Search Documents

By Jilai Xue

Experiments with various industrial cathodes ranging from 35 wt.% to 100 wt.% graphitic and fully graphitized carbons were carried out in a laboratory aluminum electrolysis cell. Sodium and cryolite bath penetration into the cathode samples was measured by XRD and SEM-EDS analysis. For a higher cryolite ratio in the bath, the cathodes with lower graphitic carbons exhibited more sodium penetration than the fully graphitized. The increased graphitization in the cathode materials can reduce Na, NaF and Na3AlF6 penetration. SEM-EDS inspection reveals that the sodium and fluorides penetration within the cathode samples has different patterns for varying graphitization of the carbon materials. XRD quantitative analysis indicates that there is a large percentage of Na3AlF6 in the penetrated bath. The results can provide useful information for quality evaluation of the industrial cathode products.

Jan 1, 2010

By A. Barba, M. P. Gómez, F. Puertas, M. Palacios, M. F. Gazulla, S. Martínez-Ramírez, I. García-Díaz

"The present study explores the reactivity and burnability of cement raw mixes containing fired red or white ceramic tile wastes or combinations of the two as alternative raw materials. The results showed that the new raw mixes containing these wastes are technically viable. The reactivity and burnability of the new raw mixes have been evaluated; confirming very good results when the particle size of wastes was less than 90 µm. The chemical and mineralogical compositions of the new clinkers were comparable to clinker manufactured with conventional raw materials. The mix of red and white ceramic tile waste was found to perform as well or better than each type of waste separately, a promising indication that separation of the two would be unnecessary for these purposes.IntroductionPortland cement clinker production consumes large amounts of energy (850 kcal/kg clinker) and has a considerable environmental impact. This involves massive quarrying for raw materials (limestone, clay etc), as it takes 1.7 tonnes to produce one tonne of clinker, as well as the emission of greenhouse and other gases (NOx, SO2, CO2) into the atmosphere. Around 850 kg of CO2 are emitted per tonne of clinker produced.The cement industry is looking for solutions to these problems, to attain sustainability and comply with the Kyoto Protocol commitments [1,2]. For that reason, experimental ways are being explored to develop cements whose manufacture is less energy-intensive, less damaging to the surrounding environment and with lower tendency to emit polluting gas. One of the reach this objective is the use of industrial waste and by-products as alternative materials for cement manufacture. Such alternative materials may partially replace fuel [3,4], conventional raw materials [5-8] or clinker in the final composition of the cement [9]."

Jan 1, 2008

By J. C. Pandey

The paper highlights the experimental investigations to characterize texture and plastic strain ratio r-Bar in auto grade steel sheets by ultrasonic measurements, whereas attempts were made to characterize interlamellar spacings in pearlite, tensile stresses and torsional properties in prestressed concrete wires by eddy current measurements. Good correlations were obtained between the testing parameters (such as ultrasonic attenuation and velocity in case of steel sheets as well as eddy current out put voltage and phase angle in case of steel wires) and the materials properties (such as texture, plastic strain ratio r-Bar, interlamellar spacings in pearlite, tensile stresses and torsional properties). 15 MHz normal direct contact and 20 MHz delay line normal shear wave probes were used for ultrasonic measurements. Eddy current measurements were done using an absolute coil probe with variable frequency selection. The experimental results show the possibility of nondestructive on line measurement of the above microstructures and properties.

Jan 1, 2010

By V. Kamavaram

Keywords: Recycling, Aluminum Metal Matrix Composite, Ionic Liquids, BMIC Recycling of aluminum metal matrix composites (MMC) via electrolysis in ionic liquids at near room temperature was investigated. The electrolytic melt comprised of 1-butyl-3-methylimidazolium chloride (BMIC) and anhydrous AlCl3. Impure aluminum composite (Duralcan MMC Al-380, 20 vol % SiC) was electrochemically dissolved at the anode and pure aluminum (>98%) was deposited on a copper cathode. The deposits were characterized by scanning electron microscope, X-ray diffractrometer, and mass spectrometer. The influence of various process parameters such as concentration of electrolyte, and applied cell voltage on the recycling process was studied. The recycling process yielded current densities in the range of 200-500 A/m2, and cathode current efficiency of about 85%. The results indicated that impurities such as Cu, Si, Ni, Fe, Mg, Mn, and SiC particles were removed as anode residue. Energy consumption of about 3.7-6.3 kWh/kg-Al was obtained at a cell voltage of 1.0-2.0 V and cell temperature of 100 ± 5°C. Low energy consumption and no emission of pollutants are the two main advantages of this process compared to present recycling processes.

Jan 1, 2005

By Jilai Xue

Oxygen gas bubbles generate on anode during Pb electro-deposition process in PbSiF6-H2SiF6 aqueous solutions at room temperature. Cell voltage varies as the bubbles formed on the anodes surface. The bubble layer on the anode makes a voltage drop that consumes energy in the Pb process, which can be reduced by applying ultrasound on the anode. The effects of ultrasound frequency and anodic current density were investigated with ultrasound on and off, alternatively during the Pb electrode-position process. The removing of the gas bubbles were recorded in association with a drop in the cell voltage. The cell voltage can be lowered by 4% - 6% with ultrasound, which has potential for energy saving in Pb production.

Jan 1, 2010

By Yunnen Chen

In the present study, waste materials like pine sawdust and spent grains were investigated to assess their potential for removal of cobalt ion from water by the process of biosorption. The effects of solution pH, reaction time and initial concentration were studied in batch experiments. The removal efficiency of Co(? ) by spent grains was higher than that of pine sawdust. The initial removal was rapid and equilibrium was established in less than 90 min. Equilibrium data all agreed well with both Langmuir and Freundlich isotherm models for the two metal-biomass sorption processes. Good correlation coefficients were obtained for the pseudo second-order kinetic model. Pine sawdust and spent grains were shown to be promising biosorbents for Co(? ) removal from aqueous solutions.

Jan 1, 2010

By Linda Gaines

Use of vehicles with electric drive, which could reduce our oil dependence, will depend on lithium-ion batteries. But is there enough lithium? Will we need to import it from a new cartel? Are there other materials with supply constraints? We project the maximum demand for lithium and other materials if electric-drive vehicles expanded their market share rapidly, estimating material demand per vehicle for four battery chemistries. Total demand for the United States is based on market shares from an Argonne scenario that reflects high demand for electric-drive vehicles, and total demand for the rest of the world is based on a similar International Energy Agency scenario. Total material demand is then compared to estimates of production and reserves, and the quantity that could be recovered by recycling, to evaluate the adequacy of supply. We also identify producing countries to examine potential dependencies on unstable regions or future cartels.

Jan 1, 2010

By Dale W. Collins

The disposal of arsenic from copper operations possess various health, environmental and processing problems. There are basically two areas of concern. The first being the disposal or treatment of smelter flue dusts and the second the removal of arsenic from refinery electrolytes. A number of treatment options have been proposed including the addition of soluble arsenic wastes to copper heap and dump leaching solutions. This approach will allow arsenic to be reintroduced to the ore via Solvent Extraction (SX) raffinate associated with hydrometallurgical operations. Knowledge of the attenuation behavior and mechanism during leaching is important in determining the long term stability of arsenic and the success of this approach. Parameters, such as uptake capacity, pH, particle size and solution chemistry have been investigated. Arsenic attenuation has been examined using column leaching with experiments employing both continuous flow and pulsed additions of As(V). In the initial stages of leaching, the attenuation of arsenic appears to depend on the pH and iron concentration in the effluent. Arsenic stability in the copper oxide ore has been examined with rinses of progressively lower pH.

Jan 1, 1994

By Godwin Beene

During recent years, copper and acid production from Nkana Smelter has formed a significant proportion of ZCCM's total output, but a number of problems affecting the smelter over the last decade have only been recently overcome. This paper discusses recent developments in the smelting practice, highlighting some of the operational problems experienced and associated solutions. The smelter performance over the decade is discussed and the innovations in the smelting technology employed to sustain production in the wake of limited re-capitalization are dealt with in detail.

Jan 1, 1999

By Raj P. Singh Gaur

Due to high concentration of NaOH in the digested slurry after scheelite digestion, it is diluted to about 4N before filtration to separate sodium tungstate solution from the sludge (residue). However, in practice there may be deviations in the normality of NaOH present in the slurry. There may also be variations in the temperature of the slurry and filtration time. Slight variations in these parameters could cause tungsten losses in the sludge via the back reaction: Ca(OH)2 + Na2WO4? CaWO4 + 2NaOH This paper pertains to the effect of normality, temperature and time on the tungsten losses in the sludge that is separated from ?diluted-scheelite-slurry-in-NaOH? via filtration. Results indicated that tungsten losses in the filtered residue (sludge) were quite significant when the slurry temperature was kept at 70°C or higher. The effect of high temperature was less significant at the slurry normality of 3.6 or higher. Combination of low slurry normality (<3.6) and high temperature (>60°C) resulted into large W-losses in the sludge.

Jan 1, 2006

By A. Krishnan

Keywords: Tantalum extraction, SOM Technology, inert anode, membrane stability The Solid Oxide Oxygen Ion conducting Membrane (SOM) technology offers great potential for environment friendly and energy efficient extraction of high-energy content metals. This work was performed to demonstrate the technical and commercial viability of the technology to produce tantalum metal directly from tantalum oxide and ore concentrates using a solid-oxide, oxygen-ion-conducting membrane (SOM). The process can be used to efficiently produce tantalum metal without expensive pre-processing of raw materials and without harmful by products. The work reported in this paper is: the proof that high purity tantalum metal can be produced, study of the electrochemical behavior of the cell and the method to increase membrane stability.

Jan 1, 2005

By Patrick R. Taylor

A non-transferred arc thermal plasma assisted cyclone reactor has been designed, built and operated to evaluate its use in vitrification of wastes. Simulated waste (liquid, slurry or fine particulate) is injected near the plasma flame, where nearly instantaneous dehydration and calcination reactions happen. A non-transferred arc plasma torch was attached tangentially to the cyclone and is utilized as both an enthalpy source and to provide the gas velocities required to generate the cyclonic gas flow patterns. The closed top cyclone flow sends the solid particulates to the wall, where they are captured by a thin film of molten glass that is injected as a powder at a position lower in the reactor. The molten glass is then collected in a crucible. The feasibility of simulant injection directly into the flame zone and its effect on electrode lifetimes has been studied. Several candidate refractory systems have been evaluated for their suitability for extended use under the demanding conditions present in the cyclone reactor.

Jan 1, 2002

By Regina Maria Pinheiro

This work has for objectives to characterize a waste generated in the form of sludge during the treatment of the effluent of a paper making industry and to evaluate the effect of its incorporation in the amount of 10 wt.% on the properties and microstructure of a clayey body used for brick production. For the characterization of the waste the following techniques were used: X-ray diffraction, X-ray fluorescence, differential thermal analysis and termogravimetric analysis. Incorporated bricks were produced in industrial scale before firing at 750°C in a Modified Caieira type furnace. The physical and mechanical properties evaluated were water absorption and compression strength. The microstructure of the fired ceramic was evaluated by optical microscopy. The environmental evaluation was made by solution test and atmospheric emission by monitoring the release of SO2, NOx and particulate material. The results showed that, in agreement with the characteristics of the waste, its recycling into red ceramic can contribute to decrease the consumption of fuel during the firing stage. The properties of the fired ceramic attend the norms. With respect to the environmental aspect, the incorporation of the waste did not impact the environment.

Jan 1, 2009

By Karel Van Acker

The automotive is a sector where energy consumption during the use phase prevails over the production and the end-of-life phase. Therefore, a lot of research and innovations at replacing classical steel parts by lighter materials like light metals and polymer composites. While composites are very attractive for the use phase of cars, their introduction suffers from the limited end-of-life options for composite structures. An extensive life cycle analysis for a reference car design has been conducted to study the effects of replacement of conventional steel structures by lightweight carbon fibre composite alternatives. The study also takes second order effects in the design of the car into account. The opportunities and treats of the trend towards more intensive use of carbon-fibre composites in car design are identified. A discussion on the potential of other types of composites for the automotive in terms of sustainability considerations is added.

Jan 1, 2010

By Hans Korfmacher

Product take-back regulations implemented in Europe have presented significant challenges to the consumer electronic product and battery industries. Initially companies established single compliance organizations within individual Member States. These programs met business needs but were inefficient and costly. They were protected from pressures of marketplace competition and could not leverage economies of scale. In order to address these problems P&G, Hewlett Packard, Sony and Electrolux conceived a pan-European compliance organization to collect waste electronic equipment Europe-wide. This organization, called the European Recycling Platform (ERP), operates in competition with existing national compliance systems. Since 2005 ERP has collected 800,000+ tons of waste electronic products and delivered millions of dollars in cost savings. This presentation reviews the steps needed to establish successful competitive collection organizations that provide sustainable recycling at the lowest cost.

Jan 1, 2010

By Shadia J. Ikhmayies

The SnO2/CdS/CdTe thin film solar cells were fabricated on glass substrates by using the spray pyrolysis (SP) technique for the deposition of the SnO2 and CdS layers and vacuum evaporation for the CdTe layer. The transmittance curves were used to investigate the interdiffusion in the two interfacial regions SnO2/CdS and CdS/CdTe by taking the first derivative of the absorbance as a function of wavelength. The appearance of new bandgaps around the bandgaps of SnO2:F, CdS:In and CdTe layers is a strong evidence on the interdiffusion in the two interfacial regions and/or the formation of quantum dots.

Jan 1, 2010

By Jewel A. G. Gomes

Electrocoagulation (EC) has been performed with Al-Fe electrode system with changing polarity for the removal of arsenic from water. The removal process has been studied using ICP-AES and Anodic Stripping Voltammetry with a wide range of arsenic concentration (1-1000 ppm) at various pH (4-10) and residence times (1-60 min). Electrochemically generated by-products have been analyzed using XRD, FTIR, XPS, SEM/EDS and Mössbauer Spectroscopy. Results revealed expected crystalline iron oxides (magnetite (Fe3O4), lepidocrocite (FeO(OH)), iron oxide (FeO)) and aluminum oxides (bayerite (Al(OH)3), diaspore (AlO(OH)), mansfieldite (AlAsO4?2(H2O)), as well as some interaction between the phases. The amorphous or ultra-fine particular phase was also found in the floc. The substitution of Fe3+ ions by Al3+ ions in the solid surface has been observed, indicating an alternative removal mechanism of arsenic in these metal hydroxides and oxyhydroxides by providing larger surface area for arsenic adsorption via retarding the crystalline formation of iron oxides.

Jan 1, 2006

By A. E. M. Warner

At the Copper Cliff Smelter, Inco Limited has extensive experience in converting primary smelting mattes over a broad range of nickel/copper ratios and compositions. In the past 35 years, technology developments at Inco have reduced the number of Peirce-Smith converters in Nickel/ Bulk (nickel-copper matte) service from 13 to the current 5. This paper will discuss: ? The performance and life of ?stretch? 13.7m shells versus conventional 10.7m converters. ? Process control and information system development from the early 1980?s to view converter aisle status on a continuous basis to the recent central control of the stretch shells. ? Nitrogen cooling of finishing matte from plant testing to implementation in the early 1990?s to replace the dedicated cooling converters. ? The impact on converting of changing the smelter flowsheet in the early 1990?s. ? A current program to develop a converting strategy for the future to address environmental issues and profitability.

Jan 1, 2005

By Sergio Neves Monteiro

In the present work, a ceramic foam elaborated with illitic clays was characterized. Properties related to density and compression strength were determined in samples fired at 1300oC, a temperature that permits the clay structure to generate and retain gases that will produce the foamy structure. The microstructure of the ceramic foam was studied by X-ray diffraction, scanning electron microscopy and mercury porosimetry. The results showed that the ceramic foam presents a bulk density of 0.38 g/cm3. The microstructure is formed by large open pores, quartz particles and vitreous phase.

Jan 1, 2006

By Shadia J. Ikhmayies

Nanocrystalline CdS:In thin films with particle size in the range (3-36 nm) were produced by the spray pyrolysis technique on glass substrates. The films were characterized by investigating their X-ray diffractograms (XRD), scanning electron microscope images (SEM), transmittance curves and photoluminescence (PL) spectra. The size of the nanocrystallites was estimated from XRD difractograms and then from the hyperbolic band model and the bandgap energies of the nano- particles, which were calculated from the positions of the minima in the first derivative curve of the absorbance. Fine-structured PL spectra confirmed the nanocrystalline nature of the films.

Jan 1, 2010