Search Documents

By F. Michael Hosking

Modeling of a furnace brazing process is described. The computational tools predict the thermal response of loaded hardware in a hydrogen brazing furnace to programmed furnace profiles. Experiments were conducted to validate the model and resolve computational uncertainties. The results from selected furnace simulations and measured thermal events were compared. Critical boundary conditions that affect materials and processing response to the furnace environment were determined. "Global" and local issues (i.e., at the furnace/hardware and joint levels, respectively) are discussed. The ability to accurately simulate and control furnace conditions is examined.

Jan 1, 1998

By Seiji Yokoyama

As a series of fundamental study on the gas evaporation method, a levitation-melted aluminum was evaporated in the gas mixture of argon and ammonia to synthesize ultrafine particles of aluminum nitride. When the ammonia partial pressure were more than 2kPa, the formation ratio of aluminum nitride was about 95%. The particles of aluminum nitride were mainly hexagonal. The mean size of the particles of aluminum nitride was about 57 nm, and it was constant without depending on the temperature of the levitated aluminum and the partial pressure pf ammonia. The aluminum nitride was formed by the reaction between ammonia and condensed liquid aluminum particle whose size was relatively small.

Jan 1, 2006

By Ricardo Ponce

In recent years, ENAMI implemented modernisation plans at its two smelters in order to meet the government's environmental regulations introduced in the early 1990s. The modernisation plans defined the new SO2 and particulates emission targets, deadlines for compliance, and the revised treatment capacities of the smelters. At Las Ventanas smelter, the principal process change consisted of eliminating the reverberatory furnace. All the smelter feed is currently processed in a 4m diameter, 14m long Teniente Converter, using up to 34% oxygen enriched air. Dry concentrate is injected into the bath through tuyeres. A fuel oil burner compensates for any process heat deficiency. The Teniente Converter high copper content slag is cleaned in an electric furnace. This furnace is also used to melt internal reverts. This paper will discuss the successful operation of the slag cleaning electric furnace.

Jan 1, 1999

By Du Sichen

The present paper presents the modeling of gas-solid reactions in the case of the decomposition of CaCO3, describing the reaction kinetics on the basis of heat-transfer concepts which could be compared with thermogravimetric results. In the case of solid-solid reactions, the present paper describes the model developed for describing solid-solid reactions from dynamic X-ray diffraction technique, developed by the present team. The model has been successful in explaining the formation of spinel from MgO and Al2O3.

Jan 1, 2006

By Joel K. Witt

San Manuel Oxide operations of BHP Copper, located in Southeastern Arizona, operates a leach-solvent extraction/electrowinning (SXEW) facility that produces high quality cathode copper from low-grade oxide ores. Permanent heap leaching and in-situ leaching methods accomplish the dissolution of copper from the oxide ores. Open pit mining and heap leach construction took place from 1985 to 1995. Run-of-mine oxide ore from the pit was hauled to the heap dumps and leached by the soaking cure and continuous irrigation method. Solution application to the heaps still continues and acid soluble copper recovery has reached 86%. This paper presents and discusses the current operating practices and innovations applied to the leach facilities to maximize copper recovery from the heap leached residue. Factors such as irrigation methods, solution chemistry, sideslope treatment, post curing, lixiviant acid strength, and "rice paddies" irrigation, will be discussed. Heap leach solution control and sampling methodologies will be also presented.

Jan 1, 1999

By P. K. Narasimhargahavan

This paper discusses briefly the major reasons associated with the growth and its impact on the energy requirement and Environmental imbalance. A projection based on the present global Alumina and Al requirement indicate a substantial further growth of at least 30% over the next 10 years. It is indicated that the main factors which are likely to influence investments are the environmental factors such as the Climate Change and global response to the growing energy prices and sustainable development. Each of the developed / developing nations must find response to the GHG emissions which will encourage the Al Industry to make an effective contribution to global warming while preserving the international competitiveness of the industry - a challenging task. The efforts shall concentrate on improving energy efficiency in the industry possibly of the order of 25% over the next 10 to 20 years. The developments in this line are discussed.

Jan 1, 2010

By Ko-ichiro Ohno

It is recently recognized that the iron reduction and melting as well as the slag separation of a composite of granular iron ore and coal are completed in a very short period of about IO minutes when the composite is rapidly heated up to approximately 1673K. These phenomena are expected to be applied to a new iron-making process. The mechanism of iron ore reduction and iron-slag separation during rapid heating has not yet been revealed and the fundamental research has just started. Carburization of the reduced iron is regarded as one of the most important steps in this process. In the present work, the composite was prepared from four kinds of coal or graphite as a carbon source and electrolytic iron powder as a completely reduced iron ore. The temperature at which the liquid formation and iron carburization occurred was monitored. Direct observation of smelting reduction behavior was made by a confocal laser-scanning microscope combined with the infrared image-heating furnace to clarify the effect of molten ash on iron carburization. It was found that the meltdown temperature of composite became lower as the melting temperature of coal ash decreased. From the observed result, it was presumed that the liquid slag would act as an important media for the carbon transfer from coal to iron. The carburization mechanism during the smelting reduction was estimated as follows. When slag containing iron oxide melted down and contacted carbon, iron oxide in the slag was reduced and the formation of the metallic iron particle as well as the its carburization occurred simultaneously at the slag-carbon interface. Carburized iron particle was carried from slag- carbon to slag-iron interfaces due to the slag convection flow caused by the difference of the interfacial tension between the carbon-slag and iron-slag interfaces. Carburization of reduced iron could proceed with a repeat of the above-mentioned process.

Jan 1, 2003

By C. Schwandt

Recent research work has led to the development of a new electrochemical hydrogen sensor, which is based on a proton conducting solid electrolyte in conjunction with a self-contained solid hydrogen reference standard and is operated at elevated temperatures. The incorporation of the internal hydrogen reference renders the sensor versatile and user-friendly and makes it attractive for practical exploitation. The present article focuses on the utilisation of the sensor as the integral part of a probe for the quantitative determination of hydrogen in molten aluminium and aluminium alloys. The main features of the sensor and the probe as well as the measuring technique are discussed. Experimental results obtained with the novel analyser in trials under industrial conditions are presented and highlight the good performance of the device.

Jan 1, 2003

By R. I. Rodriguez

Since the 1973 energy crisis, high fuel oil costs have been eroding the economics of the Nicaro and Punta Gorda Plants that employ the Caron Process for laterites processing. Since 1995, Cuban crude oil production has growth dramatically, with progressive utilization in power generation, cement and nickel plants. This paper shows how Nicaro and Punta Gorda plants have been able to shift from expensive Bunker C Fuel Oil to heavy but cheaper Cuban Crude Oil of high Sulfur content and achieve a significant reduction in operating cost. Problems related to the high sulfur content of the Cuban crude oil have demanded extensive investigations of the process chemistry and novelty solutions are proposed, with corresponding changes in process conditions. Innovative options are shown that will allow further cost reductions in the future. Keywords: Cuban Crude Oil, Sulfur, Ammonia.

Jan 1, 2004

By Qingcai Liu

The effect of the TiC addition on corrosion resistance of the Al2O3-C refractories in smelting reduction melts has been studied by quasi-station immersion and rotary immersion. The corrosion rate of Al2O3-C refractories is decreased with the TiC addition. The corrosion mechanism of Al2O3-C refractories is oxidization of graphite carbon by the oxides of the melts and the formation of deteriorate layer.

Jan 1, 2006

By Dale T. Peters

In the United States, the United Kingdom and numerous other countries, copper has long been the plumbing material of choice. This has been the case since the late 1920s in the United States and since World War II in the United Kingdom. However, in recent years the plumbing tube market has caught the eye of the chemical industry, and several plastic resins have been introduced to the marketplace as substitutes for copper in household plumbing systems. One of these, polybutylene tube, had so many failures in the United States that a class action law suit was filed, and the manufactures of this product were forced to create a trust fund of nearly one billion dollars to repair damages caused by their product. Chlorinated polyvinylchloride (CPVC), in rigid pipe form, on the other hand, has been mechanically acceptable albeit its recent introduction precludes the test of time enjoyed by copper tube in this application. This paper reviews the State of California's portrayal of copper's environmental effects and will be largely based on the data and information assembled by the Copper Development Association Inc. in its presentation to the State of California in August, 1998 in response to the State's Draft Environmental Impact Report for Chlorinated Polyvinyl Chloride (CVPC) Pipe for Use for Potable Water Piping in Residential Buildings. The paper is intended for use as a model for the use of other copper organizations and individuals in responding to similar situations.

Jan 1, 1999

By Ahmad Umar

A variety of ZnO nanostructures such as sea-urchin-like structures composed of nanowires and nanorods, nanocombs, nano/micro spheres and cages, star-shaped ZnO nanostructures, flower-shaped nanostructures, needle-like nanostructures etc. have been synthesized applying two different fabrication techniques i.e. thermal evaporation and cyclic feeding chemical vapor deposition techniques at different reaction parameters such as reaction temperature, growth period, reactant concentrations, types of source material and substrates etc. It was observed from the experiments that the morphologies of the grown structures were highly influenced by the reaction parameters and fabrication techniques and specific morphology can be obtained at particular reaction parameters in a specific synthetic procedure. Extensive morphological investigations of the obtained products demonstrate that the grown structures are single crystalline and having a wurtzite hexagonal phase. Room-temperature photoluminescence spectra of all the deposited products exhibited good optical properties. Finally, the growth process of the fabricated structures were proposed and discussed in detail.

Jan 1, 2006

By Dieter Offenthaler

Catalysts used in petroleum industry often contain valuable amounts of PGMs. The typical recycling route for those materials is the pyrometallurgical one, but this treatment way offers limited flexibility with respect to small charge weights. A new process, combining a pyrometallurgical pre-treatment step of the ceramic carriers with a hydrometallurgical leaching procedure overcomes this disadvantage. It not only allows the economical treatment of even very small charge weights, but also gives the possibility to maximize the PGM yield by individually adapting the process to the different charge materials. Due to an ingenious process design, where all leaching agents and effluents are recycled in a closed loop and therefore no waste waters leave the process, process operation becomes very economical. However, the temperature-time-regime in the pyrometallurgical pre-treatment step is of major importance for the success of the whole process. Therefore various investigations have been done to identify how the different process variables in the pyrometallurgical pre-treatment influence the subsequent leaching procedure. It turned out, that the adjustment of the correct phase-modification in the ceramic carrier materials during the pyrometallurgical treatment is the key factor of this process step. Although it is a troublesome issue to exactly adjust the correct phase modifications, it is the prerequisite to take advantage of the benefits of this new process concept.

Jan 1, 2006

By Akira Yazawa, Kazuo Koike, Mitsuhisa Hino

"The vapor pressures of MS (PbS, SnS and Sb2S3) in the molten Cu2S-MS, FeS-MS pseudo-binary and Cu2S-FeS-MS ternary systems were measured by means of a transportation method in the temperature range of 1323 and 1423K to calculate MS activities in the sulfide melts. The activities of MS in these systems show negative deviation from ideal behavior except the FeS binary systems which exhibit nearly ideal behavior in the homogeneous melts. The activities of the Cu2S-FeS pseudobinary system, which is fundamentals of the copper matte, were estimated from the activity values in the ternary systems and exhibit negative deviation from ideality.The distribution behavior of tin between the ·matte and silica saturated fayalite slag was investigated under the controlled partial pressures of S02 at l 523K. It was found that, in general, tin is distributed in the both phase, while tin is concentrated to the slag phase with increasing copper content in the matte. The activity coefficient of SnO in the slag was calculated based on the distribution ratio combined with the activity coefficient in the Cu2S-FeS system.IntroductionThe thermodynamic properties related to the Cu2S-FeS system and the Cu2S-FeS-MS systems (where MS can be PbS, SnS, Sb2S3, As2S3, Bi2S3, etc.) is required to be better understanding of the copper smelting process. However, thermodynamic analysis such as the distribution of impurities among the gas, slag and matte phases is difficult due to lack of thermodynamic data. In this study, the vapor pressures of MS (PbS, SnS and Sb2S3) in the Cu2S-MS, FeS-MS. and Cu2S-FeS-MS systems were measured by a transportation method. The distribution behavior of tin between the matte and silica saturated fayalite slag was also investigated. The results in the present experiments are useful to analyze thermodynamically the behavior of component in the copper matte smelting."

Jan 1, 2000

By Ian F. Hughes

"Concepts of an integrated steel plant for sheet products to be built and operating in the year 2000 will be described. The design and operating methodology of this market driven facility will integrate process uniqueness, standardization, manufacturing automation, artificial intelligence and information flow.An integrated steel plant for the year 2000 is defined for this article as one that will be built on a greenfield site and ""started up"" in the year 2000 with a capacity of three million tons per year of flat rolled products ranging from cold rolled and electrical steels to high strength formable steels and a full range of coated products.It may seem that the 21st century and the steel plant we're discussing are far into the future. The startling truth, however, is quite the opposite. As shown in Figure 1, even with accelerated development, a new process on which laboratory development work is begun today might just barely pass through the laboratory phase, pilot plant, and commercial feasibility stages such that it can be considered viable for construction and start up in the year 2000.On that basis, it is very unlikely that this 21st century steel plant will utilize any technology that isn't at least under investigation in the laboratory in 1988. As a result, we recognize that planning and selecting the facilities for this plant is, in fact, a pragmatic rather than futuristic process, and that its main value is in providing a bridge to longer-term predictions."

Jan 1, 1988

By S. Yabe

The reinforcement of the annual copper production capacity to 330,000 metric tons has been attained at Saganoseki Smelter & Refinery in 1991, which is one of the largest and most efficient custom smelters in the world. Many operational improvements and technology developments have realized the increase of smelting and refining capacity without adding main facilities to the existing process. The blister copper refining and anode casting process is composed of two 400 tonnes anode furnaces and one double-wheeled casting machine with the capacity of 80 tonnes per hour. The great innovations in this process such as the finding of essential issue on the extending of anode-mould life and the development of a new anode-mould casting machine have raised the operation efficiency by 14% Now, the process is producing 38,500 tonnes per month of best quality anode in well- controlled working condition, and anode productivity per worker increased by 52%. The progress in extending anode-mould life, the mechanism of the new anode-mould casting machine and the increase of efficiency in butane reduction, that were the principal parts of many technological improvements, are described in the present paper, including some operation results.

Jan 1, 1993

By Entov Vladimir M., Gilmer R. Burgos, Andreas N. Alexandrou

"Processing of metal alloys in their mushy state represents a new trend in metal processing. As part of this process, known also as thixocasting, a specially prepared slurry at a temperature in the mushy region is injected into a die. Parts produced using this technology offer better mechanical properties than those produced by casting, and comparable to those of forged alloys.In thixocasting, semisolid slurries are highly concentrated suspensions of rounded rosette-like crystals in eutectic liquid. The mechanical behavior of the slurry is determined by the structure and properties of the skeleton formed by the alpha phase particles. The skeleton structure is almost never at equilibrium, and its evolution is, governed by a number of kinetic phenomena of different c11'aracteristic time-scales. Therefore, the skeleton structure depends on the mechanical and thermal history of the material. As a result of these kinetic processes, the rheological properties of the material, such as effective viscosity and yield stress, decrease with structure breakdown, and increase with its development. In the present investigation, the behavior of semisolid slurries during processing is modeled using the conservation equations, and a Herschel-Bulkley fluid model. The rheological parameters are assumed to be functions of the solid volume fraction, and of a structural parameter that changes with processing history. The evolution of the structural parameter is described by a first order kinetic differential equation that relates the rate of build-up and break-down of the solid"

Jan 1, 2000

By J. Smuts

The mixed-valence iron silicate ISCORITE (Fe7Si010) was identified recently in a number of ironmakingmater1als, some of which were first produced more than a century ago. Although the existence of iscorite was not reported before 1967 and published phase diagrams do not make provision for it, the morphology of the phase in all the materials that were examined suggests that it is stable under a variety of conditions. It is shown that is-corite can accommodate various foreign cations in its lattice where they can replace Fe and/or Si. The morphology of is-corite in a number of materials of different origin is shown in relation to iron oxides and silicates in optical and SEM/BSE images.

Jan 1, 1991

By G. Upadhya

Considerable success has been achieved recently in modeling microstructural evolution during solidification of castings bthrough the coupling of macroscopic heat transfer with microscopic solidification kinetics models. However, a complete model for simulation of solidification in complex shaped castings involves: (i) the description of fluid flow, during and after mold filling, coupled with (ii) heat transfer to the mold and surroundings by use of a macro model, followed by (iii) a description of subsequent solidification of liquid metal by use of a micro model for solidification of the alloy under consideration. This paper describes the coupling of solidification kinetics model to a 3D, transient, fully coupled fluid flow and heat transfer model. Coupling between the macremicro models is achieved by using the latent heat method. Micro models for the eutectics of gray, white and ductile iron are discussed. This coupled code has been used for predicting the thermal history and microstructural data for shaped castings. Various applications of the model, including prediction of shrinkage defects, grain density contours, and graylwhite transition region in the casting, are presented for a relatively complex casting geometry.

Jan 1, 1992

By N. Verbaan, E. Bourricaudy, M. Dry

"Starfield Resources is developing a novel circuit for the recovery of nickel, copper, cobalt, iron oxide, sulphuric acid and precious metals from the Ferguson Lake deposit in Nunavut, Canada. In this deposit, pentlandite is too finely disseminated in pyrrhotite for the production of a smelter-grade nickel concentrate at an acceptable nickel recovery, so established technology is not applicable and a novel chloride-based circuit is under development. The enabling aspect of this circuit is the hydrolysis of ferric chloride to hematite, releasing gaseous hydrochloric acid that is recycled. Conventional steps are used for separating and recovering the valuable metals from the chloride solution generated. This paper briefly outlines the circuit and presents the results of experimental work on the enabling steps, viz. the oxidation and hydrolysis of iron chloride to hematite and gaseous hydrochloric acid.IntroductionThe Ferguson Lake bulk sulphide ore body in Nunavut, Canada, owned by Starfield Resources Inc., contains significant amounts of base and precious metals but its mineralogy is such that it is not amenable to conventional processing. Pentlandite, for example, is too finely disseminated in pyrhhotite for even modem techniques such as fine grinding and improved flotation reagents to be effective [ 1] and extracting the value requires processing the entire bulk sulphide, including the pyrrhotite. To give the project a total green footprint, in terms of both carbon emissions and acid rock drainage, Starfield imposed the following requirements:• No reactive tailings to generate acid rock drainage.• No gaseous emissions other than normal atmospheric constituents.• No liquid effluents.• No regular consumption of fossil fuel.• High recoveries of all the valuable metals."

Jan 1, 2011