Search Documents

By Jue Kou, Fazhao Sun, Jiang Liu, Cuili Gui, Baoqiang Yu, Chunbao Sun

A novel special magnetic separator was developed based on the special properties of precious metal-bearing alloy in highgrade nickel matte. The recovery of Au, Pt, and Pd was 77.79%, 84.79%, and 81.79% respectively at optimum operation conditions of magnetic separator feed of 2.5t/h, pulp density of 45%, and flush water of 1.5t/h, and the recovery significantly improved comparing with normal magnetic separator. Magnetic field simulation of the special magnetic separator indicates that magnetic intensity of 0.6 T can be generated on the surface of magnetic drum, which can strengthen the recovery of heavy alloy that contains precious metals. The alternate strong and weak magnetic field can also make magnetic particles rolling on the surface of drum, which will reduce the generation of magnetic agglomeration to a large extent and decrease the content of impurities in magnetic concentrate.

Jun 16, 2022

By J. A. Herbst, Y. C. Lo

This paper attempts to answer whether or not the mill performance at Bougainville could have, in fact, been predicted by the population balance approach, or whether other special considerations are required to explain their behavior. In recent studies, the plant tests were performed at Bougainville and batch tests were carried out at the Utah Comminution Center. In all tests power measurements were made and several levels of energy input to grinding were evaluated. Also, tracer tests were performed for mill residence time determination. The performance of Bougainville's 5.5x6.4-m mill has been very successfully predicted by population balance methods. The prediction errors are only about 1% on product size distribution and 4% on power with a mill volume scale-up of 3790:1. It is significant that this approach will reduce the risk of failure in large mill design that has been recognized in traditional methods.

Jan 1, 1987

By V. Nasri, S. Rashidi

The Baltimore Red Line Project is a proposed 22.7-km (14.1-mile) long east-west light rail transit (LRT) line envisioned to connect the areas of Woodlawn, Edmondson Village, West Baltimore, downtown Baltimore, Inner Harbor East, Fells Point, Canton and the Johns Hopkins Bayview Medical Center Campus. The Red Line LRT System has two tunnel segments - the Cooks Lane Tunnel (CLT) and the Downtown Tunnel (DTT). The CLT segment is roughly 1,920-m (6,300-ft) long. It commences at the west portal located at the highway ramp for I 70 (to be removed) and terminates at the east portal that is at the intersection of Edmondson Avenue (U.S. Route 40) and Glen Allen Drive. This segment of the project consists of the following construction components: approximately 1,458 m (4,786 ft) of tunnels, 143 m (469 ft) of cut-and-cover tunnel, and 318 m (1,045 ft) of retained cut (U) section. The approximate horizontal alignment for the Red Line LRT Project is shown in Fig. 1.

Jan 1, 2014

By S. W. Nicholson, L. G. Woodruff, K. J. Schulz, W. E. Cannon

The 1.1 Ga Midcontinent rift of North America has many similarities to the geology of the Voisey's Bay region in Labrador and the geology of the Noril'sk region in Siberia. These similarities include the hosting of large volumes of sulfur- undersaturated and trace-element-enriched basalt, having igneous centers characterized by crustal contamination, being characterized by metal depletions in some mafic units (an indication of prior sulfide segregation) and having known occurrences of Ni-Cu sulfide mineralization. These similarities along with new geophysical data and refined models for Ni-Cu sulfide deposits suggest that the Midcontinent rift probably contains undiscovered Cu-Ni [±] PGE sulfide deposits, some of which could be the size and grade of a Voisey's Bay or Noril'sk deposit. In particular, intrusions and related feeder systems that occur in northern Michigan and Wisconsin, as well as to the southwest along the rift margin, deserve serious examination.

Jan 1, 1999

By Allen G. Taylor

High-value materials, such as gold, platinum and other precious metals, are subject to loss through unauthorized removal from mines, smelters, refiners and other places where such materials are processed. A study by Gastrow (2001) determined that between 1994 and 1998 an average of 603 kg/a (1,330 lb/year) of gold was stolen from South African mines and subsequently recovered. This does not include the gold that was stolen but not recovered. At 2011 prices, 603 kg/a (1,330 lb/year) of gold would be worth approximately $33 million. Mine security personnel believe that the unrecovered stolen gold far exceeds what is recovered (Gastrow 2001). Traditionally, metal detectors have been used to screen personnel leaving secure areas to discourage such unauthorized removal. However, with the current near-record prices of gold, platinum and other precious metals, it has become worthwhile for people exiting a facility to walk out with quantities of product that are too small for ordinary metal detectors to register, resulting in substantial financial losses.

Jan 1, 2012

By HASSAN E. EL-SHALL, AYMAN A. EL-MIDANY, KERRI-ANN A. HUE

Modifying the hydrophobicity of clay is necessary to accommodate large mycotoxin molecules such as zearalenone (ZEN). In this study, tricaprylmethylammonium (TCMA) chloride and common corn oil were used to modify clay. The results indicate that more than 90 percent of ZEN could be removed using clays modified by TCMA and corn oil at acidic and neutral pH due to the expansion of intergallery spacing as a result of TCMA surfactant intercalation within the clay-forming layers. The removal percentage depends on the pH and amount of clay used. Complete removal can be achieved at acidic pH and small clay amount.

By E. Valdiviezo, J. F. Oliveira

Adsorption of residual flotation reagents onto equilibrium fluid cracking catalysts is a promising method of purification of flotation process water. In the present paper, adsorption of sodium dodecyl sulphate (SDS), dodecyl ammonium chloride (DAC) and sodium oleate onto a spent catalyst from petroleum industry was studied by analysing the residual concentration of the surfactant after contact with the zeolite catalyst. The adsorption of the DAC was rather low but SDS and sodium oleate presented a high affinity for the catalyst surface. The loading capacity was 4.2 kg/ton for SDS and 5.5 kg/ton for oleic acid. After the treatment of the loaded catalyst with a HCI 1 N solution these surfactants are desorbed and the catalyst may thus be regenerated. This would be an additional advantage to its low cost, not to mention its condition as a discarded product and its availability in large tonnages.

Jan 1, 1995

By D. J. Simbi, T. R. C. Fernandes, M. Nyamhunga

The recovery of P2O5 from a 90-95% minus 45 microns phosphate slimes sample was carried out in a 5.08-cm internal diameter and 549-cm high flotation column cell. The influence of the feed rate, feed percent (%) solids, and frother dosage on the recovery was investigated following a truncated cubic 3 level by 3 variables experimental design. Two three-variable interactions of feed rate (-l)/feed percent solids (+l)/frother dosage (-1) and feed rate (-l)/feed percent solids (-1)/ frother dosage (+I) gave the region of optimum column performance: recovery (52.60-74.50%), mass yield (15.68-18.80%), and concentrate grade (22.87-31.2196). The collector dosage also showed a significant influence on the column performance. The high reagent consumption relative to the current plant levels points to the need for the removal of ultrafine particles (<10 µm).

Jan 1, 1999

By William E. Foreman

The results of the electrokinetic study of the activation of quartz by divalent cations showed that the charge reversal was related to the point at which the cation hydrolyzed. The reversal was not due to the presence of solid hydroxide at the surface of the quartz but due to the charged ions in the solutions. The charge reversal for beryllium at a log molar concentration of 1x10-4 was observed at pH 5 and 9. The quartz was positively charged between a pH reading of 5 to 10. Magnesium at the same log molar concentration did not show a charge reversal from pH 2 to 12. The probable cause of the charge reversal was due to the ionized Be3 (OH)3+3 or Mg (OH)+ . Variations in the electrokinetics of quartz were minimized by heating the sample to 300° C.

Jan 1, 1968

By Jack Bradbury

The open stope room and pillar method of mining is used throughout Ozark Lead Company&apos;s underground mine located at Sweetwater, Missouri. This method of mining produces an approximate overall ore extraction of 80%. Pillar recovery, on a limited and experimental basis, was started in January of 1979 to determine the maximum size underground opening that could be mined safely. Monitoring the roof and surrounding pillars for potential failure during this pillar recovery process was accomplished by utilizing a simple rod extensometer to measure roof sag. Boreholes 7.5cm in diameter were drilled 3.5m into the roof to spot any separations or cracks that might have propagated between the bedded layers of rock. Underground openings 85m in length by 46m in width have been mined successfully without roof or surrounding pillar failure. Continued measurements to establish long term results will be necessary.

Jan 1, 1981

By D. P. Patil, T. C. Rao, J. P. Barnwal

Factorial design of column flotation experiments was used to understand the main and interactional effects of the column parameters. In the experiments, the air flog rate, the wash-water, flow rate and the froth depth were varied at two levels. Analysis of the results showed that an increase in airflow rate had a deleterious effect on the grade of the concentrate, whereas, an increase in froth height increased the grade. The interactions between airflow and wash water and between airflow and froth height were significant with respect to grade of the concentrate. These results demonstrated that, from an ore containing 12.76% P2O5, it is possible in a single-stage flotation column to obtain a concentrate containing 31 % P2O5 (10.6% Si02) with a recovery of 94%, thus reducing the number of cleaning stages that would be required if conventional flotation cells were used.

Jan 1, 1997

"Iron ore is the source of primary iron for the world’s iron and steel industries. Its production can be reported as crude ore, usable ore or iron content of ore. Historically, the U.S. Geological Survey (USGS) used reported crude ore production from China in tabulations of world iron ore production while other countries have typically reported their production in terms of usable iron ore. When China’s crude ore production was tabulated with usable ore production from other countries, world iron ore production totals have been overestimated by 10 percent to a high of content and may include products such as concentrates, direct-shipping ore, pellets, and sinter.• Iron content, also referred to as metal content or grade, denotes the amount of elemental iron in the crude or usable ore.BackgroundIron ores consumed in the steel industry typically require an iron content greater than 58 percent before being considered commercially usable. Iron ores that are not commercially usable must undergo beneficiation to raise the iron content. Approximately 98 percent of the world’s usable iron ore production is consumed in blast furnaces to make pig iron, which is further processed to make steel.High-grade iron ore mines can supply usable iron ore, known as direct-shipping ore, to blast furnaces, with minimal physical processing and no beneficiation. With direct-shipping ore, the reported production for crude ore and usable ore are the same. Ore from low-grade deposits must undergo beneficiation to increase the iron content before it can be used by the steel industry. In this instance, the mined material is called crude ore and post-beneficiation concentrates are called usable ore; the amount produced will be less than the crude ore amount. With the notable exceptions of countries such as Australia and Brazil, most of the world’s iron ore deposits are low-grade and require beneficiation."

Feb 1, 2017

By Lok W. Home

INTRODUCTION Today, raise drilling (boring) has become the stan¬dard method of raising throughout the Western world. It is estimated that the majority of raise footage com¬pleted in 1977 was accomplished by the raise drilling method. Extensive replacement of the drill and shoot system by mechanized raise drilling has occurred be¬cause users have recognized one or more of the follow¬ing advantages. In a direct cost per meter comparison, mechanized raise drilling is economically more attractive than drilling and shooting. Mechanized raise drilling offers improved personnel safety over the drilling and shooting method. Mechanized raise drilling is a faster and more predictable method for excavation than is drilling and shooting. The raise cost per unit of length becomes less as the raise length increases, offering greater flexibility in the overall design of mines. Mechanized raise drilling provides a substantial reduction in labor requirements. 6) Mechanized raise drilling improves the working environment. 7) Mechanized raise drilling improves the rock in¬tegrity of round, unblasted raises. Increasing acceptance of the raise drilling technique is enhanced by continuing equipment development. Today, a wide range of machines and capabilities is available, machine drive systems have been improved, reliability has been increased, and cutter technology is being improved quite rapidly. Table 1 lists the four major manufacturers of raise drilling machines, cutters, and reamers, together with the approximate number of machines that each company had in operation at the end of 1977. Although Reed and Smith are major suppliers of reamers and cutters, they do not manufacture the drilling machines. Four or five other relatively minor suppliers have built machines, reamers, and cutters for raise drilling, but they did not have a substantial num¬ber of machines in the field at the end of 1977. MACHINES FOR MECHANIZED RAISE DRILLING There are three principal arrangements for making machine-bored raises. They include the use of standard raise drills, reversible raise drills, and blind-hole or box¬hole raise drills. Standard Raise Drills The standard raise drilling machine is set up on one mine level or on the surface, and a pilot hole is drilled from that level or surface to a level below. When the pilot hole has been drilled, the raise then is reamed back from the lower level to the upper level or the surface. This arrangement is illustrated in Fig. 1. Reversible Raise Drills The reversible raise drilling machine is set up on a lower level of the mine, and a pilot hole is drilled up¬ward to a higher level. The raise then is reamed back from the upper level to the lower level. This arrange¬ment is illustrated in Fig. 2. The machines used for this type of raise drilling normally are capable of being used as standard raise drills. Blind-Hole or Boxhole Raise Drills The blind-hole or boxhole raise drilling machine is set up on a lower level of the mine, and a full diameter raise is bored to a higher level without the use of a pilot hole. This type of machine is illustrated in Fig. 3. Drill Recommendations If access to upper and lower mine levels is equal, the standard raise drill should be used. The complexity of the equipment and associated handling procedures for boxhole drilling far outweigh any mechanical advantage or reduction in the number of operations, provided that access to an upper level is available. If there is good access to a lower level but only limited access to an upper level, the use of a reversible raise drill should be considered. If there is no access to an upper level, a blind-hole or boxhole raise drill is the only practical mechanized system. MACHINE SELECTION There are six major considerations in selecting a machine for raise drilling. These include operating range, cutter loading, machine structure and main¬tenance, drill string configuration, drive system, and automated controls. Operating Range As shown in Table 2 and Figs. 4 through 6, raise drilling machines are available for a wide range of hole sizes. Standard raise drill ratings range from raises of 0.9 m (3 ft) diam and 120 m (400 ft) length up to raises of 3.5 m (12 ft) diam and 900 m (3000 ft) length. Boxhole raise drilling machines are available for raises ranging from 0.9 m (3 ft) to 2 m (6 ft) diam with lengths up to 90 m (300 ft). Table 2 lists, among other criteria, the torque and thrust of typical machines; torque and thrust are the main criteria for analyzing the capacity of a machine. The raise sizes shown in Table 2 assume a condition of medium hard to hard rock formations and optimum cutter loading. The recommended raise size for a given machine can be exceeded when raising softer rock formations or when the operator is willing to accept a lower level of performance; the performance is related directly to the 1093

Jan 1, 1982

By Brian Gettinger, Jim Schlaman, Alston Noronha

"INTRODUCTION The public understanding of green solutions today is based on the definition of sustainability adopted by the Brundtland Commission (World Commission on Environment and Development) in 1987: “development that meets the needs of the present without compromising the ability of future generations to meet their own needs.” Over time this initial definition evolved to identify three distinct factors impacting sustainability that are often referred to as the “Triple Bottom Line”: Economic, Environmental and Social. The triple bottom line approach seeks to drive outcomes that create maximum value for all stakeholders. In the last ten years purveyors of water and wastewater tunnel solutions have found themselves on the wrong side of a politically polarizing issue in the crosshairs of politicians, environmental activists and community groups branding tunnels as expensive, “gray” and not-sustainable. Tunnels under design were stopped and large planned tunnel programs were delayed or canceled. Therefore being sustainable and “green” is not simply using natural vegetation, but creating an asset that meets current and future needs and will not become a future liability. As this paper will discuss, tunnel projects embody a sustainable triple bottom line project well, are equally sustainable as green infrastructure, and have begun to gain awareness for their sustainability. GREEN INFRASTRUCTURE CHANGES TUNNELING LANDSCAPE The green movement quickly swept across the nation in the mid to late 2000’s and was a hot topic in the media and at all the local, regional and national industry conferences. Politicians espoused the benefit of green infrastructure including job creation, urban renewal, aesthetics, property values economics and sustainability. The political microscope was focused the closest on stormwater and wastewater management, particularly in communities responding to combined sewer overflow (CSO) consent decrees from the Environmental Protection Agency (EPA). As communities with CSO problems evaluated their long term control program (LTCP), local government officials and planners began to balk at the huge price tag required for compliance and began looking for alternatives. “Green” infrastructure was proposed as lower cost solution that could be used to offset capital-intensive “gray” infrastructure like new sewers, storage tanks, tunnels, and treatment facilities. In addition, including green infrastructure in a previously negotiated LTCP required a reset on the entire planning process, additional studies and more planning which would push capital investment further off into the future, subsequently delaying unpopular user rate increases. As a result, tunnel projects as well as trenched conveyance and treatment plant projects that had not yet started construction were stopped, delayed or substantially changed."

Jan 1, 2016

By R. Mittler

Over 100 saprolite samples from Turkey Hill Gold Mine, Lumpkin County, Georgia, were analyzed (-80 mesh) for As, Au, and Sb. Maximum values are 16.2 ppm As, 7.9 ppm Au, and 29.1 ppm Sb. Results show trace element content of saprolite varies with topography: ridge top samples show a pronounced decrease in Au and Sb, and to a lesser degree in As, whereas, slope and valley samples have anomalous Au and Sb concentrations, with no discernable pattern for As. Statistical analysis shows strong correlation between Au and Sb and none between Au and As. This study will serve as a model for gold exploration in deeply weathered terrains with variable relief.

Jan 1, 1987

By Josh Savit

Corporate responsibility already encompasses safety and compliance. No longer will companies be able to use differing standards of care to miners based on the country in which they are working. This is not only an issue of social license, but one of global risk management.

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Mine explosions are one of the most concerning risks related to underground coal mining, as a single gas explosion can cause injuries and fatalities among miners. Underground infrastructure seals and build-in-place (BIP) refuge alternatives (RAs) are employed to isolate an area from active workings to mitigate coal mining-related accident risks. They are designed to withstand blast pressures from a possible accidental detonation of the contained gas or a coal dust explosion. Crosscut seals and BIP RAs, typically consisting of steel-reinforced concrete, are prone to strong convergence and have a significant leakage potential due to high convergence damage near mined-out areas. The roof-to-floor convergence can change the structural integrity of these structures, and altered structural integrity can lead to less explosion resistance capability. Hence, a thorough analysis is needed to further understand their explosion response under various strata conditions.

Jul 1, 2023

By James R. Aggson

This paper summarizes the research effort that was conducted as part of a cooperative agreement between the U.S. Bureau of Mines, Denver Mining Research Center and the Pittston Company. The objective of this investigation was to further the understanding of the floor heave ground control problems that have plagued underground mining of the Beckley coalbed in southern West Virginia. Floor heave is both economically and structurally undesirable. Floor heave is accompanied by a redistribution of stresses and loads that are associated with an underground opening. This redistribution of stresses may cause roof or pillar problems that otherwise would not have occurred. The floor heave that occurs in the Beckley coalbed is not cons1dered to be caused by "squeezing" or plastic flow of the materials involved. The "squeezing" type floor heave is normally associated with relatively weak floor members that contain significant amounts of clay mineralization. The floor members in the Beckley coalbed are competent, relatively strong materials which fail in a manner that can best be described by the term "buckling." This buckling-type failure is indirectly related to the time-dependent deformation properties of the materials involved, but is considered to be more of a slender column, or panel, type failure than a "squeeze" or "flow"-related failure. The Beckley coalbed has had a history of floor heave ground control problems. The Glen Rogers mine, which opened in the 1920&apos;s, experienced extensive floor heave. In a report dated April 1929, James P. Keatley of the West Virginia State Department of Mines described the floor heave in the Glen Rogers mine. Several observations listed in the Glen Rogers report that appear to be consistent with current observations follow: 1. Water plays no apparent part in the floor heave process. 2. No evidence of gas has been found in the floor. 3. The thickness of the overburden, which varies from 183 to 396 m (600 to 1300 ft), has no relationship to the floor heave. In the conclusions of the 1929 report on the Glen Rogers mine, Keatley states, "A statement in brief as to the cause (of floor heave) would lie that an undetermined natural condition doubtless augmented by former and present mining methods causes the bottom to heave." As this report will show, Mr. Keatley&apos;s insight into the problem was most accurate. The "undetermined natural condition" is the existence of a biaxial, horizontal, compressive stress field. This stress field is in excess of that which would be expected from gravity loading. This stress field and the material properties of the floor rock combine to cause the floor heave that has been experienced. The floor heave that occurs in the Beckley seam generally occurs as arching, with a tension fracture, near the center of the floor span or as a break near the rib followed by vertical deflection (of the floor) at the rib and sloping of the floor across the entry. Examples of the floor heave are shown in Figures 1 and 2. The two types of floor heave are merely different manifestations of the same basic failure mechanism. When the entries experiencing floor heave were identified on a map of the mine under investigation, it was apparent that there was a relationship between the floor heave and the direction of the entries. The main entries, which are used for ventilation and haulage, experienced the majority of the floor heave. This directional relationship suggested a directionally related loading mechanism, or more specifically, a biaxial, horizontal stress field that exceeds what would be expected by gravity loading. Since the main entries were oriented at a bearing of N25oW, it was hypothesized that the maximum compressive component of the horizontal stress field was at 90° to these entries or at a bearing of N65oE. An in Situ testing program was developed to test this hypothesis and investigate the floor heave problem.

Jan 1, 1978

By Patti J. Best

The Southern Powder River Basin (SPRB) now commands 30% of the US utility, coal market due to the region&apos;s low mine production costs, competitive rail rates and low sulfur content. In 1997, production exceeded 240 Mt (265 million st). This was an in¬crease of 104 Mt (115 million st) since 1989 and 4.5 Mt (5 million st) above 1996. Continued growth is expected as the second phase of the Clean Air Act Amendments (CAAA) approaches. This growth will be the greatest in the southern part of the Basin where coal quality is higher. Coal characteristics SPRB coal is classified as subbituminous due to its low heating value and high moisture content. The coal is characterized by low sulfur and ash contents, low ash fusion temperatures and high reactivities. In 1997, the average heating content was 8,593 Btu/lb, with an average sulfur and ash content of 0.79 lbs S02/million [ ] Btu and 5.13%, respectively. The distinguishing characteristic of SPRB coal is its low sulfur content. Most SPRB coal contains less than 1.2 lbs S02/million Btu. This is the approximate definition of "compliance" coal for Phase II of the CA AA. Much of the coal, particularly in the southern part of the Basin, is referred to as "super-compliance" coal due to SO2 contents of between 0.4 and 0.7 lbs SO2/million Btu. The SPRB is divided into three geographic clusters based on coal quality. Mines located in the southern part produce coal with the lowest average sulfur content and highest heating content, almost 400

Jan 1, 1998

By Alexander N. Winchell

"Location: The Menominee district has been described geologically in several units, because the known iron-bearing formations of the larger region are not a really connected. From the commercial and mining standpoint, however, the district em¬braces, all that territory extending from a point about five miles east of Vulcan to a point a few miles west of Iron River, an east-west distance of about fifty miles, and from a line about two miles south of Vulcan to one ten miles north of Crystal Falls, a north-south distance of about thirty-five miles. This area is largely in the State of Michigan, but includes more than two hundred square miles in Florence County, Wisconsin. The chief towns of the district are Vulcan, Iron Mountain, Iron River, and Crystal Falls, in Michigan, and . Florence in Wisconsin. The Wisconsin portion of the district has not produced a large portion of the output of the area.History: The earliest reports of iron ore in the Menominee district were made by J. W. Foster and S. W. Hill, who conducted a geological exploration from Lake Superior to Green Bay in the fall of 1848. It is a remarkable fact that in spite of their plain statements regarding their discoveries, these state¬ments were apparently forgotten for a period of nearly twenty years. Foster states that ""about two miles southeast of the lower falls (of the Twin Falls on the Menominee River) near Sec. 30, T. 40 N., R. 30 W. there is a large bed of specular iron ore associated with the talcose and argillaceous slates. It makes its appearance on the north side of the Lake and can be traced a mile and a half in length and in places is exposed one hundred feet in width."""

Jan 1, 1920