Search Documents

By George J. Conroy

Electrical power generation was studied in a laboratory-scale, open-cycle vortex MHD generator, which offers several advantages over straight-channel generators that require separate combustors. Compactness, lower capital cost, and high-energy release are obtained by combining the combustor and generator into one unit in the vortex generator. In addition, the vortex generator uses a simple solenoid rather than the more complex and expensive saddle magnet required for straight channel generators. Although the vortex generator must utilize combustion gases with a low Hall coefficient in order to be efficient in direct comparison to the linear generator, the primary motivation for this experimental device in terms of ultimate objective was to investigate the vortex generator with applications to direct coal firing and with combustion taking place in specially designed expansion nozzles. The vortex device offers one decided advantage over the linear device in this regard because slag deposits do not degrade or short-circuit the coaxial electrodes as is the case for a linear machine. The experimental vortex generator consists of a modified cyclone burner 7 ½ in ID by 21 in long, with the inner wall used as one electrode together with a coaxial center electrode. Power was obtained by impressing an axial field of 3,000 G from an air core solenoid magnet. Tests were conducted by seeding natural gas seeded with potassium acetate and burning with preheated oxygen-enriched air. Power generation was lower than calculated because theoretical plasma velocities were not achieved.

Jan 1, 1972

By D. Turnbull, H. N. Treaftis

Precipitation of tin from Pb-Sn alloys (lead-rich) occurs by the nucleation and growth of hemispherical cells which consist of tin lomelloe interspersed in the depleted solid solution. Nucleation and growth of these cells and the tin interlamellar spacing at various compositions and temperatures have been investigated. The interlamellar spacing increases approximately as the reciprocal of the logarithm of the supersaturation ratio. For constant initial tin concentration the concentration of cell nuclei increases with decreasing temperature to a limiting temperature-independent value. The kinetic results support the view that the cell growth rote is governed by the diffusion of tin along the cell boundary. In the main, the results confirm the authors' earlier deductions, drawn from resistometric and calorimetric data, about the precipitation mechonism. IT has been shown1, 2 that tin (ß) precipitates from lead-rich (a) PbSn solutions by the nucleation and growth of cells (cellular or discontinuous precipitation). These cells consist of tin lamellae, with a spacing 1, interspersed in a depleted a solution. Reorientation of a also accompanies cell growth. The kinetics of cellular precipitation of tin from lead have been measured by resistometric2, 3 and ca1orimetric1, 3 techniques. The time-transformation isotherms (t equals time; x, volume fraction of specimen transformed) of the initial rapid precipitation, which drains about 60 pet of the tin from solution, have been described by a kinetic law having the form x = 1 —exp (—bt n) [I] where n usually has the value 3.0. It was shown" that this law and the other kinetic facts can be explained satisfactorily if it is assumed that the cells grow at a constant rate and that all the cells nucleate in a time negligible in comparison with the period of cell growth before impingement. Thus, for hemispherical cells b = (2/3)pNG3 [21 where G is the rate of cell growth in cm per sec, and N is the number of cell nuclei per unit volume. The rapid rate of cell growth at low temperatures can be accounted for"' if it is assumed that the dissolved tin drains to the lamellae edges by diffusion along the sweeping cell boundary rather than by diffusion through the a crystal (volume diffusion). For cell growth governed by cell boundary diffusion it was shown, approximately G=2(X° - X° / X° ) DBA / l2 where A equals the thickness of the cell boundary; D R, the coefficient of diffusion of tin atoms within the boundary; and X° and X, are the atom fractions of tin in the supersaturated and saturated solutions, respectively. Zener8 had already shown that, where

Jan 1, 1959

By Brad Thrall

"Viceroy Resource Corporation of Vancouver, B.C. has recently developed the Brewery Creek Mine, an open pit heap leach gold mine 55km East of Dawson City in Yukon, Canada. Mineable reserves are 17.1 million tonnes of ore grading 1.45 grams/tonne, containing 24.8 tonnes (797000oz) of gold. Ore processing employs the heap leach technology using run of mine ore. 1996 highlights included construction of 158,000 m2 of leach pad, placing 1.9 million tonnes of ore at a grade of 1.46 gpt on to the leach pad, construction and successful commissioning of the ADR plant, and pouring of the first gold bar on November 15th.Permitting this mine has drawn significant attention because the heap leach technology, while proven in other jurisdictions, has not been used in Yukon where winter site temperatures routinely reach -45 C for extended periods.IntroductionFollowing a comprehensive governmental and public review of the proposed project, a Class A Yukon Water license was issued in August, 1995. Construction started in 1995 and leaching commenced in October 1996. The Brewery Creek Mine is in Yukon, the home of the Klondike Gold Rush nearly 100 years ago. This is the only part of Canada not glaciated in the Wisconsin advance so there is oxide ore resulting from about 80,000 years of weathering -unique in Canada. Discontinuous permafrost is present on site and has required special consideration in the design. Winter temperatures dip below minus 50 C, demanding an approach to mining and leaching that is different than in more temperate climates.Project DescriptionThe mine comprises 8 shallow, largely oxidized gold deposits along a 7km corridor. An 8 year mining program will extract 17.1 million tonnes of ore grading 1.45 grams/tonne, containing 24.8 tonnes (797,000 oz) of gold. The strip ratio will be 1.35: 1. Overall gold recovery is projected at 78%. There will be 2.3 million tonnes of ore placed on the pad annually, with an average of 2.57 tonnes (83, 000 oz) of gold recovered per year. Because of the cold winters, the mine will operate approximately 210 days per year, while the leaching process will operate on a year round basis. Run of mine ore is placed on the heap 150 days per year. The recovery process utilizes conventional sodium cyanide leaching , carbon adsorption, caustic desorption, and on-site smelting. Peak employment during mining is 145 and winter staff is reduced to 45."

Jan 1, 1997

By David S. Yang

The Cement Deep Soil Mixing (CDSM) method introduces and mixes cementitious materials with in situ soils using hollow-stem rotating shafts equipped with a cutting tool at the tip and mixing paddles above the tip. CDSM generally produces a soil-cement panel consisting of three overlapping soil-cement columns. The soil-cement panel is then extended to form walls, which are effective for excavation support and groundwater control due to the continuity and low permeability of soil-cement walls. Two design approaches could be taken in the application of CDSM for excavation support: 1) single wall design and 2) gravity wall design. The former one is treated as a wall technology and the latter one is treated as a soil stabilization method. This paper will review the CDSM equipment and installation procedures for the construction of these two types of soil-cement walls. Four case examples are used to illustrate the design and application of these two types of soil-cement walls.

Jan 1, 2003

By P. W. Lotz

Traditionally, bottle roll tests have been used to optimize the extraction process for best gold extraction and recovery. Such tests typically involve exposing the ore to defined reagent concentrations (lime, cyanide and sufficient oxygen) and balance the gold input with recoveries and losses. With mounting pressures to accommodate sustainability issues during development work, it became apparent that much more information would be required on the interactions and kinetic behaviour of solid and solution species during the entire leach process. This information is vital to enable proactive management of critical issues such as cyanide, arsenic, water and tailings management. Inadequate management of these aspects has led to temporary closures and, in cases of non-compliance, to the dynamically changing regulations. MINTEK?s advanced leach facility (ALF) is being developed with the aim of bridging the knowledge gap between the gold leach process and the predictable environmental impacts upon discharge. The facility aims to monitor all parameters of relevance such as pH, Eh, dissolved oxygen, metals, cyanide species, and viscosity during the entire process to enable more informed decisions on practical interventions. The presented set of data reflects first experiences gained from processing a refractory gold ore concentrate. Attempts at optimizing the process were limited due to the developmental nature of the work. Data relating to leaches with differing preoxidation conditions and cyanide staging is presented.

Jan 1, 2009

By Turnbull A. G

Thermodynamic calculations based on the ideal system NiO - Fe203 - H2(g) - CO(g) - H2O(g) - CO2(g) show that it is not possible to selectively reduce nickel oxide in the presence of hematite because ferronickel is the zero-valent nickel-containing product. The calculations show that temperature, reducing atmosphere composition and oxide to reductant ratio have a marked effect on the nickel content of the ferronickel alloy and the amount of nickel reporting jn the alloy. The general trends based on the calculations correlltte well with experimental observations.

Jan 1, 1980

By Glenn S. Dobby, Glenn A. Kosick

"Column flotation circuit engineering has matured to a good level of understanding regarding testing, scale-up and design. Some of the factors important to the process of implementing columns are addressed in this paper, highlighting the following issues• operating bias and the maximum achievable solids carrying rate for a column application.• internal circulating loads of full scale and pilot plant flotation columns• short-circuiting oflarge scale columns and the impact on separation selectivity• the number of stages in a column circuit and the impact on selectivity.The paper uses several case studies, from pilot plant to full scale implementation, to illustrate these design issues.1. IntroductionTen years ago, in 1984, there were very few column flotation installations world wide and the largest columns were about I . 5 to 2 m diameter or square. During the following decade there have been in the heighbourhood of 80 column installations that have been successful and profitable, as both retrofits and green-fields plants. Now, columns as large as 3 to 4 m are not uncommon. Examples of installations with many large columns include Escondida, with ten columns each at 4 m square, and P T Freeport Indonesia, with 21 columns: nine 3 m diameter columns, four 2.4 m diameter columns and, starting up in April I 995, eight 3.6 m diameter columns.During this growth period there have also been column installations that can be considered as failures. In the majority of these cases, the reason for their failure has been an insufficient installed capacity for applications where there is a high weight recovery of solids to the froth product These include zinc cleaning, copper cleaning and iron ore flotation (silica flotation from a feed that is 15 to 30 %Si02) An application with high weight recovery to the froth product makes column scale-up and circuit design more complicated. This is particularly so if a high degree of selectivity is also required while attaining a high weight recovery, which can happen with iron ore flotation in columns."

Jan 1, 1995

By Steve Kral

Commodity price down cycles are a fact of life in the mining industry. And companies pre-pare for them as best they can. Evenso, operations are still curtailed or closed during those cycles, profits shrink, layoffs are inevitable and many companies do not survive. However, one of the few good things that occurs during down cycles is the new, innovative exploration, mining and processing technologies that come about during hard times. To survive the lean times, the mining industry turns to improved technology to decrease costs and hold the bottom line. And, because mining is a cyclical business, each down cycle brings about technology improvements that carry over into the good times.

Jan 1, 2004

By John E. Urosek, Dennis A. Beiter, William J. Francart

In This Chapter [Designing bleeder systems Examining and maintaining bleeder systems Evaluating bleeder system effectiveness] INTRODUCTION Bleeder systems are that part of the mine ventilation network used to ventilate pillared areas in underground coal mines. Pillared areas are those in which pillars have been wholly or partially removed, including the areas where coal has been extracted by longwall mining. Bleeder systems protect miners from the hazards associated with methane and other gases, dusts and fumes, and oxygen deficiency that may occur in these mined-out areas. Effective bleeder systems control the air passing through the area and continuously dilute and move any methane-air mixtures and other gases, dusts, and fumes from the worked-out area away from active workings and into a return air course or to the surface of the mine. A bleeder system includes the pillared area (including the internal airflow paths), bleeder entries, bleeder connections, and all associated ventilation control devices that control the air passing through the pillared area. Bleeder entries are special air courses designed and maintained as part of the mine ventilation system. [This chapter focuses on the design, examination, maintenance, and evaluation of bleeder systems in underground coal mines.] The history of coal mine explosions in the United States is a reminder of the importance of adequate ventilation. Some of those disasters were the result of inadequately ventilated pillared areas. The importance of developing bleeder systems to ventilate these pillared areas and evaluating the bleeder system’s effectiveness is reflected in present-day federal regulations. For more information on bleeder systems, see Tisdale [1996] and Urosek and Francart [2002].

Jan 6, 2006

By Ed Beswick

Resource Update Drilling Program ? Pre-feasibility ? Exploration Metallurgy Program ? Grindability ? Metallurgical Optimization ? Hydrometallurgical Options Preliminary Mine Development Design Environmental Permitting Infrastructure Development

May 1, 2008

By Don Rose

INTRODUCTION A number of tunnels supported and permanently lined by steel-fiber-reinforced shotcrete (SFRS) have been built in North America in the 1980s. The material is more economical than, and technically equal or superior to, conventional shotcrete using wire mesh. The design and construction of SFRS-lined tunnels is straightforward, and only a few new design principles, laboratory tests or construction equipment modifications appear necessary in order to use this material. Modern tunnel Contractors may use cyclic drill-and-blast methods on some tunnels, with intermittent shotcreting as part of an orderly cycle. The Dry Mix method is most suitable for cyclic, intermittent, relatively small-scale shotcreting. However, modern Contractors excavating tunnels continuously using large long Tunnel Boring Machines (TBMs) or Roadheaders may prefer Wet Mix shotcreting on a mass production basis. In either case, the use of steel-fiber-rein¬forced shotcrete (SFRS) promotes the rapid and economical excavation of tunnels. The addition of microsilica will improve SFRS properties and reduce rebound, and is expected to become standard practice with SFRS in North America, as it now is in Scandinavia. HISTORICAL REVIEW Steel-fiber-reinforced shotcrete (SFRS) at the present time (1985) is essentially conventional shotcrete with straight or deformed steel fibers added, and in general SFRS for tunnel linings encounters the same problems that conventional shotcrete does. Shotcrete history is well known. The use of sprayed plaster on wire frames for mounting animal skins by Carl Akeley of the Smithsonian

Jan 1, 1985

By H. H. Power, C. H. Pishny

When an oil operator becomes a party to a proration agreement he may wonder, with good cause, whether production prorated .today is merely deferred until tomorrow or whether oil might be lost. Various types of evidence obtained from production records when studied quantitatively are of great assistance in arriving at definite conclusions. A study of individual examples cited in this paper leads towards some solution of the problem, particularly when they are considered in the aggregate. Many production curves on various pay horizons were studied. A disappointingly large number of these were of contributory value, but inconclusive. However, there were enough curves of similar type from the Wilcox sand at Earlsboro, Bowlegs, Seminole City, the Cromwell horizon at Little River, and the Simpson dolomite at Valley Center, Kansas, from which reasonably definite conclusions were drawn. Assuming that deferred production is later made up with no increase in ultimate recovery, a curve (Fig. 1) shows the normal flowing and pumping life of a composite well, contructed by the family curve method. The initial production of the well shown is 1700 bbl. daily and the allowed production is 25 per cent. On this basis the average daily allowed rate for the first month is 425 bb1., or the area BCDE, which is equivalent to the area AFDG under the normal decline curve. The potential production for the second month is 1500 bbl. and the allowed production 375 bbl. daily. By this procedure a potential curve for each succeeding month is obtained (points A, H, I, J and K). If the well is opened it should produce somewhere near its potential curve for a short period and then decline at a more rapid rate than the potential curve. This theoretical analysis is basic. Actual examples exhibiting all points raised by the ideal curve are rare. Proration in the Mid-Continent area has been effected mostly by leases rather than by individual wells; hence a well may produce any

Jan 1, 1931

By Y. X. Zhao

This paper briefly describes the characteristics and induced factors of coal mining bumps based on the investigation of recent bumps accidents occurred in China. According to the theory of non-equilibrium thermodynamic and dissipate structure, the process of strain energy accumulation and dissipation in the ?Coal-Surrounding Rock? system (CSRS) is discussed during the preparation of coal bumps. In addition, a series of experiments are conducted to analyze the relationship between bump-prone property and micro-structural characteristics of coal. The process of coal bumps induced by propagation of fractures and deterioration of coal mass properties are also analyzed systematically.

May 1, 2009

By J. E. Rourke, O&apos

A wide variety of techniques and equipment are available for coring soft or poorly consolidated geological material. This report presents a comprehensive literature review and evaluation of these techniques and equipment. A potential user will find guidelines in this report to assist him in selecting sampling equipment. A bar chart shows what samplers have been used under what geological conditions, and gives the specific literature references. Two matrices rate the present techniques and equipment with respect to reported success for sampling specific materials, and with respect to several performance characteristics including complexity of use and core quality. These matrices are supplemented with tables of typical sampling equipment. and program costs. Near-term future developments are seen primarily in improved training of drillers, and in instrumenting the drilling operation to provide objective data on drilling characteristics. An extensive annotated bibliography, a catalogue of equipment suppliers including specifications and cost ranges, and a list of manufacturers and distributors are appended to the report.

Jan 1, 1978

By A. E. Ketler

Conventional Atmospheric Monitoring System (AMS) installations for monitoring CO, CH4, O2 and air-velocity throughout underground mines are usually relegated to a modest 3-5 mile extent and with data communication speeds confined to a ponderous 1-5K baud range. New US-MSHA and state regulations require fast reporting of unsafe conditions, and the old 20-30 minute updates are no longer acceptable. To communicate farther and faster has always been a problem, because data reliability degenerates with excessive distances and high speeds. Because of this, very large mines often resort to costly optical-fiber media, using expensive OF cables and repeaters to obtain the necessary coverage. This entails high initial cost, as well as high maintenance and downtime costs to repair or replace broken optical fibers. Rel-Tek has pioneered with its DX-Bus communication data highway, which uses inexpensive twisted-pair telemetry cables, which can now communicate well into the 20-mile extent of the largest mines -- normally a brick wall for low-tech AMS systems. This extended range, enables the use of twisted-pair cables and provides a low cost alternative to OF systems. This paper discusses the DX-Bus, and its latest accomplishment, the ?B-LINK,? a unique high-speed communication repeater that maintains the 19.2K-Baud data rate. On-going innovations to our workhorse Millennia-DX computer software have kept pace with this extra speed/distance phenomenon, resulting in a dually-optimized AMS package: both hardware and software. Cost savings are substantial, and at no sacrifice of reliability ? nearly always at 100%. Sensor updates are measured in seconds, not minutes and hours. Twisted pair copper cable is cheap to purchase and install and a breeze to maintain. Rel-Tek uses the B-LINK's wide branching capabilities to enable the AMS to extend 20-miles both far and wide. Actual experience in large US coal mines -- both longwall and continuous mining operations -- confirms the large mine performance. The ventilation and safety benefits to the mining industry are immeasurable.

Jan 1, 2009

By Wilson D, Kirkland J

Compressed air energy storage (CAES) uses low cost off-peak energy to compress air and pump it into pressurised underground storage. Expanding the air through a modified form of gas turbine generates electrical energy when required. While generating power, a CAES station consumes approximately one-third of the gas required for the equivalent installed capacity of a conventional gas turbine. Air can be stored in underground rock caverns, caverns in salt domes, or in aquifers. Existing CAES power stations use caverns mined out of salt domes. Aquifer storage for CAES has been proposed, but not yet implemented. The groundwater in the aquifer would be displaced during air injection and when required the air would be extracted using the natural hydro-static pressure. Victoria has no salt domes, but has aquifers onshore in the Gippsland Basin with geological dome structures of suitable depth, discovery pressure, porosity, permeability and caprock for CAES development. Field tests costing several million dollars would be required to prove the suitability. The most suitable aquifer is near Seaspray, where several dome structures exist. The aquifer, comprising of coarse sands capped by coal and mudstone, is some 600 metres deep with a hydrostatic pressure of 6.3 MPa. Computer simulation of injection and extraction of air from the aquifer under various combinations of horizontal and vertical wells, permeability and tubing head pressures indicated the largest aquifer structure had the capacity to sustain a 300 MW station. A well field comprising of 24 directionally driven wells with a horizontal exposure to the aquifer would achieve the air flow rates required. Using plant similar to that recently installed at McIntosh Alabama USA, would mean high capital costs compared to standard gas turbine plant. However, a review of modem gas turbines indicated that they could be easily and economically adaptated to CAES duty. Adapting a 120 MW gas turbine would give 344 MW output. A separate air compression plant would be used. Economic evaluations indicate that, for gas prices above $1.95 per GJ, a 344 MW CAES plant is more economic for intermediate/reserve load duty than simple cycle gas turbines.

Jan 1, 1992

By F. Cihangir, A. Kesimal, K. Karaman, B. Ercikdi

Uniaxial compressive strength (UCS) and shear strength parameters(cohesion and angle of internal friction, Cand F) of rocks are important parameters needed for various engineering projects such as tunnelling and slope stability. However, direct determination of these parameters is difficult and requires high-quality core samples for tests. Therefore, this study aimed to explore the applicability of the Brazilian test (BT) - a simple, less sophisticated and inexpensive method for both specimen preparation and testing - to estimate the UCS and shear strength parameters of rocks. Thirty-seven rock types were sampled and tested, 24of which were volcanic, 8 were metamorphic, and 5 were sedimentary. Statistical equations were derived to estimate the UCS and shear strength parameters of rocks using the BT. The validity of the statistically derived equations was confirmed using predictive analytics software (PASW Statistics 18). A strong linear relation was found between BT and UCS values. BT and UCS values exhibited prominent linear correlations withthe cohesion values of rocks. The Mohr envelope was also used to determine the cohesion and friction angle of rocks using BT and UCS values. It is deduced from the current study that the BT values can be used to estimate the UCS and cohesion. However, no relation was observed between the angle of internal friction values and the UCS and BT for all rock types. Therefore, different approaches are suggested for the estimation of the internal angle of friction for application in the preliminary design of projects.

Jan 1, 2015

By A. B. Cecala

Video technology coupled with data logging exposure monitors have been used to evaluate worker exposure to different types of contaminants. However, previous application of this technology used a stationary video camera to record the worker?s activity while the worker wore some type of contaminant monitor. These techniques are not applicable to mobile workers in the mining industry because of their need to move around the operation while performing their duties and tasks. The Helmet-CAM is a recently developed exposure assessment tool that integrates a person-wearable video recorder with a data logging dust monitor that are worn by a miner in a backpack, safety belt, or safety vest to identify areas or job tasks of elevated exposure. After a miner performs his or her job while wearing the unit, the video and dust exposure data files are downloaded to a computer and then merged together through a NIOSH-developed computer software program called EVADE (Enhanced Video Analysis of Dust Exposure). By providing synchronized playback of the merged video footage and dust exposure data, the EVADE software allows for the assessment and identification of key work areas and processes, as well as work tasks that significantly impact a worker?s personal respirable dust exposure. The Helmet-CAM technology has been tested at a number of metal/nonmetal mining operations and has proven to be a very valuable assessment tool. Mining companies wishing to use this technique can purchase a commercially available video camera and an instantaneous dust monitor to obtain the necessary data, and the NIOSH-developed EVADE software will be available for download at no cost on the NIOSH website.

Feb 27, 2013

By K Gordon

A methodology for assessment and remediation of acid mine drainage (AMD) developed at the Sullivan Mine in the West Coast Region has been applied to the closed Blackball Mine, Blackball, West Coast Region. AMD from the Blackball Mine has low pH, high acidity, and elevated levels of iron, aluminium, manganese, nickel, zinc and arsenic. The AMD flows at a variable rate (36 - 101 L/s) into adjacent Ford Creek, causing an increase in acidity and trace element concentrations in the creek. To test the effectiveness of treatment with a simple limestone-based treatment system, a column leaching experiment was conducted over a nine day period. The results show effective removal of acidity, reduction in the concentrations of iron, aluminium, manganese and zinc, and production of alkalinity. To determine if this treatment method reduces the toxicity of the AMD to aquatic invertebrates, a 96 hour ecotoxicity experiment was conducted. The results show a significant decrease in mortality in the treated AMD compared to untreated. The column experiment, in conjunction with the ecotoxicity work, suggest that a passive treatment system consisting of a limestone leaching bed and an open limestone channel may be sufficient to treat the AMD from the Blackball Mine. Further work, such as large-scale treatment trials, is recommended.

Jan 1, 2004

Pressure drops were measured in a column packed with glass spheres and wax particles, both in random and preferential distributions. Variables investigated included wax content, gas flow rates, and temperatures.It is shown that for random distribution of wax, pressure drop is exponentially related to wax content above the melting point of wax and that below this it increases with increasing gas rate and temperature.For preferred distribution of wax the highest increase in pressure drop is obtained with horizontal distribution of wax and the least with vertical distribution.Comparison with operating blast furnace data and application of results to practice are also included.

Jan 1, 1970