Search Documents

By B. Xu

Keywords: Magnetic damping, g-jitter, Hot-film anemometry Results from an experimental study on natural convection induced by temperature gradient in molten gallium contained inside a rectangular container. The damping effect of the convective flow from an externally applied static magnetic field is investigated. Induced velocity and temperature fields are mapped using a standard constant temperature hot-film anemometry and a thermocouple with and without the applied magnetic field, respectively. Detailed experimental setup and procedure are depicted in the present paper. Obtained velocity and temperature profiles are examined against previous numerical simulations and reasonably good agreement has been achieved. Obvious damping effect can be observed in both the temperature and the velocity profiles when the external magnetic field presents.

Jan 1, 2005

By Alaina B. Hanlon

Keywords: Undercooling, Convection, Dendrites, Stainless Steel, Levitation Certain Fe-Cr-Ni stainless steel alloys solidify from an undercooled melt by a two-step process in which the metastable ferrite phase forms first followed by the stable austenite phase. Recent experiments have shown that the lifetime of the metastable phase is strongly influenced by flow within the molten sample. The current research will provide insight to why flow affects the metastable phase. This new understanding will lead to the use of convection to control microstructural evolution in spray-forming of stainless steels. Simulations using a commercial computational fluid dynamics package, FIDAP, yield a range of convective flow velocities that cause mechanical damage to the dendrites which is compared to experimental results. If the convective velocities are great enough that the dendrites bend, then low angle boundaries form at the points of collision. These result in high energy sites that could serve as nuclei for the stable phase.

Jan 1, 2005

By P. N. Anyalebechi

The effects of solidification rate on the cast microstructures of aluminum alloys 6009 and 6016 have been investigated with directionally cooled laboratory-size ingots, at 0.2-10.1 K/s and 0.4- 23.1 K/s, respectively. These ranges of solidification rate are within those observed in commercial-size ingots. In both alloys, the average dendrite cell size and second phase particle size decreased with increase in average solidification rate and with a decrease in average local solidification time. However, at comparable solidification rates, the dendrite cells and second phase particles are finer in the shorter freezing range alloy 6009 than in the longer freezing range alloy 6016. This is provisionally attributed to the earlier formation of second phase intermetallics at higher temperatures during solidification and to the formation of greater amount of the relatively coarse plate-like ß -phase (Al9Fe2Si4) phases in alloy 6016. In general, in both alloys, the types and relative amounts of the second phase particles in both alloys are independent of solidification rate.

Jan 1, 2006

By M. I. Brasileiro

The use of experimental design to the study of mixtures has found a wide range of applications, even in laboratory scale or in industrial development works. The aim of this work was to maximize granite sawing waste content in ceramic tiles using experimental design. Based on the raw materials, specific formulations were developed using the experimental design. The raw materials were mixed and sample bodies were produced using uniaxial pressing. The sample bodies were fired and characterized in terms of water absorption, mechanical strength and X-ray diffraction. Regression models were adjusted relating the water absorption and mechanical strength with the amount of raw materials. The results showed that the methodology of experimental design maximize the content of wastes incorporated in ceramic tiles formulations. Formulations containing up to 40% of waste can be used for the production of ceramic tiles.

Jan 1, 2009

By Stanko Nikolic

One of the keys to success in process development is incremental scale-up, allowing for potential problems to be identified and rectified. The ISASMELT™top submerged lance (TSL) process was developed to maturity using this method by Mount Isa Mines, now owned by Glencore. Commercialization only occurred once the process had been proven on each scale and as a result the ISASMELT™ technology now operates successfully around the world. An important parameter in the evolution of the technology has been the furnace campaign life. The initial commercial scale furnaces had minimal water-cooling. Although this led to shorter campaign lives, an extended development program resulted in the achievement of four-year campaign lives, without any water cooling. In tandem to the refractory designs Glencore Technology, supplier of the TSL technology, has progressed cooled copper lining designs for application to both the ISASMELT™ and ISACONVERT™ furnaces allowing for ultimate flexibility in the lining choice. This allows each ISASMELT™ operating site to minimize their overall life-cycle costs by balancing their campaign life with lining costs, energy inputs, and other shutdown requirements.

By Dongok Kim

Regardless of the advantages of the Friction Stir Process (FSP), for age-hardened aluminum alloys, the mechanical properties such as hardness in the stir zone decreased after FSP due to the growth or dissolution of strengthening precipitates. Here, as a new technique, FSP was introduced to alloy copper nanopowders in Al7075 T651. Mechanical properties of copper nanopowder- alloyed Al7075 T651 together with micro and nanostructures were compared with those of as-FSPed Al7075 T651 using SEM, TEM, and Vickers hardness testing to understand structure-property relationships. It was observed that Vickers hardness of the stir zone in copper nanopowder alloyed Al7075 T651 increased by 20% compared to that of the heat affected zone, while the as-FSPed samples did not show a noticeable increase in hardness in the same zone. Xray mapping showed traces of copper nanopowder after the process. TEM is being used to verify if there was CuAl2 formed in the copper alloyed sample.

Jan 1, 2006

By David B. George

Kennecott Utah Copper adopted Outokumpu Flash Smelting and Kennecott-Outokumpu Flash Converting in 1995, a process based on granulating high grade copper matte. While nickel mattes and very small quantities of copper matte had been commercially granulated for years, no large scale copper matte granulation system had been built. This paper summarizes the history and benefits of copper matte granulation, the Kennecott design basis, the successful operation for over 10 years and potential problems inherent in some matte granulation approaches.

Jan 1, 2006

By W. M. Cross

Bubble attachment time measurements for the rare-earth phosphate minerals monazite and xenotime were made as a function of oleate concentration, sodium fluoride addition, and temperature. Results indicate that the rare-earth phosphates behave similarly to other phosphate minerals, notably collophanlte and fluorapatite, which have been studied previously. The addition of sodium fluoride yielded a modest decrease in bubble attachment time with fluoride additions below the apparent fluoride surface precipitation point, while at fluoride additions greater than the apparent precipitation point a significant decrease in attachment time occurs. Increasing the temperature or the system gave a slight decrease in bubble attachment time in the absence or sodium fluoride. With sodium fluoride addition and below the apparent fluoride surface precipitation point, an increase in temperature actually increased the attachment time. For sodium fluoride additions above the apparent fluoride surface precipitation point, a temperature increase significantly decreased the attachment time.

Jan 1, 1989

By F. A. Guo

Ultrafine-grained surface layers were obtained by surface mechanical attrition treatment (SMAT) in copper and titanium samples. The thermal properties of the deformed layers were characterized using a scanning thermal microscopy (SThM) that allows thermal conductivity to be mapped down to the submicrometer scale. A theoretical approach, based on this investigation, was used to calculate the heat flow from the probe tip to the sample and then estimate the thermal conductivities at different scanning positions. Experimental results and theoretical calculation demonstrate that SThM can be used as a powerful tool for the thermal property and microstructural analysis of ultrafine-grained microstructures.

Jan 1, 2006

By Yuanbo Zhang

Keywords: Complex Iron Ores, Roasting, Tin, Zinc, Pellets, Comprehensive Recovery. The complex iron ores containing tin, zinc are typical refractory ores. Large reserves of the ores are found in China and have not been utilized efficiently so far. A new process of tin and zinc recovery and pellet preparation from iron concentrate containing tin and zinc by controlled atmosphere roasting is developed in this investigation. The results of 2573 N/P compression strength of product pellets, the 91.49% and 82.22% volatilization of tin and zinc respectively, are achieved for a concentrate containing 0.39% tin and 0.28% zinc. The strength and chemical compositions of the pellets meet the requirement of blast furnace ironmaking. Volatilization mechanism of tin and zinc are investigated. Thermodynamic study shows that the reduction balance curves of SnO2(s) and SnO(g) are proximate in the presence of carbon, and the standard formation free enthalpy of FeO and SnO2 is also approachable. Therefore, it is difficult to realize the complete volatilization of tin in the form of SnO(g) by selective reduction. But SnO2(s) and SnO(g) will form SnCl4(g) or SnCl2(g) in the presence of chlorides and can be easily volatilized from the ores.

Jan 1, 2005

By Carlos M. Fontes Vieira, Ruben J. Sanchez Rodriguez, Carlos E. Gomes Ribeiro

"The worldwide demand for ornamental stones in building construction is motivating the use of their wastes, generated during fabrication, to produce compound stones. This work has as its objective to investigate the production of an ornamental compound marble (OCM) under vacuum and compression processing of a polyester matrix composite with addition of marble waste as load and as filler. Square OCM composite plates were subjected to compression and flexural mechanical tests. Samples were analyzed to obtain the density and water absorption. The OCM composites presented properties within the expected range of an artificial stone.IntroductionMarble is a limestone, composed mainly of calcite, more or less crystallized by metamorphism that ranges from granular to compact in texture. It has a density 2.7 g/cm3 and its porosity is approximately 0.4%. The UNI 8458 standard defined marble as: ""every crystalline rock constituted mainly by minerals with a Mohs hardness equal to 3-4"". In marble production around70 - 75% of whole extract material is lost in byproducts generation [1,2].In function of large volume of residues generated, the ornamental stones industry has attracted ever more the attention of environmentalists [3].Actually the marble can be pulverized to obtain calcium carbonate for industrial applications. It is also possible to obtain a thinner powder to produce concretes [l]. Some authors study the use of stone residues in concrete mortars and ceramic bricks, getting better properties to these materials [3,4].The marble residues can be also used in engineered stones, or ''agglomerated"" stones, production. The most common engineered stones in the market consist, like a polymer concretes, in polymer matrix composites incorporating petreous components. In the formulation of the engineered stones, the particulate or granular petreous components are the result of fragmentation or trituration processes to which natural stones were submitted to [ 5]."

Jan 1, 2014

By Zhan Jing

Keywords: thermodynamic, Ni-Co alloy powders, composition, fibrous The mathematics model of Ni(II)-Co(II)-C2O42?-NH3?H2O-H2O of thermodynamic equilibrium system has been developed theoretically according to the law of conservation of mass and the law of simultaneous equilibrium, and the logarithm concentration-pH (log[Me2+]T-pH) diagrams of this system have been made. The effect of ligand and pH value was studied. Two issues in coprecipitation route to synthesize fibrous nickel-cobalt alloy precursor powder, com-position and morphology which are a first priority, are addressed based on thermodynamic analysis and experiments. The results show that suitable pH value range of coprecipitation of nickel ions and cobalt ions in theory can be obtained to maintain fibrous, excellent compositonal homogeneity and stoichiometry in coprecipitation products. Experimental demonstration is also carried out.

Jan 1, 2005

By C. M. F. Vieira

This work has as its objective to characterize ceramic bodies for vitrified tiles elaborated with the mixture of nepheline-syenite flux and kaolinitic clay. Formulations were prepared with 0, 30 and 50 wt.% of nepheline-syenite incorporated in a kaolinitic clay. To determine the physical and mechanical properties such as dry bulk density, linear shrinkage, water absorption and flexural rupture strength, specimens were prepared by 30 MPa uniaxial pressure-molding and then fired in a laboratory furnace at 1150oC. The microstructure of the fired ceramics was evaluated by scanning electron microscopy. The results indicated that the nepheline-syenite improved the evaluated properties of the clay and attended the specifications of vitrified ceramic tiles.

Jan 1, 2010

By Lucas Lopes da Costa

In this work, a natural foam extracted from the Amazon buriti palm tree is investigated as possible substitute for synthetic foams. The basic physical and mechanical properties of this biofoam were evaluated. Its sponge-like structure was characterized by the amount of pores and morphological aspects. It was found that the buriti biofoam displays a very low density of the order of 0.1 g/cm3 with a relatively good compressive strength. This would be suitable for several engineering applications and as a new material with the potential for replacing currently applied synthetic polymeric foams.

Jan 1, 2010

By Cem Colakoglu

In this study, nickel containing iron alloys were produced by carbothermal reduction of lateritic nickel ores obtained from Manisa - Caldag region of Turkiye in order to investigate the reaction mechanism of nickel and cobalt. In the experiments, the lateritic ore containing 1.58 wt.% Ni and 0.12 wt.% Co was calcined in a semi-pilot scale rotary furnace at 1100°C for 1 hour. Then, a mixture of calcined ore and metallurgical coke was reacted in sintered alumina crucibles using a graphite resistance tube furnace at different time (0- 60 min) and temperature (1500-1600°C).

Jan 1, 2009

By Olga Frank-Kamenetskaya

The experimental results of study of atmospheric corrosion processes on Saint-Petersburg bronze monuments surface, received in situ and by means of simulating experiments, have been discussed. Influence of the time factor on corrosion film (patina) mineral composition has been analyzed. Direct dependence between patina mineral composition and environmental conditions has been proved. The sequence of patina phases crystallization has been established. Effect of the chemical composition and heterogeneity of artistic bronze and also monument surface structure on the rate of corrosion process has been regarded. The time variations of mass of the crystallized in the hydrochloric acid vapor phases have been investigated. The kinetic laws of their development at the initial stage of formation, indicating simple (non chain) reactions, have been revealed.

Jan 1, 2006

By Tian Sugui

By means of the measurement of the enduring property and microstructure observation, an investigation has been made into the influences of the element Re and TCP phase on the enduring property of the single crystal nickel base superalloys. Results show that the needle-like TCP phase is precipitated along the <110> orientation on {111} planes in Re-containing/free superalloys during the long term aging, the TCP phase is identified as µ phase, and the precipitated µ phase in 4.5%Re alloy is gradually spheroidized during aging. Thereinto, the needle-like µ phase may obviously decrease the enduring lifetimes of the alloys due to the consumption of the refractory elements and the effect of the stress concentration. But the stress concentration is not easily generated in the regions near the spherical-like µ phase, which is a main reason of reducing the enduring lifetime of 4.5%Re alloy to a small extent.

Jan 1, 2010

By G. N. Shannon

Keywords: inclusions, slag, modeling, interfacial energy, capillary force, particle flotation, particle separation A previously introduced model of inclusions separating across a steel-slag interface, developed by Nakajima/Okamura and Bouris/Bergeles, is expanded to include different inclusions shapes (octahedral and plate-like, besides spherical) as well as comparison between model ladle-, tundish-, and mold-slags. Investigation of the relation of these shapes with the interfacial capillary force ? which arises due to the dynamic interfacial energy during separation ? has shown that the force has a significant effect on whether the inclusion separates rapidly or settles at the interface. For the slags considered, the most significant physical property is found to be viscosity, which resulted in fast separation times for inclusions in the mold and ladle slags, relative to the more viscous tundish slag. Particle dissolution (using experimental data) is included in separation modeling.

Jan 1, 2005

By Hamed Mirzadeh

The hot working behavior of 17-4 PH stainless steel was studied using the hot compression test at temperatures of 950-1150 °C with strain rates of 0.001-10 s-1. A step by step procedure for data analysis in hot compression test was given. The work hardening rate versus stress curves were used to reveal whether or not dynamic recrystallization (DRX) occurred. At low Zener- Hollomon (Z) parameter, this material showed a new DRX flow behavior, which was called Multiple Transient Steady State (MTSS). At high Z, as a result of adiabatic deformation heating, a drop in flow stress was observed. The general constitutive equations were used to determine the hot working constants of this material. Moreover, after a critical discussion, the deformation activation energy of 17-4 PH stainless steel was determined as 337 kJ/mol.

Jan 1, 2010

By A. L. D. Skury

In the synthesis of diamond, the precursor graphite must present a degree of crystallinity to assure optimum yield and quality for the transformed crystals. X-ray diffraction, SEM and TEM analyses were carried out to investigate the structural and morphologic transformations produced in natural graphite by high pressure-high temperature treatment. The present study had as its objective to characterize the morphological and structural changes suffered by a natural graphite that was subjected to high pressure and high temperature treatments in the region of diamond thermodynamic stability. The results indicate that the material that constitutes the gasket, for the deformable capsule, could act as catalyst in the graphite recrystallization process.

Jan 1, 2006