Search Documents

By G. Bylapudi, A. Spearing, J. Weber, K. Mondal

U.S. National Institute for Occupational Safety and Health (NIOSH) reports state that about 100 million rock anchors are installed annually in U.S. coal mines (Tadolini et al., 2006), and rock-related safety remains an issue. The majority of these coal mines have conditions that make corrosion probable in the longer term. Despite this, very little research has been performed to analyze corrosion and its effects on rock anchors in coal mines. To further evaluate the effects of corrosive conditions in coal mines on rock anchors, three different experiments were conducted during an initial Illinois Clean Coal Institute (ICCI)-funded project from 2008-2009. The results of these experiments were further studied, with additional tests, in the extended ICCI-funded project during 2011-2012. The experiments were destructive testing, electrochemical testing (potentiodynamic polarization tests) and open circuit potential (OCP) testing, conducted in order to study corrosion in environments similar to those found in Illinois coal mines with a focus on major rock anchor types typically installed underground. Destructive test results showed highest reduction in peak strength at higher pH and temperature. From the destructive test results, epoxy-coated and galvanized anchors were observed to be better when compared to uncoated. Electrochemical testing was performed to find the corrosion potential and corrosion rates of ASTM A615 steel grades 40, 60 and 75 in four different solutions of varying sulfur content at ambient temperature. The effect of temperature and pH levels on corrosion potential and corrosion rates of steel grades were also evaluated with additional electrochemical testing, where an increase in temperature with all other constant conditions caused a significant increase in the corrosion penetration rate. OCP data indicated higher corrosion potential values (-mV) for rock anchors in wet areas, when compared to those from the dry areas. OCP test results of the rock anchors from the laboratory corrosion chambers were similar to those measured in the sampled coal mines.

Jan 1, 2013

By N. Ripepi

"The Langmuir model has been widely used for the coal-methane sorption process via an isothermal test. However, even though the temperature-dependent Langmuir model were recognized theoretically and experimentally, the quantitative relationship between the Langmuir’s constants (a & b) and temperature have not been clarified and confirmed by lab test data. This paper collects 158 methane-coal sorption data under different temperatures, which apply the Langmuir model to consider the relationship between Langmuir’s constants (a & b) and temperature (see APPENDIX I). Even though the Langmuir model cannot be used to show the physical state of methane adsorption on coal, it is widely used because of its simplicity and the reasonable explanation of its parameters (a & b). The results from these published isothermal tests confirm that 1) there is no consistent relationship between Langmuir’s constant-a and temperature; 2) the Langmuir model is a temperature-dependent model, and the temperature-dependent feature is mainly shown by the relationship between Langmuir’s constant-b and temperature; 3) The relationship between Langmuir’s constant-b and temperature can be described by both the exponential and linear relationship with dried coal. This paper provides a database for temperature-dependent Langmuir’s model, which can be used for reservoir simulation of coalbed methane reservoir, coal seam degasification modeling for underground coal mines considering the heating effect induced by geotherm and heat injection (via hot water, hot steam, ultrasonic, etc.). INTRODUCTION The isothermal test for gas sorption on coal is one of the fundamental tests in Coalbed Methane (CBM) recovery fields, such as underground coal mine methane degasification, CBM gas-in-place estimation, and carbon dioxide sequestration in un-minable coal seams. Generally, two methods, volumetric and gravimetric, are employed to obtain isothermal data (Bush, A. & Gensterblum, Y., 2012). Based on these two approaches, a series of commercial and self-assembled instruments are built and several calculation methods are used to obtain isothermal data (Bush, A. & Gensterblum, Y., 2012, Gasparik, K., 2014; Goodman, A. L., et al, 2004; Zhang, L., et al, 2013). In the post-processing stage, many models are provided to analyze isothermal data in order to understand the storage mechanism of gas in coal. Common models include the Langmuir model (and its extended forms), the pore-filling model, multilayer adsorption model (BET), and the Gibbs’ model. Among these models, the Langmuir model is the most widely used for its simplicity and functionality. The Langmuir model is expressed as follows:"

Jan 1, 2016

By P. G. Dempsey, J. R. Heberger, J. P. Pollard

During a mine disaster or emergency, underground air can quickly become contaminated. In these circumstances, all underground mine workers are taught to don breathable air supply units at the first sign of an emergency. However, no contemporary oxygen consumption data is available for the purposes of designing breathing air supply equipment specifically for mine escape. Further, it would be useful to quantify the oxygen requirements of breathing air supply users for various escape scenarios. To address this need, 14 participants crawled a distance of 305 m each while their breath-by-breath oxygen consumption measurements were taken. Using these data, linear regression models were developed to determine peak and average oxygen consumption rates as well as total oxygen consumption. These models can be used by manufacturers of breathing air supply equipment to aid in the design of devices that would be capable of producing sufficient on-demand oxygen to allow miners to perform self-escape.

Jan 1, 2015

By R. M. Rowe, T. E. Irwin

A flowsheet was developed for upgrading Climax tin concentrate to about 45 percent Sn. Bench-scale test work conducted at AMAX Extractive Research and Development, Inc., was used to design a multiple-stage tin- processing flowsheet which included screening, high-intensity magnetic separation, and high- tension (electric- static) separation. Formal engineering and plant installation was accomplished in-house by Climax mill personnel. The successful start-up operation of the facility was the joint effort of the AMAX R&D and Climax-mill staffs.

Jan 1, 1986

By J. P. McDonald

Exposure to particulates containing metals and metal fumes (PCMMF) is a potential concern in ore refining and smelting. Some metals of primary interest are arsenic, cadmium, copper and lead, which have been linked to various adverse health effects. The current National Institute for Occupational Safety and Health (NIOSH) sampling method for metals in particulates requires the use of a filter, precision airflow pump and laboratory analysis. A major concern with this method is the one-to-two weeks? wait before laboratory results are available for use in determining if additional controls are needed to assure adequate exposure protection for workers. Particulates containing these metals were sampled during sixteen sampling events at a copper smelter using the traditional NIOSH methods. Monitoring of particulates was simultaneously conducted using a TSI 8520 Dust-Trak real-time aerosol monitor with a 10-µm-cutpoint sampling inlet. NIOSH analytical methods related to particulates and metals (methods 0500, 0600 and 7300) were used to determine particulate mass and individual mass contributions of metals on sample filters. Linear regressions with y-intercepts forced to zero were developed to determine the relationship between the PM10 measurements recorded by the DustTrak and laboratory-reported total particulate mass, PM10 and respirable arsenic, cadmium, copper and lead concentrations. These linear regressions yielded correction factors that can be applied to DustTrak readings to obtain total particulate mass, PM10 and respirable concentration estimates for each of the four metals. The R2 (coefficient of determination) values from the linear regressions ranged from 0.65 for total lead to 0.91 for total copper. These results suggest that the DustTrak may produce real-time data useful in providing estimates for airborne concentrations of arsenic, cadmium, copper and lead in copper smelter particulates.

Jan 1, 2011

By Andrew Cushing, Joe Carvalho, Jon Hurt

"INTRODUCTIONThe shales of the Greater Toronto Area (GTA) have been known to experience time-dependent deformations (TDD); those initiated by excavation-induced stress relief which progress with time as a function of rock porewater salinity, access to freshwater (or air) of lower salinity, clay and calcite content, and the buildup of swelling pressures within the rock mass. These deformations can induce long-term pressures on shaft walls and tunnel linings, especially if the permanent works are constructed soon after excavation, with very little time delay. This paper presents measurements of time dependent deformation of recent shaft and tunnel projects constructed in the GTA, and draws conclusions regarding the main influences on the TDD. The key input parameters for the numerical predictive model are critically assessed. Projects which are discussed include the Billy Bishop Airport Pedestrian Tunnel, Hydro One Midtown Tunnel and Hanlan Feedermain (Contract 3).MECHANISM OF TIME DEPENDENT DEFORMATIONExplanation of MechanismThe Georgian Bay Shale unit consists of typically moderately weathered to fresh, grey to dark grey, fine to very fine grained fissile shale interbedded with slightly weathered to fresh grey, fine grained calcareous siltstone and limestone interbeds. There are two distinctive features of the shale in the Greater Toronto Area (GTA). One is a high horizontal stress regime, and the second is long-term time dependent swelling behavior which develops when the following factors occur (Lo and Micic, 2010):• Stress relief of the rock mass• Outward salt concentration gradient from pore fluid of the rock to the ambient fluid• Availability of fresh waterThe swelling is a consequence of the reduction in confined stress in the rock which occurs upon excavation in combination with a differential gradient in salinity between the saline rock porewater and freshwater or even humid air. Osmotic and diffusive processes result in a decrease in the salinity of the rock porewater achieved by an overall increase in the water content, resulting in volumetric expansion of the shale rock over time. The development of this time dependent deformation (TDD) relative to the time"

Jan 1, 2016

By S. A. Richards

Business planning in the coal' industry revolves around the production and quality forecast. It is difficult to accurately estimate costs and revenues until the production forecast is made. At mines where production comes from multiple sections, quality is tied to each section's production. Blending becomes a part of the planning process. In order to respond to rapidly changing business climate, a reliable program is needed to accurately forecast the effects of changes in key parameters affecting the production. This paper discusses an efficient, intuitive, and economical approach to underground coal mine planning program which uses a PC-based relational database as the programming platform to forecast production and quality. The program was developed at a major coal company. The relational nature of the production planning data, the programming algorithm, and the underlying principles are discussed in this paper.

Jan 1, 1994

By J. P. Allen

Cobalt, nickel, and manganese can be recovered quickly, cleanly, and selectively from cobalt-rich manganese crust by leaching in dilute acid solutions in the presence of hydrogen peroxide. Common selective precipitation methods can then be used to recover these metals from the leach liquor. The leaching reaction produces only oxygen as a byproduct, and the waste residue from leaching was tested and found to be non-hazardous under existing EPA specifications. The leaching process is effective in either fresh water or seawater. This research is a part of the Bureau of Mines program to identify the mineral resources of the Exclusive Economic Zone and devise methods for recovering their valuable components.

Jan 1, 1990

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

"The National Institute for Occupational Safety and Health (NIOSH) has recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with medium-sized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in this study: a 15.2-cm (6-in.) wide shelf; a 7.6-cm (3-in.) wide shelf; and a 7.6-cm (3-in.) wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1, and 1:1 were evaluated for the 15.2-cm (6-in.) wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust-collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. The simulation results could be used for future development of dust control methods, particularly to address respirable silica dust, for a surface mine blasthole drill shroud.INTRODUCTION Surface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1% of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples) • 5.8% of rotary drillers were overexposed to respirable silica dust (9 out of 155 samples) • 7.3% of drill helpers were overexposed to respirable silica dust (3 out of 41 samples) • 7.5% of blaster/shotfirer were overexposed to respirable silica dust (3 out of 40 samples) Of significant interest is an x-ray surveillance study recently completed under the NIOSH Enhanced Coal Workers’ Health Surveillance Program (ECWHSP). This program offered free chest radiographs to surface coal miners in 16 states. Pneumoconiosis was found among 2.0% of the 2,328 screened miners with at least 1 year of mining tenure. Twelve miners had radiographic changes consistent with progressive massive fibrosis, and 9 of these 12 miners reported no underground mining tenure. All but 1 of the 9 miners worked at occupations that were in the vicinity of blasthole drilling, either as a driller, blaster, or blast crew member [1]."

Jan 1, 2018

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

The National Institute for Occupational Safety and Health (NIOSH) has recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with medium-sized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in this study: a 15.2-cm (6-in.) wide shelf; a 7.6-cm (3-in.) wide shelf; and a 7.6-cm (3-in.) wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1, and 1:1 were evaluated for the 15.2-cm (6-in.) wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust-collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. The simulation results could be used for future development of dust control methods, particularly to address respirable silica dust, for a surface mine blasthole drill shroud. INTRODUCTION Surface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1% of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples) • 5.8% of rotary drillers were overexposed to respirable silica dust (9 out of 155 samples) • 7.3% of drill helpers were overexposed to respirable silica dust (3 out of 41 samples) • 7.5% of blaster/shotfirer were overexposed to respirable silica dust (3 out of 40 samples) Of significant interest is an x-ray surveillance study recently completed under the NIOSH Enhanced Coal Workers’ Health Surveillance Program (ECWHSP). This program offered free chest radiographs to surface coal miners in 16 states. Pneumoconiosis was found among 2.0% of the 2,328 screened miners with at least 1 year of mining tenure. Twelve miners had radiographic changes consistent with progressive massive fibrosis, and 9 of these 12 miners reported no underground mining tenure. All but 1 of the 9 miners worked at occupations that were in the vicinity of blasthole drilling, either as a driller, blaster, or blast crew member [1].

Jan 1, 2019

By R. R. Klimpel

The efficiencies of plant scale comminution processes are often evaluated by various indices that are calculated and/or measured somewhat independent of the performance of any associated downstream froth flotation processes. In order to compare some specific comminution factors such as energy utilization, media consumption, equipment utilization time, etc. comparisons of comminution efficiency independent of flotation behavior are appropriate. However, as more and more detailed plant level information is gathered on the joint and highly interactive nature of comminution and froth flotation, it is becoming increasingly obvious that knowing and using simple efficiency indices are not enough. What is needed are more performance related measures of the efficiencies of the combined size reduction -froth flotation system for effective plant level economic optimization to occur. The purpose of this paper is to present some examples of important interactions that influence the joint efficiencies of size reduction and froth flotation processes.

Jan 1, 1998

By Nick Chlumecky

INTRODUCTION Column-type supports are used to prevent roof falls in underground excavations. The first individual column supports were made from timber that was cut to fit the irregular heights of mine seams. Because the seam height of the material removed varied throughout the mine, timber posts generally could be used only once. During the I 920s, steel friction props began to appear in British and European mines, and, by the 1950s, thousands of these props were being used. However, the steel friction props were heavy, difficult to install, and difficult to recover. Furthermore, the friction props could not be preloaded, and their yielding behavior was rather erratic. In 1946, hydraulic props were introduced in En¬gland, and, within a few years, they replaced friction props throughout Europe. The first application of hy¬draulic props in the United States occurred in the 1950s, during early experiments with longwall mining. Modern technology and high-production mining procedures have combined to make the use of hydraulic props a very acceptable method of providing temporary heavy-duty support for production areas. In areas such as development headings, where only modest roof loads are expected, lighter-duty jackscrews, ratchet jacks, and light hydraulic props are used. ADVANTAGES OF HYDRAULIC SUPPORTS The acceptance of hydraulic supports has been wide¬spread during the past 25 years, proving their reliability and effectiveness in preventing roof falls. Some of the advantages provided by hydraulic supports are: 1) Individual hydraulic props can be installed within 30 sec, resulting in a minimum exposure of per¬sonnel and equipment to an unsupported roof. 2) Hydraulic props can be preloaded to more than 4.5 t (5.0 st), increasing the frictional resistance between the rock strata. Thus, the roof is kept tight, improving the behavior of the unsupported ground. 3) If gradual roof sagging or bottom heaving im¬poses an irresistible force, the hydraulic prop yields gradually and continues to support the ground. 4) The support capacities of the hydraulic props most widely used range between 10 and 20 t (11 and 22 st). Their support capacities are maintained during yielding to an irresistible force. 5) Hydraulic props can be recovered rapidly. Where no other supports are provided for the roof, as in pillar¬ing operations, the hydraulic props can be recovered by remote means. 6) The length of hydraulic props is readily adjust¬able allowing them to be reused in seams where roof height varies. 7) Studies of mining operations indicate that the use of hydraulic props increases both personnel safety and mine productivity. DESCRIPTION Figs. I and 2 illustrate typical hydraulic props used in mines in the United States. Fig. I illustrates a prop

Jan 1, 1982

By W. C. Hirt

Deposits of ferromanganese crust containing cobalt and nickel occur on the seafloor in the Pacific Ocean near the Hawaiian Islands and Johnston Atoll. This paper describes developmental flotation metallurgy to separate crust from its associated substrate gangue. Important variables in ferromanganese crust flotation include reagent type, aeration rate, conditioning time and agitation intensity, pH, temperature, water type, and feed size distribution. Flotation in seawater of minus 600 ~m (-28 mesh) material assaying 6.2% Mn, 0.2% Co, and 0.13% Ni with diesel fuel-crude tall oil-sulfonate collectors produces concentrates assaying 15% Mn, 0.6% Co, and 0.3% Ni with recoveries of 89-95% while removing 62% of the feed weight.

Jan 1, 1990

By S. Bahrampour

One of the basic requirements for designing an optimized rock support for an underground opening is having reasonably enough geological information. It is often financially impractical to obtain detailed geological information about the rock surrounding the excavations. The geological and geotechnical information which are obtained during the construction phase are also usually inadequate and need periodic operation stoppage. Penn State University- J.H. Fletcher & Co. joint venture is to improve the existing instrumented roofbolter so that the 3D geological and geotechnical map of the rock mass surrounding the underground working can be generated real-time as the data is being collected. This information will also be used to design appropriate support for different sections of mines. In this paper, recent results in improving the performance of the measurement while drilling system will be discussed. Moreover, updates related to borehole probing methods for estimating the properties of the rock masses will be presented.

Feb 23, 2014

By D. Duvris

The main objective of this work was to quantitatively investigate exhaust emission levels, as related to maintenance (service) intervals, during the operation of diesel-powered equipment at an underground bauxite mine in Greece. Such emissions depend on a great number of parameters, including the type (technology) and tuning of the engine, the type of work performed as related to the engine workload, suggested maintenance intervals, the altitude, the temperature and the humidity of the atmosphere of the underground mine, the properties of the fuel, the operator's training and experience level. Necessary ventilation quantities were calculated based on exhaust gas concentration measurements, site specific relationships between pollutants and adjusted air quality indices. Diagrams comparing necessary and recommended air flow for several equipment groups featuring two engine types and for different maintenance intervals are presented.

Jan 1, 1998

By C. S. Simons

The aphorism that provided the title of this paper is probably a couple of hundred years old, but it still expresses a fundamental truth in the metals industry. This truth will be illustrated through a brief review of the major developments in the extractive metallurgy of the oxidized ores of nickel - the "laterite" ores. While the details to be discussed are for the most part specific to nickel, a close parallel with other commodities - particularly in recent years - will be apparent even to those whose interest in nickel itself is slight. Thus it is hoped that this paper will be stimulating, at the least, to anyone who is concerned with the implementation of process improvement, "Invention" in the present context means any change from "conventional" process technology that shows a reasonable chance of reducing costs, increasing revenues, or both, in the production of a commodity. This can be anything from a simple rearrangement of flowsheet steps to a completely different basis for processing. And the result may reduce costs by more efficient use of energy or labor or reagents; may increase revenues by better recovery of the primary product or by introducing the recovery of previously ignored by-products; may insure sales volume (and thereby cash flow) through higher product purity or an improved product form. "Necessity" is the perceived need to attain at least one of these classes of results. This perception of necessity, however, varies widely from management to management and from project to project.

Jan 1, 1983

In this paper, a number of novel hypotheses that provide a fresh perspective on the characterization of strata movements associated with longwall mining are developed by analyzing subsidence measurements with an influence- function-based computer program. With this influence-function technique, easily obtained surface displacements can be used to determine some of the complicated, expensive, and difficult to measure movements of the immediate roof strata in a longwall panel. The primary hypothesis developed by this analysis proposes the existence of an area of partial roof caving near the edge of a panel called the "edge effect." A second hypothesis, interrelated with the first, promotes the importance of the effect of gate-entry closure on the observed strata movements. Both the primary edge effect hypothesis and the secondary hypothesis concerning gate-entry closure are justified and quantified in an extensive analysis of surface subsidence that uses supporting information from related theories, design criteria and insitu measurements. Next, the edge effect and the gate closure hypotheses are extended further and used to provide an explanation of the complex subsidence interaction of adjacent longwall panels in what is termed a "redisturbed" effect. Finally, in the conclusions of this paper, the importance of accurately understanding these longwall strata movements for proper subsidence prediction or gate design is stressed.

Jan 1, 1986

By G. B. Amicucci

A Denver Autometrics Particle Size Monitor, PSM-400, was installed at Golden Sunlight Mines, Inc. in October 1988. The PSM-400 measures the grind product's particle size and percent solids. The particle size is used to control grind size by automatically adjusting mill feed rate. The PSM's continuous response to ore changes has improved grind product uniformity and mill throughput. Metallurgical testing has shown the PSM's accuracy to be +/-1 % + 150 µm (100 mesh).

Jan 1, 1991

By JIAQI JIN, Joe Milbourne, Maoming Fan

Gold is very important to support the financial system, and to be used in industries of the jewelry, high-tech fields such as electronics and aerospace, etc. Gold is mainly extracted from three types of ores: primary ore (vein gold), placer (alluvial gold) and associated ore. Cyanide was widely used in gold ore flotation to depress gangue minerals and leaching/cyanidation. The process of extracting gold from gold ore, its separation and flotation concentrate, specifically through a technique called cyanidation or cyanide leaching. This method, which has been dominant since the 1970s, utilizes a dilute solution of cyanide to dissolve gold from the ore. While effective, the use of cyanide raises environmental and safety concerns due to its high toxicity. Cyanide spills can have severe environmental consequences. This has led to the exploration of alternative, environmentally friendly reagents. This paper discusses processing results using the alternative flotation depressants such as sodium sulfite (Na2SO3), etc. to produce a goldrich flotation concentrate for sale to a smelter or as feed to an alternative leaching agent. and methods to extract gold from ore without relying on cyanide.

Feb 22, 2026

By M. E. Volin

Reagent control for optimum concentrate yield was studied by laboratory batch flotation tests simulating the Groveland plant flotation circuit in which a rougher concentrate is cleaned twice. The reagents were a fatty acid collector, a sulphonate collector and sulphuric acid. The study included two types of flotation feed representative of the reground and deslimed tailing from the spiral concentration circuit, one when the ore mineral is predominantly specularite and the other when it is magnetite. The factorial design included three levels of fatty acid, five levels of sulphonate and five levels of H2S04, with the two types of ore in nested blocks, making up a total of 75 tests. Similarity of results and reproducibility were established in preliminary tests. The final tests were performed in random order under closely controlled conditions following the established procedure.

Jan 1, 1965