Search Documents

By S. Gallagher, A. Mayton, R. Merkel

The prolonged exposure of equipment operators to shock and whole-body vibration (WBV) is linked to cumulative back, neck and abdominal disorders. In low coal mines, space restrictions make it difficult for seat suspensions to isolate operators from shock and WBV. Researchers at NIOSH's Pittsburgh Research Laboratory are responding to these issues by investigating viscoelastic foams. For the full-load case, an ergonomic seat made with viscoelastic foams can isolate the shuttle-car operator from shock at 15 Hz. Researchers used results from additional foam testing using an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

Jan 1, 2000

By David I. Dr. Hoyer

The Hicom mill is a conical mill in which a ball or autogenous load tumbles within a high-intensity acceleration field. An autogenous Hicom mill with a power density of about 1100 kw/m3 and a volume of just 4 litres reduced a 50 m quartzite feed to 90% passing 38 microns at a feed rate of 160kg/h (in closed circuit with a hydrocyclone). Batch tests have identified fracture, chipping and abrasion breakage mechanisms at pebble sizes of 5 to 50 mm. The special behaviour of the load in Hicom mills was exploited to develop a novel technique for estimating steady state autogenous load size distributions.

Jan 1, 1992

By I. S. Parrish, D. W. Kappes, G. G. Austin

Micron-sized gold disseminated in lower Cambrian siltstone has been found at the Sterling mine near Beatty, NV. A shoestring-shaped body has been developed by central and fringe drifts and is being mined via a modified retreat room and pillar system. The siliceous ore crushed to 5.08 cm (2 in ) is stacked to 4.6 m (15 ft) over a layered sand, gravel, and impervious PVC base. Gold is leached using a 0.1% cyanide solution and deposited on activated coconut shell carbon. Stripping of the carbon by hot solutions of 1% NaOH and 20% Ethanol yields overall recovery of about 75% of the fire assay head.

Jan 1, 1983

By Peter J. Conroy

Introduction Most subsidence monitoring to date has been surface monitoring to develop empirical relationships of the magnitude and extent of subsidence effects. Federal regulations are forcing a better understanding of subsidence. Empirical methods of subsidence prediction may not be adequate, since the empirical relationships may not be valid between or even within coal fields. A better understanding of the mechanics of subsidence is required in order to develop and verify analytical models. This paper presents some of the results of surface and underground monitoring in longwall faces of a coal mine. The seam thickness in these mines ranges from 5 feet to 6 feet at depths of 600 to 1100 feet.

Jan 1, 1982

By R. W. Smith, R. K. Mehta, X. P. Zheng, A. M. Raichur, M. Misra

Experimentation was per formed on the flotation of apatite and dolomite separately using anionic collectors in the presence of Mycobacterium phlei. Also, the flotation of mixtures of dolomite and apatite in the presence of anionic collectors and in the absence and presence of the bacterium were studied. It was found that M.phlei functions as a depressant for both minerals. However, it functions as a better depressant for dolomite than for apatite. Experimentation was extended to two different Florida dolomitic phosphate rocks. In this investigation a concentrate grade of less than 1.0% MgO was achieved with a 75% P2O5 recovery.

Jan 1, 1999

By A. E. Isaacson, D. B. Dreisinger, G. A. Kordosky

The U.S. Bureau of Mines is researching the application of solvent extraction technology to highly acidic (pH < 1) copper leach liquors. As increasingly complex copper ores are mined for leaching, use of highly acidic leach solutions maybe necessary to effectively recover the contained metal values. A mixture of two commercially available extractants, based on aldoximes and substituted 8-hydroxyquinoline, which has a high transfer efficiency has been identified. A synthetic leach liquor, containing 5 g/L Cu at pH 0.9 was processed utilizing the mixed extractant and a laboratory SX circuit. The loaded organic was stripped with a synthetic barren electrolyte compatible with electrowinning technology.

Jan 1, 1993

By James J. Guesk, Robert W. Reisinger, Timothy C. Richmond

A high-altitude (2,900 m [9,500 ft]) historic underground copper mine in Wyoming is discharging copper-laden water with a neutral pH into an otherwise pristine creek. The Wyoming Abandoned Mine Land program is reclaiming the site under a CERCLA deferral agreement. The clean-up goal is to reduce copper in the mine discharge so that the creek can eventually support a trout fishery. A pilot-scale passive treatment test utilizing sulfate-reducing bacteria has been conducted at the site beginning in summer 1997. Test results show significant reduction in copper concentrations in near-freezing mine water at flow rates ranging to 19 liters per minute (5 gpm)

Jan 1, 2000

By D. C. Yang, J. Ye

A comprehensive flotation study has been conducted on a Chinese fluorspar ore using the packed flotation column developed at Michigan Technological University (MTU). The results are compared with those for a conventional mechanical flotation method on the same feedstocks. Key factors controlling flotation performance of both methods are evaluated based upon a simple statistic design. The flotation concentrate produced in one stage of the packed column has 4% to 5% higher recovery and much lower silica impurity than the concentrate produced by up to six stages using a conventional mechanical cell. The results also show that the packed-column flotation process is particularly suitable for the recovery of finer fluorspar particles.

Jan 1, 1993

By B. Amadei, A. Squassabia

This paper introduces the Rock Mass Median (RMM) index, a statistical measure of the mechanical quality of a rock mass thus is obtained through a mechanistic interpretation of the Poisson stochastic process. This process is the theoretical foundation of the Exponential Model, a probability distribution successfully used in practice to describe the spacing of discontinuities in rocks. Building on the Exponential Model, a simple method to compute RMM based on a widely accepted mechanical quality index is also presented. Verification is per formed through the analysis of two sets of core samples. Hypothesis testing at the 5% level of significance supports the validity of RMM for these samples.

Jan 1, 1994

By R. S. Conti

The US Bureau of Mines (USBM) has developed an inflatable feed-tube seal (IFTS) for high-expansion foam generators. The IFTS is a lightweight, portable, rectangular inflatable bag that can be used by firefighters to rapidly seal large openings, such as those in underground mines, and to simultaneously provide a feed-tube for a high-expansion foam generator. Thus allows fire fighting foam to freely flow to the fire site and control or extinguish the fire. Studies indicated that a high-expansion foam plug will travel 183 m (600 ft) down an entry with a 4.5% rise in elevation, before leakage of foam from around the inflatable partition.

Jan 1, 1996

By Rodney L. Stone

As part of an overall laboratory and plant test program to determine mixing and other techniques relating to the more economic use of bentonite as an iron ore pellet binder, a settling test was developed for measuring the bentonite content within a pellet or within a batch of pellets. Between pellet batches, each containing a different level of bentonite, the dry fracture load is directly proportional to the bentonite content between pellets of the same batch, however, the fracture load is inversely proportional to the bentonite level; this is explained by a negative correlation between a pellet&apos;s size and its bentonite content and the fact that larger pellets can withstand a higher fracture load than the smaller.

Jan 1, 1968

By C. M. Walck

The Rosebud district is located in the Kamma Mountains, southeast of the townsite of Sulphur, Nevada. Since discovery in 1989, LAC Minerals, in joint venture with Equinox Resources, has delineated a resource containing approximately 570,000 ounces of gold and 5,500,000 ounces of silver. The deposit is of the volcanic-hosted epithermal quartz-sericite type. Mineralization occurs in tabular zones in and along the hanging wall of the South Ridge fault, and in cross-cutting high-angle structures. Multiple stages of discontinuous stockwork gold-and silver-bearing quartz-calcite-clay veins cut variably clay-altered, silicified, and sericitized rhyolitic Miocene volcanic rocks.

Jan 1, 1993

By R. N. Tempel, M. Lengke

Arsenic sulfide (orpiment, realgar, amorphous AsS and As2S3) oxidation rates were measured in mixed flow reactors at pH-2 and at temperatures of 25 ° to 30 °C. The measured oxidation rates for arsenic sulfide solids by dissolved oxygen are in the range of 10-11 to 10-10 mole m-2s-1 after being normalized to final surface area. The order of arsenic sulfide oxidation rates decreases at pH-2 from amorphous AsS > realgar > orpiment > amorphous As2S3. Compared to pyrite, arsenic sulfide oxidation rates are approximately 1.5 to 15 times slower than pyrite oxidation rates at pH-2.

Jan 1, 2003

By R. R. Rollins

Field data combined with theoretical derivations were used to design a surface mining operation using explosive casting. Calculated casting results varied from 44% to 65% depending on bench height. The field tests were performed at an Eastern, contour, coal stripping operation. Results from five experimental casting shots, using a shovel and trucks, are summarized and compared to conventional mining methods. The overburden material removed by casting ranged from 35% to 65%, with an average of 50%. Fragmentation was improved, and it was demonstrated that this procedure is economically attractive, with a resultant cost savings of $0.59/m3 or $5.93/t of clean coal.

Jan 1, 1988

By Gary B. Hemphill

The 345 km long Taiwan High Speed Rail Project will connect the island’s two most populated cities, Taipei and Kaohsiung. Kaohsiung is the world’s third busiest port. The 23 km of alignment on Contract C230 requires the construction of 5,879 m of shallow mined tunnels ranging from 137 m to 1,285 m in length. All nine of these tunnels are mined using NATM methodology. Two of the tunnels, T01 and T08 are in the Toukoshan Formation. This paper will discuss the mining methods, ground support design, and the instrumentation installed to monitor and verify its effectiveness in the two aforementioned tunnels.

Jan 1, 2003

By Mason L. Dicks

For many years The Hanna Mining Company has been investigating the flotation of the non-magnetic iron ores located in the Western Mesabi Range of Minnesota.1 During the 1950&apos;s a number of anionic iron procedures were evaluated and in the late 1950&apos;s and early 1960&apos;s the anionic silica floats and the cationic silica floats were tested with improved results.2 The cationic float became more attractive and effective by the use of the improved ether amines. About 1962 a desliming process by selective flocculation was developed by the U.S. Bureau of Hines at Minneapolis&apos;, Minnesota.3, 4, 5 This is a very efficient method of desliming and was first tried with the anionic silica float and then the more practical cationic silica float. In the mid 1960&apos;s The Hanna Research Laboratory began studies to optimize the selective flocculation process for our ores. This was followed by studies to optimize the cationic silica float after desliming by selective flocculation. This testwork was done on large, 500 to 1000 tonne bulk samples of oxidized taconite which were later successfully piloted at .68t/h (1500 Lbs. /hr.). A program was then begun to test the oxidized portions of numerous taconite drill holes to outline the ore bodies and develop mining plans. This paper will discuss our optimization results of both the selective flocculation and the cationic silica float as applied to our various ores. In addition the pilot plant studies and drill core testwork will be discussed.

Jan 1, 1978

By H. J. Ilgner

Previous applications for using waste rock for backfilling in South African gold mines were reviewed and it was found that in many cases the mechanical equipment selected and the design philosophy applied did not meet the requirements. A more simplified system configuration is proposed, which allows the equipment to be relocated as mining progresses. Innovative high-intensity grinding and dense-phase pumping technology are proposed to provide a low-porosity backfill with a particle top size of 5 mm to 8 mm. According to recent rock mechanics modeling work, this comminuted waste backfill material can provide a good compromise between underground support characteristics and reliable hydraulic transportation behavior.

Jan 1, 2001

By T. E. Wilson

The length of Alaska’s coastline, combined with the presence of a significant number of fjords, encourages consideration of marine disposal of mine tailings. However, since various factors govern the viability of the submarine tailings disposal (STD) option, the decision making process is complex. An expert system, called Submarine Tailings Disposal Expert System (STADES) that will help mining project planners explore the feasibility of STD, was developed. Existing literature, supplemented by engineering recommendations, on the various aspects of marine disposal of tailings was reviewed and formed the knowledge base for the expert system. The shell used to develop the expert system was LEVEL5®.

Jan 1, 2001

By M. R. Leonard

It is estimated that between 5 and 15 pounds of solid waste are generated monthly by each individual. Finding a final resting spot for such waste is an important matter. In the "good ole days," dumps of every description and condition were available. Not so now. Almost all states have adopted and are enforcing strict regulations regarding the disposition of solid waste. Many companies, owing to the nature of their business, have potentially good waste-disposal sites available. Cleveland Quarries Company falls in this group; but in spite of our having state and county permits, opposition by the local community denied us the opportunity to provide a needed local service.

Jan 1, 1974

By Lynn B. Hales, John A. Herbst, Thomas L. Gabardi

A system for a continuous determination of the charge volume of grinding media in ball mills and SAG mills has been developed. The system, comprised of a unique measurement device and a model based Kalman filter algorithm, determines grinding media level within a mill and calculates media and liner wear rates. The signal from an instrumented washer mounted on the exterior of the mill shell is used to provide the measurement that, along with mill power and on-line models for media mechanics, result in estimates of mill parameters that can be used in media addition control strategies. Data are presented for a 12.5 x 15 ft. ball mill.

Jan 1, 1990