Search Documents

By Haiping Sun, Samir Ganguly, Oleg Ostrovski, M. Yaser Lone

Wettability of graphite by synthetic SiO2-Al2O3-CaO-MnO slags with varied MnO content and by industrial slags was studied at 1350-1600 °C using sessile drop method under argon atmosphere. Initial contact angle was the lowest (110-115o) for the MnO-free slag. For slags with 10-40 wt% MnO, the initial contact angle was in the range 125-135o. The contact angle decreased with the contact time. The change in the contact angle with slag mass was found insignificant. The surface tension of slags obtained from the drop shape analyses was 500-800 mN/m and varied in a narrow range with temperature and MnO concentration. The reduction rate increased with increasing MnO content in the synthetic slag from 20 wt% to 40wt% and temperature. Increasing temperature also increased the rate of reduction. No correlation was observed between the reduction rate and MnO content in the synthetic slags in the range 0-20 wt% and in the industrial slags. The rate of SiO2 reduction from the molten slag was close to the rate of MnO reduction. The MnO-free slag had the largest contact area with graphite substrate. Keywords: reduction, wettability, graphite, slag, manganese, surface tension.

Jan 1, 2007

By Gabriel S. Esterhuizen, Anthony T. Iannacchione

The roof rock in underground limestone mines in Northern Appalachia can be subject to high horizontal stresses in spite of the shallow depth of the workings. The high stresses can cause roof stability problems. The National Institute for Occupational Safety and Health staff have observed a distinctive asymmetrical mode of failure at the pillar-roof contact in two underground stone mines, which is different from the typical failure mode observed in response to excessive levels of horizontal stress. A dip of greater than 5° was identified as a possible cause of this mode of failure. Numerical model experiments showed that an increase in the dip of the workings can cause an increase in the stress at the up-dip corner of the roof beam. A case study is presented in which failure at the pillar-roof contact was observed where the dip of the workings was 7° in a high horizontal stress field. Numerical modeling showed that the relatively small dip of the workings could have induced stresses changes in the immediate roof that would explain the failures. The model results also showed that this mode of failure is less likely to occur if the limestone pillars contain weak bedding planes that provide stress relief. In addition, the results showed that for the conditions at the case study site, the stress in the roof beam was not sensitive to the thickness of the roof beam or to the excavation span. The high horizontal stresses at this site are an important contributing factor to the observed failures.

By Peter J. Nicholson

A new method of constructing retaining walls, in-situ, prior to excavation has been developed. This "Vertical Earth Reinforcement Technique" VERT, has been demonstrated at a full scale test wall at the National Geotechnical Experimentation Site at Texas A&M University. This 10 meter high wall, was constructed of elements of soil mixing in an array that forced composite behavior between the soil mixed elements and the in-situ soils. Inclinometers and extensometers were used to verify the performance of the wall. The construction and results of the testing are presented.

Jan 1, 1998

Performance of Dry Separation Processes in Cenospheres Recovery from Coal Fly Ash

Sep 13, 2010

By J. de Villiers

Through the application of the Rietveld method, X-ray diffraction analysis has developed into a fully quantitative method for phase analysis. The Rietveld method itself has progressed from an unstable method that required constant operator intervention to a stable and robust method suited even for routine analysis. The method, however, requires a good initial calibration and periodic checks on its precision and accuracy. Several examples from minerals processing, pyrometallurgy, and materials science show the strengths and applicability of the method. The limitations and sources of error are also discussed.

Jan 1, 2007

By Steven Norris, William Moler, Michael Cole, Patrick Doig, Debi Lewis, Craig Pyle, Matthew Crow

The recently completed Lower Northwest Interceptor Program (LNWI) in Sacramento, California comprises, ten pairs of micro tunnels totaling 4,369 m (14,417 ft),three horizontal directionally drilled bores totaling 956 m (3,154 ft), and two large diameter tunnels under the Sacramento River totaling 1,198 m (3,953 ft). This paper briefly summarizes surface and subsurface conditions, and planning and design considerations. It then goes on to describe problems encounterd with each trenchless crossing, as well as lessons learned with respect to shaft construction, ground control at shafts during tunnel break-in and break-out, frac-out and heave, settlement, obstructions, coordination with permitting agencies, and application of geotechnical baseline reports.

Jan 1, 2007

Geometallurgical Study of Copper Oxide Mineralisation Hosted in Gravels of Different Physical Quality

Sep 13, 2010

By W. A. Heitbrink, J. D. Ashley, R. E. Gresh, J. A. Organiscak, A. B. Cecala

Many different types of mobile equipment used in surface coal mining utilize enclosed cabs to protect equipment operators. The overburden removal process is extremely dusty and can cause excessive exposure to respirable dust, especially crystalline silica. After equipment is used for years, many components of the enclosure deteriorate and its effectiveness is greatly reduced. This report discusses a cooperative research study performed on an Ingersoll Rand DM45E surface drill, retrofitted with a new Sigma pressurization and filtration system. Respirable dust concentrations were substantially reduced from 0.64 mg/m3 during pre-testing to 0.05 mg/m3 during post-testing with the new system, representing a 92% reduction in dust levels in the drill cab. This new system appears to be a very well-built and sturdy device, well-suited for the mining industry.

Jan 1, 2002

By G. S. Harper

Noise in general and drilling noise in particular have received increasing attention within the South African mining industry during the last 10?15 years. The Mine Health and Safety Committee1, during their 2003 annual summit, established two significant milestones to be met by December 2008 and December 2013. The 2008 milestone target is that of no more than ten per cent deterioration in hearing among occupationally exposed individuals, whereas the 2013 milestone target is that of less than 110 dB sound pressure levels at any place in the workplace. While these targets relate to general noise within the mining industry, it is widely believed that the most significant source of noise contributing to noise induced hearing loss (NIHL) among the underground workforce, is that of pneumatic rock drills. Data pertaining to the noise emission level of any machine is generally reported as either a sound pressure level or a sound power level of a single machine measured under free field conditions as defined in Appendix 3 of SABS-ISO 37442. However, rock drills are seldom used in isolation and underground conditions cannot be considered as free field. A methodology for the selection of rock drills on the basis of total operating cost has been developed. However, this paper focuses on the noise elements of the generic methodology and provides a model for the prediction of the composite sound pressure level and the equivalent noise exposure levels of groups of individuals from machines, used singly and in combination in an underground environment based on the sound pressure level determined according to SABS-ISO 3744 under free field conditions. The methodology includes provision for the consideration of the effect of hearing protection devices and the use of multiple machines in combination and provides an indication of the potential costs of hearing compensation.

Jan 1, 2006

More than 410,000 visitors from 171 countries helped bauma ’04 set new attendance records at the world’s largest construction machinery and mining technology show. The show, held in Munich, Germany March 29-April 4, marked bauma’s 50th anniversary. At the last bauma show in 2001, attendance was about 406,000 people from 157 countries. At bauma ’04, international attendance increased to 31 percent from 27 percent in 2001. In addition to record-setting attendance, bauma ’04also attracted 2,801 exhibitors, up from 2,341 in 2001. Exhibitors came from the United States, Europe, China, Japan and the Middle East. Exhibitor space topped 500,000m2 (5.4 million sq ft), another record. And, for the first time, there were more foreign exhibitors than German exhibitors, show organizers said.

Jan 1, 2004

By X. Louw

"This paper examines the change in surface properties of the Polyurea used on spirals at different operational times: unused spiral, 28 months in operation and 58 months in operation. This is being done to investigate the alleged statement that spirals have a decrease in spiral separation efficiency after a certain period of operational time. Observing the surface characteristics under 1.5x and 36x magnification it can be concluded that the surface roughness decreases with increased operational time. This may be explained by a decrease in air inclusions and streak lines as the spiral surface wears. Decreased surface roughness should in theory have a beneficial effect on spiral separation performance. This leads to the conclusion that if a decrease in spiral separation performance is observed after a certain period of operation, it can’t be attributed to the change in surface properties. Uneven wear of the spiral surface, material creep or application of force to the spiral will change the profile of the spiral and could cause an adverse effect on spiral separation performance. The metallurgical test work showed that the best results are obtained at 30 - 35% solids by mass in the spiral feed. The iron recovery was significantly higher in the new spiral in comparison to the 2012 and 2010 spirals. The mass yield to concentrate in the new spiral was approximately three times more than for the older spirals. In conclusion, the yield combined with the grade, which equals the recovery was the best for the new spiral.IntroductionAn investigation was launched to research the common belief that spirals experience a decrease in efficiency, and therefore recovery, after a certain period of operation (a period of seven years has been used in the industry). The properties of the spiral that may have an effect on the efficiency are:"

Jan 1, 2017

Recovery of Fine Gold Particles from Philippine Gold Deposits by Enhanced Gravity Concentration and Flotation The objective of the study is to determine the applicability of enhanced gravity concentration (EGC) and flotation for gold recovery. While gravity concentration methods have long been applied to gold ores, especially to free-milling types that requires minimal beneficiation, flotation for gold recovery has not yet taken hold as a major operation in the Philippine setting. In this study, the application of EGC and flotation for gold is applied and compared to the existing methods for gold recovery. Two samples, with assays of 7.315 and 5.333 g Au/MT (samples 1 and 2, respectively) are used for this study. These samples are subjected to mineralogical studies and is found to have a gold-particle size ranging 10 to 200 microns. To verify the separation size, the mesh-of-grind (MOG) is used as the primary parameter for experimentation. Initially, the samples are stage-crushed, ground, and subjected to EGC using a Falcon SB40 Concentrator. Based on the results, the two samples showed that recovery increases with a finer MOG. The ratio of concentration (K) decreases with a finer MOG. This shows that there should be sufficient liberation of the gold values for EGC to be effective. The effect of the enhancement is to pronounce the difference in specific gravity of the minerals, promoting better separation. This is validated by the high recovery values of 86.97 per cent and 98.73 per cent exhibited respectively for samples 1 and 2 (at 54 microns). For the flotation runs, sample 2 with an average particle size of 80 per cent passing 74 microns is examined using thiocarbamate-based collectors for roughing and subsequently exhibited a recovery of 96.32 per cent. At this point, the concentration ratio (K) is noted as an important efficiency indicator for flotation process since it yielded a very low-mass and high-metal content concentrate.

Sep 13, 2010

By E. D. Calvert

The objective of this research was to examine variations in melting and forging practice for four titanium-base alloys and to determine their effect on the resultant product. Of particular interest was the evaluation of the skull-casting technique. The data should serve as a guide to producers and consumers of titanium products. Physical properties of four titanium-base alloys in ingot form and in sheet form were evaluated and correlated, where possible, with variations in the melting and casting procedure. Consumable-electrode melting was used throughout, but arc current and furnace backfill pressure were varied, and ingots were formed both by melting directly into a water-cooled copper mold and by skull melting followed by pouring into a graphite mold. Alloying metal additions for the alloys tested were (1) 8 percent manganese, (2) 6 percent aluminum and 4 percent vanadium, (3) 6 percent molybdenum and 2 percent aluminum, and (4) 16 percent vanadium and 2.8 percent aluminum.

Jan 1, 1962

By Walter E. Vanderpool

Full scale load tests are frequently performed immediately prior to deep foundation construction to verify the design assumptions. Occasionally, load tests are performed during design development and applied to the final design for critical and non-redundant structures. We believe that full scale load tests can be very valuable and economical for projects, especially in a geologic environment where the record of full scale load testing is very limited or non-existent. The load testing for the Utah Transit Authority?s Airport Light Rail Trax project provides an example of the advantages of a load test in design development. The savings realized by the owner was in excess of $800 thousand dollars.

Jan 1, 2011

By W. J. Birch, D. Leckenby, R. Farnfield

The use of electronic detonators to improve fragmentation is becoming universally accepted. However their use in limiting peak particle vibrations levels is still in its infancy. Most of which is anecdotal, in that few actual scientific studies have been carried and published. This paper details the research work carried out at a limestone quarry in the County of North Yorkshire in Northern England. Here a series of blasts were carried out some used non-electric detonators whilst others used electronic detonators. The majority of blasts were carried out at the same burden, spacing and deck charge weight loadings. Initially, the key variable was the difference in detonator type and then leading on to using the electronic detonators at specific exact different detonator timing intervals. Later the study was extended to include double row as well as single row blasts.

Jan 1, 2007

By S. H. Miller

Biodegradable hydraulic fluids can save tens or hundreds of thousands of dollars in fines and clean up costs in the event of a hydraulic fluid leak or spill. When properly selected, applied, maintained and monitored, a biodegradable fluid will have a long useful life and will protect equipment as well as or better than conventional petroleum based hydraulic fluids.

Jan 1, 2000

By Drupad B. Desai, Bruce Chang, Jay L. Merritt

This paper reviews difficult ground conditions encountered along the alignment of large-diameter sewage tunnels for the City of Los Angeles. It offers a detailed one-of-a-kind solution to a unique problem for shallow urban underground tunnels in a seismic zone, using state-of-the-art materials, technology, and equipment. The following topics are discussed in detail: • Geotechnical Design consideration for tunnel traversing through an active fault zone. • Seismologist evaluation of possible fault-offset problems where a fault zone crosses the alignment, in the event of an earthquake of moment-magnitude 6.5. • Probability analysis regarding "recurrence interval." • Structural design of tunnel subjected to displacement, subjected to axial elongation or shortening, and capable of rotational freedom. • Special joint details.

Jan 1, 1989

By A. G. Doll

"Many power-based grinding models exist, and most operators are familiar with Fred Bond's ""third theory"". Bond's model is most commonly used to describe primary and secondary grinding to product sizes above, for example, 100 µm. Operators sometimes use Bond's equation to describe grinding in situations where it is not appropriate, such as fine grinding below 50 µm. Using an alternative model would be a better choice in this situation.Bond's equation is one in a large family of models. Related equations better suited to fine grinding include the “signature plot”, Von Rittinger's model and Charles' equation. These models have a similar form to Bond's and can be fit to industrial regrind mills and laboratory tests using the simple regression tools in the charts of computer spreadsheets. Operators will find that fine grinding calculations are both easier and more accurate when using the alternative equations to fit their regrind milling surveys or when performing laboratory regrind mill scale-up for plant design.None of these models are new: Charles' equation was published in 1957 and Von Rittinger's model was proposed in 1867. A quick refresh how to apply these equations can turn these oddities from the undergraduate curriculum into useful tools for plant optimization. They can be fit to any type of mill including stirred and tumbling ball mills.IntroductionBuilding a case for fine grind modelling requires reviewing some theory before building a framework for doing fine grinding calculations. The actual calculation procedure recommended is easy and can be applied by plant metallurgists. Don’t be frightened by the theory; the end result is reasonably simple.The observation that mineral breakage is related to the absorption of energy is usually attributed to Von Rittinger (1867). Lynch and Rowland (2005) describe that the ability to empirical test and calibrate energy models of breakage didn’t exist until the widespread adoption of electric motors in the mining industry during the 1930’s and 1949’s. A series of technical papers published by the Allis Chalmers company during the 1940’s demonstrate that they were attempting to do such a calibration using Von Rittinger’s model which is usually stated as: “the energy consumed in the size reduction is proportional to the area of new surface produced.”"

Jan 1, 2017

By K. Hanna

This U.S. Bureau of Mines report describes a rock mechanics instrumentation program conducted in a shallow underground coal mine in central Illinois. This research program was designed to provide a basic understanding of the structural behavior of entry intersections. A wide variety of instruments and measurement techniques including hydraulic borehole pressure cells, multiple-point borehole extensometers, roof bolt compression pads, and overcoring were employed to monitor roof stresses, pillar loading, strata movement, floor heave, and bolt loading before, during, and after intersection development. A summary of intersection design theories, failure modes, and support techniques is included and instrumentation installation procedures and analysis methods are presented. The study identified two critical parameters that affect intersection stability: in situ horizontal stresses and geological discontinuities. Important design parameters for improving intersection stability are roof span and intersection geometry.

Jan 1, 1991

By Thomas P. Kwiatkowski, Joginder S. Bhore, Christopher D. Orlandi, Jose Velez

Three case histories of successful TBM tunneling for New York City Water Tunnel No. 3 are presented. The tunnels, costing about one billion dollars total, are the 5-milelong, 18'-11" OD Brooklyn Tunnel; the 5-mile long, 23'-2" OD Queens Tunnel, and the9-mile long, 12'-4" OD Manhattan Tunnel. The three tunnels are the first major tunnels constructed in New York City rock utilizing the TBM method of construction. This paper describes and compares the three tunnel projects in terms of geology, construction methods, TBM’s, rock and groundwater behavior, rates of advance and other performance data, and challenges and solutions encountered during the projects.

Jan 1, 2007