Search Documents

By N. Agron-Olshina

The application of the QEM*SEM image acquisition and analysis system to the measurement of the mineral matter in coal and the materials in fly ash is described. A new sample mounting technique was developed using iodinated epoxy to provide a backscattered electron contrast between the coal, the mounting medium and the mineral matter. Several comprehensive and detailed species identification programs for silicate minerals and materials were developed to analyse the 1000 count x-ray spectra used for the measurements. Case studies are presented to demonstrate the capabilities of the new technique to distinguish different coals and fly ashes by their mineral and material composition rather than by conventional chemical analysis. Applications of the new technique are aimed at demonstrating that composition and size distributions obtained from OEM*SEM measurements can be used: 1. to characterize coal with respect to combustion problems in power stations, 2. to characterize coal for fine coal cleaning, 3. to characterize fly ashes in relation to problems such as erosion in combustion systems and the ease of precipitability in dust collection facilities, 4. to refine the classification systems used in marketing coal for pulverized fuel firing and fly ashes as a component of cement and building materials.

Jan 1, 1992

By K. L. Lamb

At the Sierrita mine, 40 km (25 miles) south of Tucson, Arizona, Duval Corporation is rapidly gaining operating experience with its new Portable Crushing and Conveying System, (PCCS). As of November 23, 1983, over 4.5 million tons (5.0 million st) of ore have passed through the system. Mining cost per ton for the months of July, August and September was 83% below the average for the first five months of 1983. Although all the cost reductions experienced cannot be attributed to the Portable Crusher, it was a major contributing factor. The Sierrita ore deposit has several natural topographic and geologic conditions which are not favorable to mining. It is not a sidehill deposit and therefore no low-level exit points exist to facilitate truck haulage. The ore is very hard. Quartz diorite, hardest of the three major rock types, averages 172-207 MPa (25-30 000 psi) unconfined compressive strength and may run as high as 345 MPa (50 000 psi). Blasting in this rock produces oversize material which runs approximately 20% 51 centimeters (20 inches). The ore is low grade, averaging slightly better than .30% contained copper and .035% contained molybdenum, with small amounts of silver. These conditions, plus high design production tonnages, make the Portable Crushing and Conveying System (PCCS) practical for Sierrita. Without crushing and conveying, truck haulage would be prohibitively expensive. A typical, October, 1983, ore haul from the bottom of the pit would involve a vertical lift of 260 meters (850 ft) and a horizontal distance of 3 860 meters (12 200 ft) were not in-pit crushing and conveying available. The corresponding cycle time would be nearly 32 minutes.

Jan 1, 1984

By R. Mishra

The validity of the concept of mine resistance in ventilation systems is examined. Mine resistance is the proportionality constant relating the head generated by a fan and the quantity flowing through it when the fan is connected to a mine circuit. It is the total effect of all branches in the mine ventilation circuit. Its importance lies in the fact that for new mine projections, and in the extensions of existing mines, ventilation calculations are usually based upon adjustments of the mine resistance. In ventilation circuits with regulation, and/or with multi-fans, simple adjustments of the mine resistance curve do not lead to correct solutions. A ventilation system consists of several interconnected subsystems where one subsystem behavior affects that of the others, and the total system. Through a series of simple but realistic examples, the authors will demonstrate the importance of the systems concept in mine ventilation, and its practical application to coal mine ventilation planning.

Jan 1, 1977

By W. W. McClintock

A column flotation system was designed to conduct release analyses of a very finely disseminated, stratiform, copper ore from the Denali Copper Prospect, Alaska. Chalcopyrite is finely disseminated in a carbonate matrix and pyrite is disseminated in both the chalcopyrite and gangue, requiring grinding to 20 microns for adequate liberation. A 25 mm x 2.4 m glass flotation column was designed. The ore and its flotation tailings were repeatedly floated to obtain a rougher concentrate, which was repeatedly floated to produce release fractions. These were analyzed for copper, iron calcium and magnesium. Release curves were plotted. The procedure was replicated at each of two grinds; 99% and 88% passing 37 microns (400 mesh), and should find application for flotation characterization and process selection. Bond grindability work was also conducted.

Jan 1, 1994

By Steve Kral

One of the world’s most successful mining shovel manufacturers believes its name is not very well known in North America, particularly in the United States. And there are plans under way to improve on that. Never mind that it is one of the largest mining shovel manufacturers in the world. Or that the mining division has 800 machines in operation worldwide, 100 of them in the United States. And the company currently holds 30% of market share worldwide and 10% in the United States. Forget about the fact that it has already sold more machines world-wide this year than it did during 1995. None of that is good enough. O&K Mining GmbH Dortmund is the mining division of Germany’s giant O&K Orenstein and Koppel. It is one of three divisions of O&K Orenstein and Koppel AG, a US$1.2-billion company. The other two divisions are construction equipment and escalators. The mining division, though, is one of the company’s most successful.

Jan 1, 1996

By William R. Hess

Volcanic ash, although a little-used Kansas resource, is available in forty counties with estimated, reserves of more than 20 million tons. It was first produced in Kansas in the early 1900?s but not until the early 1920 is did it become an important abrasive material. Total production to date is estimated at 2 million tons, the major use being as an abrasive in scouring compounds and soaps, additional uses include ceramic glazes, an additive in cement, and a filler and stabilizer in hot mix asphalt for paving. Unrecorded tonnages have also been used in construction of black-top (macadam) roads. From 1916 through 1944, Kansas ranked first among the states in volcanic ash production; peak production was about 52, 000 tons in 1923. Since 1945, production has steadily declined, primarily because materials other than volcanic ash are now being used for abrasives; only two producers operated in 1964.

Jan 1, 1965

By Robert L. Frantz

The U.S. Bureau of Mines (USBM) established on August 15, 1983, a Generic Mineral f Technology Center (GTC) for Respirable Dust within the Mining and Mineral Resources Research Institutes (MRIs) at The Pennsylvania State University (PSU) and West Virginia University (WW) in association with participating MRIs at Massachusetts Institute of Technology (MIT) and the University of Minnesota (UMN). The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through researching and advancing the fundamental under- standing of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs. Other Center activities include the training of engineers and scientists, graduate students and undergraduate students through their respective institutions, and the technology transfer to the industry. The Center also serves as the reference center for publications in the respirable dust area.

Jan 1, 1986

By P. J. Ryan

Phelps Dodge’s Candelaria copper-gold mine is located 20 km (12miles) south of Copiapó in northern Chile’s Atacama province (Region III) (Fig. 1). The Candelaria Mine is about 800 km (500miles) north of Santiago and 75 km (47 miles) east of the Pacific Ocean. Its elevation is 600 m (1,970 ft) above sea level. The Copiapó River Valley is 6 km (4 miles) northeast of the mine site. It is the only major source of water in this arid region. The average rainfall is 14mm/a (0.5 in./year). During 1995, the mine produced 521.4 kt (574,800 st) of copper concentrate containing 150 kt (165,000 st) of salable copper and 3 t (98,800 oz) of gold. The 1995 unit cash cost was less than 50 cents/lb of copper. This makes Candelaria one the world’s lowest cost copper producers.

Jan 1, 1996

By Clark Harrison

It is not uncommon for overall quality of coal from a mine to deteriorate as the mine is developed or for an improved-quality coal specification to be imposed during the life of the mine. Either of these conditions typically results in management pressuring mine personnel to take greater care in delineating the seam from top and bottom rock. When mining and seam conditions require a portion of the seam to be removed to ensure sufficient rock is removed to meet the quality specification, physical-coal cleaning may become economically competitive with in-pit seam grooming. The additional cost of coal cleaning may, in some cases, be justified by permitting higher recovery of the coal seam than is possible when cleaning the seam with excavators in the pit. This paper compares projected coal cleaning results with present in-pit grooming techniques and reports the economic results.

Jan 1, 1987

By W. G. Pariseau

Reliable stress measurement using hollow inclusion gauges and monitoring stress change using borehole stress meters and borehole deformation gauges in anisotropic rock remains a challenge for the rock mechanics community. In this regard, the complex variable method advanced in 1983 for deducing stress in anisotropic rock is flawed and software is privileged. Fortunately, advances in computer hardware and software now enable fast, reliable reduction of hollow inclusion stress measurement data for determining stress in anisotropic rock. Monitoring stress change in anisotropic rock poses a different challenge but is also subject to numerical analysis. Stress measurement using a hollow inclusion (HI) gauge such as the triaxial Australian HI is done in four steps: 1) drilling a measurement hole, 2) installation of an HI, 3) stress relief of the HI by overcoring, and 4) data reduction. The last step, data reduction, is the focus of this work. The process is well-known in linearly elastic, isotropic rock (Worotniki and Walton 1976, Duncan Fama and Pender 1980). However, in case of linearly elastic, anisotropic rock the requisite technology is not readily available. This situation is somewhat surprising because anisotropy is more often the rule rather than the exception, especially in the neighborhood of ore bodies. Rahn (1984) has pointed out the potential for significant errors with neglect of anisotropy and the adverse consequences for engineering design. Amadei (1984) has also pointed out the potential for errors with neglect of anisotropic rock properties in stress measurement. Worotniki (1993) cites other studies that indicate potential for serious errors when doing measurements in anisotropic rock. In both theoretical cases (isotropy and anisotropy), data reduction is essentially a composite of solutions to boundary value problems in linear elasticity. In the finite element approach, the analysis is a simulation of gauge hole drilling, installation and overcoring. Two important advantages with the finite element approach are a more faithful representation of the conditions of HI stress measurement than approximated in theory and the capability for handling rock whether isotropic, transversely isotropic or fully anisotropic

Mar 2, 2022

By C. S. Wageman

Staying competitive in the highly aggressive Powder River Basin is a challenge facing all operators. Any advantage that a mine utilizes to improve productivity and reduce costs could mean the difference in the tight spot coal market. Technological advances in mining equipment and data acquisition at the Eagle Butte Mine in Gillette, Wyoming result in productivity gains and increased maintenance awareness. A new overburden haulage truck fleet with an onboard payload and fault monitoring system interacts via telemetry with the loading shovel and PC's located in production and maintenance offices, enabling staff to monitor production and maintenance on a real-time basis. This paper will describe the system and highlight the benefits realized as a result of its implementation.

Jan 1, 1996

By A. Iannacchione

Most legacy drift mines entered the coal reserve from outcrop and developed up-dip. The Surface Mining Control and Reclamation Act of 1977 changed this way of mining, requiring all new mines with acid- or iron-producing coal seams to be designed so as to prevent gravity water discharges from the mine. This Act requires engineered barriers to contain the mine pool. In many cases, mine layout designs focus primarily on the size and hydraulic performance of the un-mined coal barrier between the up-dip mine pool and areas where down-dip surface discharge is possible. In other cases, designs focus on preventing discharges from barriers contained within the strata surrounding the mined coalbed. This paper focuses on a detailed analysis of the factors responsible for preventing mine pool discharges to surface waters. Important factors include: mine layouts, mining methods, hydraulic head and conductivity, and geology. While the exact causes for the successes and failures could not always be determined, reasonable mechanisms are presented.

Feb 23, 2014

By Craig M. Sams

Matching mill? drives to mill power draws is a relatively new practice with the introduction of variable speed drive arrangements. Semi-autogenous grinding (SAG) mills are the focus of this paper as ball and rod mill characteristics are easily charted as charge loading and speed change. In addition, a look at types of drives available in the market and mechanical ratings is outlined to match the specifics of each drive.

Jan 1, 1991

By M. L. Free, N. Dhawan, M. S. Safarzadeh, J. D. Miller, M. S. Moats

"The drum agglomeration of nickel laterite and gold ores has been optimized through the design of experiments (DOE) using a Taguchi L16 (45) orthogonal array to determine the optimum conditions for maximizing average agglomerate size and minimizing the amount of fines. The effects of controllable operating factors including moisture content (nickel laterite ore: 34-37%; gold ore: 7-10%), retention time (2-3.5 min), drum speed (15-45% critical speed), drum load (nickel laterite ore: 8-32 %; gold ore: 6-22%) and acid concentration (150-600 g/L) on the performance of the agglomeration process were studied.For nickel laterite ore, maximum average agglomerate size and minimum percent fines (-1 mm) occurred under the following conditions: drum load (23.7%), moisture (36.5%), time (3 min), drum speed (30% critical speed) and acid concentration (150 g/L). Under the studied nickel laterite ore conditions, the most effective parameters for maximizing average agglomerate size and minimizing the amount of fines were found to be drum load and acid concentration, respectively. Drum speed had a statistically significant effect on minimizing the amount of fines. Maximum average agglomerate size and minimum percent fines (-1 mm) for gold ore occurred under the following conditions: drum load (19.3%), moisture (8.5%), time (2 min 15 s) and drum speed (40% critical). The most significant factors for maximizing average agglomerate size and minimizing the amount of fines for gold ore were found to be drum load, time and moisture.IntroductionSeveral heap leach operations have experienced problems in terms of poor recovery due to percolation issues caused by low-grade complex ores, tailings and clayey deposits. Poor percolation can lead to low metal extraction due to solution channeling or the development of impermeable/dead zones within the heap (Dhawan et al., 2012; Kappes, 2005). Improper heap building practices such as the use of loose agglomerates and inadequate attention toward the presence of clay minerals have been among the main reasons for percolation issues. During the transport of ore material, severe segregation of the material can occur. To overcome percolation problems, a major improvement was made through the introduction of agglomeration prior to ore placement. If the ore particles and agglomerates are of similar size, segregation can be avoided to a great extent (Dhawan et al., 2013; Kinard and Schweizer, 1987; McClelland and van Zyl, 1988). Agglomeration improves the uniform percolation of solution through ore heaps and is applicable to many ores, wastes and milled tailings (Bouffard, 2005; Dhawan et al., 2013). Manning and Kappes (2005) reported agglomeration/ stacking accounts for ~14% of the total heap leaching operating cost. The cost of binder is a primary contributor toward the total cost. Also, the lack of consistent quality control tests for agglomerate often leads to operational problems. The details are mentioned elsewhere (Dhawan et al., 2013). Considering the significant contribution of the agglomeration/stacking step toward the total heap leach operating cost, it is appropriate to study the agglomeration behavior and its optimization for two different ores. The reason to study the same parameters for different ores is the fact that significant variability in the agglomeration behavior of different ores has been reported to exist in industrial operations."

Jan 1, 2015

By R. J. Sheets

In 2009 the Gold Quarry open pit mine, located 11 km northwest of Carlin, Nevada, USA, experienced multiple large-scale slope instabilities of the upper east highwall that reduced gold ore extraction for nearly 18 months. The slope instabilities occurred within a weak, consolidated sedimentary sequence that exhibits strength characteristics that are transitional between soil and rock. Instability initiated as mining exposed the lower clay-rich sub-units of the Carlin Formation (Fm.). This deformation created preferential flow paths that allowed groundwater from the upper sandy sub-units to infiltrate low permeability clay-rich sub-units, thereby enhancing deformation of the slope toe which in turn destabilized the upper portion of the highwall. The outcome was a 160 m high slope instability that had a lateral run-out of 850 m. The effort to return the pit to ore production required both the geotechnical and hydrogeological investigations and the preliminary remediation mining activity to be concurrent. This approach required the development of detailed safety procedures and a requirement to modify the remediation design as new results were obtained. An initial challenge was to mitigate a near vertical, 90 m headscarp with blast induced, localized slope failures. Back-analyses applying numerical modeling indicated that the failure surface did not coincide with initial interpretations based on field observations; drilling results eventually confirmed this alternative failure geometry. The final remediation design incorporated shallower slope geometries and an approximately 3 Mt buttress along the base of the Carlin Formation and bedrock contact to reinforce the lower clay-rich sub-units. The outcome is a stable highwall within the Carlin Fm. following nearly ten years of repeated slope instability, and an example of the necessity to conduct appropriate geotechnical and hydrogeological studies during the early stages of a new layback evaluation or new open pit development.

Feb 23, 2014

By O. Ozdemir

Soda ash, an essential raw material for major industries, such as the glass, chemicals, soap and detergents, pulp and paper, mining and water treatment industries, is traditionally produced by chemical and thermal treatment of trona ore. The treatment processes for trona ore are not only chemically expensive but also energy intensive. Hence, the production of a high-purity trona concentrate at a lower energy and operating cost is of considerable interest to the trona industry. In this study, we describe a possible two-stage process for concentrating trona ore, involving dry magnetic separation followed by flotation, to remove insoluble impurities from the trona ore. The results showed that a trona concentrate of 91.7% purity with a recovery 91.1% can be obtained by two-stage magnetic separation, which could be further improved to 98.1% purity at a recovery of 83.8% by subsequent flotation of the non-magnetic trona product. The purity of trona concentrate is limited by the particle size and impurity content of the trona ore. The operating parameters for magnetic separation and flotation have been identified to obtain an acceptable quality concentrate.

Jan 1, 2011

By P. Amelunxen

Over the past several years, the combination of higher energy and steel costs and the recent commercial deployment of high-pressure grinding rolls (HPGR) technology in hard rock mining have led many multinational mining companies to evaluate the suitability of HPGR technology for their particular comminution circuits. HPGR technology is perceived to require a higher capital investment while delivering lower long-term operating costs. This paper undertakes a critical evaluation of this perception. By evaluating the capital and life-of-mine operating costs of competing circuit designs for soft, medium and hard ores, the HPGR break-even point can be identified, at which the incremental capital cost of an HPGR circuit is equivalent to the net present value of the projected operating cost reductions. For ores with hardness parameters above the break-even point, HPGR circuits could offer economic benefits, while for softer ores, SAG mill/ball mill/pebble crushing (SABC) circuits are likely to be more economical and energy efficient. This evaluation considers both an SABC reference circuit and a traditional stage crushing configuration. Other influential factors are also discussed.

Jan 1, 2011

By Jae-Chun Lee, Sadia Ilyas

"The present study was carried out to develop an economically feasible and environmentally friendly technique to extract metals such as Al, Fe, Cu, Zn and Ni from electronic scrap by employing Penicillium chrysogenum strain KBS3. Studies were carried out in various leaching modes, including one-step leaching with combined growth and leaching phases (Mode 1), two-step leaching with alternative growth and leaching phases (Mode 2), spent medium leaching with separated growth and leaching phases (Mode 3), leaching with fresh growth medium without fungal culture (Mode 4), leaching with deionized water (Mode 5) and leaching with commercial organic acids (Mode 6). The main lixiviants produced in leaching Mode 1 were citric, tartaric, oxalic and gluconic acids in concentrations of 12, 2.5, 1.8 and 152 mM, whereas in leaching Mode 2, the concentrations were 15, 0.5, 1.0 and 1,162 mM, respectively. In leaching Mode 3, 63 mM citric acid, 23 mM tartaric acid and 29 mM oxalic acid was observed. At 5% pulp density, both leaching Modes 1 and 2 showed similar metal extraction yields from the electronic scrap at 35º C. Approximately 96% Al, 98% Zn, 48% Cu, 25% Fe, 66% Pb and 73% Ni were extracted in leaching Mode 1 in 14 days. In leaching Mode 3, 85% Al, 81% Zn, 97% Cu, 22% Fe, 50% Pb and 63% Ni were extracted in 14 days. The extraction yield of Cu was much lower in leaching Modes 1 and 2 (48- 50%) than in leaching Mode 3 (97%), as well as in leaching Mode 6 (98%) with organic acids, including citric, tartaric, oxalic and gluconic acids.IntroductionTechnical innovations in electrical and electronic equipment with new functionalities and designs stimulate consumer purchasing and lead a rapid increase in the production of waste materials. Terazono et al. (2006) have reviewed the data on electronic waste generation in different parts of the world. Studies by Bertram et al. (2002) have also affirmed that waste electrical and electronic components are the fastest growing waste category, which emphasizes the need for efficient recycling strategies. The recycling of electronic waste is an important subject, not only from the perspective of waste treatment, but also from the perspective of the recovery of valuable materials. However, the recycling of electronic scrap is still limited, due to the heterogeneity of the materials present in the products (Veit et al., 2005).Bioleaching-based processes offer a number of advantages over conventional pyro or hydrometallurgical methods (Lee et al. 2007; Lee and Pandey, 2012). These advantages include simple, inexpensive (in some cases) and ecofriendly approaches and the generation of less active leach residue relative to other metallurgical processes. Although biohydrometallurgical processes have been successfully applied to the leaching of metals from ores (Olson et al., 2003; Rawlings, 2002), data pertaining to the application of these processes for the extraction of electronic scrap are still scarce. Recently, a few studies have been undertaken for the extraction of metals from electronic scrap/ printed circuit boards (Brandl et al., 2001; Faramarzi et al., 2004; Ilyas et al., 2007; Ilyas et al., 2010). These studies were conducted with mesophilic chemolithotrophic bacteria (Acidithiobacillus ferooxidans and Acidithiobacillus thiooxidans), cyanogenic bacteria (Chromobacterium violaceum) or moderate thermophilic bacteria (Sulfobacillus thermosulfidooxidans). However, compared to bacterial leaching, fungal leaching has several advantages, including (i) the ability to grow at a higher pH, thus making it more suitable for the bioleaching of alkaline solid waste; (ii) a generally faster leaching process with a shorter lag phase and (iii) the chelation of excreted metabolites (e.g., organic acids) with metal ions, thus reducing toxicity to the biomass (Burgstaller and Schinner, 1993; Aung and Ting, 2005)."

Jan 1, 2015

By Subhash B. Bhagwat

No economic activity would take place without human ingenuity, driven by our needs and wants. Economic activity is made possible by the energy from fossil and other energy sources, our technological hardware, the buildings and infrastructure made from materials such as metals, plastics, wood, water, and numerous industrial minerals. Industrial minerals are difficult to define; however, they generally include utilitarian minerals other than metals and fuels. Some of the industrial minerals form an exception to this categorization and, as explained elsewhere in this book, belong to more than one category because of the manner in which they are used. Industrial minerals are so numerous, and their applications so ubiquitous that they often do not receive the attention given to metals or fuels. Nevertheless, without industrial minerals, many of our most fundamental economic activities such as construction of our cities and towns, control of floods, transportation of our people, the search for minerals, the smelting of metals, and the delivery of supplies of clean water would be impossible. How then do we assess the economic importance of such a variety of materials lumped together under the general designation of industrial minerals? The price per ton or the total amount consumed do not satisfactorily explain the relative value of these materials to the economy. For example, the current price of limestone is about $5/t and the price of fluorspar is about $190/t. However, nearly 1.1 Gt of limestone, valued at about $5.5 billion, are consumed in the United States annually, compared with 590 kt of fluorspar, valued at about $1 12 million. It would not, however, be accurate to conclude that the mineral with the higher total value is always more economically important. Many other questions must be answered before making judgments of this type. These questions include how many people are employed in the production, processing, and distribution of the mineral? How is the mineral used? Is it partly or entirely imported? Where do the imports come from? How is the mineral transported? Is the mineral considered critical to national security? Is there a substitute material available in case the mineral supply is interrupted? Where would the substitute be produced? What would be the basic material from which the substitute will be produced? Even when these questions have been answered satisfactorily, the economic importance of the mineral is not completely known until the consuming sectors are studied as well. For example, even though the manufacture of fighter aircraft is vital to the national security, it employs only a fraction of the number of people employed in the housing and construction industry or the automobile industry or the appliance industry. Mineral commodities consumed in these latter sectors of the economy are more significant than those consumed in the production of fighter aircraft, because nearly two-thirds of the Gross Domestic Product (GDP) depends on the purchasing power of individual consumers. In comparison, the entire defense budget accounts for only 6% of the GDP. There is no easy way to present the importance of industrial minerals to the US economy because most minerals have diverse applications and products made from industrial minerals often con- tribute to the production of other goods and services. One way of highlighting the value of a mineral would be to relate it to the GDP reported by categories such as construction, machinery, stone, clay and glass products, electrical and electronic equipment, paper and allied products, and chemicals and allied products. These GDP categories represent industries fundamental to the economy totaling $644 billion, or about 12% of the GDP in 1990. However, these categories are not convenient for discussion of the many minerals that are used in our complex economy. In a general way, minerals are the 5% of our economy that make the other 95% possible. This chapter, therefore, discusses a selected few industrial minerals to illustrate their importance to various sectors of the economy.

Jan 1, 1994

By James C. Irvine

Pea Ridge Iron Ore Co., previously Meramec Mining Co., a joint venture by Bethlehem Steel Corp. and St. Joe Minerals Corp., mines and pelletizes iron ore at the Pea Ridge mine. The Pea Ridge property, now wholly owned by St. Joe, is located near Sullivan, MO, about 112 km (70 miles) southwest of St. Louis. The ore body was delineated in the mid-1950s by St. Joe during a lead exploration program. The first test holes drilled on the Pea Ridge magnetic anomaly revealed the presence of a large magnetite deposit; further drill¬ing in 1956 and 1957 confirmed that the ore body was minable. Meramec Mining Co. was incorporated in 1957 and shaft sinking began late in the year. Pro¬duction commenced in April 1964. The ore body is overlain by about 396 m (1300 ft) of flat-bedded sediments. It is tabular, about 792 m (2600 ft) long, and up to 182 m (600 ft) thick. It dips about 1.39 rad (80°) and is of unknown depth. The ore is mainly high grade magnetite with small zones of specular hematite. The wall rock is a Precambrian rhyolite porphyry. The mine was initially started with five major levels on 45-m (150-ft) intervals. Crosscuts were driven across the ore body on 58-m (190-ft) centers. Banks of stopes were mined between the crosscuts by a modi¬fied shrinkage stoping method (Fig. 1). This was done by undercutting a 12 m (40 ft) wide by 45-m (150-ft) long block and blasting horizontal "lifts" drilled on 1.5-m (5-ft) intervals. A 20-m (65-ft) sill was left between levels which contained the slushing drift, fin¬gers, crown pillar, and adequate thickness for support. By 1971 a "lattice" of pillars had been left and mining had progressed to the point that an orderly pillar re¬covery program was necessary (Fig. 2). INITIAL PILLAR RECOVERY PROGRAM The program was started in the upper western por¬tion of the ore body, furthest from the shafts. Due to the fact that the ore body narrows in the western extremity, the stope orientation was changed to mini¬mize required development. This left pillars 18 to 24 m (60 to 80 ft) wide and up to 79 m (260 ft) in length. The area selected for the start of the program had been developed between the uppermost level at 419 m (1375 ft) below surface and the 510-m (1675-ft) level. Due to the 91-m (300-ft) difference in depth, sublevels were driven on 15-m (50-ft) intervals and the ore was taken by rather classical sublevel stoping methods (Fig. 3). This left a structure with accesses compatible with drilling with 114-mm (41/2-in.) bore drifters mounted on columns. Most holes were drilled 63.5 mm (21h in.) diam and reamed to 100 or 127 mm (4 or 5 in.). Practical depth capability was about 21 m (70 ft) for holes above horizontal and 13 to 15 m (45 to 50 ft) for holes below horizontal. The interdependence of these long pillars necessitated that several of them be blasted simultaneously, making large blasts the only practical approach. Due to the required length of such loading cam¬paigns, it was necessary to select an explosive which could stand in the hole in an underground mine for a 4 to 6 week period. After some consideration a pump¬ able water gel was selected for both uphole and down¬hole loading. This afforded a high velocity, high density explosive which could be handled in large quantities. Loading the downholes was a fairly straightforward process. The holes were lined with an 8 mil polybutylene plastic sleeve and water gel was pumped into them with a double diaphragm pump mounted on the bottom of a stainless steel tub with a 81-kg (180-1b) capacity. Potential leakage into cracked areas of the pillar was

Jan 1, 1982