Search Documents

By Paul Hatmaker

This paper covers briefly the particular field of dolomite and magnesium limestone; certain uses of high-calcium limestone are mentioned only to show more clearly the limita¬ tions of the magnesian rocks. Such a comparison is helpful because magnesium carbonate is essential for some uses; for others it is immaterial; and for many its presence in an appreciable amount is objectionable. Magnesium carbonate, occurring as a rock resembling limestone or dolomite, is described in United States Bureau of Mines Information Circular 6437, Magnesite. Other com¬ pounds of magnesium are described in United States Bureau of Mines Information Circular 6406, Magnesium Compounds (Other Than Magnesite). Limestone, geologically, is a rock composed essentially of calcium carbonate; commercially, however, the term may include dolomite and magnesium limestone.

Sep 1, 1931

By J. J. Taute, S. J. Archer

"BASF Mining Solutions has developed a new-generation copper solvent extraction reagent that offers significant benefits over standard extractants currently available to the industry. As the name suggests, the new hightemperature (HT) extractant can be used at a higher operating temperature, but also exhibits significantly lower degradation rates, greater copper-toiron selectivity, and is totally nitration-proof compared with the standard extractants. Pilot-plant trials have also shown that lower aqueous-inorganic entrainment can be achieved. This paper investigates the technoeconomic benefit of using the HT extractant as an alternative to the standard extractant in a high-temperature application. The results of the technical evaluation showed that the use of the HT extractant reduces the extractant addition requirements and bleed volume from copper electrowinning; this smaller bleed requirement further reduces acid and limestone consumption, leading to a reduction in valuable metal losses. The results of the economic evaluation showed that the use of the HT extractant represents significant cost savings over that of the standard extractant. IntroductionCurrent solvent extraction (SX) reagents employed for the extraction of copper from typical pregnant leach solutions (PLS) at ambient conditions function well with minimal long-term effects on the extractant’s performance (Taute et al., 2015). This performance, however, deteriorates at elevated temperatures due to the degradation of the reagent’s hydroxyoximes. The degradation mechanism, acid-catalysed hydrolysis of the oxime, is accelerated by high temperature. This has a knock-on effect where the increase in degradation products increases the organic viscosity, leading to increased entrainment, crud formation, and ultimately to an increase in SX reagent consumption (Bender, Emmerich, and Nisbett, 2013).SX reagents also show an increase in the co-extraction of iron as the ferric concentration in the PLS increases. Co-extracted iron is transferred to electrowinning (EW) during stripping of the loaded organic and can adversely affect EW current efficiency. Iron in the EW circuit is typically managed by bleeding the electrolyte; however, this can lead to excessive consumption of EW reagents such as acid, cobalt, and mist-eliminating surfactants. The electrolyte bleed can also affect upstream consumption of reagents, such as lime, due to the high acid concentration recycled to leach."

Nov 1, 2018

The changes in layout and design over 48 years, from the first crushing and shiploading plant installed at Whyalla in 1915, up to the present plant being built at Koolan Island, Yampi Sound may be summarized as follows.1. Smaller motors and lower power consumption have resulted froma. oil lubrication, where practicable, in place of grease,b. a high pressure "oil-lift" device to reduce starting torque in crushers with white metal bearings, andc. roller bearings in place of white metal.2. Short centre drives with pivot-based motors permit controlled loads on bearings and a reduction in size of crusher houses and motor rooms.3. Dust proofing and pressurising of crusher houses and motor rooms reduces working temperatures and improves cleanliness.4. Variable speed pan feeders give improved plant control, with the use of one man only, and remove the need for large surge bins between crushing stages.5. The use of diesel quarry trucks to dump ore through a "drive over"tip results in faster truck cycles.6. Elevated cylindrical silos with air operated chutes, replace long horizontal storage bins with multiple manually operated side discharge chutes for loading rail cars, and give faster and more accurate truck loading. The silos are charged by belt conveyors with automatic distributors.7. Increased shipping bin capacity (40,000 tons at Whyalla and 6O,OOO tons being built at Koolan Island) caters for the bigger vessels now in use and envisaged for the future. Automatic travelling distributors deliver ore to the bins in layers to ensure, maximum mixing and a more uniform grade for blast furnaces.INTRODUCTIONThe Broken Hill Proprietary Company Ltd has six major crushing plants in Australia at its principal sources of raw material. These are at Iron Knob bench G, Iron Knob scree ore plant, Iron Baron, and Cockatoo Island, all of which are ironstone operations. The other two plants are at Rapid Bay, a limestone quarry, and at Ardrossan, which is the Company's only source of dolomite.

Jan 1, 1963

Editor?s note: Each year, the June issue of Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue. Thank you to the industrial minerals annual review editor, to the technical committees chair and vice-chair, and to the authors of the individual commodity profiles. Jim Norman, member SME, of GeoTrans, Inc., is the industrial minerals annual review editor. SA Ravishankar, member SME, of Cytec Industries, is chair of the industrial minerals technical committees. Technical committee vice chairs include: ? Abani Samal, member SME, of Pincock Allen & Holt, agricultural minerals. ? Aaron McMahon member SME, of Pincock, Allen & Holt, ceramics and refractories. ? Bradley S. Van Gosen, member SME, of the U.S. Geological Survey, chemical raw materials. ? Mark Zdunczyk, member SME, of Continental Placer, Inc., construction materials. ? Jerry Gauntt, member SME, of JEG Minerals Consultants, fillers and pigments. ? Michael Cheshire, member SME, of Indiana University, sorbents, filters and process aids. Their help makes possible this June industrial minerals issue. On behalf of ME readers, the editors thank them.

Jan 1, 2008

By K. T. Menzies

Over 1500 literature citations related to diesel exhaust sampling and analysis were obtained as a result of both computer and manual searches of nine data bases. Abstracts and hard copies of relevant citations were reviewed and those considered appropriate for evaluation were included in a bibliography. Based on the literature collected, available sampling and analysis methods for the following diesel exhaust contaminants were evaluated: CO, CO2, NO, NO2, Hydrocarbons, Particulates, PNA, S04, Oxygenates Emphasis was given to both laboratory and field methods for these species. Methods were evaluated on the basis of sensitivity, selectivity, accuracy and reliability and a selected list of preferred methods was developed for each compound/ class. The selected methods were additionally evaluated through communication with current investigators. Sampling and analysis methods for all compounds except CO and CO2 were observed to have some unreliability. Recommendations were made for future research to develop, improve, and validate methods.

Jan 1, 1979

Advances in technology have led to larger and deeper open pit mines and, consequently, also increased the potential economic impact associated with slope failures. If the ultimate aim of mining operations is to maximise project profit, it is surprising to see related research activities have mostly been focusing on technical areas such as slope stability modelling, but with limited studies conducted to date to assess the relationship between geotechnical uncertainties and economic risk. Given most major decisions in the mining industry nowadays are made by management staff with financial background, any design approach that would help to link slope stability analysis results with monetary values would no doubt enhance communication between geotechnical practitioners and decision makers. This paper presents a study which assesses economic impact of slope failures to assist in mine planning. The study also estimates the impact of slope failures on project value, which would enable economic risks associated with pit slope designs to be closely examined. The proposed risk assessment techniques, used by financial institutions for many years to assess portfolio risks, can assist geotechnical practitioners in quantifying risks of slope failures. Risk-adjusted concepts are also suggested to assist management in selecting a slope design with optimal risk and return ratio.

May 1, 2010

By Satyam Tiwari, Sarat Kumar Das

Tailings from mines and industries impose danger to the environment as evidenced by the recent failures of tailing storage dams. The tailings are mostly non-plastic with silt-size particles, but their behavior is largely dependent on the extreme void ratios of the material. Hence, the critical state provides an appropriate perspective in explaining the behavior of these geomaterials. Based on a comprehensive dataset of non-plastic tailings and non-plastic soils, an attempt has been made here to correlate critical state parameters to extreme void ratios and stress parameters. A hybrid algorithm with multi-objective feature selection (MOFS) and extreme learning machine (ELM) was used to establish the correlation and to identify the most influential input parameters. Based on the information from the proposed hybrid algorithm, a comprehensive prediction model is proposed using multi-gene genetic programming (MGGP) algorithm to facilitate quick estimation of critical state parameters. The performance of both models has been assessed using several performance metrics. The results from the study indicate that hybrid MOFS algorithms perform very well in the prediction of critical state line parameters and the identification of influential features. The findings of the study have significant implications for future research on the safe management of tailing storage facilities.

Dec 22, 2023

By Philip C. Tully

This bibliography contains 3,062 different citations to technical and scientific literature about helium and alpha-particles abstracted by 13 abstract service publications during 1963. Multiple subject classification has increased the total number of entries to almost 5,000. Helium citations are listed by 23 major classifications. The number of subclassifications has been greatly increased to minimize the time required for literature search. The use of automatic data processing has been extended in compiling the bibliography.

Jan 1, 1970

By G. Asai

The purpose of this Bureau of Mines investigation was to determine the properties of arc-melted iron-chromium alloys ranging in chromium content from 12 to 50 wt.-pct. Alloys were prepared by consumable-electrode arc melting of electrodes composed of high-purity chromium and high-purity iron. Alloys were fabricated to rod and sheet, and the following data were obtained: Electrical resistivity, hardness, tensile strength, and impact strength at room temperature; and creep-rupture life at 650° C. (1,200° F.). As the chromium content of the annealed alloys varied from 12 to 50 pct., the properties varied as follows: The electrical resistivity increased proportionally from 41 to 53 microhm-cm,; the Rockwell hardness varied from A 38 to A 58; the tensile strength ranged from 52,000 to 96,000 p.s.i.; the impact strength of V-notched charpy specimens varied from 140 to 405 ft.-lb., and the 100-hour creep rupture life at 1,200° F. varied from 5,000 to 16,000 p.s.i.

Jan 1, 1962

By Aaron S. Bradshaw, Ryan M. Coulson

The offshore wind industry in the United States is slowly emerging with the recent construction of the first offshore wind farm located off the coast of Rhode Island. The turbines at the Block Island wind farm are supported by piled jacket structures, which historically have been used for much heavier oil and gas platforms. Offshore wind turbines have unique design requirements and the axial behavior of the supporting piles under cyclic loading is important to design. Cyclic degradation along the pile shaft can affect the capacity, deformation, and stiffness performance of the foundation and of the structure as a whole. This paper proposes a strain-based approach to estimate the fatigue (or endurance) limit of a cyclically loaded pile that may be applicable to long-term service loading. The method is applied to an existing load test dataset and the analysis results appear consistent with the observed pile response. INTRODUCTION The demand for renewable energy has been increasing in recent decades and wind power has seen a dramatic increase in popularity. In Europe, as of 2017 there were 4,149 grid-connected offshore wind turbines across 11 countries (windeurope.org), many of which are supported on monopile foundations. It wasn’t until recently (2016) that the first offshore wind farm was constructed in the United States off the coast of Block Island, Rhode Island. The project included 5 piled jacket structures founded in terminal moraine deposits. Future offshore wind development along the U.S. eastern seaboard could possibly utilize jacket structures in granular foundation soils. Loads from wave, wind, and turbine rotation induce cyclic loads on the foundation that have on the order of 108 loading cycles over the service life on the structure (Schneider and Senders 2010). Turbines located along the U.S. east coast have the added risk of hurricanes. As shown in Figure 1a, the lateral loads on a jacket structure are transferred primarily as axial compressive and possibly tensile loads on the supporting piles depending on the weight of the structure. The friction along the shaft of the pile can be prone to cyclic degradation, leading to reduced pile capacity and stiffness, and increased deformations. An offshore wind turbine foundation must be designed for a variety of limit states including ultimate, serviceability, and fatigue limit states. For a jacket structure this would include an analysis of the ultimate axial pile capacity, axial stiffness, and axial deformations, all of which can be affected by cyclic loading both under extreme (i.e. storm) conditions as well as long-term service conditions. Axial pile stiffness is needed, for example, to estimate the natural frequencies of the structure as a whole and to assess dynamic and fatigue loads. The structure must be designed such that its natural frequency remains outside the loading frequencies of the waves and turbine blade passing frequencies to avoid resonance. Therefore, prediction of the axial response of the piles is important to the design of these structures.

Jan 1, 2018

By Louis A. Panek

An improved centrifugal-testing apparatus has been designed and built in the Bureau of Mines laboratory at College Park, Md., which is unique in that it incorporates the use of resistance gages to measure directly the strains in a rotating model without testing it to failure. Owing to this feature, a more rapid testing method can be used; furthermore, model materials need not be restricted to those of the prototype. The behavior of any structure in which strains of significant magnitude are produced by its own weight may be studied in a small model subjected to simulated gravity loading. The model is rotated in a centrifuge to induce in it centrifugal forces, which, like the gravitational forces in the full-size structure, act on the volume elements and are proportional to the masses thereof. Centrifugal testing is, therefore, applicable to the design of mine openings and to the study of similar ground-control problems. It constitutes an experimental method for determining the state of strain in a structure for which analytical methods are excessively laborious or even impossible. In previous applications of centrifugal testing by other investigators, the models usually were tested to failure, and the analysis was made from-the type of break produced. The models were made of the same materials as the proto-type, and the test results were applied only to the particular prototype represented by the model. Beam deflections were measured from photographs of the rotating model, but no means was employed either to determine the actual distribution of stress in the model or to determine quantitatively the degree of restraint imposed on the ends of the loaded model beam, that is, to determine whether the loaded model behaved as a beam with rigidly fixed ends or as some other type of beam. With the apparatus described, it is possible to determine the state of strain, and thus the boundary conditions, in a rotating test model weighing up to 90 lb., which can be subjected to centrifugal forces up to about 2,600 times the force of gravity. The load-strain relationship, applicable directly to the prototype, can be determined from a Single model test. The test results can be presented as quantitative relations between the loads, strains, and dimensions and mechanical proper-ties of the structural members and can be applied to any prototype, whatever its component materials, that satisfies the similarity requirements.

Jan 1, 1952

By Adrian Daniel

"Dating back to 1934, Con Mine is located directly south to the city of Yellowknife in the NWT, Canada. With mill operations ceasing in 2004, a challenging surface remediation situation resulted which required the treatment of close to 40,000 m3 of Arsenic impacted material.Through much of the period of 1941 to 1970, Con Mine treated their refractory arsenopyrite ore through the use of an Edwards Heath roaster. With mounting environmental pressure and through Canadian governmental studies during 1950 to 1970, attention was directed to the Arsenic Trioxide material being collected by two Doyle scrubbers on the Con’s roaster stack. In 1970, the roaster was decommissioned leaving the resulting Arsenic material in two containment areas on surface.As a result of Con Mine entering into remediation in 2004, the Con’s autoclave, commissioned in 1992, was dedicated to the immobilization of high impacted Arsenic material through the combination of excess Iron under high temperature and oxygen overpressure. Examined, herein, is the history and chemistry of the Con Mine autoclave as well as the two stages of chemistry for the Water Treatment Plant used to remove arsenic, heavy metals and WAD cyanide from tailings water. Simplified capping plans of the tailing containment areas and a high arsenic impacted area are also presented.INTRODUCTION TO CON MINECon Mine (Con) is situated just south of the City of Yellowknife in the North West Territories (NWT) Canada and is bounded locally by Yellowknife Bay (North Extension of Great Slave Lake) to the east and Kam Lake to the west (Figure 6). The discovery of gold at Con was made in 1934 and mineral rights were acquired by Consolidated Mining and Smelting Limited (Cominco) and Falconbridge soon thereafter. Nerco Minerals Limited (Nerco) took control in 1986 and in 1993, was subsequently sold to, Miramar Mining Corporation which in turn was purchased by friendly takeover involving Newmont Mining in November 2007 as a result of acquiring the Miramar’s Hope Bay project. Con’s underground operations ceased in September 2003 and have since entered into the remediation of the site. The current surface lease holdings are about 340 Hectares (Table 1) which sits on top of the Archean-aged Yellowknife Greenstone Belt."

Jan 1, 2009

By D Thomas

Geochemical data related to AMD for the West Coast and Southland regions have been collated into a relational database and GIS system. The types of information include; rock geochemical data, water chemistry data and aquatic macro-invertebrate abundance data. This information will be combined with eco-toxicology experiments to determine impact thresholds on aquatic ecosystems. Ultimately these datasets will be combined with remediation investigations to produce a Framework to assist decision making related to mine planning, consent and compliance.   Current geochemical research examines the controls on As concentrations downstream of gold mining areas and the variability of AMD from Brunner Coal Measure rocks. Assessment of factors that control the chemistry of Brunner Coal Measure AMD such as mine type, hydrogeology, geology, geochemistry and climate is in progress. Minerals that control the concentration of aluminium downstream of AMD point sources include alunite, jurbanite and various forms of Al(OH)3.

Jan 1, 2005

The United States has not begun commercial operations to tap its largest poten-tial sources of oil supply - oil shale and coal. The reason is that domestic petrol-eum has been plentiful in the past and liquid products probably could be produced from it at the lowest cost. In view of the ever-increasing need for petroleum in the United States, the critical international situation threatening foreign supplies, the growing demands for steel, and the heavy costs to industry of constantly discovering and developing new oil fields, it is believed that the prompt development of a synthetic fuel industry based on oil shale and coal is not only requisite to safeguard our oil supply but is an economically sound course for the foreseeable future. To neglect its development is to close our eyes and minds to our own resources at a time when they are needed critically. It also is apparent now that neither the Government nor industry would be taking any considerable economic risk in starting the initial plants, especially as measured against their potential value in meeting critical oil and chemical demands and in building a new industry in the West.

Jan 1, 1951

By W. P. Tassie

"The location of Quintette Coal Limited's pit and geologic nature of the dedicated reserves combine to introduce a number of factors which can adversely affect waste dump stability. These factors include steep terrain, variable material type and particle size, and precipitation. This paper describes the solutions to related waste dump problems. A brief geotechnical review of the waste dumps is given and Quintette's operational strategies during periods of dump stability and instability are discussed. Despite best efforts, failures occasionally occur and discussion is included on Quintette's success at bringing failed dumps safely back into use. IntroductionQuintette Coal Limited (QCL) property is situated on the east slope of the Rocky Mountains near Tumbler Ridge, approximately 120 km southwest of Dawson Creek, British Columbia. This surface mine is located on mountainous terrain and is subject to climatic extremes of wind, precipitation and temperature.QCL has a current annual production of 4.75 million tonnes of metallurgical coal with a stripping ratio of 7: 1. This correctly implies the extraction of over 33 million bank cubic metres (BCM) of waste which is placed on numerous waste dumps at various locations adjacent to the pit.There are three active pits - Mesa, Wolverine, and Shikano (Fig. 1). Shikano is a newly developed pit located near the plant site. It is not subject to the unique dump management problems prevalent at the Mesa and Wolverine pits, therefore the Shikano waste dumps will not be discussed . The dumps for the Mesa and Wolverine pits, however, have been technically and operationally challenging since shortly after mining began in 1983. Their characteristics, associated site specifics and management, therefore, are the subject of this paper.Waste dump locations for the Mesa and Wolverine pits are shown in Figures 2 and 3 as is the relative waste distribution . Each sub-pit is connected to a principal waste dump in reasonable proximity and to an alternate dump should disposal of waste be necessary at that location. The waste dumps are constructed from the top elevations initially to coincide with subpit development. In the initial years (1-7) waste dump heights will be up to 250 m, then, as the mine matures (8-20 years), waste dump maximum heights will continuously decrease to coincide with lower bench elevations"

Jan 1, 1988

By Alessandro Navarra, Joël P. T. Kapusta

"The converting cost modeling software introduced by Ng et al. in 2005 [1] has been extended to consider the reprocessing of reverts and copper scrap. The original model evaluated the operational costs of a Peirce-Smith converter; algebraic relationships had been implemented with arrays (to represent matrices, vectors and scalar ratios). The new software brings flexibility to the underlying thermochemical balances, by using linked-lists instead of arrays. It is now possible to consider the blending of several feeds, including reverts and scrap.The software computes the length of the converting cycle from the Fe and S content of the charge together with the blowing rate; the times required for other operations (charging, skimming and idle time) are also accounted for. The costs of consumables such as flux, fuel, oxygen or compressed air are all evaluated. Downtime, labor, and materials for converter lining repairs are also considered. The software is easily extended to examine the costs of alternative operating strategies or injection technologies such as sonic single pipe injection and sonic shrouded injection. The potential cost benefits of alternative operating procedures and technologies are discussed through example calculations."

Jan 1, 2009

By Margaret R. Egan

A series of experiments were undertaken by the Bureau of Mines to determine the emission products of several types of conveyor belting and other combustible materials found in mines. These experiments were conducted under intermediate-scale, simulated mine conditions to determine smoke characteristics and gas concentrations. From these determinations, heat-release rates, particle sizes, obscuration rates, combustion yields, and production constants were calculated. Three types of belts were investigated: chloroprene, also known as neoprene (NP); polyvinyl chloride (PVC); and styrene-butadiene rubber (SBR). The belts were designated as ignitable or self-extinguishing depending on the length of the burning time and the subsequent combustion products. Under these experimental conditions, the SBR belts were the easiest to ignite. The PVC and NP belts tended to self- extinguish within a few minutes after ignition, but were still capable of maintaining a brief flaming period. These conveyor belt combustion results are compared with previous analyses of wood, transformer fluid, and coal fires. Together they form a data base by which findings from future experiments with other mine combustibles can be compared.

Jan 1, 1988

The plant and processing site at Porgera has been built on a levelled mudstone ridge about lkm E of the mine. Excavation of 7xl06m3 of soil and rock was necessary to achieve the required area. The exposed mudstone belongs to the Chico Formation and is weak, sheared and readily breaks down by slaking upon exposure. Tectonic uplift and subsequent erosion have produced the present landscape of narrow bedrock ridges, with deep colluvium in the incised valleys. The deep excavation to a maximum of 60m, has rapidly unloaded the mudstone, and subsequent stress relief has caused rebound and dilation of the material. The processes of pore pressure equilibration, softening, progressive failure and loosening, combine to deteriorate the newly exposed rock mass. These processes are commonly associated with pre-existing shear surfaces, fissures and a

Jan 1, 1991

By G. R. Fitterer

In the manufacture of steel by any process the refining period involves the partial elimination of the metalloids carbon, manganese, phosphorus, and silicon, by virtue of their reactions with ferrous oxide. At the end of this refining stage the metal consists chiefly of iron in which small amounts of these materials are dissolved. Unless some deoxidizer is added to the steel at this time, the reaction between carbon and ferrous oxide will continue with such force that it is impossible to form sound steal in the ingot molds. Instead, the product will exhibit a marked porosity due to the formation and trapping of carbon monoxide-the product of the reaction mentioned. However, if deoxidizers are added, steel may be obtained which is dense and free from gas bubbles. At the same time the deoxidation products will remain in the steal as impurities. For example, silicon additions form Si02 or combinations of Si02 and FeO. Additions of manganese form deoxidation products consisting of various proportions of MnO and FeO. It is also quite obvious that simultaneous additions of manganese and silicon will form oxide combinations either in the binary system MnO-SiO2 or in the ternary system FeO-MnO-SiO2. Work at the Pittsburgh Experiment Station of the United States Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board, involved the study of such deoxidizing reactions and their products. In this connection considerable information is necessary concerning FeO, MeO, Si02, and Al 203, and their various combinations. Some of the most needed data are the melting points of all of these materials. At the outset of this work ordinary methods of melting point determinations were found to be inadequate for various reasons, and the procedure finally selected involved the use of the micropyrometer with occasional corroboration by quenching methods, The reasons for this selection, together with a description of the apparatus, are given in the following pages.

Jan 1, 1932

By Paikowsky, Samuel G.

"Due to the way drilled deep foundations are being constructed, their structural integrity and geotechnical capacity are highly variable. Drop weight systems are increasingly being used to dynamically test the capacity and integrity of drilled deep foundations. Conventional pile driving hammers are often either inadequate or not economical to test these foundations and drop weight systems have therefore been developed to allow for dynamic testing.The advantages of the tests include high mobility, short testing time, low cost relative to static load tests (allowing multiple tests at a single site), and integrity/construction quality evaluation concurrent with capacity determination. The dynamic testing method for drilled deep foundations encounter several difficulties including: the need for a pre-testing analysis for matching pile, soil and testing system, adequate mass and drop height to reflect the mobilized capacity without structural damage, test interpretations for irregularly shaped and/or non-uniform piles, need for reliable dynamic measurements depending on the impact and the distance between the impact and the measuring point, and limited knowledge about the accuracy of the predictions.The principles of the tests are presented using simplified models and demonstrated via a case history. Drop weight systems are reviewed. Dynamic measurement principles are explained and the construction and testing quality effects are outlined and demonstrated via numerical modeling and case histories. A comparison of dynamic and static tests is presented via a database, case histories and finally a short review of relevant codes is provided.1 IntroductionTraditional static axial load test is performed by a slow application of a force produced against independent reaction, imitating structural loading. It is the most reliable method to determine the pile’s performance as commonly required under typical service conditions. The major limitations of this testing are: (i) high cost associated with set-up, test duration, interpretation and construction delays, and (ii) inability to obtain information about the pile-soil interaction along the pile without additional testing means (e.g. tell tales, strain gauges, etc.). These limitations are acute when high capacity foundations are involved."

Jan 1, 2015