Search Documents

By Vince Luongo

PROJECT DESCRIPTION The York Durham Sanitary System (YDSS) Interceptor in the Town of Richmond Hill located just north of Toronto, Ontario, Canada will see the construction of a tunnel extending along 19th Avenue for a length of approximately 3.8 Km from Yonge Street, east to Leslie Street and will have a minimum internal diameter of 2.1 m. t to Leslie Street and will have a minimum internal diameter of 2.1 m. The tunnel will connect into four shafts, for which two of the shafts will be constructed using the slurry wall construction method given the high water table and difficult ground conditions encountered at these locations. The two shafts noted as Access Shaft No. 2 and No. 3 were designed and constructed to meet regulatory conditions, which required a sealed shaft construction method. GEOGRAPHICAL PROFILE The ground conditions in the Toronto region consist predominately of glacial till, glaciolacustrine and glaciofluvial sand, silt and clay deposits, and beach sands and gravels. The shallow geological formation found in the project area consists of four types of deposits: Oak Ridge Morain deposits, Halton Till, Glacial lake deposits and Organic soils. The Oak Ridge Morain is the dominant deposit encountered along the tunnel alignment. This formation consists of three deposits: The Upper Till, Middle Sand and the Lower Till. Standard penetration tests (SPT) carried out in these deposits measured N-values ranging from 2 to more than 100 blows/300mm which indicate very loose to very dense soil conditions. The Middle Sand deposit will be the dominant feature within the slurry wall construction at access shafts 2 and 3. Access Shaft 3 The base of the slurry wall will be 20.5 M below the ground surface. Slurry wall excavation will be within peat and organic soils found at the upper 3 M, followed by 5 M of the Upper Till. The remainder of the excavation will be within the Middle Sand. The piezometric head elevation is found at the ground surface. Access Shaft 2 The base of the slurry wall will be 22.5 M below the ground surface. Slurry wall excavation will be entirely within the Middle Sand 2.The piezometric head elevation is found at 7 M below the ground surface.

Jan 1, 2007

By Chaojun Fan, Du Wenzhang, Sheng Li, Hong-Hong Shi

"Coal and gas outburst is an extremely complex dynamic disaster in coal mine production process which will damage casualties, equipment facilities and disorder the ventilation system by suddenly ejecting a great amount of coal and gas into roadway or working face. This paper analyzed the interaction among the three essential elements of coal and gas outburst dynamic system. A stress-seepage-damage coupling model was established which can be used to simulate the evolution of the dynamical system, and then the size scale of coal and gas outburst dynamical system was investigated. Results show that the dynamical system is consisted of three essential elements, coal-gas medium (material basis), geology dynamic environment (internal motivation) and mining disturbance (external motivation). On the case of C13 coal seam in Panyi mine, the dynamical system exists in the range of 8-12 m in front of advancing face. The size scale will be larger where there are large geologic structures. This research plays an important guiding role for developing measures of coal and gas outburst prediction and prevention. INTRODUCTIONCoal and gas outbursts are a complicated mine gas dynamic phenomenon that pose a serious threat to coal mine safety production. Since the first recorded coal and gas outburst occurring in Isaac coal mine of the Lule coal field in 1843, more than 40,000 outbursts have occurred in the world. China ranks first in outburst frequency and intensity. In recent 20 years, China on average increases 37 pairs of coal mines and more than 280 times outburst accidents every year (Yan, 2013). The coal and gas outburst occurred on Oct 20, 2004 in Daping Coal Mine, Zhengzhou Coal Group, caused serious gas explosions and ejected 1,894 tons of coal into the face, causing 148 fatalities. In recent years, despite implementation of numerous control measures, coal and gas outburst still occur frequently ash mining depth and mining intensity increase. The outburst mechanisms can be summarized in the following four aspects: the gas leading role hypothesis, the geostress leading role hypothesis, the chemical effect hypothesis, and combination hypothesis. The last hypothesis has won the acceptance of most scholars who consider that an outburst is the result of combined effect of stress, gas and coal (Yu, 1992).Numerous experimental measurements and numerical simulations were conducted to investigate the permeability and damage development process in coal seam. Sobczyk, et al (2011) carried out a laboratory research of the influence of sorption processes on gas stresses leading to coal and gas outbursts. Wang, et al (2013, 2015) conducted laboratory experiments to investigate the rapid decompression and desorption induced energetic failure in coal using a shock tube apparatus. Xu, et al (2006) developed a coupled gas flow and solid deformation numerical model and applied to simulate the coal and gas outbursts in underground coal mines using RFPA2D-Gasflow. An, et al (2013) and Xue (2014) analyzed major parameters and the effect of gas desorption on outburst initiation and established a model of gas migration and mechanical processes during excavation."

Jan 1, 2016

By S. Frimpong, S. R. Dindarloo

Material handling in open pit mining accounts for about 50% of production costs. The selection and deployment of efficient, safe, and economic loading and haulage systems is thus critical to the production process. The problems of truck and shovel selection and sizing include determination of the optimal number and capacities of haulage and loading units, as well as their allocation and operational strategies. Critical survey and analysis of the literature has shown that deterministic, stochastic, and experimental approaches to these problems result in considerably different outputs. This paper presents a comprehensive simulation framework for the problem of truck and shovel selection and sizing based on the random processes underlying the network-continuous-discrete event nature of the mining operation. The framework builds on previous research in this field and attempts to address limitations of available methodologies in the form of a comprehensive algorithm. To test the validity of the framework a large open pit mine was evaluated. The stochastic processes governing the uncertainties underlying the material loading and haulage input variables were defined and built into the stochastic model. Discrete event simulation was used to simulate the stochastic model. The proposed model resulted in several modifications to the case study.

Jan 1, 2015

"The measurement of error in assays collected as part of a mineral exploration program or mining operation historically has been undertaken in a variety of ways. Different parameters have been used to describe the magnitude of relative error, and each of these parameters is related to the standard measure of relative error, the coefficient of variation. Calculation of the coefficient of variation can be undertaken in a variety of ways; however, only one produces unbiased estimates of measurement error: the root mean square coefficient of variation calculated from the individual coefficients of variation.Thompson and Howarth’s error analysis approach has also been used to describe measurement error. However, because this approach utilizes a regression line to describe error, it provides a substantially different measure of error than the root mean square coefficient of variation. Furthermore, because regression is used, Thompson and Howarth’s results should only be used for estimating error in individual samples, and not for describing the average error in a data set. As a result, Thompson and Howarth’s results should not be used to determine the magnitudes of component errors introduced during geochemical sampling, preparation, and analysis.Finally, the standard error on the coefficient of variation is derived, and it is shown that very poor estimates of relative error are obtained from duplicate data. As a result, geoscientists seeking to determine the average relative error in a data set should use a very large number of duplicate samples to make this estimate, particularly if the average relative error is large."

Jan 1, 2007

By S. O. Bada

Coal samples taken from the No. 2 Seam and No. 4 Seam in a South African colliery were tested in a rotary triboelectrostatic separator. The two-stage triboelectrostatic separation results using the -177 µm size fraction reduced No. 2 Seam coal containing about 30.4 per cent ash to a clean product of 8.9 per cent and 13.1 per cent ash with combustible recoveries of 9.6 per cent and 30.7 per cent respectively. The same separation approach on No. 4 seam feed coal, which contained 36 per cent ash, produced a clean coal product with 10.8 per cent ash at a combustible recovery of 6.0 per cent. Petrographic tests show a significant improvement in the vitrinite content and a reduction in visible minerals encountered when using the triboelectrostatic separator, with about 53 per cent vitrinite reporting to the clean fraction for No. 2 Seam compared to the feed content of 21 per cent, and a 54 per cent vitrinite in the clean No. 4 Seam from a feed content of 21 per cent. Significant sulphur reductions were also observed after separation in both coal samples, with a better separation in the second-stage coal products.

Jan 1, 2012

By Bengt H. Fellenius

Session 2, Deep Foundation without Soil Excavation, has attracted no fewer than 22 papers dealing with subjects from soil improvement by grouting, injection, and deep mixing techniques through vibroflotation and special piles, including aspects pertaining to conventional driven and bored piles. In the short time available, it is not possible to both do justice to the papers and provide a critical review of the state-of-the-art. Instead, to meet the objective of making the next half hour worthwhile to the audience, I have chosen to comment on a few special points brought forward in the papers and thereafter to discuss more in detail a couple of aspects I have deemed to be of general interest. Four papers deal with jet-grouting, injection, and deep mixing techniques: DOMSKI, J. J. Reinforcement of subsoil under the foundations of historical buildings in Cracow using deep injection technique. RESTELLI, A. B, BERTERO, M., and LODIGIANI, E. Deep mixing technology to improve the bearing capacity of a very soft clayey soil under an earth embankment.

Jan 1, 1994

By Richard J. Mainiero, James H. Rowland III, Marcia L. Harris

This paper reviews the potential hazards posed by the toxic fumes produced by detonating explosives in surface mining and construction operations. Blasting operations produce both toxic and nontoxic gaseous products; the toxic being mainly carbon monoxide (CO) and the oxides of nitrogen (NOx). The quantity of toxic gases produced by an explosive is affected by formulation, confinement, age of the explosive, and contamination of the explosive with water or drill cuttings, among others. Techniques to protect workers and the public from the potential hazards of explosive-related toxic fumes are discussed. These include: • Minimizing the quantity of toxic fumes produced. • Determining where the fumes may go so workers and neighbors can be moved out of harm’s way. • Preventing the fumes from moving towards workers and neighbors. • Monitoring the air near workers and neighbors so they can be relocated if fumes appear. • Ventilating structures or confined spaces until CO falls below a hazardous concentration.

By Gaulton R

The Commission maintains a data base first computerised in 1957 and containing information from over 18 000 boreholes located mainly in the Latrobe Valley area. Some of the borehole derived information dates from the turn of the century, although most of it has been collected as a result of Commission investigations conducted over the past 40 years. The Resource Data Base contains not only information gained directly from the drilling itself but includes the results of chemical and physical testing on many hundreds of thousands of samples retrieved from boreholes. Replacement value of the Resource Data Base has been estimated to be around $200 million, and it's integrity and accessibility is clearly of paramount importance, not only to existing mining and power generating functions but to the future evaluation and use of the vast brown coal Resource.

Jan 1, 1992

IN all wet concentration processes it is of primary importance to determine to what degree the crushing must be carried in order to obtain the maximum profit per ton of ore milled.To effect a clean separation, either by gravity or flotation treatment, between either one valuable sulphide from another, or a sUlphide from the gangue, the ore must have been subjected to grinding to such an extent that the particles to be separated are completely liberated from each other.Insufficient crushing will result in either an incomplete separation of the sulphides from each other, and thus a loss of the one sulphide in the other, or else a loss of the valuable sulphide in the gangue.This being so, the question arises whether the added cost of extra crushing would be economically warranted by the increased recovery consequent on such a step.

Jan 1, 1927

By Stuart McTavish

"Noranda's Goldstream mine is a 1,500 ton per day copper-zinc mine located 60 miles north of Revelstoke, B.C.The orebody which contains 3.69% Cu and 2.69% Zn was discovered in 1972. Construction of the mine and mill was completed in 1982 and start up was achieved in May 1983.This paper will describe the flowsheet and related equipment 1n the crusher and mill, in particular the dewatering section where two Larox pressure filters are used to dry the concentrates.INTRODUCTIONThe Goldstrean property is located 60 miles north of Revelstoke, B.C. in the Goldstream River Valley (Figure #1). It was discovered during the construction of a logging road in 1972. Exploratory drilling was initiated in 1975, and in 1976 a portal was collared to obtain underground data. Samples were taken from the underground workings for metallurgical bench tests and a pilot plant run.Due to economic conditions, the decision to go into production was delayed until 1980. Concentrator construction and underground development progressed simultaneously during 1981 and 1982, and were completed by the end of 1982. Start up of the concentrator was achieved on May 2, 1983.The ore typically contains about 40% sulphides, which are chalcopyrite 10%, sphaletite 6%, pyrrhotite 20%, and pyrite less than 5%. The sulphide minerals have a high degree of intergrowth. Most of the sphalerite occurs in micron sized grains which are embedded in the pyrrhotite and, to a lesser degree in the chalcopyrite. There is also some fine dissemination of the chalcopyrite in the pyrrhotite. The waste rock is made up of about 30% quartz, 20% guange silicates, and 10% carbonates. The ore has a specific gravity of 3.2 and a natural pH of 8.2."

Jan 1, 1985

The widely accepted kinetic model for the gaseous reduction of hematite is critically examined. The formation of the wustite layer during internal reduction cannot be explained in terms of solid-state diffusion. Present evidence indicates the existence of a micropore system in the wustite adjacent to the magnetite with the gas/solid type of reaction occurring not only at the iron/wustite interface but also at the wustite/magnetite interface. During the partial reduction of dense hematite pellets, in a controlled atmosphere, porous magnetite and wustite are formed as products. The mean pore size, as measured by mercury injection, increases with time at constant temperature and with temperature increase over the range 6500C to 950°C. The sizes of the pores indicate that Knudsen diffusion is the principal gaseous transport mechanism across thick layers of magnetite or wustite.The kinetics of the gaseous reduction to iron are consistent with a mixed control mechanism involving the interaction of gaseous diffusion effects with a first order reversible chemical reaction at the iron/wustite interface. Because of the larger pore sizes in the iron layers, ordinary molecular gaseous diffusion must be the principal transport mechanism. The usual experimental methods used for establishing the validity of chemical rate ~ontrol are incapable of differentiating between the mixed control- mechanism and exclusive chemical control.Some implications of mixed control kinetics are developed, including a predicted independence of rate on reducing gas pressure at higher pressures.INTRODUCTIONAn extensive literature review of the reduction of iron oxides has been compiled recently by Themelis and Gauvin (1962). From the large number of papers published and the widely divergent opinions of workers in this field, it appears that a simple unified quantitative analysis of reduction kinetics is not possible. The aim of the present paper is to show that a major cause of confusion is due to the attempts of many workers to interpret experimentally observed reaction rates in terms of a single rate controlling mechanism without due regard to other rate processes which must occur simultaneously.Some of the differences in behaviour reported for particles...

Jan 1, 1964

By Charles L. Allie

Since Reserve Mining Co. began commercial operations at Silver Bay, MN, some 25 years ago, major improvements in taconite processing technology have become available. In addition, significant new government standards have been imposed on industrial operations. By implementing a $370-million modernization program, Reserve was able to accomplish two major company objectives: the quality of concentrates produced from the Peter Mitchell mine has improved, and the operation meets both present and foreseeable environmental standards. Process modifications at Reserve were designed to: •Reduce the pellet silica content from 9% to 5%; •Increase the pellet iron content from 62.5% to 65.8%; •Implement a tailings disposal system utilizing "best available technology" water quality controls; and •Reduce air emissions by installing "best available technology" air emission controls. By adding dry cobbing, fine screening, and flotation to the concentrating process, pellet silica content has been reduced; the process reclaims and reuses all process waters; all tailings are stored in a zero discharge tailings basin; and all air emission standards are being met. Initial Beneficiation at Silver Bay Reserve's Peter Mitchell mine at Babbitt, MN, is on the eastern end of the Biwabik iron formation. The open-pit mine is approximately 16 km long, 0.8 km wide, and presently has a maximum depth of about 50 m. Principal constituents of the ore body are magnetite, quartz, and iron-magnesium silicates. The company's large commercial plant began operating at Silver Bay, 75 rail km from the mine, in 1955. Facilities have historically had the capacity to process 31.5 Mt/a of taconite, containing an average 24% magnetic iron, into 11 Mt/a of iron ore pellets. Reserve's initial beneficiation process-which existed up to early 1979-consisted of two crushing stages at the Babbitt mine site, two additional crushing and screening stages at Silver Bay, grinding in a conventional rod-ball¬regrind mill circuit, size classification with cyclones, and concentration with magnetic and hydraulic separators. Concentrate produced by that circuit assayed 65% iron and 8.5% silica, with a screen analysis of 94% -44 µm, and a surface area of 9300 cm2/cm3. Pellets produced from this concentrate assayed 62.5% iron and 9% silica (dry basis). Construction began in 1977 to modify Reserve's operation. Process modifications were designed from pilot scale operations that had been operated and researched by Reserve for more than 10 years. There were two design restraints imposed on the process: economic constraints that Reserve continue to use much of the existing processes and structures in the new operation; and a substantial number of government-imposed permit constraints. In effect, the tailings process was designed first and then a concentrating process was developed that would "fit" the tailings disposal system. Operation of the modified process began in June 1980. Crushing Remains Unchanged No changes in process flow were made at either the Babbitt mine and crushing plant or at the Silver Bay fine crusher. Gyratory crushers reduce run-of-mine taconite to -90 mm-diam at the mine. Taconite is then transported to Silver Bay by intra-plant railroad. There are 10 fine crushing lines. Each consists of a double deck screen, followed by a heavy duty short head crusher, a second double deck screen, and second short head crusher. All screen undersize material bypasses the crushing lines, resulting in an open circuit crushing process. Fine crusher product is approximately 98% - 20 mm, 80% -12 mm, and 50% -10 mm in diameter. Each fine crusher line processes about 400 t/h of crude taconite. Cobbing Provides Aggregate for Tailings Dams The first major process change was the addition of dry cobbing, a dry magnetic separation step between the fine crusher and concentrator. Dry cobbing serves two major purposes in the new process. Its principal function is to provide large volumes of dry coarse aggregate for use in construction of tailings dams. This process rejects about 20% of the fine crusher product as tailings with a size analysis of 98% -20 mm and 50% - 10 mm. These tailings are free draining and have high frictional shear strengths-two key requirements for dam building aggregates. Fine crusher product is conveyed to a new dry cobbing building. Here crushed ore is discharged into one of two 30-minute capacity surge bins. Crushed ore is withdrawn by 12 constant speed conveyor belts; each discharges 500 t of crushed taconite into a dry cobbing machine. Each machine consists of a 3-m-long riffle splitter and two vari-

Jan 12, 1980

By R. D. Pehlke, J. V. Gluck

AS a portion of a general study of liquid-metal thermodynamics, high-temperature galvanic cells were used to study the effect of added dilute solutes on the activity of zinc in dilute solution with molten bismuth in the range 450° to 650°C. 1,2 The cells were of the type The experimental procedures have been described previously.1 In the course of studies conducted in the bismuth-rich corner of the systems Bi-Zn-Au and Bi-Zn-Cu, marked discontinuities were observed in the electromotive force-temperature relations for a number of the experimental compositions. Above the discontinuity temperatures, the relations, which were linear, exhibited slopes similar to the binary alloy of the same mole fraction zinc, as shown in Figs. I and 2. Below the discontinuity temperatures, the slopes were markedly different, but the relations remained linear. In general, as the amount of the third eletnent was increased, the slope of the lower portion of the relations tended to become less positive. The slopes of electromotive force-temperature relations reflect the entropy of mixing of zinc and, therefore, the occurrence of a discontinuity marks the transition between two different equilibrium situations involving the solution of zinc. A number of other investigators3-5 have used such observations to determine liquidus boundaries in binary alloys. Since the upper portions of the ternary electromotive force-temperature relations of this study had the same slopes as the binary alloys, the discontinuities are interpreted as marking the transition between the single-phase liquid region and the underlying two- and three-phase regions. Reference to the Zn-Bi equilibrium diagram6 confirms that the binary alloys were single-phase liquids at the experimental temperatures. Fig. I shows the electromotive force-temperature relations for the alloys containing Bi-Zn-Au and Fig. 2 shows similar relations for the Bi-Zn-Cu alloys. In the lower portion of each figure, the temperature of the discontinuity is plotted vs the mole fraction of the added solute at the various levels of zinc concentra- tion. Cross-plots from these curves at constant temperature permitted the construction of the partial liquidus surface isotherms shown in Figs. 3 and 4.

Jan 1, 1967

By V Kveldsvik, N Ragvin, T Eiken, G Grøneng, G V. Ganerød

Catastrophic rock slope failures have caused destructive tsunamis in Norwegian fjords. At the Åknes rock slope the tsunami generating potential is large due to the potential large volume involved in a possible catastrophic failure. Widening of the upper crack has been recorded since 1986, and in recent years, a quite extensive investigation and monitorin campaign has been conducted. Data from some of these investigations are presented and analysed with respect to a preliminary evaluation of the stability of the slope.

Jan 1, 2006

By Holmes R. J, Miles J. G

An on-stream shale detector has been developed that is suitable for use on conveyor belts carrying iron ore of up to 200 mm particle size. The shale is distinguished from high-grade iron ore by means of the substantially greater total natural gamma-ray activity (400-3000 keV) of the shale, which is due to the presence of uranium (214Bi), thorium (208TI) and potassium (40K). Other gangue materials, sueh as highly siliceous cherts and jaspilites, escape detection because of their low activity. A dynamic trial of the shale detector at Mt Whaleback, using a large-volume (100 × 100 400 mm long) "Polyscin" Nal(TI) gamma-ray detector, demonstrated that as little as 20 tonne of ore on a conveyor belt (equivalent to partial truckloads of ore) can readily be monitored for shale content.

Jan 1, 1981

By I M. Platten, Y Xie

Complex gold deposits are generally characterised by variable geometries, strong structural controls on grade distribution and a high-nugget effect. The use of diamond drilling and fire assays in this environment often results in an understatement of grade. Bulk samples are likely to be the closest estimators of true grade, and may be required to evaluate geological/grade risk during resource estimation/feasibility studies. Any bulk sampling program requires appropriate planning and implementation. The planning stage should attempt to delimit the extent and nature of mineralisation; characterise mineralogy and metallurgical properties of the ore; and define bulk sample size and how it will be sampled/processed. The approach to sample processing will be governed by the results of metallurgical testing and geological knowledge. Careful design of sampling protocols must be undertaken through material characterisation, understanding of gold particle sizing and the application of GyÆs Sampling Theory.

Jan 1, 2008

By Christopher M. St. John, Tony F. Zahrah

Empirical and numerical methods are the two extremes of the tools available for the seismic design of subsurface excavations and underground structures. Both have their limitations: when relying on purely empirical methods directly relevant experience may be scant; site data may be insufficient to justify a comprehensive dynamic analysis. The primary purpose of this paper is to review the analytical tools available to the design engineer of subsurface excavations and underground structures. Particular attention is devoted to simplifed models that appear to be applicable in many practical cases.

Jan 1, 1985

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence events induced by underground longwall coal mining operations can cause various disturbances to surface structures ranging from integrity and stability to functionality problems. Highway bridges, as a kind of special road construction that can only tolerate smaller movements and deformations than road pavements, are particularly susceptible to severe influence caused by subsidence-induced ground movements and deformations. However, based on accurate subsidence prediction and correct influence assessments, efficient and effective mitigation and remediation measures can be designed and implemented to ensure the continuous service of bridges, safety of the travelers and smooth mining operations. In this paper, based on the predicted final and dynamic surface movements and deformations, the techniques to assess subsidence influence on the integrity, stability and functionality of bridge structures (e.g., decks, beams, abutments, etc.) are presented. A number of mitigation measures to protect the bridge structures are recommended along with an actual application case.

By Sumner M. Anderson

Any discussion of outside support to Latin American mineral industries must concede at once the pre-eminent role of U. S. industry and business. American capital has developed the great copper resources of Chile and Peru, the lead-zinc of Peru and Mexico, the bauxite of Surinam and Jamaica, the petroleum and iron ore of Venezuela. American consumers have provided the market for their products. U. S. companies operating south of the border have trained Latin American geologists, engineers, chemists, and skilled labor—including metal, mineral, and fuel technicians—to new and greater competence. The industrial demands of World War II drastically altered world economics and concepts of U. S. foreign mineral requirements. In this country discovery of vital mineral resources fell far behind the alarming depletion rates, and there was new appreciation of the actual and potential importance of the world's less extensively explored areas. During the war and afterward, the task of supplying the nation's mineral requirements became greater than private industry could carry alone, and the Government assumed a position of continuing support. In Latin America, as elsewhere, this support applies in three categories: banking, procurement, and technical assistance. The first two are now generally accepted as necessary Government functions; the third has often been misunderstood and misinterpreted, although it has given rise to legitimate controversy. There have been major accomplishments in all three categories, as well as some errors of judgment. Since the beginning of World War 11, U. S. Government financing, procurement, and technical assistance have been applied on a large scale to a wide range of commodities and services throughout the free world. The present discussion—under the separate headings mentioned—will concern only the support related to a single industrial group in a single geographic area. During the War Federal banking was conducted on an emergency scale by temporary agencies created to meet the abnormal circumstances. Unfortunately, there are no readily available data on these activities that would permit evaluating loans and credits extended for mineral projects in Latin America. The only agency operating in this field since World War II is the Export-Import Bank, under its own authority and to some extent from credits authorized by the Office of Defense Mobilization. The Bank can offer more capital—on more favorable terms—than is available from most Latin American banks, and its staff of engineers evidently can appraise loan applications more favorably than commercial banks in this country are willing to do. The risks seem to be justified, as defaults have been well under 1 pct of total loans. From V-J day 1945 to the end of 1957, mineral loans to Latin America have been authorized for projects totaling $541.63 million in eight countries. In order of magnitude of credits, they have been made to Brazil, Peru, Chile, Mexico, Argentina, Venezuela, Guatemala, and Bolivia. In order of magnitude by industries. they are for development and expansion of steel mills, copper, manganese, nitrate plants, iron ore, zinc plants, sulfur plants, cement plants, tungsten, coal, and lead. Loan Distribution: By far the largest loans have been $307.9 million for iron and steel projects in Brazil, Chile, Mexico, Argentina, and Peru: $100.4 for developing the great low-grade copper deposits of southern Peru; and $55.3 million for developing manganese deposits in the Territory of Amapa, Brazil. Others range from $20.8 million for a zinc smelter in central Peru to $19 thousand for iron-mine trucking equipment in Chile. It has been noted that 59 pct of the loans have been to foreign companies, 14 pct to companies of mixed foreign and American capital, and 27 pct to American mining companies. About 40 pct of the total authorizations has been disbursed so far. In addition to these amounts, the Strategic Materials Division of the Economic Cooperation Admin-

Jan 1, 1959

By Katsuyoshi Kondoh

The utilization of silica particles originated in rice husks as reinforcements of magnesium composites was discussed. By using the solid state reaction of rice husk silica particles with magnesium powder, P/M magnesium based composites dispersed with the magnesium silicide (Mg2Si) and magnesium oxide (MgO) were fabricated. High-purity silica particles were originated from rice husks, one of the major agricultural wastes, via the citric acid leaching treatment and combustion in air. The effects of the silica particle characteristics such as size, crystalline and porous structures, on the reactivity of silica and magnesium to synthesize Mg2Si intermetallic were discussed. Amorphous silica was more useful for this reaction than crystalline one. The reactivity of rice husk silica was superior to that of the conventional mineral silica particles because of not only its amorphous structure but the larger specific surface area due to their pore structures. In the case of the green compact of the mixture of the rice husk silica and Mg powder, the silica particle size was not effective on the reactivity because the coarse particles were fractured into fine ones by cold compaction. The distribution of Mg2Si intermetallics of magnesium powder composites consolidated by SPS process was investigated by XRD and SEM-EDS analysis. Their mechanical and physical properties were also evaluated in detail.

Jan 1, 2009