Search Documents

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crushed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summaries of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling at the same group of quarries. OBJECT Or STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

By Nan Wang

Based on the commercial computational fluid dynamics software, Fluent, the fluid flow and temperature field in an iron-bath reactor were simulated numerically, and the effects of top-blown and side-blown operating parameters on the mixing time of iron bath, distribution range of oxygen in top space, and post-combustion ratio were investigated. The simulated results showed that the mixing time of iron bath increased initially and then decreased with the increase of inclined degree and immersion depth of side-blown lance. The distribution range of oxygen became wider as pulling the top lance away from the iron bath. Furthermore, post-combustion ratio was reduced given the top lance was too close the bath. The simulation results provide theoretical base for the process optimization of iron-bath reactor and further development of new type iron-bath smelting reduction process.

Jan 1, 2009

By R. Greenwood

The advent of the space age and its promise of interplanetary flight has prompted new ideas for propulsion systems that will allow maximum energy with minimum fuel weight. The use of cesium as the source of energy for such rocket flights has been found desirable. Theoretical efficiency of a rocket fuel is measured in terms of specific impulse, defined as the number of pounds of thrust per pound of propellant consumed per second. Specific impulse is usually expressed in seconds (the number of seconds for which one pound of fuel would produce one pound of thrust) although it is really a measure of total energy, not of power. The most sophisticated chemical fuels have a specific impulse of 300 to 400 sec; liquid hydrogen heated by nuclear reactor has a specific impulse of 1000 to 1200 sec. Specific impulses as high as 20,000 sec, however, are theoretically attainable with the ion rocket, in which free cesium ions are accelerated across a voltage drop and ejected at high velocity.' Characteristics of the system have been sketched by Boden.2 The desirable properties of an ion propellant are: 1) low ionization potential, 2) low boiling point, and 3) high atomic weight. Alkali metals best fulfill these requirements, and Table I indicates the superiority of cesium. The use of heavy complex ions such as UCl3 is ruled out by their instability and other disadvantages.' Despite its enormous superiority in specific impulse, the ion rocket is inherently low-powered, capable of very small acceleration. Application of ion propulsion will be limited to large rockets and spaceships on missions requiring powered flight for weeks or months and employing a separate chemical propulsion system for escape from the earth's atmosphere where power requirements are large but of brief duration. For example, Kraemer and Larson3 considered the case of an unmanned 25,000-lb pay-load placed in a 300-mile orbit by chemical rockets, proceeding thence by ion propulsion to the vicinity of Mars, where it would go into orbit once again. Calculations provide for 8500 lb of cesium for such a voyage. The question of whether such quantities of cesium will be readily available to the space program does not appear to have been considered by geologists and mining engineers. Present Production and Uses Literature on industrial applications of cesium is scanty. The metal is used in scintillation counters, photocells, infra-red detection devices, and as a "getter" in low-voltage vacuum tubes. Production is sporadic and total figures are not published, but the annual consumption is measured in pounds rather than in tons. The few pollucite deposits known, small as they are, can easily supply the present limited demand for gram or pound lots of cesium. Until recently the price of cesium was $2 to $4 per gram, but according to Chemical Engineering, cesium salts are now available at $13 to $27.50 per lb. Geochemical Distribution As a large alkali ion, the cesium ion accompanies potassium in geological processes and tends to be concentrated in the latest crystallizing fractions of potassium minerals in much the same manner as rubidium. Most of the cesium in igneous rocks, therefore, is in the micas and potash feldspars of granites, and especially in granitic pegmatites. The cesium content rises markedly in the micas of the late by-drothermal replacement stage in complex pegmatite~.' Typically, cesium is only 0.5 to 0.01 times as abundant as rubidium in potassium minerals. Rb', with a radius of 1.47 A, is close enough in size to K' (1.33 A) so that rubidium forms no minerals of its own. Cs+ is so large (1.67 A) that only small concentrations can be taken up in potassium minerals; when cesium is present in solution in larger concentration it forms the mineral pollucite, Cs3-Na2A17Si17O48.3H2O, which is known only in pegmatites. In the weathering of igneous rocks, cesium is dissolved, carried to the ocean, and apparently in-

Jan 1, 1961

Whilst much has been written in past years by geologists, scientists, mining engineers, etc., regarding the well·known and justly notorious anticlinal, or, as they are more commonly known, " saddle" reefs of Bendigo, comparatively little noticehas been given to the synclinal or "inverted saddle "reefs and their relationship with each other. In taking up the question of the synclinal folds, I recognise that it is a large undertaking to confine within the limits of a short paper, and at the same time convey a comprehensive idea of their characteristics, and the importance of their relationship with the anticlinal folds, in the general question of practical mining. However, from a practical point of view I consider the question of great importance, and if an interest in it can be awakened, more particularly among practical men, the object of this paper will be achieved.Before entering into the subject I must briefly state some facts, and perhaps some theories, in respect to the deposition of the Lower Silurian rocks, and their subsequent buckling up, as now seen on the Bendigo gold-field. At the same time, I do not intend to go very closely into the geological aspect of the question, as I wish the paper to be considered as a practical one.

Jan 1, 1902

By A. R. Dover

The Richmond-San Rafael Bridge is a 6.92 kilometer (4.3 mile) long major toll bridge span that crosses the northern San Francisco Bay in a highly seismically active region. Tutor-Saliba / Koch / Tidewater JV was contracted by Caltrans to conduct a comprehensive seismic retrofit. The JV provided geotechnical planning and quality control services as described herein, under normal oversight by Caltrans. Part of the robust foundation retrofit design included the installation of 26 new, large diameter piles, including eleven 3.81 m (12.5 ft) diameter, cast-in-drilled-hole (CIDH) marine piles that were drilled 9.15 m (30 ft) into the bedrock beneath the Bay, where the water depth ranged up to about 21.3 m (70 ft). These reinforced concrete-filled composite piles have a steel shell permanent casing from the bridge substructure pile cap through the water column and 30.5 to 39.6 meters (100 ft to 130 ft) of marine sediments to the top of rock. This paper discusses construction, inspection (ranging from the QA employed in the planning of the CIDH pile installation methods and equipment to the actual construction inspection required for the routine installation of the shafts), problems that were encountered during construction, and the solutions that were developed and implemented. Inspection, particularly with the usual difficulties in the marine environment, coupled with the difficult and complex bedrock conditions was particularly challenging, and ranged from non-destructive testing to "in-water, inshell" diver inspection. Similarly, the complexities of dealing with both the steel casing "riser" and the associated drilled shaft (rock socket) portion of these composite foundation elements created some unusual issues. The paper also presents important lessons learned from the project.

Jan 1, 2008

By Nick D. Rose

The Dy deposit is a 21 Mt Pb-Zn-Ag-Au SEDEX-type massive sulphide resource located in the Anvil District, Faro, Yukon. This relatively unexplored orebody lies at a depth of 480 to 920m below surface, dips 20 to 35o and comprises vertical ore thicknesses of 3 to 28m at a 9% Pb + Zn cut-off grade. The deposit has been tested at depth with 63 surface diamond drillholes, but has not yet been explored or developed by underground means. Over the past decade, pre-feasibility investigations were conducted for two separate owners of the property to determine the economic viability of developing an underground mine at Dy. Following these previous studies an assessment was undertaken between 1998 and 2000 to further investigate geotechnical considerations for underground mining. The results and conclusions drawn from this study provide direction for possible future exploration at Dy.

May 1, 2002

By J. Moyes

The Intec Process is a generic process for the production of pure base metals and precious metals from sulphides concentrates derived from copper, nickel, zinc and lead ores. The development program for the Intec Process initially focussed on the treatment of copper concentrates, (the ?Intec Copper Process?), and more recently of zinc concentrates, (?the Intec Zinc Process?). Developed and proven in Sydney, Australia at a cost of US$15m over the last ten years, the Intec Copper Process is now ready for commercial application. The knowledge gained during the development of the Intec Copper Process has been applied to the Intec Zinc Process, which utilises the same basic chemistry to produce high purity zinc ingot from metallurgically complex zinc sulphide concentrates containing lead, copper, iron, silver and gold. The demonstrated ability of the Intec Zinc Process to treat low grade mixed zinc/lead/copper concentrates, including those with high iron and manganese levels, holds out the real prospect of overcoming major metallurgical hurdles that have long affected the zinc industry. The Intec Zinc Process consists of the three consecutive circuits of leaching, purification and electrowinning. The leach circuit is of single stage configuration with a series of reactors to which concentrate and lixiviant are fed. Purification consists of cementation and precipitation by pH adjustment. Electrowinning employs an electrolytic cell very similar in design to that of the Intec Copper Process, but differs in that a conventional plate cathode is produced. During electrowinning, the same mixed halide species (BrCl2 -, HalexTM) that is integral to the Intec Copper Process is generated in solution at the anode and exhibits powerful leaching characteristics capable of directly leaching the sulphide concentrate feed. The need to roast the concentrate prior to leaching, as is practised in the conventional Roast/Leach/Electrowin (RLE) process, is thus eliminated whilst a range of by-products (notably lead, copper and precious metals) can be extracted in the simple, single-stage leach. This paper describes the Intec Zinc Process; the technology, predicted economics and its environmental aspects.

May 1, 2002

By Gray Mullins

This paper presents results from model and full-scale tests to assess the interface bond between a cast-in-place concrete seal slab and steel H-piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid was displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also tested. In the model tests, eight 15 cm deep, W6 x 15 sections were used for two different embedment depths of 1.5d and 2d, d being the depth of the section. In the full-scale tests, 16 specimens 35 cm deep (W14 x 90 sections) were tested with the embedment varied between 0.5d-2d. The results show that significant bond stresses developed even in the worst placement condition. Recommendations made for revising current values in specifications have already been implemented by the Florida Department of Transportation.

Jan 1, 2013

By W. Persson

The first installation at a copper smelter of a Semtech OPC System for continuous, on-line production control of copper converting in PS converters took place in 1994. At present OPC systems are installed at 19 PS converters. The technology presents to the operator real-time information on the progress of the process he is controlling in the form of optical process parameters, thus facilitating dynamic process control. The optical process parameters are based on time- and wavelength resolved registrations of the light emitted by the off-gas flames and identification of correlation between these parameters and characteristic metallurgical process data. The present paper provides a description of the technology as seen by the furnace operators and a summary of operating experiences made during five years of full-scale, operation at various smelters, reviews influences from the technology on smelter operational practises and comments on recent developments as regards new applications of the technology.

Jan 1, 1999

A study of the accessory opaque iron-titanium oxide minerals of the Oiles Complex, central Australia, was an Important complement to an investigation of the magnetic properties of the Complex. These minerals constitute no more than 10 per cent of the rocks sampled, and generally less than 1 per cent of the ultramafic rocks ("magnetite" concentrations were not sampled for magnetic investigation).Titanomagnetite is the main opaque mineral present, although ilmenite exsolution has been widely developed. High-temperature oxidation of these produced mainly titanohematite, pseudobrookite and rutile. Both exsolution and high-temperature oxidation developed along specific crystallographic directions (along {111}), and in Irregular patches. Low-temperature oxidation is generally not well-developed, indicating the small degree of weathering in the rocks sampled.Although the Oiles Complex is layered, no apparent overall preferred orientation of the iron-titanium oxide minerals was observed, other than crystallographically controlled alignment of very fine grains within pyroxene crystals. Other textural features of the opaque oxides are restricted to symplectic intergrowths mainly with the ferromagnesian silicates.

Jan 1, 1971

By Richard B. Moore

This bulletin presents a summary of available information regarding the sources of uranium, radium, and vanadium, the methods used in treating the ores, and the uses of the finished products. In particular the paper describes the ores found in the United States, giving especial attention to those characteristics of the ores and the conditions of their occurrence that affect mining and treatment. ACKNOWLEDGMENTS. In the preparation of this bulletin a number of persons rendered assistance by furnishing information and by making it possible for us to visit the carnotite deposits in western Colorado and eastern Utah at a time of the year when without this assistance it would have been difficult to obtain satisfactory results. We desire to express our thanks to the following persons: Henry Hall, W. L. Cummings, T. V. Curran, K. D. Hequembourg, David Taylor, H. C. Brown, Forbes Rickard, George W. Alsdorf, Dr. Herman Fleck, Orr J. Adams, C. S. Cherrington, Newt. Stewart, O. B. Willmarth, Angus Cameron, George A. Head, and Lorimer Bros.

Jan 1, 1913

By Dupuy. Leon W., R. T. C. Rasmussen, W. A. Calhoun

"INTRODUCTION For many years it has been known that low-grade manganese deposits occur in the bluffs along the Missouri River Valley. Frequent attempts have been made to develop the ore and to produce a marketalble commodity but they have had little success. Under pressure of the war emergency and the shortage of manganese, the attention of the Federal Bureau of Mines was directedtoward the deposits.Manganese-bearing shale occurs from a point near Pierre, S. Dak., down the river to the Rosebud bridge near the Nebraska line (1).5/ The Bureau of,confined its work to the more accessible central portion of the deposits near Chamberlain, S. Dak. The ore occurs principally as concretionary nodules in the form of iron and manganese carbonates (manganosiarite and perhaps some manganocalcite; rhodochrosite has not been identified). At the surface the carbonate is often broken down so that the oxide of manganese gives the nodules a black The matrix or host rock is generally known as Pierre shale, composed of ""interbedded layers of bentonite, an altered volcanic ash, and dissemi¬nated bentonite particles,"" (2) and montmorillonite-beidellite clay minerals (3). The shale weathers to the very sticky gumbo characteristic of South Dakota and well-known to hunters and travelers in the area.The area selected for the experimental mining and pilot-plant work discussed in this report lies about 8 miles westerly from Chamberlain and is a few hundred feet north of U. S. Highway,16, on land owned or controlled,by M. Q. Sharpe of Kennebec, S. Dak., and the General Manganese Corp."

Feb 1, 1946

By H. H. Stoek

MINE models have three distinct uses: 1. As exhibits in expositions and museums. 2. As exhibits in law suits. 3. As illustrations in teaching mining engineering. All three uses are in a sense educational. The third, or distinctively teaching function, has not been extensively developed in America as it has been abroad, chiefly because of the cost of the models and the scarcity of model makers. In connection with expositions, such as the Columbian, the Louisiana Purchase, and the Panama-Pacific, a number of very good mine and metallurgical models were prepared with funds furnished by State commissions, by mining organizations or mining companies. At the close of these, expositions, some of these models have been deposited in National or State museums or in educational institutions, but too many of them have been lost, or have been stored, away in some mining company's office or in the basement of some State building, where they have been lost sight of and have gradually fallen to pieces. A visitor to a German mining school is impressed by two facts: 1. The mining laboratories are in general inferior to those in America. 2. The mining museums are infinitely superior -to ours, particularly in models exhibited. One may reply to this comparison by saying that a museum is necessarily a work of time. From the historical standpoint this is, of course, true, but it is not necessarily true in connection with a working museum intended to illustrate current practice. For instance, the oldest mining school in Germany, that at Freiberg, has much excellent historical material, but very little on modern practice, while Berlin, one of the youngest German mining schools, has a most extensive and valuable collection of modern appliances and models. This is true in spite of the fact that one of the best-known model shops is at Freiberg, from which many of, the models to be seen in America have come. Because many of the models in American mining schools have come from

Jan 4, 1917

By R. Bellotti

The theory of cavity expansion in an infinite frictional soil mass whose strength is represented by a curved Mohr-Coulomb failure envelope has been used to predict with some confidence the cone resistance of a clean dry sand. Experimental data were obtained from cone penetration and pressuremeter tests on two sands, conducted in a large calibration chamber (CC) under carefully controlled placement and boundary conditions. A plane strain bearing capacity theory was developed, and to convert the results to axi-symmetric conditions, an empirical "shape factor" was used. In the paper, the theoretical background, experimental data, calculation procedure, and the results of the analysis are presented. In general, a reasonable validation of the cavity expansion approach to the bearing capacity of deep foundations has been obtained.

Jan 1, 1987

By M. du Plessis

This paper describes the evaluation of a limit equilibrium model to simulate the behaviour of crush pillars in platinum mines. An analytical model was derived to calculate the residual average pillar stress (APS) values of the crush pillars. The values predicted by this model were compared to the numerical values obtained from TEXAN simulations. In general, the limit equilibrium model appears to be very attractive for simulating pillar failure as the gradual crushing of the outside of the pillar and the transfer of stress to the intact core can be replicated. The value of the TEXAN crush pillar model was further demonstrated by simulating an idealized layout with crush pillars between two adjacent panels. The simulations illustrated that oversized pillars will not crush close to the face and this may lead to seismic failure in the back area. An important finding of the study is that closure measurements may prove to be a very valuable diagnostic measure in crush pillars layouts. Distinct differences in magnitudes of closure were simulated for a scenario where the pillars crush as expected, compared to the scenario where an oversized pillar is left. Experimental closure data collected in a crush pillar stope provided further evidence regarding the value of closure measurements in these layouts.

Jan 1, 2011

By H. A. Dierks

Implementation of the joint Federal-State control program established in 1955 to cope with the mine water problem in the Pennsylvania anthracite region is described in this report. The increasing severity of the water problem in the anthracite mines has necessitated major adjustments as this continuing program has progressed. Since 1941 the Federal Government has recognized the mine water problem as an important factor in the worsening economic condition of the anthracite region by initiating scientific and technologic investigations and establishing the Anthracite Flood-Prevention Section in the Bureau of Mines in 1948. On the basis of comprehensive investigations and studies, the results of which were published in numerous reports and bulletins, the Anthracite Mine Drainage Commission of the Commonwealth of Pennsylvania formulated a plan that served as a background for legislative action in 1955, resulting in Public Law 162, 84th Congress (Act of July 15, 1955 (69 Stat. 352; 30 U.S.C. 571-576)), for the Federal Government, and Act No. 82 of the General Assembly, July 7, 1955, for the Commonwealth of Pennsylvania. The report covers 29 mine flood control projects approved and executed in implementing the aforementioned legislative acts. Essential engineering and cost details for each project are given, together with an evaluation of the effect that the installed facilities have on alleviating the mine water problem as it concerns individual mines and the anthracite industry as a whole.

Jan 1, 1962

By I. W. van der Merwe

Recently, a new kind of filtration has emerged, namely nano-filtration (NF). It is a membrane-based process which exhibits totally unique separation characteristics for dissolved salts as well as for many non-charged species. By exploiting the particular separation characteristics of this new membrane type, many unique and novel separations have been made possible. The basis for separation by nanofiltration is the negative surface charge of the membrane. This results in rejection of multivalent anions, whilst associated cations are also rejected to maintain electro-neutrality. This peculiar property enables separation of dissolved ions such as sulphate and copper from acid, whilst the acid may be purified for reuse. This paper aims at providing an overview of the principles of nanofiltration, illustrated by particular examples.

Jan 1, 1998

By J Wallis

The stability of a raise bore is often assessed using the rock mass classification system published by McCracken and Stacey as a modification of the Q system. Often the assessment is done using a spreadsheet to manipulate geotechnical log(s) of boreholes. This paper discusses the inherent difficulties with this approach. Recent work by others to provide guidelines to the classification system is discussed. A recent example of the design and raise bore performance at Macraes Gold Mine, New Zealand is presented. A key issue is that a visual assessment of the drill core and/or core photographs is necessary to æground-truthÆ the classification.

Jan 1, 2008

While the United States and the rest of the world struggles with record-setting oil prices Canadian oil sands producers are ramping up production to meet demand for oil while also fighting against a host of negative images. In recent months, the price of oil has skyrocketed. Most of that oil comes from Saudi Arabia. In Alberta, Canada there are unconventional oil reserves that rival those in Saudi Arabia in the vast Canadian oil sands, sometimes called the tar sands. Proponents of the oil sands say that Alberta?s oil sands can be a secure source of oil and energy for the United States for many years to come. With new mining and drilling projects, the industry has said that it could quadruple its production to nearly 4 million bbl/day by 2020. Time magazine once called the oil sands, ?Canada?s greatest buried treasure that could satisfy the world?s demand for petroleum for the next century.? So why hasn?t the United States embraced this close, politically secure source of energy? Because, getting usable fuel from the oil sands can be a dirty business, say opponents. The oil sands are a combination of clay, sand, water and bitumen. It is a heavy, black, thick oil. Oil sands can be mined and processed to extract the oil-rich bitumen, which is then refined into oil. The bitumen cannot be pumped from the ground in its natural state. Instead, tar sand deposits are mined, usually using strip mining or openpit techniques, or the oil is extracted by underground heating with additional upgrading. These methods require a huge amount of energy and water and produce a large amount of carbon emissions. Environmental groups that have long spoken out against the oil sands projects got some political backing in the United States in June when a group of mayors from large U.S. cities spoke out against the oil sands, as did presumptive Democratic candidate for U.S. president Barack Obama?s senior energy advisor. During a convention of large-city mayors in Miami, FL, Alberta?s oil sands were singled out in a nonbinding resolution calling for national guidelines to track the lifecycle impact of different types of fossil fuels. The resolution urges cities not to use unconventional sources of energy with a large carbon footprint, such as liquid coal and oil shale and oil sands.

Jan 1, 2008

By F. T. Wang, Y. Yuan, S. H. Tu, X. G. Zhang

Hydraulic support instability (HSI) is one of the most common causes of disasters in underground coal mining, posing a threat to the safety of mine workers and normal operation of the equipment. It is prone to occur in fully-mechanized mining faces with a large mining height (FMMLMH), especially when the dip angle of the coal seam is large. The key to controlling HSI is to deduce its mechanism and employ effective control techniques. This paper focuses on the analysis of HSI types, the key parameters and techniques to control HSI in FMMLMH, the establishment of a model of HSI in FMMLMH, and a multi-parameter sensitivity mechanical model of different HSI forms in the no. 7219 longwall face in Xutuan Coal Mine, Huaibei Mining Group, by using sensitivity analysis . The results show that HSI mainly presents in three forms: hydraulic support gliding (HSG), hydraulic support tilting (HST), and hydraulic support tail twisting (HSTT). The occurrence of the above three forms depends mainly on support anti-instability capability. In the no. 7219 longwall face, HSG and HST are the main two forms of HSI. The dip angle of the working face and the friction coefficient between floor and hydraulic support are the sensitive parameters for HSG, while HST is strongly dependent on the dip angle of the working face and the friction coefficient between roof and hydraulic support. By the applications of measures such as the oblique layout of the working face, cutting the floor into a step pattern, moving the support under pressure, and raising the setting load, the support stability was controlled effectively.

Jan 1, 2015