Search Documents

By John Hanna

The University of Alabama Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of carbonate gangue from sedimentary apatites (francolite) in the pH range of 4-6, without collector conditioning of the pulp. The process, which does not require an apatite depressant, was modified to beneficiate a high MgO siliceous phosphate matrix from South Florida. The modified process includes two flotation stages, one for carbonate removal, as mentioned above, and the other for phosphate recovery from the siliceous gangue. The selective flotation separation of the carbonate and phosphate from siliceous constituents of the matrix at various pH levels and collector dosages are discussed. In the carbonate flotation stage, about 70% of the MgO was rejected in the froth, and the phosphate flotation stage produced concentrates analyzing about 31% P20S' 0.7% MgO and 4% acid insolubles. The overall P20S recovery in the two stages is about 85%.

Jan 1, 1989

By P. D. Lee

The effect of strontium on porosity formation in aluminum-silicon alloys is not well understood and there is no consensus upon the cause of the effects observed. This paper describes a series of experiments where the effect of adding strontium on pore formation was observed directly with combination of a traditional temperature gradient stage and real time micro-focus radiography. These in situ observations provide a new insight into the effect of strontium on the nucleation and growth kinetics of porosity. The addition of strontium was found to have a minor effect on the growth of the pores in the mushy zone. However, strontium appeared to alter the nucleation and stability of hydrogen bubbles within the melt. The interaction of strontium with titanium-boride grain refiners produced an even stronger change in the nucleation and stability of the bubbles formed.

Jan 1, 2002

By E. J. Peuraniemi

Primary copper production using suspension smelting techniques like Outokumpu Flash Smelting always causes some dust formation. Flue dust particles are formed when sulphide feed material reacts violently with oxygen inducing particle disintegration and total desulphurisation of fragments. In the process, flue dust follows the off-gases to the heat recovery boiler (HRB) where its sulphation takes place because of prevailing conditions. Sulphation releases heat and causes also a drop in particle melting temperature and, further, particle sticking to the walls and heat exchange tube banks. Sulphation of synthetic CU20 particles were examined using a laboratory scale fluid-bed reactor. This study aims to a better understanding of flue dust behaviour in a HRB and, thus, to a better operational practise and design of a HRB. The effect of PSO/PO2 -ratio and temperature on the sulphation kinetics were tested. Standard chemical analysis, light optical and scanning electron microscopy with energy dispersive spectroscopy were used to examine the samples.

Jan 1, 2001

By Bingchen Chen, Zhitong Sui, Junwei Ma

"In the blast furnace slag, titanium disseminated in various mineral phases Titanium could be concentrated mainly in perovskite, which could be selectively precipitated and grown by optimizing the operation factors like the slag composition, temperature of heat treatment and additive agents. This study aims at establishing the titanium slag mineralogy and its distribution in the treated slag and the as-received slag, as well as the methods of perovskite separation. After heat treatment, the grain size was grown from 5 - 20µm to 80 - 200µm, the distribution of Ti02 in perovskite was increased from 48% to 81 %, the morphology was changed from snow-shaped grain to coarsening dendrites or equiaxed crystals. A concentrate were produced by gravity separation analyzing 35.25% Ti02 with a recovery of 68.28% and a tailing analyzing 9.53% Ti02 , and a possibility of flotation upgrading was discussed. I INTRODUCTION CHINA is rich in mineral resources of titanium, 92.4% of which is vanadium-titanium bearing magnetite. About 53% titanium were in iron concentrate after mineral processing, by which the blast furnace slag containing about 25% TiO2 were produced[11 • The content of TiO2 in such slag is too low to separate titanium dioxide, and it is also too high to produce slag cement[21. It has been accumulated to 50 million tons so far, which is still increasing at a rate of 3 million tons per year, and results in a waste of titanium resources and pollution of environment. Due to the dispersed distribution of titanium component in various mineral phases, very fine grain(<10µm) and complex interfacial combination, it is very difficult to recovery titanium component from the slag by traditional separating technique. In this paper, a novel technique to recovery titanium from the waste slags was proposed [3H4l, on which three continuous processes were involved: selective concentrating, selective growing and selective separating. Perovskite was designed as a titanium-rich phase, in which the most titanium was concentrated promptly, then perovskite could be selectively grown and coarsened by optimizing the heat treatment and the appropriate additives [ 5l[6l. The grain size of perovskite phase was larger than 80 µm, and the crystals appeared as coarsening dendrites or equiaxial grains like lump."

Jan 1, 2000

By D. M. Hausen

It has been demonstrated that microscopic techniques can be applied in a practical manner to the study of spodumene liberation in the processing of pegmatitic ores at the Kings Mountain spodumene plant, Kings Mountain, North Carolina. Spodumene and associated non-opaque gangue minerals are identified and quantified by microscopic point-counting of polished thin sections of heads, concentrates, middlings and tails fractions. Specially prepared polished thin sections? provide uniform thickness of particles for measurement of diagnostic optical properties and the alternate use of incident and transmitted light in distinguishing the various gangue and ore minerals. Spodumene is commonly associated and interlocked with quartz, albite, microcline and muscovite. Concentrate grade depends on the degree of spodumene liberation, which in turn depends on the crystal size and textural association of interlocked minerals. The liberation of spodumene can be measured as a function of screen size by means of microscopic point-count data. Microscopic data also provide useful metallurgical information about the nature of diluent minerals in spodumene concentrates, and the form of lithia losses in the tails. Lithium assays correlate closely with microscopic spodumene analyses in various flotation products from Foote Mineral&apos;s Kings Mountain plant, and confirm the applicability of quantitative optical microscopy to the study of liberation and recovery of spodumene from pegmatitic ores. A better understanding of recovery-grade relationships was developed as a result of quantitative microscopy studies.

Jan 1, 1981

By Shengli Wu, Mingyin Kou, Laixin Wang, Zhe Wang, Xinliang Liu

The sticking behavior of iron ores in the shaft furnace is one of the most important problems in the COREX melting progress, which directly influence the smooth operation and productivity of shaft furnace. Therefore, it is of great importance to study the sticking behavior of pellets in COREX shaft furnace. The results showed that porous metallic iron produced at the interface of pellets samples was the main reason for the sticking of pellets in the COREX shaft furnace. The SI (sticking index) and metallization rate increased with the reduction temperature and gas flow, and decreased with melting rate. However, the SI of pellets in the COREX shaft furnace could be decreased by the proper match of melting rate and reduction temperature, reduction temperature and gas flow, while the metallization rate of pellets were kept at a certain level. Furthermore, the matching of melting rate and reduction temperature was more effective than the matching of reduction temperature and gas flow.

Jan 1, 2016

By A. Mezei

Samples of cobalt and bismuth concentrates produced from the NICO deposit in Northwest Territories were subjected to a comprehensive metallurgical testwork consisting of: pressure oxidation, ferric chloride leach and carbon in leach, to recover the cobalt, bismuth and gold, respectively. A specific testwork program was designed to allow for the optimization of process parameters under multiple restrictive criteria. The overall objective was to establish leaching sequences that could produce acceptable recoveries while generating environmentally disposable residues as well as solutions suitable for further processing. The recoveries for the leaching stage, under the optimum conditions, were 97% for cobalt and 95% for gold, in the case of the cobalt concentrate. The bismuth concentrate produced recoveries of 99% for bismuth, 99% for cobalt and 97% for gold, respectively

Jan 1, 1999

By S. Seetharaman

The present paper presents. the concept of micro-models and illustrates the application of the same in the simulations metallurgical processes. Development of micromodels requires access to accurate thermodynamic, thermophysicaland kinetic information for the relevant systems with suitable models to extrapolate the data as functions of temperature and composition. Experimental measurements and modelling of the thermodynamic properties, sulphide capacities and viscosities of oxide melts carried out in the department are presented. The incorporation of these models in process models, with special reference to ladle refining of steel is illustrated. Typical example of micro-modelling of solid-gas reactions is also presented.

Jan 1, 1999

By E. Maziar Sauber

In order to prepare a more desirable feedstock for a rare earth elements separation refinery, cerium, a penalty element in the refinery feedstock, should be removed from the mixed rare earth elements oxide or carbonate feedstock. In this study, cerium (III) to cerium (IV) oxidation by calcium hypochlorite and subsequent precipitation was used to remove cerium from a mixed rare earth elements chloride solution. A factorial design of experiments was used to determine the effect of process variables such as temperature, pH, and oxidizer addition on the oxidation of cerium (III) using synthetic solutions. Under certain test conditions, all of the cerium was successfully removed from the chloride solution, and some REE accompanied cerium and reported to the precipitate. This proposed technology can allow for low cost removal of cerium from mixed rare earth elements chlorides.

By S. R. Reddy, R. G. Reddy

"The Margules equation is used for interpreting excess Gibbs energy of several ternary systems. In the present study activity coefficient of a dilute solute, 2, in a binary solvent 1-3 was derived. The derived expression is used to interpret logarithmic activity coefficient of oxygen and sulfur in several metallic systems. Self interaction parameter of the solute is derived from the partial function of solute using constant compositional path. An expression for logarithmic activity coefficient and self - interaction parameter of solute is also derived using Maclaurin infinite series. The derived equation is based on Maclaurin infinite series used successfully to deduce thermodynamics of self interaction of oxygen as a interstitial atom in two metallic systems. The predicted thermodynamic parameters values using Maclaurin infinite series and Margules equations, are in excellent agreement with the experimental data and also our predictions are far more accurate than the predictions made by other models.1 IntroductionIn most of the pyrometallurgical high temperatures processes, interactions of solutes such as oxygen, nitrogen and sulfur, with the solvent atoms are most important during refining processes. There are numerous theories are developed [1-25] to interpret the thermodynamics of solutes in multicomponent alloy systems. Which are mainly developed using statistical or Quasichemical equations.Wagner [4] developed one energy parameter ideal solvent model based on activity coefficient of solutes compositional dependency. He used one energy interaction term which is not able to account for interaction energy parameters for the same solute concentration at different solvent compositions and also it is ineffective model to predict for strong interacting systems."

Jan 1, 1996

By R. G. Reddy

The Margules .equation is used for interpreting excess Gibbs energy of several ternary systems. In the present study activity coefficient of &apos;a dilute solute, 2, in a binary solvent 1-3 was derived. The derived expression is used to interpret logarithmic activity coefficient of oxygen and sulfur in several metallic systems. Self interaction parameter of the solute is derived from the partial function of solute using constant compositional path. An expression for logarithmic activity coefficient and self - interaction parameter of solute is also derived using Maclaurin infinite series. The derived equation is based on Maclaurin infinite series used successfully to deduce thermodynamics of self interaction of oxygen as a interstitial atom in two metallic systems. The predicted thermodynamic parameters values using Maclaurin infinite series and Margules. equations, are in excellent agreement with the experimental data and also our predictions are far more accurate than the predictions made by other models.

Jan 1, 1996

By Milton Blander

A review of concepts and theories for predicting thermodynamic solution properties of multi- component high temperature liquid solutions is reviewed. During the last 50 years the ability to predict :such properties for molten salts, silicates and metals based on the generally known properties of the lower order (often binary) systems has been developed and shown to provide predictions which are quite useful in science and technology. There are many gaps in our understanding of these high temperature solutions, especially for metals, and considerably more work is needed.

Jan 1, 1996

By Fei Ruan, Chang Jie, Jieyu Zhang, Jifang Xu, Kuochih Chou

"Viscosity is an important physical parameter of slag in metallurgical processes. Most studies of aluminosilicate and aluminate systems assume that aluminum occurs in tetrahedral coordination. In this case, the O/Al value was utilized to describe the slag structure in terms of the network character of aluminosilicate and aluminate systems. Composition and viscosity data from the literature and the trends were analyzed according to the O/Al value and temperature. It is shown that the O/Al value explains the trends in more than ten systems, containing more than 200 data points. In aluminosilicate system, the trend that viscosity value changed with the O/Al value which implies that alumina works as network modifier such as basic oxides or works as network former. In aluminate system, irrespective of the system and temperature, viscosity decreased steadily when O/Al value increased.IntroductionMetallurgical slags, which are made of oxides and many also contain fluorides, play an important role in metallurgical processes such as iron making, steel making and secondary refining processes. Aluminosilicate slags are applied in a wide range in metallurgical processes. A polymerizing effect of the addition of aluminum and an association of aluminum with low-field strength cations is further supported by the physical variations in aluminosilicate and aluminate systems. The behavior of alumina in silicate melts has been studied by various authors [1-6]. It is generally accepted that Al2O3 is amphoteric [7] because Al3+ ions can behave in profoundly different ways in a silicate melt. When added to a pure silica melt, Al2O3 acted as a network modifier, breaking the bridging oxygen of the pure silica network, thereby decreasing the viscosity in a similar manner to other network modifiers, such as CaO, MgO etc. to form [1/2Ca (AlO4)]4- complexes. However, when added with alkali or alkali-earth metal oxides, some of the Al3+ ions assumed tetrahedral coordination and replaced Si in the liquid network, the missing charge was compensated by Me+ or Me2+ ions. Therefore Al2O3 acted as network former [8, 9]."

Jan 1, 2011

By Hong Yong Sohn, Miguel Olivas-Martinez

"Different approaches are used for calculating the ‘energy requirement’ of a process. The determination of energy requirement becomes confusing for a process in which a fuel is also a reactant. The key issue is which heat of chemical reaction should be included in the ‘energy requirement’ value. We will use the example of ironmaking processes to illustrate the problem. The different approaches essentially boil down to the question: does one include the combustion heat of the reductant used in the reduction reaction or just the heat of the reduction reaction? Depending on the viewpoint, either approach can be accepted; it is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of a process depends on the choice. The energy requirement of a novel flash ironmaking process will be compared with that of an average blast furnace operation.IntroductionDifferent approaches are used for performing energy balance calculations and perhaps more significantly in presenting the ‘energy requirement’ of a process. The question becomes more involved for a process in which one or more reactants are also used to generate the process heat by combustion. Often the key issue is which heat of chemical reaction to include in presenting the ‘energy requirement’ of the process.It is worthwhile to note at the outset that the difference in energy requirements between different processes for converting similar raw materials to the same desired product is largely unaffected by the choice of chemical reactions to be included. However, the absolute value presented as the ‘energy requirement’ of a process can be different by a large amount depending on the approach. We use the example of ironmaking processes to illustrate the problem. In these processes, as currently practiced or under development, carbon and/or hydrocarbons (including hydrogen) are used as the fuel as well as the reactant for reducing the iron oxide mineral.The different approaches in this case essentially boil down to the following question: does one include the combustion heat of the reductant used in the reduction reaction or treat the reductant portion as just a reactant? Depending on the viewpoint, either approach can be considered acceptable. It is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of an ironmaking process (e.g., the currently dominant blast furnace process) depends on such a choice. It is particularly important to clearly state the specific approach used when the energy requirement of ironmaking is compared with those of other industrial processes such as petrochemicals production."

Jan 1, 2014

By E. Fregeau-Wu

The mineralogy and grain size distribution of phases in a steelmaking slag and experimental products from the heating of the slag under various conditions were determined to explore the possibility of recycling of the iron and manganese to the blast furnace. The steelmaking slags consisted of three major phases: dicalcium silicate, dicalcium ferrite, and Mg-Mn-wustite. Most of the phosphorus was contained in the dicalcium silicate and to lesser extent in the dicalcium ferrite. Due to the fine grain size of the dicalcium silicate, grinding and magnetic separation required pretreatment to increase the grain size and hence the liberation. Experiments on a steelmaking slag were conducted by heating the slag to 1633-1748°K( and slow-cooling in an inert atmosphere at various rates with or without the addition of fluorspar (CaF2) as a flux. Grain size distribution analyses of the starting material and the slow-cooled products were performed using the SEM-IPP area scan method and the QEM*SEM linear scan method. Comparable and reproducible results were obtained on the same sample using both methods. A size versus volume percent plot showed the increased grain growth most effectively. Examples of the grain size distributions obtained were used to show that a higher soaking temperature prior to slow-cooling, a slower cooling rate, and the addition of fluorspar to the slag promoted grain growth.

Jan 1, 1989

By Fan Jiang, Haigang Wang, Shi Liu

"This paper describes several applications of Electrical Capacitance Tomography (ECT) in gassolid two phase flows. A new image reconstruction algorithm was evaluated by both simulation and experiments. It is then applied to the online measurement of solids distributions in square circulating fluidized beds (CFBs) and good results were obtained. From the measurement of solids distributions in the bottom zone of a CFB, a bubbly fluidization pattern is identified. A cross-correlation technique was combined with the solids concentration measurements to obtain the flow rate through the dip leg of the cyclone, i.e. the circulating rate of a test CFB. The same· technique was applied in a dense phase pneumatic transport pipe provides the solids concentration, and the flow rate of a wavy gas-solids flow.IntroductionElectrical capacitance tomography (ECT) has been developed for imaging multiphase distributions in the 90's of the ·last century. It is a non-intrusive method. The principle of ECT can be firefly described as follows:Firstly ECT uses a number of electrodes to surround the measuring zone, depicted by Fig. I. The capacitances between the electrodes are measured in turn and an array C is obtained that contains a total number of m independently measured capacitances. Meanwhile the measuring zone is virtually divided into a grid of n pixels, represented by an array G, named the image vector, the gray level of each pixel represents the local value of the concentration of the material. As the material distribution will be reflected by the capacitances between each pair of electrodes, such distributions can be reconstructed according to the measured capacitance, a process called image reconstruction. A common image reconstruction method is called linear-backprojection (LBP). It linearize the relationship between the dielectric distributions in the measuring zone and the capacitances between the electrodes as the following:"

Jan 1, 2004

By I. Goy D. Gaballah

Decontamination of synthetic K2Cr2O 7 solutions containing 10 to 1000 ppm of hexavalent chromium using chemically treated barks have been studied at a laboratory scale. Metal removal from solutions depends on the pH, the initial concentration and the bark species. The use of a pulp density of 2 % in an agitated flask at the optimum pH for 2 hours leads to a percentage chromium removal of about 95 of the initial metallic ions content. Other trials conducted by column percolation permit the determination of the maximum retention capacity of the treated bark. Depending on the bark species, oak or pine, the rate of saturation is 110 and 215 mg of Cr per gram of bark respectively. The incineration of the metal charged barks gives recyclable, ashes containing 36 and 54 % of chromium metal for the oak and pine barks respectively. Experiments, of Cr6+ removal from industrial effluents containing up to 1800 ppm have been carried out on the semi-pilot plant scale. They have lead to the elimination of about 90 % of hexavalent chromium from this industrial waste solution. Further studies are conducted in order to define the hexavalent chromium binding mechanisms on bark constituents.

Jan 1, 1992

By Isrun Bohlinger

Resources recovery of brasses for semifinished products often results in the formation of hard spots impairing the quality of following abrasive and/or surface finishing processes. A short survey is given on the recycling processes, followed by the actual knowlegde of genesis, composition, and possibilities of avoidance of hard spots. Informations on genesis and composition of hard spots are completed by data from recent experiments.

Jan 1, 1998

By Yu Hu, Gabriella Tranell, Song Zhang, Eivind Johannes Øvrelid

"In the present research, recycling feedstock of silicon for Photovoltic (PV) application is investigated. Whether these recycling feedstocks are reliable in the future use is discussed in this work to assess the properties of the crystal silicon ingot, which is commercially pulled from top-cuts of casted multicrystalline ingot via one kind of Czochralski method - FerroTech. Dopant is the acceptor type Boron (B) and growth direction was <100>. Crystal diameter and the length were 190mm and about 1700mm, which were controlled by the temperature and the pulling speed, then cut to 156mm * 156mm wafers with 2000um and 200um thickness. Resistivity measurements of these wafers by Four Point Probe (FPP) are in good agreement to the calibrated profile after Rapid Thermal Process (RTP). In this work, the Minority Carrier Lifetime MCI, shown by Carrier Density Image (CDI) and Quasi Steady State Photo Conductance (QSSPC), gives the mapping results on the cross section and the relationship to the injection level, increases in an arrange from 40us to 90us along the ingot height, which is abnormal distribution compared to the standard ingot. Then Oxygen and other metal impurities distributions, measured by Flourier Transform Infra - Red (FTIR) respectively, account for the novel phenomenon of the continuously increased MCI. Various types of heat treatments were performed on these wafers (different ingot and different positions) in N 2 and 0 2 mixture atmosphere. Before and after heat treatment, micro-defects were revealed by copper decoration and etching work. Solar cells are fabricated by Energy Research Center of the Netherlands from the experimental ingot, and processed under an industrial standard line. Compared to results of the reference mono-crystalline and multi-crystalline silicon solar cells, the performances of experimental ones show excellent efficiency values up to 18.5%, and Jsc values up to 37mA/cm2.IntroductionThe PV industry has gone through rapid development, with a high growth rate resulting in an increasing demand for silicon feedstock. In addition, costs in production need to be reduced such that solar energy can compete other conventional and renewable energy. Searching low cost, reliable and efficient feedstock is one promoting way to improve and enhance the competitiveness of the PVindustry.More and more researchers start searching new raw materials for PV application [1]-[4]. The key to make full use of low cost raw materials is to control the distribution and effect of impurities, such as Carbon, Nitrogen, and other metal contamination [5]."

Jan 1, 2013

Carbon injection into metallurgical slag is important in electric arc furnace (EAF) steelmaking for foamy slag practices and in nonferrous slag cleaning operations. The current publication presents kinetic data for coal injection into EAF slag to understand the interaction between injected carbon and metallurgical slag. Coal particles were injected into EAF slag and the kinetics were followed by gas and slag analysis. The results were analyzed, in terms of fundamental rate equations for each possible reaction step, as a function of temperature and slag composition.

Jan 1, 2003