Search Documents

By C. N. Bensley, S. K. Nicol, R. Lamb, G. W. Kidd

Flotation circuits in the metalliferous industry recover high value concentrates from very fine (minus 0.lmm), low grade, slow-floating feeds. Flotation columns acting as final cleaners within these circuits offer the benefits of higher grade concentrates, reduced circuit complexity, improved control and reduced power consumption. By contrast, in the coal industry, these benefits have not been realised, principally because columns are not well suited to the treatment of conventional coal flotation feeds (minus 0.5m). However, this does not imply that columns do not have a place within the coal industry, rather that they must be applied in a role where all the unique advantages of column flotation can be of benefit. The development of a commercial scale column to recover discarded ultrafines from the Riverside preparation plant of BHP-Utah Coal Limited is discussed. Particular emphasis is placed on the column design features pertinent to the recovery of ultrafine coal. Pilot and commercial scale column performances are compared. The results of the commercial scale testwork indicate that a full installation at the 5.5 MTPA Riverside plant would annually recover additional coal worth $US 6.6M.

Jan 1, 1988

By Diler Katircioglu-Bayel

This study aims to investigate the effect of combined mechanical and ultrasonic milling on the size reduction of talc. Firstly, the talc sample was wet ground in a stirred media mill for five different times (30, 60, 90, 120, and 150 min), and the optimum result was subsequently achieved with treatment by ultrasonication. The effects of amplitude (20, 35, and 50 μm), solid content (2.5, 5, 7.5, and 10%), and sonication time (60, 120, and 240 min) on the sizes of the final product were investigated. The pre-milling by wet grinding caused a decrease in the grinding resistance of talc. Sequential ultrasonic treatment, which was applied to the talc sample, generated smaller particles in comparison to those acquired by stirred media milling alone. Experimental results were assessed based on the product particle size (d10, d50), reduction ratio, and specific energy consumption. Submicron particles prepared by ultrasonic treatment were perfectly stable compared to stirred media milling alone as investigated in terms of particle size. In addition, the effects of mechanical and ultrasonic milling on structural properties of talc particles were characterized by XRD analysis.

By A. Gene Collins

The demand for lithium may increase because of its potential use id lithium batteries and in the generation of electrical power by fusion. Therefore, lithium abundance in some United States oil-field brines was surveyed. Oil-field brines from numerous locations were found to contain more than 100 mg/l lithium and several exceeded 500 mg/l. An area of 25,000 km2, with a reservoir thickness of 60 m, an effective porosity of 5 percent, and a brine with a specific gravity of 1.2 containing 100 mg/l of lithium, contains about 0.75 x 106 tonnes (1 tonne = 1 metric ton = 1,000 kg) of lithium in 7.5 km3 of brine. It is postulated that the brines were enriched in lithium by lithium-rich spring water or lithium leached from volcanic rocks followed by evaporation sequences.

Jan 1, 1978

By T. L. Conley, J. J. Rozek

The $2 billion (A$) Melbourne City Link Project is one of the largest and most important metropolitan road developments ever undertaken in Australia. The project involves two three-lane vehicular tunnels totaling 5 km, constructed as deep as 65 m underground. The 3.4 km Burnley tunnel is one of the world's longest three-lane tunnels. The project is being delivered under a DBOOT [design-build-own-operate-transfer] process and all design and construction is performed to ISO 9000 standards. Tunnel excavation began in May 1996, and the tunnel will open to traffic in 1999. This paper focuses on the range of construction techniques utilized during construction.

Jan 1, 1999

By J. Ainsworth, W. Trudel, L. Schutz, C. L. Bolin

Newmont mine geologists have added substantial economic value developing over 1,150 tonnes into quality surface and underground gold reserves since 1986. However, the recent 5-year gold price slump from $387 to $262 per ounce has shifted mine geologists focus to optimizing open pit profitability and developing high-grade, high cash flow and low capital development underground reserves. More than $65 million projected revenue has been added to the Gold Quarry south layback following multi-departmental model reconciliation investigations. Kriged mine polygon construction, controlled blast heave and high-quality geologic advice in selective mining will have multi-million dollar beneficial impacts.

Jan 1, 2002

By L. Eros, R. H. King

The US Bureau of Mines has funded several research and development projects in computerized mine monitoring and control. Hardware and software components have been sufficiently developed so that mine operators have been provided with an efficient means to comply with federal regulations and increase mine safety. Several cost benefits have been realized as well, particularly with increased conveyor belt haulage availability. Western Fuels-Utah Inc. approached the Bureau to assist in planning, installing, and evaluating a computerized mine monitoring and control system because of the agency's research experience in this area. The installation was planned for Western Fuel's Deserado mine, located in Rangely, CO. Since a large, complex, underground mine producing about 2.4 Mt/a (2.7 million stpy) of coal was projected, the company anticipated significant benefits in safety and efficiency through a computerized monitoring and control system. A major part of the cooperative program was to document and evaluate the system design, installation, and operation. This will assist others to adequately design, specify, install, and operate future systems. Mine description The Deserado mine plan and layout have important impacts on the monitoring system requirements. Long range plans are to produce 2.4 Mt (2.7 million st) of clean coal annually from two longwall sections and four continuous sections. Presently, two continuous miner sections operate under 213 m (700 ft) of overburden in the 2.3 to 2.5 m (7.5 to 8.5 ft) thick D seam to develop main, submain, and panel entries have developed for a longwall. These began operation in December 1986. Belt conveyors haul the coal from the mining sections to a 1.4-m (54-in.) belt located in the upper compartment of the slope. The lower compartment contains a hoist for men and material transport. From the slope, the coal moves to two 9 kt (10,000 st) raw coal storage silos, then to a 680-t/h (750-stph) preparation plant. After cleaning, a 5.5-km (3.5-mile) overland conveyor carries the coal to a clean coal slot storage and rail load-out facility. An electric locomotive then transports the coal to the Bonanza Power Plant in Utah. Allen-Bradley monitoring and control hardware and software controls the preparation plant, with two PLC-3 programmable controllers and a Process Control Industries D-1200 color graphics interface. The system operator uses three "smart" color video display units and an alarm printer for hard copy records. Originally, it also monitored and controlled the conveyors from the bottom of the slope to the top of the raw coal silos, the preparation plant, the overland conveyors, the main mine ventilation fan, and the hoist. Some of these features, though, were later transferred to the mine system.

Jan 2, 1988

By Hugh E. Cronin, Joseph J. Coluccio

The Columbia Slough Consolidation Conduit Project is a 12 ft. 0 in. inside diameter—15 ft. 4 in. excavated diameter tunnel, 8,300 lf. in length. The tunnel is divided in two parts a 4,460 lf. reach to the West and a 3,770 lf. reach to the East separated by a flow regulation structure in the middle. The project was built for the City of Portland, Oregon Bureau of Environmental Services (BES) by the Frank Coluccio Construction Company (FCCC) Seattle, Washington under a $22,600,000.00 contract starting in 1998 and completing the contract in 2000 at a total cost to the City of $25,448,000. An increase of 12.6% from the original contract. The tunnel was constructed in an alluvial sediment that ranges up to 1,500 feet thick. The sediment varies from ?ne silty sand and sandy silt (SM-ML) to coarse sand and gravel (GP-GM) with varying quantities of cobbles and boulders. Most of the tunnel was constructed above the water table although one reach of almost 1,000 lf. had water to above the tunnel crown. The contractor, FCCC, used a Lovat 15 ft. 3 in.900 hp shielded TBM with multiple doors (4) of variable opening to excavate and support the tunnel. Tunnel supports were 5 in. WF 16 lbs. per foot at 4 ft. spacing and4 in. Douglas Fir lagging. Tunnel excavation was worked in 10 hour shifts with additional equipment maintenance and repair on the off time. The original Geotechnical Design Summary Report (GDSR) established a baseline for contractual purposes of slightly over 5 boulders (between 12 in. and48 in.) per foot of tunnel. (Table 1) At the pre-bid conference, three test pits were excavated to approximately tunnel invert, one at each end of the project and one in the middle near the flow regulation structure. The test pits encountered a few boulders but did not seem to support the five boulders per foot (varied from one boulder per foot of tunnel to eight b/lf.). Subsequent to the pre-bid meeting and the test pits, BES issued any addenda which changed the baseline boulder quantity in the GDSR to 1.7 boulders per foot of tunnel (varied from0.2 to 3.5 boulders per foot) a reduction of 67% from the original baseline. It is interesting to note the two separate tunnel reaches and how they were evaluated in the GDSR. Originally the Eastern portion of the work was projected at5.08 boulders per foot of tunnel and the Western portion at 5.30 boulders per foot of tunnel for a variance of less than 5%. In the revised quantity the Eastern portion was projected at 2.01 boulders per foot of tunnel and the Western portion at 1.42 boulders

Jan 1, 2003

By Z. D. Hora, W. N. Hamilton

Introduction Some unique opportunities exist for industrial minerals in British Columbia and Alberta. The region's diversified geology, particularly in British Columbia, offers favorable environments for a rich variety of mineral resources. Many minerals have been produced for years. For some, however, the level of production is far less than the potential. Others have had production in the past, but are not currently produced. Still others are known to exist and may have been actively prospected. But they are not yet developed. In addition, a number of speculative possibilities have recently come to light. The potential significance is not fully confirmed, but is suggested in showings in favorable geologic settings. Location and geography British Columbia and Alberta are the westernmost provinces in Canada (Fig. 1). The region overlaps two major physiographic divisions of the country, the Cordillera and the Interior Plains. It also takes in a small segment of the Canadian Shield on the east. The entire territory is greater than 1.6 Mkm2 (618,000 sq miles). Most of British Columbia lies within the Cordillera, a mountainous belt some 800 km (500 miles) wide. The belt is made up of three main physiographic components, the Eastern, Interior, and Western subdivisions. The Eastern subdivision embraces the rugged, linear ranges of the Rocky Mountains, elevations between 2600 and 3300 m (8530 and 10,800 ft). They form a 100-km (62-mile) wide band straddling the BC-Alberta border and extending northwest across northern British Columbia. The Interior subdivision includes several ancient mountain ranges but is dominated by an intermountane plateau area of low relief (average elevation 1200 m or 3900 ft). The Western subdivision is dominated by the Coast Mountains (elevations between 1800 and 4000 m or 5900 and 13,123 ft). These form a band about 175 km (110 miles) wide into which are sculptured the spectacular fiords of the BC coastline. Alberta lies largely within the Interior Plains, a prairie region of low to moderate relief (elevations between 200 and 1200 m or 650 and 3940 ft) formed of nearly horizontal bedrock strata. The Plains surface rises gradually to the southwest toward the deformed belt of the Rocky Mountains, where the bedrock strata are upturned, folded, and faulted. To the east, the Plains merge with the Canadian Shield, which exposes the Precambrian crystalline basement of western Canada. The total population of the BC-Alberta region is about five million people. Minerals, forestry, and agriculture are the primary industries here. It has well developed infrastructures to service these industries. British Columbia is third among the Canadian provinces in metal mining - $1.1 billion in 1985 - and first in forest products. It is also second in hydro-electric power development. Alberta leads all provinces in total mineral production, largely due to its extensively developed petroleum and natural gas resources - $26.2 billion in 1985.

Jan 12, 1987

By E. D. Attanasi, M. W. Bultman

Most statistical measures of mineral exploration continued downward in 1986. Prospects in 1987, however, appear to have brightened for exploration as the overall economic health of the mineral industry improved. The Society of Economic Geologists (SEG) survey of US and Canadian firms documents the marked decline in US mineral exploration since the early 1980's. From 1981 through 1986, the total exploration expenditure by US firms declined by more than 73% (Fig. 1). Exploration expenditures by US firms declined by 66%%. US based professional exploration staffs were slashed by 70% (Fig. 2). Also, many firms have written off some reserves because of weak markets or have not delineated new reserves to replace production. The Canadian government reported that between 1981 and 1986 Canadian molybdenum re¬serves had declined by 30%, lead and zinc reserves by 20%, and nickel and copper reserves by 15%. The SEG survey also shows the immediate impact of the decline in the dollar on US exploration expenditures abroad. Between 1981 and 1986 the share of the exploration dollar spent by US firms outside of the country declined by nearly one-half and exploration acreage abroad declined by 69%. The downward trend of the last six years may finally be near the end as a leaner and more efficient minerals industry starts to gear up for a period of increased activity. An industry survey reported to Mine Development Bimonthly (Metals Economics Group) indicates that mining firms were expected to increase exploration expenditures in 1987 by at least 10% above 1986 levels. Worldwide expenditures for 1987 by companies covered by the report were expected to top $800 million. It is the first time since 1984 that an increase in exploration expenditures was expected. Also, the US Bureau of Land Management reported a 30% increase in new mining claims for fiscal year 1987 over fiscal year 1986. The bulk of the increase in claims was in states having intense gold exploration, particularly Washington and Oregon. Much of the optimism is undoubtedly due to the increases in metal prices that occurred in 1987. Some of these increases include gold, average price up about 20%; copper, average price up 24%; aluminum, average price up 26%; and nickel, average spot price up 20%. The SEG survey shows precious and base metals accounting for 89% of the exploration expenditures in the US in 1986, up 52% from 1981. The US Bureau of Mines estimates that 80% of US exploration activity in 1986 was directed entirely at gold (1986 Minerals Yearbook). Worldwide exploration plans indicate the continued dominance of gold exploration. New programs were announced for Ghana, Malaysia, and Indonesia. Major new exploration programs were also launched for lead-zinc sulfides in Morocco, platinum and palladium in northwest Brazil, rare earth minerals in Greenland, diamonds in Indonesia, and heavy minerals off-shore Australia. Significant gold discoveries were made at Angels Camp in Oregon; South Africa, near Potchestroom; India, in the Chitradgra district; Northern Ireland near Mt. Speerin; Chile, San Cris-

Jan 5, 1988

By Derrick Chambers, George Kevin Chapin, M. Shawn Boltz

Seismic monitoring is one of the few noninvasive technologies with the potential to provide sub-surface geomechanical information to operators of large open-pit mines. Although passive seismic data has been used to refine emerging failure geometries and provide advance indication of surface deformations in the literature, doing so reliably in an operational context is much more difficult. This is due in part to difficulties in estimating and interpreting source locations and parameters in complex, low-stress open-pit environments. Additionally, the high costs associated with implementing, operating, and maintaining deep borehole seismic networks, which are most commonly used to monitor large open pits, can be difficult to justify, especially if monitoring benefits are not readily apparent. In this study, we explore the use of a near-surface nodal seismic deployment, which is commonly used in oil and gas exploration, for monitoring open-pit mining-related seismicity on a short-term basis. A deployment of 18 geophones was conducted on the surface in and around the Bingham Canyon Mine, a large open-pit mine near Salt Lake City, Utah, USA, where we find the small seismic array can detect and locate a variety of mining-related seismic sources, even with an extremely simplified velocity model. We outline the process of creating an idealized velocity model, developing a local magnitude scale, and interpreting the observed seismicity. Of note, we analyze a sequence of mining-induced events associated with a known structure on the south pit wall. We conclude with discussion on how surface-based deployments may be used to augment, or in some cases supplant, borehole seismic networks at large open-pit mines depending on monitoring requirements and objectives.

Apr 26, 2022

By Marshall D. Himes, Erich U. Petersen

The Sheep Creek deposit near White Sulfur Springs, Montana, is a middle Proterozoic stratabound and strataform sediment- hosted massive sulfide containing 4.5 million tonnes (5.0 million tons) averaging 2.5% copper, and 0.1% cobalt in the upper sulfide zone (USZ) and 1.8 million tonnes (2.0 million tons) averaging 6% copper in the lower sulfide zone (LSZ). Mineralization is hosted in lower Newland shales and debris flow conglomerates in the graben controlled Helena Embayment of the Belt Basin. USZ mineralization is characteristically high in Cu, Co, Ni, Ba, As, Pb, and Ag. Mineralogically it consists of barite, pyrite, chalcopyrite, and tennantite with minor amounts of marcasite and various cobalt minerals. By contrast, the LSZ is higher in Cu, Ni, and Au and lower in Co, As, Pb, and Ag. Mineralogy of the LSZ consists of dolomite, pyrite, and chalcopyrite. In both zones significant amounts of cobalt, nickel, arsenic and copper are incorporated in pyrite rims. Tennantite controls the abundance of numerous trace elements in the ores. Fluid incluison data from hydrothermal USZ barite suggests that mineralization took place at temperatures in excess of 250°C, under relatively oxidizing conditions (f02 = 10-32+1) from moderately saline (1.1-3.5m), metal rich brines. The absence of barite in the LSZ suggests mineralization under more reduced conditions (f02 = 10.38+2). Mineralization was initiated following basin subsidence in excess of 400m. Contemporaneous with movement along a growth fault(s) was upward migration of hot metal-bearing fluids which permeated the loosely consolidated sediments and may have vented on the sea floor. The differences in the two zones may be explained by the effects of variations in local basin morphology and solution chemistry.

Jan 1, 1990

By G. Chi, M. C. Fuerstenau, R. C. Bradt, A. Ghosh

With increased emphasis on controlled blasting, which is the first and least-costly stage of comminution, ore grindability and plant throughput can be increased by 5% to 10%, and energy savings of up to 10% appear possible. Crushing and grinding efficiencies are presented for ore blasted under regular and adjusted field conditions. An economic analysis of drilling and blasting through crushing and grinding is presented, suggesting that cost savings approaching 10% may be achieved.

Jan 1, 1998

By J. L. Hoover, P. W. Conrad, J. Downey, S. Parrow, S. Rosenthal

The goal of the drill bit consumption study was to develop an equation(s) based on various components that affect drill bit wear and use that equation(s) to estimate the consumption of bits during production drilling. Drill bit data from various geographic locations were compiled and used to develop linear regression equations using the Microsoft Excel software package. Multiple drill bit consumption equations were developed and statistical analysis was used to verify the accuracy of those equations. The equations will allow mining companies to more accurately forecast drill bit consumption when evaluating new mine properties. This capability becomes increasingly beneficial to forecasting as the cost of consumables increases.

Jan 1, 2012

By G. L. Myers

The Fortitude skarn near Battle Mountain, NV is currently one of the largest producing gold skarns in the world. It contains about 11 Mt (12 million st) of minable ore grading 5.14 g/t (0.149 oz per st) and is the distal portion of a continuous skarn system in the Copper Canyon area centered on the Eocene Copper Canyon granodiorite porphyry. Calcsilicate compositions, opaque mineralogy, and the high gold grades are atypical of other base metal skarns (iron, Fe; copper, Cu; lead-zinc, Pb-Zn; or tungsten, W). The Copper Canyon skarn is systematically zoned from a garnet (AD 70-100) dominant, pyroxene (HD 20-45) subordinate zone, with major Cu mineralization, adjacent to the intrusive (West ore body), to a pyroxene (HD20-100) dominant, garnet (AD90-100 cores. AD 30-60 rims)subordinate assemblage, with major Au, near the distal marble front (Fortitude ore body). An extensive biotite ± diopsidic pyroxene ± kspar alteration halo surrounds the pyroxene > garnet gold-bearing skarn and represents the early stages of metasomatic alteration. Retrograde alteration is limited in areal extent and intensity, and consists of actinolite, chlorite, quartz, and prehnite. Economic gold mineralization begins in the pyroxene > garnet zone and continues to the marble front, a distance of 1 to 1.5 km (0.6 to 0.9 miles), respectively, from the plutonic contact. The opaque mineralogy in this gold zone includes pyrrhotite, arsenopyrite, marcasite, minor chalcopyrite, galena, sphalerite, argentite, hessite, hedleyite, volnyskite, and native bismuth and gold. The pyrite-pyrrhotite geothermometer yields temperatures that range from 450° C to 300°C (842° F to 582° F) and the electrum-argentite-sphalerite geothermometer yields temperatures which range from 290°C (554° F) at the marble front to about 420°C (788° F) more proximal to the intrusive. Log fS2 calculations from the sulfide assemblages yield values near - 10 with log fO2 values of about -30, in a solution of near neutral pH (5-6). Calculations of metal solubility suggest that the metals were transported as chloride complexes in the proximal skarn but that bisulfide complexes were predominant within the distal gold skarn. Relatively low oxidation states buffered by the carbonaceous to argilliceous, calcareous protolith and subsequent ferrous iron-rich skarn assemblages appear to have increased the gold carrying capacity of this large hydrothermal system.

Jan 1, 1991

By C. F. Giermak

Over a considerable period of time great interest has been shown in selective dry concentration of fine ferromagnetic particles, although it is only recently that new permanent magnetic materials have been made available to permit building of such permanent magnetic separators. It is well known that the conventional drum separator does' not efficiently separate fine materials. The centrifugal force on any drum acts in accordance with the particle size and gravity, which may beat varying magnitude-.opposite to the magnetic force, especially when the material is not closely sized. The Magnetic-Mechanical Separator (MMS) is designed for the concentration of fine, unsized magnetic materials where the percentage composition of magnetics to nonmagnetics, or the nature and texture of the materials, is such that its unique agitation and shake-out action with no centrifugal force provides greater efficiency than is obtainable by conventional magnetic separation equipment. This machine consists of a complete double belt conveyor unit with a premagnetizing Axial Pole Agitating Pulley at the feeding end of the lower conveyor belt and a special agitating concentrator magnet above the lower belt of the upper conveyor.

Jan 1, 1965

By K. L. Boyd

"Can the ever-increasing tonnages of ore and waste being mined today be accommodated simply by using bigger and better crushers? This paper reviews the latest primary crushing and large cone crusher designs. It highlights how—in addition to using the larger crushers now available—maximizing the utilization percentages in each of the four stages of the rock size reduction circuit will assist in meeting the larger production requirements of existing and new mining operations. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in the material handling flowsheet from the mine to the mill, maximizing operating hours per year. INTRODUCTION Are larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? Boyd (2002) predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications are now available. The rock size reduction process from the mine to the selected milling process facility has not changed since man first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized in four stages: • Stage 1: Mining (rock breakage and fragmentation) • Stage 2: Pre-screening (scalping) • Stage 3: Primary crushing • Stage 4: Fine crushing (secondary, tertiary and quaternary) Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once the project design criteria and the mine plan have been established, the circuit’s utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments are the key stakeholders in the selection of the final comminution circuit, and both departments should be familiar with and contribute to the design of the circuit. This paper focuses on the four stages of a rock size reduction circuit from the mine to the mill, equipment selection, various ore and waste handling flowsheets, and improvements in crusher station design, all with the purpose of maximizing availability and plant utilization percentages. What is a large tonnage? From 1907 to 1914, the American Panama Canal excavated 300 million tonnes of material in 7 years (History of the Panama Canal, Wikipedia). Today’s large mining operations can move the same material in 10 months, using large crushers or multiple crushers for ore processing and large crushers and a mixture of truck haulage and conveyors for handling the large waste tonnages. Some examples include:"

Jan 1, 2017

By Maria S. Adusmilli, Bhaskara A. Rao, Jorge G. C. Barros, Augusto F. Mendonca

Lateritic gold has been the object of study only for a very few years, though nuggets have been mentioned in earlier works even as early as 1984 by Hartt in Brazil. In Mato Grosso State, lateritisation is intense, as is common in all tropical forest areas of the world. Exploration has revealed the presence of recoverable "nugget gold" of variable sizes (30 - 200 gms) but frequently of good size (0 - 40 gms), especially near Cuiaba and Alta Floresta regions. In both of them the host system is a lateritised breccia indicative of a fault or shear zone breccia, though in different lithological domains. The Cuiaba occurrences are phyllitic and show a profile as follows, from top to bottom: 1) Compact ferralite crust. 2) Oolitic to pisolitic compact crust (+ some gold). 3) Mottled concretionary laterite crust. 4) Lateritised "eluvial material" (gold nuggets). 5) Mottled patchy to banded laterite. 6) Banded lateritised phyllite with lenticular to banded goethite. 7) Altered red goethitic phyllite, with quartz veins (+ fine gold). 8) Unaltered grey phyllite with quartz veins (Protore). The Alta Floresta-Juruena River occurrences are volcano-sedimentary and show a profile as follows: 1) Deep brown siltitic, argillaceous and arenaceous material with organic matter (+ gold). 2) Modular and concretionary laterite, compact and indurated, with arsenophyrite in quartz fragments (gold nuggets). 3) Band with silty-clayey matrix and arenaceous in nature. 4) Bedrock meta-arcosian arenite. 5) Volcano-sedimentary with rhyodacites and andesitic basalts, with intercalations of arkosic and greywacke nature. Breccias and quartz veins, and granites associated in different portions (Protore).

Jan 1, 1988

By Michael Li

Unsaturated flow and solute transport were studied in three large columns measuring 1.5 m diameter x 2 m height, loaded with up to 3.7 t of oxidised waste rock, which was excavated from the Stratmat pile at Heath Steele Division, Noranda Inc. and contained elevated concentrations of zinc in the pore water. The bottom of each column was partitioned into 37 squares, each of which was drained independently. Following rain simulations at the top of the rock bed, the drainage in each drain port was monitored for volume and physicochemical parameters at pre-determined intervals. This paper describes some of the observations resulting from the experiments. The main conclusion of the study is that unsaturated flows in waste rock are heterogeneous, and flow channelling is ubiquitous. The results imply that the transport of solutes from oxidised waste rock to its toe drainage is subject to various controlling mechanisms, including geochemical equilibrium control and successive pore water dilution control.

Jan 1, 2000

By T. Negeri, A. O. Orumwense

Microwave pretreatment is one of the emerging technologies which have been reported as having potential economic benefits for the processing of amenable ores. The application of microwave pretreatment to the processing of refractory and finely disseminated ores is of great interest as the technology can potentially reduce high comminution costs and improve mineral liberation. Sized ore samples were subjected to microwave irradiation at power levels varying from 1 to 5 kW over exposure times of between 1 and 6minutes in order to determine the influence of heating rate on mineral transformation, ground product size distribution and mineral liberation. The microwave irradiated samples were ground and subsequently floated. A comparison is made with non-microwave treated samples. Flotation grade and recovery show a strong dependence on the microwave absorption characteristics of the mineral components of the ore, in the following decreasing order -sphalerite, galena, and lastly chalcopyrite.

Jan 1, 2003

By R. L. Grayson, S. S. Peng

Sampling of respirable dust and analyses of samples have been partially completed for a longwall panel. Physical and compositional properties which have been characterized include: 1. Respirable mass concentration, 2. Mineral composition, 3. Particle size distribution by mineral, 4. Particle shape distribution by mineral, 5. Particle angularity distribution by mineral, and 6. Respirable size distribution. Analytical techniques used in the characterization of samples are described, and results are reported with emphasis placed on relationships between the various characteristics and worker locations. Details of existing mining conditions, equipment arrangements, dust control methods and operating system parameters are presented.

Jan 1, 1986