Search Documents

By A. B. Cecala

The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour(acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec(50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average mill-wide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al.,1987).

Jan 1, 1995

By Raymond E. Zimmerman

The use of standard dense-media cyclones is well known, as they have been in use for many years. They are especially well suited for operating at low separating densities and for treating difficult coals containing a high percentage of near-gravity at the point of separation. Very few modifications of the basic design have ever been made. The author recently, however, has been interested in the development of a new type of dense-media cyclone that has been produced in Japan. He has observed the testing of this unit and has collected much data which he feels should be of considerable interest to coal preparation engineers. He feels that this unit, called the Swirl Cyclone, may be of substantial value as an alternate to the standard cyclones. It is certainly worthy of further investigation. There has been relatively little written in English-language publications on the Swirl Cyclone. It was briefly described at the Fifth International Coal Preparation Congress. I It has been described in a general manner by the author in two prior publications. 2, 3 This paper proposes to describe this device in more detail and at the same time submit technical data illustrating its wide characteristics.

Jan 1, 1977

By Aleksandar N. Nikoloski, Rorie Gilligan

Brannerite, UTi2O6, is the most common of the refractory uranium minerals and requires leaching under intense conditions to effectively extract the uranium contained within. Brannerite is often found together with apatite in metasomatic uranium deposits. Apatite and other phosphate gangue minerals can inhibit uranium leaching by generating phosphate ions which interfere with the reactions between acidic ferric sulphate and uranium minerals. As part of a detailed fundamental study on the leaching reaction mechanisms for brannerite, tests under a range of selected leach conditions were carried out with the addition of 10 g/L fluorapatite with the goal of identifying conditions where the negative effects of phosphate are reduced. Leaching was carried out for 5 hours with 0.05 mol/L Fe3+ as Fe2(SO4)3 with 0.25–1.00 mol/L H2SO4 and at temperatures between 25 and 96 °C. A single test was performed with 0.05 mol/L Fe3+ as FeCl3 and 1.00 mol/L HCl. In the sulphate system, the effect of phosphate was weakest at the highest acid concentration (1.00 mol/L H2SO4). In the chloride system, phosphate did not suppress uranium extraction, suggesting that HCl leaching could be a viable alternative for the leaching of high-phosphate refractory uranium ores.

Mar 17, 2021

By J. Fisher, M. Barish

Over the past several years, Somerset International has successfully installed over 20 patented Sub325® Fine Coal Recovery Systems in the United States, Australia, Canada and Russia. These installations recover between 5 TPH and 40 TPH for the host sites. In addition to the increased revenue from the direct recovery of a recirculating load (Screen Bowl “Insurance”, Direct Recovery vs. Indirect Recovery via Recycle, CPSA 2020), host sites have seen benefits ranging from improved operation of refuse equipment to a reduction in the solids content of the refuse streams. As Somerset has improved ultra-fine coal recovery through the introduction of Sub325® Effluent Flotation and, most recently, the Sub325® Effluent Settler™, the amount of coal that has been recovered from these systems has increased by up to as much as 25%. Many host sites have taken a sense of ownership in the Somerset system and consider it to be a critical circuit in the overall optimal performance of the plant. In the past year, Somerset has taken the initiative to expand upon the capabilities of the Sub325® Fine Coal Recovery System, primarily the Sub325® Solid Bowl Centrifuge, to include Refuse Tailings Dewatering to allow for co-mingled refuse disposal. As slurry ponds and boreholes are becoming difficult to impossible to permit and operate, there is a need for a reliable, low-maintenance, continuous operation that can produce a handleable refuse cake. Refuse tailings disposal applications are by no means limited to coal plants and impoundments. Somerset has successfully tested at iron ore and phosphate locations throughout the world and have begun commercial installations. The ability to dewater -325 mesh material, whether it be coal, coal refuse, iron ore tailings, or something else, is a vital piece of processing capability for the continued production of mining operations across the globe. This paper highlights the success that Somerset has had in the coal industry worldwide as well as the initial successes with phosphate, iron ore, and copper tailings (patent pending).

Mar 2, 2022

By Gill Montgomery

Although fluorspar is considered an industrial mineral by usage and value, its geological occurrence and the mining and milling methods employed make it more akin to the non-ferrous metal ores. Likewise methods of exploration for it are more like those used in the search for lead and zinc, with which fluorspar is often mixed. In fact, it often takes the mixture of fluorspar, lead, zinc, plus maybe barite to add up to enough recoverable values to make the mineral an ore by definition. This is so true where the fluorspar portion is low grade, perhaps less than 25 percent. Until the development of modern steel milling in World War I times, the invention of aluminum smelting, and development of the fluorine chemical industry and air conditioning, there were few uses for fluorspar aside from ceramic fluxes in the flint glass industry and for uses as glazes for pottery and china. Pure fluorite crystals have long been admired as semi-precious and ornamental minerals of many delicate colors.

Jan 1, 1983

By N. Edmonson

An examination of the statistics of the world phosphate fertilizer industry since 1980 reveals an increasing tendency for fertilizer manufacturing activity to concentrate in phosphate rock mining areas. The economic justification for this resource-oriented strategy is clear. The choice between shipping phosphate rock, a comparatively low-value product, and shipping more valuable finished fertilizers will always be resolved in favor of the latter if cost considerations control the decision. The historical existence of substantial phosphate fertilizer manufacturing capacity oriented toward fertilizer-consuming activities and dependent on imported phosphate rock shows that narrow cost considerations have not always determined the industry's location. One is entitled to ask what conditions have changed to precipitate the observed relocations, and how permanent these changes are. These questions are the subject of this investigation.

Jan 1, 1995

By James L. McGregor

St. Joseph Lead Company has been paying incentive bonuses for well over 40 years. In 1958 almost half of St. Joe's 1,860 employees in Southeast Missouri received some form of incentive bonus in addition to their guaranteed wages. There are very few payroll jobs in St. Joe s Southeast Missouri organization that lend themselves to a reasonably good measurement of production or quality, or both, where an incentive bonus is not paid. The term "Incentive Bonus" is used to differentiate betwen bonuses that are based on quantity or quality of work, and those that are merely additional pay of a standard amount per hour or day because of an employee being temporarily assigned to some unusual task, An employee temporarily assigned to a job where the working conditions make the job performance unusually difficult or where a special skill is used is often given a bonus of some standard amount per hour or shift in addition to his usual rate. This is merely a convenient way of paying something extra without disturbing the normal rate structure. Actually, it is differential pay similar to that almost universally paid for evening and night shift work. Bonuses of that type are not being considered in this paper. The basic reason or theory for paying incentive bonuses 9s to get improved production at lower cost, Unfortunately, it is often difficult, if not impossible, to find a yardstick by which it can be definitely proved that a particular bonus plan is accomplishing its purpose, It becomes, then, a matter of judgment on the part of management personnel as to the value of the bonus plan. The fact that St. Joe Lead Company has continued to pay bonuses for over 40 yews and has increased the number of bonus schedules used attests to a definite belief that they are beneficial to the company's successful operations.

Jan 1, 1960

By Randall D. Peterson

Strip mining with draglines and other surface equipment has traditionally been the method of choice for mining shallow deposits. This is particularly true for soft deposits that require little or no blasting. High rates of productivity and low operating costs have set this standard. However, these methods can be improved. Strip mining methods are batch processes and difficult to accommodate in processing. Moreover, they are encumbered with overburden removal, reclamation expense, and human inefficiencies. This paper describes the invention of a novel shallow earth mining technique called the Softwall Mining Method. Softwall Mining is an adaptation of longwall mining for loose earth conditions. The method was specifically invented for recovering phosphatic clay ore from beds in North Central Florida, but is likely to be suitable for a number of other minerals as well. Potential deposits for which the method may be well suited include placers, disseminated deposits in soft host rocks, bauxite, soft coals and lignite deposits, and other deposits where overburden will subside readily and where the ore can be hydraulically broken and slurried. Unit operating cost advantages are expected over the current dragline systems used. The Softwall mining advantages are its high rates of productivity, control and automation of the mining process, reduction of dilution and waste, and elimination of the majority of stripping and reclamation.

Jan 1, 1998

By R. Addison

This is the story of the Carlton Mill. But first-a little geography. For those who do not know where the Carlton Mill is, or, perhaps, have only a vague idea, its location is indicated in Figure 1. The plant is situated on the road between the two old mining towns of Cripple Creek and Victor, 10 the west of Colorado Springs. From Denver, it's about 110 miles by road. The story of the Carlton Mill began with the discovery of gold at Cripple Creek in 1890. This discovery set off a major boom such that, by the turn of the century, there were 450 separate operating mines in the district. Gold production boomed early and declined rather rapidly as indicated by the graph in Figure 2. Significant factors affecting production are shown on the graph-the raising of the gold price in 1934 from $20.67 to $35.00 per ounce and the government executive order L-208 in 1942 requiring the closure of all gold mines.

Jan 1, 1983

By B. T. Lusk, J. J. Silva Castro

Currently, there are several methodologies to assess ground vibrations from blasting. Of all available methodologies, one that is becoming more important is the waveform superposition or signature hole technique. This technique is based on a signature waveform assigned to each hole to build the complete waveform for the whole production blast, using the convolution between the time initiation sequence and the signature hole waveform. In the basic methodology of the signature hole technique, the waveform hole-to-hole is assumed to be the same. Several studies and field tests have proven that the waveform hole-to-hole, even in ideal rock mass conditions (rock mass with little or no joint system), changes. In addition to distance or confinement, other factors that could change the waveform hole-to-hole include different geologic paths from the source to the monitoring point and a different energy output of each hole, due to hole loading, explosive composition and/or contamination, priming, etc. These factors result in varying waveforms generated for each hole, making the waveform produced by each hole a somewhat random process. There is available in the literature some proposals to include variability in the waveform hole-to-hole, but the parameters involved are complex and difficult to estimate. In this paper, the variability in the signature waveform hole-to-hole in a blast event was recorded through a field test, and a proposal to include signature waveform variability to develop an equation based on the Fourier series is presented. This methodology is the basis for a future signature hole analysis using a Monte Carlo scheme, taking into account the variation of the amplitude and the frequency content of the waveform hole-to-hole in a production blast event.

Jan 1, 2012

By Irina Melekestseva, Beltenev. Victor, Victor Ivanov

"One of the major problems discussed over the last years is a possibility of mining of seafloor massive sulfide deposits. In spite of the pessimistic points of view on their commercial development, they are still of great interest and continue to be studied (Hannington et al., 2011). Recently, Barriga (2012) paid special attention to the underestimated amount of massive sulfide hydrothermal fields and pointed to the importance of the buried fields and subseafloor mineralization.This study examines the geochemistry of seafloor and subseafloor precipitates collected at the Peterburgskoe (19°52´ N) and Irinovskoe (13°20´ N) hydrothermal fields (MAR) during the 34th cruise of the R/V Professor Logatchev in 2011. These fields were discovered by the Polar Marine Geosurvey Expedition in 2010 and 2011, respectively (Shilov et al., 2011; Beltenev et al., 2012). The Peterburgskoe field, associated with basalts, is located 16 km west of the main rift valley at the depth of 2800-3100 m at the junction of a large non-transform discontinuity with the second rift ridge parallel to the rift valley. The Irinovskoe field occurs at depths of 2700-2850 m and has a northwestern satellite sulfide site, both confined to an oceanic core complex (MacLeod et al., 2009), which includes mafic and ultramafic rocks. The details of geological structure of the fields may be found in the relevant papers.Diverse samples were collected from the hydrothermal fields: seafloor massive sulfides, Fe-hydroxide crusts, SiO2-rich sulfide-bearing precipitates, and subseafloor mineralized rocks (Melekestseva et al., 2014a). Massive sulfides may be subdivided on the Fe-rich and Cu-rich types. The marcasite-pyrite, pyrite, hydroxide-marcasite, and chalcopyrite-pyrite (Fe-rich) mineral types are dominant in the Peterburgskoe field at lesser amounts of sphalerite-hydroxide-chalcopyrite and pyrite-covellite-chalcopyrite (Cu-rich) massive sulfides. The mineralized sulfide-talc-carbonate-chlorite, chlorite-sulfide-quartz, and hematite-sulfide-quartz rocks host stringer-disseminated sulfides including chalcopyrite, covellite, and pyrite."

Sep 1, 2014

By E. S. Forbus

A process for producing reductive bleach in-situ in kaolin slurries has been developed. The bleach is formed by mixing an iron sponge powder (-325M) with slurry treated with SO2. The process has been successfully demonstrated in production, and applied to several grades. The color, brightness, and viscosity of the bleached product is equivalent to or better than that of product bleached with commercial sodium hydrosulfite . The tested products can be bleached at a cost, which is 38-54% of those associated with the use of commercial bleach.

Jan 1, 1993

By S. M. Khandrika

Most of the coal presently used by the utility industry is cleaned at preparation plants employing wet processes. While water is the mainstay of coal washing, it is one of the least desirable components in the final product causing a reduction of the heating value as well as handling difficulties. Currently available dewatering techniques are inefficient for dewatering very fine coal (minus 325 mesh). The US coal industry has expressed serious concern about utilizing advanced cleaning processes such as column flotation because an efficient and economical dewatering process is not available.

Jan 1, 1992

By D. J. Turk

Faced with decreasing production from the gold heap leach operation, Robinson implemented a drilling and blasting program on the leach pads in 1993. This program offset some of the negative effects of low ore permeability and short circuiting of leach solution that resulted in lower than optimum recoveries. The drilling and blasting program created new solution flow paths and increased gold recovery. Production and pulp assays at depth intervals, prior to and following drilling and blasting, reveal the degree of short circuiting and benefits of the program.

Jan 1, 1995

By S. Dixon

The use of warm (40-50°C) solution for the selective elution (pre-strip) of copper cyanide from gold and silver cyanides adsorbed on activated carbon was found to elute +90% of the adsorbed copper compared to the use of ambient (20°C) solution eluting 50-70% of the adsorbed copper. The warm solution pre-strip elution did have higher co-elution of gold (1-4%) and silver (10-18%) with the copper. The use of ambient solution pre-strip elution co-eluted less gold (0.2%) and silver (2%).

Mar 2, 2022

By G. Southam

Bacterial populations play an active role in mineral weathering in subsurface and near-surface environments e.g., supergene enrichment of Cu at Morenci, AZ. An in vitro bacterial biofilm model was used to examine the interaction between Sporosarcina ureae and ionic gold (which is toxic) or amino acid-gold complexes in gold mobility. The immobilization of ionic gold was between 80-90% for 1 week but as the available, cellular reactive sites became saturated immobilization decreased to 14% within 2 weeks. In the asparagine-gold system, gold immobilization occurred at a high rate (80-90%) throughout the experiment with limited toxicity towards Sporosarcina ureae.

Jan 1, 1999

By Oscar Cabello, Luis Mendieta, Maribel Guzman

Mineral flotation processes generate large volumes of tailings, which must be disposed of efficiently and safely. In addition to dry stack disposal, the possibility of reusing these tailings as aggregates in shotcrete is an interesting alternative. Tailings samples from a mining operation in southern Peru were characterized by granulometric analysis, X-ray diffraction and Scanning Electron Microscopy. Concrete samples were obtained with different tailings formulations. The samples were subsequently subjected to geomechanical testing. The results showed that replacing 20% to 30% of the tailings with aggregates in shotcrete production achieved compressive strengths exceeding 30 MPa after 28 days of curing, with an energy absorption capacity of 500 joules. Results show that this shotcrete can be used in the support stage of the mining cycle in underground mining.

Feb 22, 2026

By Marc Lonoff

Byproducts are more important to the copper mining companies than to the copper market. Copper ores frequently contain gold, silver, molbydenum and cobalt. With the increase in the prices of these metals copper mining has become more profitable. If byproduct prices remain high, additional firms will be attracted to the copper industry; the increased supply of copper will reduce the long-run copper price. However, this is unlikely to happen because the markets for the copper byproducts, especially molybdenum and cobalt, are small. Increased recovery from copper and other sources will depress the prices of these byproducts before the copper price is significantly affected. Should byproduct prices remain high the copper market will both settle at a lower long-run price and be more unstable in the short run. Since changes in the copper price do not affect the entire earnings of a multi-metal mine, the copper price must fall further before such mines reduce output in the short run. Higher byproduct revenues will make copper supply less responsive to copper price; shifts in copper demand will result in greater copper price fluctuations in the short run than they did before.

Jan 1, 1980

By X. Baolin, R. Guru, M. Peiravi, M. K. Mohanty, Z. Qian, R. Ma, Z. Yude, L. A. Ackah

"Acid mine drainage (AMD) is produced when exposed pyrite (FeS2) reacts with air and water to form an acidic solution that usually contain contaminant levels of heavy metal ions. AMD can potentially contaminate surface water and soil if not treated. The primary objective of this study was to investigate the removal of dissolved aluminum, iron and zinc metal ions from natural AMD using water treatment residue (WTR), a low-cost adsorbent. WTR sorbent generated as waste material in drinking water treatment plants (WTP) was characterized and utilized for the sorption of Al, Fe and Zn in AMD collected from an abandoned coal mine site in southern Illinois that generates approximately 20 gallons per minute of AMD. Sorption experiments were performed using batch technique to obtain rate and equilibrium data. The effects of various parameters on sorption capacities of WTR were observed by varying contact time, pH of the AMD and WTR dosage. The adsorption studies showed rapid uptake in general for the first 80 minutes for Fe and Zn but much earlier for Zn. Further increase in contact time did not show significant change in equilibrium concentration indicating the onset of adsorption equilibrium. After the batch treatment of the AMD water with the WTR, the removal of Al, Fe and Zn were 99.8%, 99.85% and 95.5% respectively. The pH of AMD increased from 2.64 to a near neutral point of 6.74 after treatment. The laboratory results show that the low-cost WTR, which is an abundantly available industrial waste, has proven potential to significantly reduce the high metal ions in acid mine drainage. INTRODUCTION Mining activities provide the basic raw materials needed for infrastructure development and economic growth world-wide. However, it is well recognized that mining activities have been the cause of a variety of environmental pollutions, including AMD. Water seeping out of an old abandoned mine is generally characterized by low-pH with heavy loads of dissolved sulfates (SO4) and metal species such as Fe, Al and Zn among other dissolved elements categorized as toxic metals. The Bureau of Land Management’s Abandoned Mine Lands (AML) program reported the existence of about 46,000 abandoned mines in the United States. Several environmental problems have been reported to be associated with these mined out sites such as heavy metal poisoning, loss of vegetation, air pollution etc. (Boulanger & Gorman, 2004)."

Jan 1, 2017

By John M. Heckard

It all started with the National Environmental Policy Act of 1969, which establishes that Congress is committed to restore and maintain environ- mental quality. It directs all federal agencies to identify and develop methods and procedures so that environmental parameters and values will be given equal consideration in the decision-making process, along with economic and technical parameters. Section 102 of the Act directs, among other things, that all agencies will submit a detailed statement on: (1) the environmental impact of the proposed action, (2) any adverse environmental effects which cannot be avoided should the proposal be implemented, (3) alternatives to the proposed action, (4) the relationship between local short term uses of man's environment and the maintenance and enhancement of long term productivity, (5) any irreversible and irretrievable committments of resources which would be involved in the proposed action should it be implemented. Passage of this act has been followed by other legislation, both federal and state. The Water Quality Act of 1970 puts teeth into the previously existing Federal Water Pollution Control Act by requiring a "certificate of reasonable assurance that the activity licensed will not violate the applicable water quality standards." The Clean Air Act of 1970 requires that the Environ- mental Protection Agency establish national air quality standards, as well as standards for significant new pollution sources.

Jan 1, 1973