used in practical blasts. It was shown that the rock mechanics parameters change even at low impacts, suggesting easier crushing of the rock. Damage values appear to be affected by timing as stress wave superposition affects the damage process. Fragmentation is achieved at higher impact levels while work index modification of the fragments is also observed when high powder factors are used, suggesting improvements in grinding.

Jan 1, 2006

By J. J. Forbes

The activities of the Bureau of Mines include the development and testing of self-contained oxygen breathing apparatus and other devices for respiratory protection, the development and tasting of devices for detecting dangerous or noxious mine atmospheres, and the training of men in the mineral industries in the use and care of this equipment to enable them to render effective service in mine rescue and recovery operations following mine fires and explosions, or under other conditions where irrespirable gases may be found in mines or mining plants. The first use of self-contained oxygen breathing apparatus for com- bating mine fires and explosions in the United States dates back about 30 years. Previous to that time, exploration for any distance ahead of fresh air was virtually impossible without great risk to life; moreover, the men called upon to render service at mine disasters were not well-versed in the properties and physiological effects of gases likely to be encountered. It was also impossible to work ahead of fresh air to restore ventilation, and if many stoppings were blown out by an explosion, air had to be introduced into whole areas or sections at once without knowledge of the conditions ahead; moving an explosive mixture of methane and air over live fire had to

Jan 1, 1938

By J. McCoy

Charged sprays and fog have been evaluated for reducing respirable dust concen¬trations. Charged spray technology was reviewed for effectiveness, equipment and theoretical considerations. A mathematical model was developed for predicting dust reduction effects. Laboratory tests were made showing charged spray is considerably more effective at reducing dust on a unit water basis than hydraulic spray. Positive and negative sprays are equally effective. Combined polarity sprays are considerably less effective than either polarity alone. Little difference in effectiveness by dust type was observed. The charged cloud can present a spark hazard in explosive atmospheres. Due to this spark hazard from the charged droplet cloud this technique must not be used in gassy mines. Predictions were made for field test conditions but confirmation was impossible due to particles resulting from dissolved solides in the spray water. Dissolved or suspended solids in atomizing sprays can result in an increase of the respirable dust burden. Charged sprays are an available dust control technique best suited to applications where water usage must be limited and long contact time between spray and dust is possible.

Jan 1, 1983

By David E. Fogelson

One model each of three different makes of portable displacement seismographs was calibrated on a shaking table capable of 5,000 pounds of force, Calibration tests were conducted in the frequency range of 5 to 200 c.p,s, and in the amplitude range of 0,002 to 0.05 inch peak-to-peak, The seismographs were tested under two mounting conditions: (1) The feet of the instrument were bolted to the shaking table, and (2) the feet were resting on emery cloth affixed to the table, The results of these tests show that, in the frequency range of 5 to 40 c.p,s, and for vibration levels less than 0.2 g, the magnification for all three instruments is constant with input level but varies slightly with frequency. For vibration levels greater than 0.4 g. and for frequencies greater than 40 c.p.s., the magnification of all three instruments shows large variations with frequency and amplitude of table motion.

Jan 1, 1962

By R. Bergstrom

The implementation of a Quality Management System (QMS) or an Environmental Management System (EMS) that conforms to the standards issued by the International Organisation for Standardisation (ISO) no longer needs to result in a bureaucratic nightmare supported by mounds of paperwork. In this sense, this paper describes the Quality Management System that was implemented and demonstrates how the technologies that were developed can be used to satisfy other similar requirements.

Aug 25, 2002

The strippable reserves of bituminous coal and lignite in the United States were calculated in accordance with the prevailing conditions of seam thickness and depth of overburden in each of the several coal-producing areas of the Nation. Within defined limits of seam thickness and depth of overburden, it is estimated that there was a remaining strippable resource of 118 billion tons of raw bituminous coal and lignite as of January 1, 1968. Because of topography, natural and manmade features, and other limitations, only 45 billion tons of the resource are strippable reserves. Of this, 32 billion tons is considered low-sulfur (less than 1 percent), 4 billion tons is medium-sulfur (1 to 2 percent), and 9 billion tons is high-sulfur (over 2 percent) coal. Owing to a cleaning loss affecting that portion of strip coal that is mechanically cleaned, the 45 billion tons of strippable reserves are reduced to 39.6 billion tons of marketable coal. A brief discussion is given for each coal-producing State, summarizing past and present production, historical background, and outlook. Appendix A contains reserve data by State, county, seam, and sulfur content. Appendix B contains the general information and requirements necessary to comply with the current strip mining laws covering 20 States.

Jan 1, 1971

By Jacek Paraszczak

Numerous problems encountered in the mining of narrow vein deposits challenge the productivity, competitiveness and profitability of many mines. Mechanization of mining operations is one of the most important means to ensure the healthy survival of this mining sector. Vein deposits account for nearly all the world's primary silver production, as well as a significant portion of gold, tin, copper lead and zinc. In North America, narrow vein mining constitutes an important sector of the industry. Operators exploiting such deposits are concerned with the most appropriate mining method and equipment to mine in such a way as to minimize waste rock dilution. Unfortunately, most of the equipment available does not meet the additional geological and economical restrictions typical of narrow vein mining. Thus, mining these deposits is labor intensive and can result in low productivity. Consequently, the profitability of many such mines is reduced. Increased mechanization is one of the solutions to ensure their healthy survival. This paper reviews the state-of-the art in mining equipment with reference to narrow vein mining limitations. Problems encountered Geological conditions and economical factors have a decisive impact on the choice of mining method and equipment. Many ore bodies are relatively small, usually erratically distributed, often less than 2 m (6.5 ft) wide, with dips ranging from 0° to 90°. To make things worse, ore body limits are sometimes difficult to determine and the ground is hard and abrasive.

Jan 1, 1992

Several industrial-scale HydroFloat separators have recently been installed at Mosaic?s South Fort Meade beneficiation plant for the purpose of improving phosphate recovery and throughput capacity. This technology was implemented after numerous laboratory, bench-scale and on-site, pilot-scale test campaigns. The results from this detailed test work provided sufficient justification for the complete retrofit of the existing coarse and ultra-coarse flotation cells. Data indicate that the metallurgical results obtained with the full-scale separators are consistent with that obtained during both the bench- and pilot-scale evaluations. The benefits, theory of operation and commissioning of the equipment are also discussed.

Jan 1, 2007

By H. C. van Zyl

Mine water in the Upper Olifants River Catchment in Mpumalanga(upstream of Loskop Dam) is at times discharged into local streams, resulting in local acidification and regional salination of surface water resources. Pollution of surface water can be prevented by collecting and treating mine water to a quality where it could be re-used without restriction (Cleanwater 2020 Initiative). Mine water in the Olifants River Catchment currently amounts to only 4,6% of the total water usage, but contributes 78,4% of the sulphate load. Limestone and lime treatment is the most cost-effective technology for neutralization and partial sulphate removal of acidic/sulphate-rich water to sulphate levels of less than 1500 mg/l due to precipitation of magnesium and removal of the associated sulphate fraction (through gypsum crystallization). Neutralized mine water of this quality may be suitable for irrigation. A number of alternative desalination treatment technologies were investigated (subsequent to gypsum crystallization pre-treatment) where treated mine water must meet more stringent quality requirements (e.g. less than 200 mg/lSO4). The capital cost of these processes varied between R4 million/(Ml/d) and R10million/(Ml/d) and the running cost between R2/m3and R5/m3. Water usage in the Upper Olifants River Catchment currently amounts to 947 Ml/d (including the power stations), and will increase to an estimated 1385 Ml/d by 2020. The additional water demand by2020 (438 Ml/d) will have to be supplied by importation from neighbouring catchments, and more efficient utilization of the local water resources, including excess mine water. Various levels of treatment are required to make mine water suitable for the following potential applications (acceptable treated water sulphate concentration shown in brackets): irrigation (2000 mg/l), coal processing plant (1000 mg/l), general industrial use (500 mg/l), discharge to public streams (500 mg/l), potable use (200 mg/l) and cooling water in power stations (20 to 40 mg/l). The following two options, or a combination thereof, can be considered for management of excess mine water in the Upper Olifants River Catchment: ?Collection and treatment of excess mine water to a quality suitable for selected urban and industrial applications (Option A) ?Collection and treatment of mine water to a quality suitable for irrigation (Option B). The estimated capital and running cost for Option A amounts to R528.5 million and R55.7 million/year, respectively, compared with R68,2 million and R11,9 million/year for Option B. It is recommended that Option B be investigated for implementation in the short to medium-term. Option B was selected due to cost benefits and the initial favourable results obtained by a joint Water Research Commission and Coal Industry initiative where mine water is used for irrigation. Option A may become feasible in the long-term to ensure maximum environ-mental protection and reduced treatment cost as a result of anticipated technological improvements over the next 5 to 10 years.

Jan 1, 2001

By W Skinner, C G. Kelsey, J R. Kelly

The iron ore industry has reached the end of an unprecedented period of expansion triggered by China’s demand for iron ore. Lower ore prices have led producers to focus on optimising mining operations while extracting the maximum tonnage from the infrastructure presently in place or from projects already underway. A rising global surplus is expected to further force ore prices down and lead to output curtailments, which in turn will help to restore market balance. However, investment in the development of new resources and the development of new infrastructure will inevitably become necessary. Making the right decisions in relation to future processing infrastructure in a climate of uncertain demand and price volatility will not be as straightforward as in the past, where expanding the scale of a proposed operation has been the answer to ensuring economic viability. Overall cost and environmental pressures particularly in relation to wet processing will dominate the decision-making process. IMP Technologies (IMPTEC) has anticipated the need for a dry low cost processing alternative, which can open the way for the development of lower grade magnetite deposits and ensure the sustainability of processing in Australia. The lower grade magnetite deposits are generally fine grained and require grinding to p80 of 30 to 40 microns. Historically, the cost of grinding to these sizes has been and remains a key factor determining the economic viability of a magnetite processing operation. The IMPTEC Super-fine Crusher and Cyclomag Separator are the key components of a proposed radically simplified dry processing alternative, which addresses both cost and environmental issues. This paper reports on the results of pilot super-fine crushing and cyclomag separation test work, focused on supporting the feasibility of the proposed dry processing route for the production of high-grade pellet plant feed from fine grained low-grade magnetic ores.CITATION:Kelsey, C G, Kelly, J R and Skinner, W, 2017. Dry processing of magnetic iron ores – addressing cost and environmental issues, in Proceedings Iron Ore 2017, pp 215–220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Bruno Gemmi

A new warehouse built with prefabricated components over an area underlined by soft marine soil deposits started showing differential settlements well before its completion. Its 103 spread footings carrying up to 4,000kN (450t) axial loads had been cast on jet-grouted columns extending and penetrating a layer of sand at a depth of 10m (33ft). Investigations performed to assess the wholeness and consistency of the jet-grouted columns revealed a state of loose jet-grouted masses and uncontrolled, off target migrations of the jet-grouting. Most of the jet-grouting itself was settling. The following remedial solutions were suggested: 1. Construction of new and better controlled jet-grouted columns. 2. Cement-based soil grouting. 3. Expanding resin injections. 4. Minipiles drilled-through the existing footings and reaching into a denser layer of sand existing at 23m below grade. Remedial solution 1. was immediately discarded due to cost and the possibility of a repeating failure in this non-granular and highly compressible soil. Tests of remedial solutions 2. and 3. were carried out. The outcome of the grouting was monitored by Electro Resistivity Tomography (ERT) (Bares et al., 2003), an innovative 3D electro tomography procedure showing where grout had been actually placed and its migrations off target. A successful 4,000kN (450t) load tests confirmed the validity of the solution. Finally, upon the completion of a successful load test, solution 4. was chosen. It supplied the highest degree of reliability thanks to the ease of controlling the final and actual location of the minipiles and to the higher safety factor provided. All remedial work to install the minipiles was eventually performed inside the building. Additional load tests and settlement measurements confirmed the adequacy and success of the chosen solution.

Jan 1, 2011

By David S. Yantek

Miners in underground coal mines experience prolonged exposure to high noise levels, often with A-weighted sound levels in excess of 90 dB. Field tests have shown that the continuous miner conveyor is a dominant noise source. This paper will identify the most significant noise-radiating surfaces on the continuous miner tail section using vibration levels and surface areas to estimate the sound power levels of each surface. In addition, using five test cases, this study will examine the effects of three engineering noise controls on the surface-averaged vibration levels and average sound levels measured with four microphones located two meters from the tail section. The noise-radiating surfaces of the conveyor’s tail section include the top and bottom decks, the sideboards, and the flex plates. Emphasis is placed on the changes in the estimated sound power levels in the 500 – 2500 Hz 1/3-octave bands since this frequency range accounts for 80-85% of the sound energy near the tail section. The results show that the bottom deck is the most significant noise radiator for the untreated miner. Installing a coated bottom deck reduces the estimated sound power level radiated from the bottom deck by 11 dB and the average sound level by 2 dB. Using a coated tail roller results in reductions of the estimated sound power levels for individual components from 1 to 4 dBand reduces the average sound level by 2 dB. Coating the slide plate has little effect on both the estimated radiated sound power levels and the average sound level. The test results indicate that modifications that reduce flex plate vibration and reduce energy transfer from the tail roller into the tail section will be effective in reducing noise when combined with a coated tail roller and coated return deck.

By C. F. Lucks, W. D. Wood, H. W. Deem

Electrical ad thermal-conductivity measurements have been made on titanium and 6 titanium alloys. The following expression was derived for calculating thermal conductivity from electrical conductivity: K = 0.626 s T x 10-8 + 0.00497 where K = thermal conductivity, cal sec-1 cm-2 cm0C-1 s = electrical conductivity, ohm-]cm-1 T = temperature, deg Kelvin This expression gives calculated thermal conductivities that are not in error by more than 10 pct from the experimental values for A-55 titanium and the 6 alloys measured; namely, A-110AT, C-110M, C-130AM, Ti-6A1-4V, Ti-140A, and Ti-155A, which are representative of the presently available commercial a and a-ß titanium alloys. THERMAL conduction in a gas, liquid, or amorphous solid is accomplished by energy diffusion from molecule to molecule, a relatively slow process. For this reason, such materials have a low thermal conductivity. When a material is crystalline, there is in addition a heat transfer by a vibratory motion of the crystal lattice. It is the contribution of this lattice conduction that makes a crystal a much better conductor than a gas, liquid, or amorphous solid. Lattice conduction, however, does not account for the relatively enormous thermal conductivity of a metal. This is explained by the freedom of movement of valence electrons. These valence electrons drift in a metal in a direction toward a drop in electrical potential and, to a lesser degree, in the direction of a temperature drop in the metal. Since both the electrical and thermal conductivities of a metal depend upon the presence of free electrons, there should be some relatively simple relation between the two. Wiedemann and Franz in 1653 first discovered an approximate empirical relation between the electrical and thermal conductivities of metals at the same temperature. This ratio varies appreciably with temperature, and Lorenz later showed that by adding a temperature factor to the Wiedemann-Franz ratio the value of K/(s T) is constant, where K is the thermal conductivity, a the electrical conductivity, and T the absolute temperature. This Lorenz constant shows a greater variation for alloys than it does for pure metals, the ratio increasing slightly as the proportion of alloying elements increases. It has been found that a closer correlation between electrical conductivity and thermal conductivity can be obtained by means of an equation of the form K - A s T + B [1] where A and B are constants. In this equation the term AsT is the contribution of electronic conduction and B is the contribution of lattice conduction to the total thermal conductivity. EXPERIMENTAL MEASUREMENTS Electrical-resistivity and thermal-conductivity measurements on titanium and 6 titanium alloys serve as the basis for determining an equation of the K = AsT + B type for titanium alloys. Specimens—Table I shows nominal compositions of the 7 metals on which electrical and thermal conductivities were measured. The electrical and thermal-conductivity specimens for each alloy were taken from stock of the same heat and usually from adjacent sections of the same bar. All of the metals measured were in a mill-annealed condition. Methods—Electrical-resistivity measurements

Jan 1, 1959

By A. Asadi

Subsidence phenomenon as an unwanted consequence of underground mining can cause problems for environment and surface structures in mine area. Surface subsidence prediction for inclined and steep seams has been given less attention than horizontal seams due to the difficulties involved in the extraction of such coal-seams. This paper introduces a new profile function method for prediction of surface subsidence due to inclined coal-seam mining. The results of calculation with the new function indicate that the predicted value has good agreement with the measured data. Keywords: subsidence; coalmining; caving mining methods; longwall mining; profile function.

Jan 1, 2005

By R. John Caulfield

The primary water supply system for the City of San Francisco and adjacent peninsula areas consists of aging and deteriorated pipelines crossing under the San Francisco Bay (the Bay). This system is highly vulnerable to seismic damage from the nearby San Andreas and Hayward fault zones. The Bay Tunnel Project will replace the existing system with a 8-km-long (5-mi-long) tunnel underneath the Bay. The tunnel will be constructed using earth pressure balance methods and will have a two-pass lining system of precast concrete bolted, gasketed segments for initial support, and a welded steel pipe final lining. The project challenges include tunneling through both soft ground and rock conditions without any intermediate shaft access over the entire alignment. Seismic performance criteria include maintaining service flows after a large earthquake.

By Amauri Garcia, Rodrigo Valenzuela Reyes, Noé Cheung, José Eduardo Spinelli, Leonardo Fernandes Gomes, Rafael Kakitani

"The present research work deals with directional solidification (DS) of both Al-15wt.%Si and Al-15wt.%Si-1.5wt.%Mg alloys and further characterization of the related microstructures. The growth of refined primary Si and refined eutectic is well-known as positive in order to improve mechanical properties of the Al-Si based alloys. Alloying is also an effective method to strengthen the Al-Si based alloys, in which Mg is considered an important alloying element. However, lack of investigation regarding the effects of Mg on microstructure of these alloys is noted. So, in the present research work emphasis is given on both dendritic and eutectic growth being affected by solidification kinetics (V-growth rate and G-thermal gradient) during transient directional solidification. Experimental evolutions of microstructural spacing of both alloys have been determined which becomes possible to understand the effects of Mg coupled with the effects of growth rate on the final microstructural arrangements. A direct comparison of the tensile mechanical properties obtained for the alloys is also performed. It is shown by these correlations that the addition of Mg generally improves the tensile mechanical resistance with a minor decrease in ductility. Furthermore, the Scheil solidification path of the ternary Al-Si-Mg alloy was determined using the computational thermodynamics software Thermo-Calc, resulting in the following sequence of precipitation: Liquid-Si-a (Al)+Si- a(Al)+Si+Mg2Si. This sequence is compared with the experimental microstructure findings.INTRODUCTION Al-Si alloys containing from 4wt.% to 22wt.% Si comprise more than 90% of all Al-based castings. Parts manufactured with these alloys have a wide range of industrial applications due to their excellent castability, crack resistance, good corrosion resistance, good weldability, low density and high strength (Bray, 1976; Zolotorevsky, 2007; Reyes, 2017). Hypereutectic Al-Si alloys are widely used and researched in the automotive and aerospace sectors due to the low coefficient of thermal expansion, resistance at high temperatures, good wear resistance and high strength (Reyes, 2017; Tebib, 2013). Above the equilibrium eutectic composition (~12.5wt.%Si) the amount of primary Si particles becomes significant (Lasa, 2003). In the place of conventional hypoeutectic Al–Si, there is growing interest in hypereutectic Al–Si alloys as a candidate material for the high-quality engines because a higher volume fraction of silicon may bring about superior properties (Matsuura, 2003)"

Jan 1, 2017

By W. W. Culver

The paper explores the substance, circumstances and significance of the Whelpley and Storer Copper Process. The 1866 Whelpley and Storer patent specified a process combining mechanical and chemical engineering. The process called for a down-drafting shaft furnace with a horizontal flue connected at the bottom of the shaft. Powdered sulphide ore was roasted in the shaft and then sent forward fully oxidized to a bath of sulphuric acid and/or calcium chloride. The “water furnace” was developed in Boston, at a time when the city was home to most Michigan copper mining companies. The process was field-tested at Quebec’s Harvey Hill copper mine. In 1865 James Douglas, Jr. took over management of the Harvey Hill mine with the challenge of saving the family investment. He needed a way to make money from low-grade sulphides. Through his relationship with chemist T. Sterry Hunt, Douglas learned of a possible way ahead using the process developed by Whelpley and Storer. The paper confirms the centrality of publications, meetings, and networking in the advancement of metallurgy. The process is of interest historically, as much as anything, because it is one of the pillars of James Douglas’ distinguished career in copper. INTRODUCTION At the 1866 meeting of the American Association for the Advancement of Science (AAAS) in Buffalo, New York, T. Sterry Hunt (1826–1892) read a paper “On the Metallurgical System of Messrs. Whelpley and Storer.” The paper is part of a chain of events that constitute the foundation of James Douglas’ (1837–1918) success in the copper mining industry. To understand the career of Douglas over the early years of modern copper mining, we must necessarily start with Whelpley and Storer. Going back to Hunt’s paper, he concluded his remarks by asserting that the Whelpley and Storer Process was “capable of such wide and varied application, that it is probably destined to have a very important influence on the industry of the world” (Hunt, 1867a). He reached this conclusion reasoning that the process had overcome a critical metallurgical hurdle (Hunt, 1867a). Hunt, a geo-chemist in modern terms, recalled that the chemist of those years easily separated copper from “sulphuretted” ores by converting it to a soluble salt from which pure metal was precipitated by “an equivalent of iron.” The problem was to “…apply this principle in the working of copper ores on a great scale...” (Hunt, 1867a). Hunt noted that this very problem had “…engaged the attention of many metallurgists, and has given rise to various processes for obtaining copper by the moist way, many of which are nearly or quite perfect in their operation, but are lacking in practicability and cheapness” (Hunt, 1867a). Hunt thought Whelpley and Storer had overcome the low-grade sulphide hurdle with a commercially viable engineering breakthrough. Yet in the history of copper metallurgy, the process is missing. What happened?

Jan 1, 2019

To be able to continuously monitor the noise to which underground workers are exposed as a better way to help prevent hearing damage. The Approach: The Bureau of Mines has developed a Time-Resolved Audio Dosimeter which can be worn by miners to record noise level every 30 seconds and store It in a miniature solid state memory. Figure 1 is a photo of the dosimeter. [ ] How It Works: Acoustical noise is picked up by a micro-phone and fed to a sound level meter which produces a d-c voltage proportional to the A-weighted sound pressure level. (As specified by federal regulations, the A-weighted sound pres-sure level approximates the response of the ear by discounting the higher and lower frequency components of the noise.) This d-c voltage controls an oscillator which, together with related circuitry, produces a pulse train having a frequency that's proportional to the noise level.

Jan 1, 1975

In 1960, the Secretary of the Interior, acting under the provisions of Public Law 454, 80th Congress, appointed a Lignite Advisory Committee to aid in programming research on coal (lignite) of the north-central area. The chairman of this committee is the Secretary of the Interior or his delegated representative, and in all meetings held during 1960 and 1961, the Director of the Bureau of Mines, Marling J. Ankeny, has presided. The members of this committee were R. W. Rovelstad, President, Baukol-Noonan, Inc., Noonan, N. Dak. W. E. Keller, Vice President, Northwest Division, Truax-Traer Coal Co., Minneapolis, Minn. A. M. Cooley, Professor of Chemical Engineering, University of North Dakota, Grand Forks; N. Dak.

Jan 1, 1963

By W. D. Maier, H. V. Eales

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. A lithological and geochemical study revealed significant lateral variation of the interval over 170 km of strike, from about 30 m at the Union Section to 220 m near Brits. The cumulates also become more evolved and leucocratic with distance from the Union Section both towards the NE (Amandelbult) and SE (Impala, Rustenburg and Brits). It is inferred that the persistent heat flux from a putative major feeder zone near the Union Section impaired deposition of felsic cumulates in the vicinity, delaying crystallisation of successive phases in parts of the chamber near the feeder. New influxes were therefore deposited on a footwall of varying thickness and lithology in response to different degrees of crystallisation and accumulation along strike. The development of cyclic units of chromitite, harzburgite, pyroxenite, norite and anorthosite was interrupted at different stages in different parts of the chamber

Apr 1, 1994