Search Documents

By G. J. Abbaschian, A. B. Gokhale, M. M. Kunjapur

"A laboratory scale model furnace was constructed for obtaining radially inward oriented columnar grains in disc shaped castings. The furnace consisted of eleven circular, concentric, equispaced resistance heaters on each half of a split graphite mold. Water or air flowing through a copper pipe along the periphery of the disc constituted the heat sink. After filling the mold, the heaters were turned off consecutively in top and bottom pairs from the rim towards the center, causing the temperature gradients to move inward. Equiaxed structure was obtained at the center by turning off the inner coils together when desired. Sn:15%Pb alloy was used to cast integral blade disc castings using the above technique to obtain dual-property discs with a central equiaxed structure and an outer columnar grain structure projecting inwards from the blades to the rim. A numerical technique was used to predict the temperature profile in the disc during solidification, and good correlation was obtained with the experimentally measured temperature profiles. The corresponding heat transfer coefficient values obtained were h = 544 Wm- 2k-1 (0.013 cal/cm2- ° C-sec) for cooling between metal and chill and h' = 71 Wm- 2k-1 (0.0017 cal/cm2- ° C-sec) for the heat input from the hot mold to the liquid metal. BackgroundHigh temperature alloys used in the current generation of gas turbine engines have evolved through two main stages of development: in 1950's, the increase in the efficiency of gas turbines was paced by improvements in alloy design, which led to the development of Ni and Co-based superalloys (1). By mid-1960's, it was realized that improved alloy chemistry alone was inadequate in meeting the increasingly stringent service requirements. The focus of research then shifted from alloy development to process development, and resulted in the introduction of directional solidification (DS) techniques for the production of turbine blades and vanes (1,2).Under typical operating conditions, the blades and vanes are subjected to aerodynamic loading, while the blades are additionally subjected to high centrifugal loading and vibratory stresses. The primary material requirements for blades may be summarized as follows (1,3):•,High creep resistance•,Good high temperature tensile strength (typically in the range of•,275 to 550 MPa at temperatures in excess of 750°C)•,Resistance to both low cycle and high cycle fatigue (LCF and HCF)•,Resistance to erosion, corrosion, and oxidation•,Resistance to thermal fatigue"

Jan 1, 1986

By A. A. Hejja

The effect of composition on electrical conductivity, viscosity and liquidus temperature of the slags was investigated in the temperature range of 1300" to 1450°C. The synthetic slags containing CaO, MgO, SiO,, A1,0, and FeO were similar to those employed in the electric furnace smelting of sulphide Cu-Ni concentrates containing PGM (Platinum Group Metals) from the Merensky Reef of South Africa. FeO and SiO, were found to affect the viscosity and conductivity the most while liquidus temperature depended on MgO content in addition to these. The activation energy for electrical conduction was found to vary from 67 to 159 kJ/mol and that for viscosity from 125 to 209 kJ/mol. Optimization of the slag composition was attempted on the basis of opposite trend of the viscosity-electrical conductivity relationship with slag composition.

Jan 1, 1994

By A. J. Meir, Paul G. Schmidt

"We present a novel approach to the mathematical analysis and computational simulation of fully three-dimensional, nonlinear, viscous, incompressible MHD flow in complex configurations involving several liquid and solid conductors. Such configurations arise in numerous metallurgical processes. Employing the current density rather than the magnetic field as the primary electromagnetic variable, it is possible to avoid artificial or highly idealized boundary conditions for electric and magnetic fields and to account exactly for the electromagnetic interaction of the flow region with the surrounding space. In addition, the approach lends itself naturally to finite-element based discretization techniques. As an application, we simulate the stationary flow of an electrically conducting fluid around a solid spherical particle of arbitrary conductivity, in the presence of crossed uniform electric and magnetic fields, and compute the Lorentz, pressure, and viscous forces exerted on the particle. This problem arises in connection with the electromagnetic filtration (purification) of molten metals before the casting stage.IntroductionNumerous metallurgical processes are governed by MHD effects resulting from the macroscopic interaction of liquid metals with applied or induced currents, electric and magnetic fields. Frequently these effects are technologically exploited in order to drive or to control the flow of metallic melts. Typical examples include the electromagnetic stirring of molten metals before the casting stage [1]; electromagnetic turbulence control in induction furnaces [2]; electromagnetic damping of buoyancy-driven flow during solidification [3]; and the electromagnetic shaping of ingots in continuous casting [4]."

Jan 1, 1999

By D. H. H. Quon

Results of a study conducted to determine the properties of iron ore pellets made from Mount Wright and Carol Lake ore concentrate fines with partial and full substitution of bentonite by several organic binders are presented. Carboxy methyl celluloses 7H and 6TL, hydroxy ethyl cellulose (natrosol) and modified guar gum all produce pellets of acceptable wet, green and dry strength. However, when fully substituted, an inorganic binder such as calcium carbonate is required for satisfactory strength development after induration. Mixing the Carol Lake ore with Mount Wright ore in a 50-50 ratio also achieves the same result. The failure of the Carol Lake ore in the pelletization process is attributed to the low hematite content of the ore. The results are very similar to those from the extrusion studies reported earlier (8).

Jan 1, 1989

By Arsenio Enriquez, Adrian Deneys

"Rio Tinto through its subsidiary Kennecott Utah Copper Corporation (KUC) and Praxair have implemented the CoJet® gas injection system for copper anode refining. The system provides the capability to melt on average 60 to 70 tons of scrap copper per heat (with acceptable NOx emissions). The system has demonstrated the potential for tuyere-less sulfur and oxygen removal using coherent jet technology.This paper describes the process concept, system development, laboratory testing, implementation, current operation and ongoing developments."

Jan 1, 2009

By J. Borlée, J. P. Birat

"ULCOS is a large European program launched by a consortium of 48 partners led by arcelor and a core group of steel producers, which was started in 2004 with the support of the European Commission (RFCS and 6FP programs) to search for breakthrough process routes that could, in the future, when fully developed, demonstrate the potential of large cuts in CO2 emissions for the production of steel from iron ore.The timescale for commercial implementation is the post-Kyoto period, i.e. 15 to 20 years from today.The present paper presents the progress made in the first 2 years of this 5 year program.Several concepts are being investigated in parallel: re-engineering of the blast furnace to incorporate CCS in the core of the process, smelting reduction with CCS capabilities, massive use of natural with more CO2-lean technologies than today, hydrogen steelmaking and electrolysis of iron ore. Biomass also offers very attractive perspectives, while raising major challenges.None of these new steelmaking routes are ""no regret"", which means that the European Steel Industry has already incorporated extensive energy saving steps in its present process technology and is working as close to thermodynamics limits as is cinematically and economically feasible, and that decreasing GHG emissions further means introducing breakthrough technologies that add significant costs to the operation of the Steel Mills.They will also require much research and development before they can be proven and implemented commercially.IntroductionThe ULCOS program (Ultra Low CO2 Steelmaking) is a large research program of the European Steel Industry and its industrial and research partners launched in September 2004 to investigate steelmaking technologies that have the potential of reducing the CO2 emission of the Industry by a large amount, typically in the order of 50%. It is supported in the European Community by the 6th Framework and the RFCS programs through 3 complementary European projects [1,2].The present paper summarizes the work carried out in the phase 1 of ULCOS and in framing the program of phase 2."

Jan 1, 2008

By Suchun Zhang

The alkaline oxidation of refractory gold concentrates containing arsenopyrite and pyrite at ambient temperatures and pressures has been found to be accompanied by the simultaneous dissolution of gold without the addition of cyanide. A detailed study has been made of the kinetics of the oxidation of the pure minerals and of several concentrates. The reaction products of the oxidation of arsenic and sulphur have been monitored using chromatographic techniques. In the case of arsenopyrite, thiosulfate, monothioarsenate, arsenate and sulfite are the principal products while thiosulfate has been confirmed to be the dominant product of pyrite oxidation. Gold, either as added powder or as a constituent of the concentrates has been found to dissolve simultaneously during the alkaline oxidation of both arsenopyrite and pyrite, and this appears to be associated with the in-situ formation of thiosulfate as a lixiviant. The effects of temperature, stirring speed, oxygen partial pressure, alkalinity and pulp density on the oxidation of arsenopyrite and the dissolution of gold have also been investigated. Keywords: Gold, dissolution, arsenopyrite, pyrite, alkaline, oxidation, thiosulfate, thioarsenate

Jan 1, 2005

By A. M. T. S. Bandara

The solubility of rare earth (RE) salts in aqueous solutions depends on many factors including the type of cations and anions in solution, their concentrations, temperature and the type of solid precipitated. Experiments were conducted using anhydrous La2(SO4)3 and Ce2(SO4)3⋅8H2O as solids and lanthanum(III) perchlorate prepared by dissolving La2O3 in HClO4 solutions as RE-sources. Solutions of H2SO4, H3PO4 and their mixtures in the presence or absence of Na+, Ca2+, Fe(III) or Al(III) as perchlorates served as test solutions. Saturated solutions and precipitated solids were assayed and characterized using standard techniques to show that the La(III) and Ce(III) ions precipitate as hydrated sulphates, phosphates or double salts with sodium, depending upon the solution composition. The change in solubility of RE-salts with solution composition and temperature is the result of the composite effect of changes in solubility products (pKSP) of salts, pKa of acids and other equilibrium constants for ion-association.

By Stein Tore Johansen, Fionn Iversen, Jon Arne Bakken

"A new marker chain front tracking method is used for modelling the meniscus movement during DC casting of aluminium ingots. Modifications have been made to an earlier method developed by Popinet and Zaleski [12] to adapt the model for simulations of meniscus dynamics in the casting process.Initial casting simulations show that wetting conditions in the mould greatly influence the meniscus stability. Controlling the wetting conditions seems to be important for improving the cast ingot surface quality.IntroductionIn conventional direct chill (DC) hot top casting of aluminium extrusion ingot with gas-slip poor surface quality of the cast ingot can be a problem. In the worst cases pronounced surface wrinkling occurs coupled with periodic zones of reduced grain size, macrosegregation and exudation at the surface. The observed surface irregularities are believed to be linked to Periodic surface oscillations or folding of the meniscus resulting in varying solidification conditions.The focus of this work is to gain a better understanding of the dynamics of the meniscus and the influence it has on the finished cast ingot surface through numerical simulations of meniscus movement during the casting process.A two phase marker chain front tracking technique[12] using cubic spline surface reconstruction is applied for modelling the meniscus movement. The advantage of this type of model is its accuracy in the calculation of surface tension forces. Also the wetting can be implemented directly as a boundary condition on the surface spline function. The method is applied in the FLUENT solver, which is based on a finite volume method using the SIMPLE algorithm."

Jan 1, 2001

By J. Hamisch

Climate policy regarding perfluorocarbons (PFCs) may have a significant influence on investment decisions in the production of primary aluminum. This work demonstrates an integrated analysis of the effectiveness and likely economic consequences of different climate policy options. In our study we first compare atmospheric observations to the available estimates of PFC emissions for the baseline years 1990 and 1995. We then present projections for regional emissions of PFCs from the aluminum industry using the MIT Emissions Projection and Policy Analysis model under different policy scenarios. Abatement costs for emissions of PFCs and C02 are compared in the context of the Kyoto Protocol.

Jan 1, 1999

By Makiko Takahashi

A tool is being developed to predict and visualize the microstructural evolution of steels during quenching. This tool utilizes experimental data and reference data that are stored in a database to predict the microstructural development. The visualization tool animates qualitative representation of two- dimensional microstructure drawings as well as the quantitative volume fractions of phases present as a function of time. This is achieved by superimposing the Jominy End-Quench test results over the Continuous Cooling Transformation diagram of the alloy. The predicted microstructure is presented through the web browser to maximize the ease of use. In addition, a parallel coordinate system is used to aid in identifying similarities within the data set by presenting the large number of data at a glance. The results for 4140 steel that was quenched in a wide variety of quenchants will be presented to illustrate the prediction and visualization tools. Keywords: Quenching, Microstructure Prediction, Simulation, Data Visualization, Database, Applet, Animation

Jan 1, 2003

The U.S. Bureau of Mines investigated CaF2-assisted H2SO4 leaching to extract Mn from domestic silicate manganese resources. A pyroxmangite ((Mn,Fe)Sio3) ore containing, in pct, 34 Mn, 23 Si, 3 Ca, and 1 Fe was leached at 90° C for 3 h in a solution containing, in g/L, 12 Mn, 140 H2SO4, 130 (NH4)2SO4, and 5 CaFz. Manganese extraction of 92 pct was achieved. Manganese of greater than 99 pct purity was prepared by electrolyzing the purified pregnant solution at a current density of 50 mA/cm2. The current efficiency was 65 pct.

Jan 1, 1991

By Caryn Wendt, Donna Post Guillen, Armando McDonald, Erik R. Coats, Chaston Ellis, Kevin Feris

Dairy operations constitute ~2.5% of annual U.S. greenhouse gas (GHG) emissions, making dairies one of the largest sources of industrial GHG emissions. We are developing a novel, integrated system to achieve a net reduction in dairy GHGs while producing value-added materials and products. This integrated manure-to-commodities system converts dairy manure to bioenergy, sequesters carbon by converting volatile fatty acid-rich fermenter supernatant to bioplastics, and utilizes anaerobic digester (AD) and polyhydroxyalkanoate (PHA) reactor effluents to produce algae that can be harvested and internally recycled to enhance PHA production and sequester carbon. A decision-making tool is being developed for the integrated system that quantifies net GHG reduction, carbon sequestration, nutrient management and economics.

Jan 1, 2016

By A. Kontopoulos

The extraction of nickel and cobalt from low-grade greek laterites by sulfuric acid leaching has been studied. Batch and continuous mini-plant atmospheric leaching as well as pressure leaching techniques were employed. Atmospheric leaching at temperatures as high as 95 OC generally resulted in low Ni extractions (up to 82%), high acid consumption (650-850 kg/t ore or 80-100 kg/kg Ni) and high Fe co-dissolution (30%). Pressure leaching at 260 OC increased Ni extraction to over 98%, with minimal Fe co-dissolution (2.5%); acid consumption was 300 kg/t ore (31 kg/kg Ni). Detailed experimental results and conceptual flow sheets for atmospheric and pressure leaching are presented.

Jan 1, 1991

By Raymond F. Dalton

Despite the ready availability of numerous zinc sources, the process of solvent extraction- electrowinning (SX-EW) has as yet found little favour in the zinc industry. It is suggested that this is largely due to the previous lack of availability of suitable selective reagents having the particular features required to enable them to fit in to a solvent extraction-electrowinning based process for zinc, particularly with regard to strength and selectivity for zinc over iron. This paper describes work on the development of new selective extractants for the recovery of zinc from both sulfate and chloride aqueous solutions and suggests how they might be integrated into new zinc processes.

Jan 1, 1994

By Farzaneh Sadri

After water leaching of an acid baked REE concentrate, impurities such as Fe, Al, Th, and Cu are removed by neutralization with different reagents such as NaOH, Mg(OH)2, MgCO3, CaO, and CaCO3. Among these chemicals, lime (CaO) and limestone (CaCO3) are the preferred reagents due to their low costs. However, because of calcium sulfate dihydrate (gypsum) precipitation, they are not so common in industry. One of the disadvantages of gypsum precipitation is the adsorption of REE to the precipitates, losing a fraction of REE to gypsum which is hard to recover. In this paper, batch and continuous conditions in the impurity removal process using limestone are investigated and the differences between these two processes are examined. Based on the experiments, REE uptake by gypsum significantly increases in continuous processes, and different gypsum morphologies are observed.

By Adam J. Gesing

Eddy current separators are increasingly used by the auto shredder operators to produce higher grade of nonferrous metal concentrate for recycling. While this increases the unit price of the concentrate, metal losses through inefficient metal recovery quickly offset the price differential. We show how to optimize the eddy current separation system at the shredder to maximize mate- rial throughput, nonferrous metal recovery and grade of the nonferrous metal concentrate.

Jan 1, 1998

By C. E. Abbey

Cobalt, iron and manganese play various roles in copper electrowinning using lead–calcium–tin alloyed anodes. Cobalt catalyzes electrochemical water decomposition resulting in lower anode potential and reduced corrosion rates. Iron reduces cathodic current efficiency, but is used to reduce higher oxidation states of manganese that oxidize organics in solvent extraction. Manganese also produces anode scale and is generally considered a problematic impurity. The effect of the combined interaction of these three metal ions on the anode potential has not been quantified yet. The current work used a three factor, two level, three replicate central composite design of experiments to analyze the effects and potential interactions among cobalt, iron and manganese. The experiments consisted of chronopotentiometric analysis to assess anode potential after 24 h of operation. Higher [Co], lower [Mn] and either high or low [Fe] yielded lower anode potentials. Two regression models were developed to predict anode potential as a function of [Co], [Fe] and [Mn]. A method to estimate electrical energy consumption for copper electrowinning is also presented.

Equilibrium calculational software programs can be effectively utilized to illustrate the importance of activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation to students studying hydrometallurgy. The calculational program STABCAL will be demonstrated. illustrative examples for the creation of diagrams such as EH-pH, activity or concentration-pH and activity or concentration-EH will be presented to demonstrate the fundamentals of real hydrometallurgical systems. Speciation, titration and mixing will be used to simulate or predict operational processes. Applications will include treatment of Acid Mine Drainage (Berkeley Pitlake water and sediments), mass balance potential/pH diagrams, leaching and selective separation of metals from electroplating sludge, metal adsorption at femhydrite surfaces, and flowsheet development for treating mercury sulfide K106 sludge.

Jan 1, 2002

By A. E. Isaacson

Bureau of Mines researchers developed and tested equipment to measure corrosion rates on a commercial-scale mill as an aid in predicting the effect of corrosion on minerals and how this effect relates to downstream processing. Bench-scale experiments were designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5% of the total grinding media wear in the operations studied.

Jan 1, 1987