Search Documents

By Kimio Itagaki, Torn Matsumoto, Makoto Ohtsuka, Kentarou Harada

"The structure and hydrogen-absorption properties of LaNis thin films were investigated in the present study. LaNis thin films were prepared by a sputtering method with a radio-frequency power, Ws, of 50 -400 Wat substrate temperature, Ts, of323 -573 K. Nickel content of the films decreased with increasing Ws, however, there was no dependence on Ts. At low Ws and low Ts, amorphous films were deposited. In other conditions, the films were polycrystalline. The films prepared at high Ws and low Ts, or at low Ws and high Ts, exhibited only a (h k · 0) peak in the X-ray diffraction profiles. This indicates that the c-axis of crystalline films was oriented parallel to the substrate plane. At high Ws and high Ts, the films with columnar structure were obtained. Hydrogen-absorption capacity of the thin films increased with increasing Ws. The pressure plateau did not appear on the pressure-composition isotherms. The films deposited at high Ts represented a higher equilibrium pressure.IntroductionThin films of hydrogen storage alloys can be applied for an electrode of rechargeable battery or fuel cell, a filter for H1 purification and various kind of sensor. Some studies on the preparation of the thin films of LaNi5 intermetallic compound, which is a typical hydrogen storage material, have been done hitherto. Adachi et al. , 2) and Sakaguchi et al. 3) prepared amorphous and crystalline LaNi5 thin films using flash evaporation of alloy powders and measured the pressure-composition isotherm for the prepared film utilizing a quartz crystal mass monitoring (QC:MM) method. It was found that the prepared amorphous film absorbed hydrogen without disintegrating into the powders and the hydrogen-absorption capacity of the films increased with the degree of crystallinity. Sakai et al. 4) reported that the maximum hydrogen storage capacities of amorphous and crystalline LaNi5 thin films, fabricated by a RF sputtering method using combination targets, were about 40 mA h g-1 (LaNisHo.7) and 160 mA h g-1 (LaNi5H2.6), respectively. Uchida et al. 5, 6) prepared LaNi5 thin films using flash evaporation of alloy powders and measured volumetrically the pressure-composition isotherm for the prepared film. It was reported that the hydrogen-absorption capacity of the films changed by the annealing treatment."

Jan 1, 1998

By Guangwei Wang, Changle Zheng, Yifan Chai, Jian Guo, Weiwei Geng, Jianliang Zhang

In this paper, characteristic and kinetics of CO2 reaction with four different kinds of coke such as top-loading coke, dry quenching tamping coke, wet quenching tamping coke and semi-coke were investigated based on isothermal method. Electric resistance reduction furnace was used to heat the sample. Volume Model (VM) and Shrinking Core Model (SCM) were used to calculate the kinetic parameters and to contrast with the experimental results. The results showed that the Volumetric Model (VM) was much suitable for the reaction of top-loading coke, dry quenching tamping coke and wet quenching tamping coke, while Shrinking Core Model (SCM) was much suitable for semi-coke.

Jan 1, 2015

By Maija-Leena Metsiirinta

The behaviour of copper and lead in zinc roasting has been studied in laboratory scale roasting experiments as well as in large scale trials in an industrial fluidized bed, with the background of Outokumpu Kokkola Zinc smelter. Commercial zinc concentrates with a low and high ( up to 3 wt % ) copper content and with a low and high ( up to 3.5 wt % ) lead content were oxidized to various desulphurisation degrees in the fluidized bed to establish the reaction mechanisms and the paths for copper and lead oxidation in the roasting. Influences of the agglomerate size on the roasting kinetics and micro- scale phenomena were also determined. Optical microscopy was used on the calcine and the findings are presented as numerous photographs of the polished cross sections. SEM/EDS techniques were used for analyzing chemically the phases and particle morphologies present in the samples. Computational thermodynamics was applied to the complex phase equilibria occurring during roasting in the agglomerating calcine. A complete oxidation of zinc concentrate with a high copper and lead content requires a careful control of oxygen coefficient in the roasting in order to maintain a stable operation of the fluidized bed. Oxygen coefficient thus seems to have a significant impact on the hydrodynamic stability of the fluidized bed with fine raw materials.

Jan 1, 2003

By Maija-Leena Metsärinta

The behaviour of copper and lead in zinc roasting has been studied in laboratory scale roasting experiments as well as in large scale trials in an industrial fluidized bed, with the background of Outokumpu Kokkola Zinc smelter. Commercial zinc concentrates with a low and high ( up to 3 wt % ) copper content and with a low and high (up to 3.5 wt % ) lead content were oxidized to various desulphurisation degrees in the fluidized bed to establish the reaction mechanisms and the paths for copper and lead oxidation in the roasting. Influences of the agglomerate size on the roasting kinetics and micro-scale phenomena were also determined. Optical microscopy was used on the calcine and the findings are presented as numerous photographs of the polished cross sections. SEMIEDS techniques were used for analyzing chemically the phases and particle morphologies present in the samples. Computational thermodynamics was applied to the complex phase equilibria occurring during roasting in the agglomerating calcine. A complete oxidation of zinc concentrate with a high copper and lead content requires a careful control of oxygen coefficient in the roasting in order to maintain a stable operation of the fluidized bed. Oxygen coefficient thus seems to have a significant impact on the hydrodynamic stability of the fluidized bed with fine raw materials.

Jan 1, 2003

By J. Wong

We report a successful use of x-ray absorption spectroscopy to probe the chemical and structural environment of trace elements in coal. When applied to vanadium in coal, it was found that vanadium exists in at least two environments: a trivalent site 6-fold coordinated by oxygens at ca. 2.0~ and a tetravalent site 5-or 6-fold coordinated also by oxygens, one of which forms a short V=O bond at ca. 1.6a. No evidence of nitrogen (porphyrin)1'or sulfide environment was found. It was also found that the vanadium environ-ments in the raw coal did not survive unchanged in a liquefaction process. These findings have implications for coal cleaning processes and for trace element release into liquefaction process streams.

Jan 1, 1982

By Tibor Zoltai

Asbestos is a generic term for industrially useful fibers recovered from exploitable deposits of the asbestiform varieties of five silicate minerals: chrysotile, anthophyllite, actinolite-tremolite, cummingtonite-grunerite, and riebeckite. Asbestos and asbestiformm fibers of some other minerals are known to be carcinogenic. Minerals crystallized in the asbestiform habit are characterized by unique properties (morphology, strength and flexibility, physical and chemical durability, and defect-free surface structures). The key to the unusual properties, and health effects, of asbestifarm fibers appears to be in their unusual surface structure. In contrast, non-asbestiform crystals of the same minerals, including the five so-called asbestos minerals do not have these properties and are not carcinogenic (1, 2).

Jan 1, 1989

By Patricio Ruz, Gabriel Riveros, Carolina Ramirez, Andrzej Warczok, Rober Treimer

"Continuous converting of copper matte produces slag with high cuprous oxide content. The corrosion of chrome-magnesite refractories with slag of high cuprous oxide content is a major problem. Properties of olivine type of slag make the slag very attractive for matte smelting and converting.Analysis of phenomena determining the slag infiltration into the porosity of a refractory and dissolution of refractory components in the slag allowed for better understanding of the mechanisms of refractory destruction.The results of laboratory scale tests of the olivine slag infiltration into open porosity and corrosion showed dominating effects of slag temperature and cuprous oxide content. The optical and X-ray examination of slag samples permitted the definition of the mechanism of formation of new phases and refractory deterioration. 71"

Jan 1, 2009

By Mark Kruzynski, Srinivas Garimella, James T. Wiswall

"A flue gas recirculation (FGR) system for a combustion fired aluminum melting furnace is experimentally investigated. The FGR system flows combustion air in a turbulent jet within the flue gas stream, and the turbulent jet flow is collected in a tube at a distance from the jet exit. Entrainment of the flue gases as well as heat transfer between the flue gases and the jet occurs over the length of the exposed jet. Heat transfer between the flue gases and the jet, and the amount of flue gas entrained into the jet (derived from temperature, flow rate and oxygen fraction measurements) were measured as a function of nozzle exit velocity and the distance between the nozzle exit and collection tube. In addition to flue gas entrainment, a fuel savings of up to 7%, due to heat transfer over the length of the jet, was projected from the measurements obtained.IntroductionFlue gas recirculation can be applied to aluminum melting furnaces to control combustion temperature. When coupled with a device to improve furnace efficiency by recovering heat from the furnace exhaust, flue gas recirculation provides a control technique that is integral to achieving the goals of reducing fuel consumption, increasing product yield, increasing the longevity of infrastructure, and reducing pollutant emissions. In particular, combustion temperature control can help reduce reactivity of the products of combustion with the molten metal surface and furnace refractory materials. Combustion temperature control can also help improve the life of heat exchangers used to recover energy lost to the environment in the flue gases, and reduce NOx formation in the combustion process. Flue gas recirculation can also dilute oxygen used in oxy-fuel combustion to reduce reactivity.Flue gas recirculation has been used since the 1970s to control flame temperatures in the automotive industry [1-3] and has successfully reduced NOx emissions. Many different flue gas recirculation approaches for high temperature melting such as melting aluminum and glass have been patented since the 1980s [4-12]. There has also been academic interest to determine the fundamental performance characteristics of flue gas recirculation in high temperature furnaces and in combustion [13-15]."

Jan 1, 2014

By Michael Zinigrad

The quality of metallic materials depends on their composition and structure and these are determined by various physico-chemical and technological factors. To effectively prepare materials with required composition, structure and properties it is necessary to carry out a research in two parallel directions: Comprehensive analysis of thermodynamics, kinetics and mechanisms of the processes taking place at the solid-liquid-gaseous phase interface during welding processes and development of mathematical models of the specific welding technologies. We have developed unique method of mathematical modeling of phase interaction at high temperatures. This method allows us to build models taking into account the thermodynamic characteristics of the processes, the influence of the initial composition and temperature on the equilibrium state of the reactions, the kinetics of heterogeneous processes, the influence of the temperature, composition, hydrodynamic and thermal factors on the velocity of the chemical and diffusion processes. The model can be implemented in the optimization of various technological processes in welding, surfacing, casting as well as in manufacturing of steels and non-ferrous alloys, materials refining, alloying with special additives, removing of non-metallic inclusions.

Jan 1, 2003

By M. I. Kalashnikova

Results of investigations concerning precipitation of heavy non-ferrous metals from solutions using precipitators based on elemental sulphur and lime with gypsum transfer to a separate product are given.

Jan 1, 2003

By H. J. Roorda

With an increasing need to obtain metals by processing complex fine intergrown ores, the use of electron-optical techniques will become more important as a tool for mineralogical studies. Electron images enable a higher spacial resolution than can be obtained by optical microscopy and thus provide a powerful and necessary aid for the examination of small grains and finely locked particles. In this paper the mineralogy of Meggen ore was investigated. Both light-optical and electron-optical techniques were used to evaluate the mill feed and products of the concentrator. Detailed examination by reflected-light microscopy to assess the comportment of galena in the complex pyritic ore was inconclusive in establishing the cause for low lead recovery of only forty percent of the ore's lead content. Electron microprobe analyses indicated that the majority of the lead lost to the tailings was accounted for by extreme fine (often smaller than one micron) and complex intergrowths of galena in pyrite. The remainder was lost as fine free galena grains.

Jan 1, 1987

By S. L. Kher

The Singhbhum Copper Belt located in the state of Bihar in Eastern India bears evidence of ancient workings and indicates the existence of a civilized habitation in this region in the past. It was in 1833. how- ever, that the first official announcement of the occurrence of copper in the district was made. Although the occurrence was confirmed in 1847, it was not until 1857 that the first company was formed to exploit the deposits. This Company was dissolved in 1859 and from then until 1920, there were many unsuccessful attempts to develop and exploit the copper deposits in the Singhbhum area. In 1920. the Cordoba Copper Co. took an option on the Mosaboni area, which is nearly 10 km away from the present works located at Moubhandar, Ghatsila and exercising the option in 1924, purchased the mining rights from the Cape Copper Company. The Cordoba Copper Co. was then converted into Indian Copper Corporation Ltd. This was subsequently taken over by the Government of India in March 1972 and is now known as Indian Copper Complex (ICC), forming one of the two smelting units of Hindustan Copper Ltd.

Jan 1, 1976

By Hongxu Li, Pu Liu, Hao Bai, Daqiang Cang, Lihua Zhao

"Coal, as the main energy in ferrous metallurgy, is consumed on a large scale and great amount of CO2 is emitted likewise. In this paper, a model, based on carbon balance, was developed for CO2 emission analysis, with data obtained from a typical integrated steelworks in China. The result shows that, CO2 emissions increase almost constantly with the growth of steel production. However, coals of different classes and product variety in the steelworks exerted an influence on CO2 emissions. Furthermore, three scenarios, including natural gas instead of coal for power generation, EAF process partly replacing integrated steelmaking, and feasible techniques applied to achieve lowest process energy consumption (FLPEC), were assumed to seek possible ways of carbon emission reduction. The result proves that the second scenario is most effective. If 40% of the steel product could be from EAF process, CO2 emissions would be reduced by 45.07%.IntroductionGlobal warming has become a global environmental problem, which is generally caused by excessive emission of greenhouse gases, such as CO2, generated from human activities and industrial processes. It is estimated that about 7% of global CO2 emissions was from iron and steel industry. Further, if the ore and coal’s mining and transportation are included, the CO2 emissions would reach 10%[1]. In general, the relationship between energy saving and CO2 emission reduction is positive correlation. However, in iron and steel enterprises, due to different types of energy resources like coal, heavy oil, natural gas, the consumption of which will generate different amount of CO2, are used, different energy consumption structure in iron and steel enterprises will lead to difference of CO2 emissions.In order to assess the CO2 emission reduction potential of China’s steel industry, Ke Wang etc.[2] developed a model using LEAP software to generate 3 different CO2 emission scenarios for the industry from 2000 to 2030. LEAP is a scenario-based software tool for integrated energy-environment and greenhouse gas mitigation analysis. The amount of CO2 emissions was obtained by the following equation:"

Jan 1, 2011

By M Philip Schwarz

"This paper reviews the status of computational modelling of a variety of common metals reduction processes, namely the blast furnace, rotary kiln and fluidised bed, and one new process not yet commercialised, namely smelting-reduction as in the HIsmelt Process. In each case, the last decade has seen the emergence of the capability to simulate the processes using multi-phase reacting computational fluid dynamics techniques. In some cases this capability is still in the process of being developed, and the next few years will see the maturing of the modelling techniques. As they become established, it will be possible to apply them to further refine the older technologies such as blast furnaces and rotary kilns, and assist in the optimisation, commercialisation and acceptance of the newer technologies such as fluidised bed and molten bath reduction. The development of a computational fluid dynamic model of bath smelting-reduction is described in some detail to illustrate how a large number of complex and interacting phenomena can be successfully simulated within a CFD framework. IntroductionPyrometallurgical reduction processes, such as the iron blast furnace, have become increasing more sophisticated through the centuries, so that today they are often highly efficient. There are continuing pressures, however, to refine existing processes and develop new ones. The imperatives are often economic, given that the long-term trend in the price of metals is always downward. In recent times, there has been the additional need to improve the environmental impact of metal production. Given that they almost inevitably require the use of carbon, metal reduction processes are large sources of greenhouse gases, and even a relatively small improvement in efficiency can be valuable in reducing CO2 production. Local environmental issues, such as the need to control of particulate emissions, are also driving incremental improvements in equipment.In addition to the economic and environmental drivers mentioned above, new process development is also being driven by the need to process new ores, and the need to produce unrefined metal in a form more compatible with alternative routes for downstream processing. An example of the latter is the production of DR! (Direct Reduced Iron) as a feed for EAF Electric Arc Furnace) in mini-mills.Further improvement of processes that have already been honed by continual plant experimentation over many years is not an easy task. To deliver further gains in efficiency, throughput, or product quality requires a highly sophisticated tool: one such tool· is computational modelling."

Jan 1, 2001

By Supachai Surapunt

The distribution behavior of V A minor elements (As, Sb and Bi) in the smelting stage of the Mitsubishi process were evaluated thermodynamically based on thermodynamic data and operating data. The fractional distributions between the gas, slag and matte phases considered as the degree of vapor saturation of 1.0 are as follows: 53.8, 27.2 and 19% for As, 23.6, 56.6 and 19.8% for Sb, and 91.3, 1.1 and 7.6% for Bi, respectively. Arsenic is mostly distributed to the gas and slag phases. It is effectively eliminated by volatilizing and slagging. Antimony is mainly in the slag phase, which is suitably removed by slagging. Bismuth is easily vaporized to gas phase. The degree of vapor saturation has a large effeet on the distribution behaviors of the three elements between the three phases. The amount of a minor element in the charge has an effect on the distribution of As but no effect on the distributions of Sb and Bi. Increasing matte grade and temperature results in the change of distributions for As and Sb, significantly. The change in the distribution ratio between slag and matte phases also considerably affects the distributions of As and Sb. The distribution behavior of Bi is not significantly changed by the change in matte grade, temperature and distribution ratio.

Jan 1, 2003

By R. A. Roberti

Most copper refineries use conventional wheel systems to cast anodes. over a period of time the copper moulds that are used become warped and cracks develop. To control mould warpage, the mould's are either rejected after a certain warpage is reached, or the shape is restored by mechanical means. The cracks, unless they are very severe, are repaired by a peening process. Even with regular maintenance to control warpage and cracks, the moulds have a limited useful life. If warpage and cracks are not controlled, anode quality deteriorates and tankhouse operations are seriously affected. -An intensive study was initiated to develop means of controlling mould warpage which culminated in the d?evelopment of technology to control mould warpage to within ±1. 5 mm, and at the same time effectively contr0l: cracking and significantly increase the mould life-. The warpage control has been achieved by using a unique mould design. Mould cavities are present on both sides of the mould and periodic inverting controls the wa-rpage in the cavities. The mould casting procedure has been developed and all production wheels have been converted to the new mould design. The performance characteristics of these moulds will be detailed. 21

Jan 1, 1987

By Kevin L. Gering

A detection method and apparatus have been developed to perform real-time measurement of aqueous free cyanide, C-. A laboratory prototype can measure cyanide ranging from 5 micrograms ,per liter to 100 milligrams per ?liter for analysis times as short as 2 minutes per measurement. Sample size per measurement is typically only a few mI, thus? minimizing the waste volume produced from spent samples. The basis for this detection device is a quantifiable, stable affinity between the electrode material and free cyanide in the sample; The electrode exhibits piezoelectric behavior, allowing it to be used as a microbalance. This technology 'has experienced two generations of laboratory prototypes, and has been thoroughly tested to determine the operational sensitivity toward process variables such as pH, competing reactions, etc. The speed and ,accuracy of this method make it superior to conventional wet chemistry methods used for quantifying cyanide levels in water. A device based on this technology could be useful in areas involving process monitoring and environmental compliance, .particularly in the cyanide-based leach mining industry. Interest for this detector has been shown by the gold mining industry and others. Patent application is in progress.

Jan 1, 1998

By G. L. Peralta

Geothermal energy is an important source of power in more than 12 countries and is a potential source in 50 countries. However, the exploration and use of geothermal resources generate residues such as scale and sludge. The scale is from the steam distribution pipes while the sludge is from cooling ponds. These solids contain significant levels of elements which are of environmental importance notably, arsenic, sulfur, copper, zinc and lead that require safe treatment and disposal. The compositions, phases, textures, morphologies and size of scale and sludge particles have been studied by laser particle size analysis, light microscopy, scanning electron microscopy, X-ray microanalysis, and X-ray diffraction. In addition, their leachability was tested with protocol leaching procedures and sequential extractions. The detailed spatial relationships and speciation of the environmentally significant constituents have received particular emphasis. The information obtained is useful in understanding how the scale and sludge are formed, their leaching behavior if disposed of in a landfill and in developing appropriate treatment strategies.

Jan 1, 1994

By K. Fagerlund

Methods for simulation of settler reactions, matte-slag separation and matte settling in copper flash smelting have been examined. The reaction, separation and settling phenomena of slightly oxidized chalcopyrite samples and cuprous sulfide-magnetite mixtures in fayalite type slags were examined at about 1300°C under inert atmosphere. Two methods based on introduction of molten samples of oxidized chalcopyrite concentrates or synthetic matte-magnetite mixtures onto the surface of molten iron silicate slag were tested. In the first method the samples were water quenched and polished specimens were studied and analysed using light optical microscope, scanning electron microscope, energy dispersive spectrometer. In the second method processes taking place after the introduction of samples onto the slag are followed "in situ" using X-ray transmission image monitoring. Great differences were observed in separation and settling behaviour of low and high grade copper mattes produced as a results of interaction of initial samples and slag.

Jan 1, 1997

By W. Kasprzak

Modern light metals processing technologies are very complex and involve a diverse set of variables that must be quantitatively evaluated. The most effective way to design new casting processes that deliver specified metallurgical and mechanical properties is to develop a method of simulating the "real-time" process within a test sample of sufficient size. The results can then be analyzed and the required optimizations can be performed. This paper presents a novel method of simulating the industrial casting processes in a laboratory environment using an experimental apparatus based on the principle of high frequency induction heating. The applicability and accuracy of the proposed analytical method is demonstrated, for example, by simulation of the solidification and heat treatment of a test sample composed of two dissimilar materials. The simulation can be used to develop a stress model for an engine block made from an aluminum based alloy with iron cylinder liner inserts.

Jan 1, 2002