Search Documents

By G. Buchan

This paper discusses the design of long panels for longwall mining at Twentymile Coal Company (TCC) from conception to implementation. The case study of the long panels at Twentymile includes extensive mine plan reengineering in the early 1990's to world record production months in 1996 and 1997. The obstacles of subsidence engineering, environmental regulations, conveyance, ventilation, equipment design, and continuous miner (CM) development timing had to be overcome to successfully begin longwall production within a 4 year time frame. The background and some detail for each of these areas listed will be discussed to show how the coordination of many facets must be pulled together to implement a successful long panel mine plan.

Jan 1, 1998

By P. Asadollahi, M. Invernizzi

"This paper describes the innovative full-face conventional tunnel excavation technology, with its advantages in terms of savings and safety. The full-face approach has been developed throughout the experiences gained in tunnel construction. The innovative design approach is focused primarily on the deformation response of the ground acting first and foremost ahead of the face, which is analyzed, predicted and controlled by pre-confinement of the core. The advantage of this method is particularly evident in difficult grounds. This paper will present the outstanding benefits given by the adoption of the full-face approach in two projects, the “Sochi” and the “Visnove” tunnels. THEORY AND DESIGN ASPECTS OF THE FULL-FACE EXCAVATION The main challenges in tunnel and underground construction industry are gathering the design data from the ground that is being excavated and foreseeing the critical stage during construction, where the materials are in its most critical configuration. These challenges shall be addressed during excavation when the lining and the excavation disturbance have not yet reach the equilibrium. The in situ stresses in the ground are redistributed (forming an “arch-effect”) around the opening, with zones of increased stresses around the walls of the excavation (Figure 1). The distribution of the stresses can be close or far from the excavation profile, depending upon having a ground capable of withstanding the deviated stresses well or unable to withstand them, respectively. In the latter case, the ground will plasticize and deform in proportion to the volume of ground involved in the plasticization phenomenon. When the ground completely cannot withstand the stresses redistribution, it will cause the collapse of the excavation. While in the first case, the arch effect occurs naturally, in the second case, it does occur naturally only when the ground is stabilized properly. In the case of collapse, the arch-effect must be produced artificially operating on the ground prior excavation. The design should be based on the understanding of if and how the arch-effect can be mobilized during tunnel excavation and ensure that is formed by calibrating excavation and stabilization operations appropriately. The arch-effect is function of the medium that is being excavated, the action taken to excavate and the reaction expected following the excavation."

Jan 1, 2018

By B. A. Hancock

New permit discharge standards instituted at Hecla Limited?s Lucky Friday Mine required installation of water treatment plants to manage water quality at two outfalls to the South Fork of the Coeur d?Alene River. The 002 Outfall Water Treatment Plant (WTP) is a clarification-filtration plant for treating the combined mill and underground discharge water flows. Process optimization efforts were a significant challenge until the negative impact the exploration diamond drilling products had on the clarification process was identified and resolved. The products were being wasted directly to the mine water discharge system which was pumped to the surface WTP. Anionic soluble oil and polyacrylamide based products were causing TSS particle hydrophobicity and dispersion that greatly affected coagulation and flocculation response, resulting in excessive chemical usage and treatment control issues. This paper details how problems associated with the drill products negatively impacted the 002 WTP and how system changes, alternative product usage and treatment at the source resulted in more consistent plant performance.

Jan 1, 2011

By W. C. Meyer

Surface tension and its control are important in the concentration of ores by froth flotation, both in terms of producing the proper bubble size distribution and to render the ore surface of interest hydrophobic such that adhesion to a bubble will take place. The influence a substance has on surface tension has traditionally been measured using static, equilibrium techniques. Yet many applications such as flotation involve rate-related effects of surface tension where equilibrium values are not reached. In the time frame of 1 - 300 seconds, aging effects have been noted for bubbles formed in dodecylamine acetate solutions; a slow decrease in surface tension occurs until an equilibrium value is reached, as studied by Finch and Smith (1972). Since stationary bubbles do not exist in flotation cells because of the turbulence generated by agitation and aeration, it is more likely that the chemical composition of the bubble is determined during its formation, under dynamic conditions. The chemical composition is extremely important because the induction time required for a particle-bubble entity to collide and adhere to each other is augmented by favorable surface tension (wetting) proper- ties between the surface of the particle and the bubble air-water interface or envelope, as considered by Mackenzie and Matheson (1963). Finch and Lyman (1976) have established that the probability of a "permanent" attachment taking place during this contact time is aided by the ability of an oil droplet (viz. bubble) to relieve non- equilibrium surface tension effects which are involved in the water-thinning process. This Maragoni effect, or surface elasticity, can be considered in the context of particle agglomeration addressed by Kao and coworkers (1975). Water drainage leads to the formation of a collector-frother meniscus appearing between the colliding entities, arising from their combined partial immiscibility in the water phase and promoted by hydrophobic bonding within the interface. Together they constitute a liquid bridge whose force of attraction drawing the particles together is proportional to the interfacial tension existing between the water phase and liquid bridge. This adhesive force shows an approximate linear decrease with separation distance until rupture occurs, that is, FX = Fmax (1 ? X/Xr) (1) for a distance of separation X and rupture distance G. The greater the surface elasticity of the bubble, the greater will be the rupture distance and the better will be the force of adhesion. Since van den Tempel (1965) has related surface dilational properties of bubbles to the elasticity, E, of the film as

Jan 1, 1983

By Laurent Rus, Bakar Amara, Jean Habimana

The La Fontaine Tunnel in Montreal, Quebec is currently undergoing major structural rehabilitation work and systems upgrade work to comply with current codes, standards and best practices in fire life safety and to extend its lifespan of this 55-year-old immersed tube tunnel for at least another 40 years. The paper discusses design consideration of ongoing works that include structural analyses to evaluate repair strategies for the post-tensioned reinforced caissons, the scheme to repair two leaky joints between caissons, the design of passive fire protection that involved in situ and real scale laboratory tests, and other tunnel systems upgrades.

Jun 13, 2023

By W. J. Douglas

The mine manager in today's environment is faced with a wide variety of problems and challenges which must be addressed if efficient and profitable operations are to be achieved. Expansion of operations has, in many instances, resulted in inexperienced work crews, face supervisors, and superintendents. The complexities of a mining system preclude rapid movement through the learning curve for moat personnel. The management of production suffers both from this inexperience and the lack of standard procedures and methods for planning, schedul ing and analyzing production systems. The lack of visibility of information, as well as of the operations themselves, due to their remoteness, adds to the problem of production management.

Jan 1, 1980

By Martin H. Stanczyk

The Organic Act of 1910 established the Bureau of Mines and gave it authority and responsibility for conducting research on separation, recovery, and recycling of waste products and scrap generated by the mineral and metals industries and the consuming public.(1)1 It was apparent to our Nation's leaders even then that mineral resources, once mined, are irreplaceable and that the development of methods for recycling the values contained in wastes would be required to solve the problem of even¬tual scarcity, Estimates of the increase in per capita consumption of mineral resources in this country indicate that the consumption of metals, minerals, and fossil fuels by 1980 will be double that consumed in 1970 (2). The United States can expect to meet its future mineral needs in three basic ways: the first is through increased production of primary raw minerals; second by increasing imports from foreign sources; and third by recycling secondary materials and metals that were formerly discarded as waste. Rather than consider these

Jan 1, 1972

By Ingemar Marklund

INTRODUCTION Today at LKAB, the primary mining method used is sublevel caving, independent of ore-body size, shape, dip, and geographical location. The mining of small ore bodies with relatively flat dip involves a lot of develop¬ment work, a large initial investment, big dilution, and large ore losses. In 1975 serious investigations into other possible methods, especially for those small ore bodies which do not lie in direct contact with other ore bodies, began. Different methods were studied and a number of in¬teresting ideas came from Russian mines. An analysis was made of one of the proposed methods, sublevel benching, in which mining is carried out from raises, and which uses the throw from the blast to place the broken ore. However, there were reservations about working in big open rooms at great depth, and doubts about the possibility of getting acceptable drilling results in an acceptable environment from raised platforms. Testing was therefore delayed for a time. However the investigations continued and in the fall of 1976, it was decided to try vein mining in a small ore body (Indian) (see Figs. 1 and 2). MINING RESULTS The results are now available from the mining of Indian and are as follows: Ore plan area 1200 m2 Level height 50 m Ore volume 60 000 m3 Ore tonnage 270 000 t Iron content 62% Dip 0.69 rad (40°) Ore thickness 14 m Ore compressive strength 26 MPa Ore C-factor (fracture density) 0.21 Hanging wall compressive strength 28 MPa Hanging wall C-factor 0.27 About 40 000 m of the holes were drilled by ring drills with an average productivity of 85 m/shift; loading of a round (2 rows, 750 m of hole) was usually accomplished in one shift. The total ore recovery was about 270 000 t with an average iron content of 59%, and three to four shifts were required per round (4700 t) to load. The principal of "throwing" the rock during blast¬ing worked well, and no ore remains on the footwall. ROCK CONTROL Before mining commenced at Indian, it was dis¬covered that the rock strength in its vicinity was rela¬tively poor. Since the ore is flatly dipping, and mining was to take place with open rooms, the strength of the hanging wall was of great importance. A supplementary program of exploration drilling was done during the fall of 1976 in order to assess fracture spacing and rock strength from the drill cores. Results showed that the strength of the hanging wall was low because of the many fractures. A decision was made to try cable bolting of the hanging wall by extending some of the ordinary blast¬holes. Cables (20 mm diam) were grouted in these larger holes and the rest of the hole was then utilized for ordinary loading (see Fig. 2). About 100 bolts altogether were installed and, to date, only small falls have occurred and the hanging wall is holding. Its exposed area is 2100 m2 DEVELOPMENT WORK On the 350-m level, four crosscuts (two per mining room), one longitudinal drift, and two elongated drifts (one per raise) for the raise climber were developed as shown in Fig. 1. Of the 230 m of drift, 60 m were in ore and the rest in waste. For mining room A alone, a total of 115 m of drift were needed with 30 m in ore. The drift dimensions were about 4.5 X 5.5 m. In the drifting on the 300-m level, two connecting drifts were driven from one existing transport drift forward to the respective raises. The total development was 93 m, all in waste (Fig. 1). The two raises having a length of 80 m each were driven at an angle of 0.68 rad (39°) from the hori¬zontal. They were driven along the footwall contact with a separation of 30 m and had an area of 10 m2. LONG-HOLE DRILLING The drilling of long holes with the ring drilling unit began in the fall of 1977 in raise A. The equipment consisted of an Alimak raise climber, equipped with a lower platform from which the charging was done.

Jan 1, 1982

By A. Datta

An appropriate scale-up methodology is very useful for ball mill design and optimization of the grinding circuit. To date, the scale-up is based on the selection and breakage function model using lab mill data. However, a major drawback of that approach is that the charge motion in a lab mill is vastly different from that in a large industrial mill. Therefore, in the methodology proposed here, first the energy of individual collision in the mill is computed employing the discrete element method (DEM). Then the breakage of particles as a function of collision energy is studied in a separate experiment. Together, this information constitutes what is known as collision energy based population balance model. The appropriateness of this model is shown for different batch grinding mills.

Jan 1, 1999

By Rafael Moure

On April 21, 1980 the Oil, Chemical and Atomic Workers Union (OCAW) submitted a petition urging the revision of the Mine Safety and Health Administration (MSHA) permissible exposure limit to radon daughters in underground mines. This petition asks for: 1. Annual worker exposure to be lowered from the current 4 WLM/year to 0.7 WLM/year; 2. Full economic protection for workers whose exposure exceeds the proposed 0.7 WLM/ year; and 3. The primary means of lowering workers' radiation exposures shall be environmental controls. I will present the scientific rationale for the lower standard requested in our petition to the Department of Labor. [1. Radiation Exposures to Uranium Miners] Two types of radiation exposures are present in the environment of uranium mines: A. [External Exposure] to gamma sources which until 1978 was considered as negligible compared with internal alpha radiation. R. E. Utting (1), in an investigation of three Canadian uranium mines, found levels of exposures adding to an annual dose equivalent of 3 rems (30 mSv)/year. He concluded that gamma dosages may be a major fraction of the maximum permissible dose for many individual miners. The U.S. experience has shown that there is significant gamma exposure in U.S. uranium mines and, therefore, it could contribute to the total radiation exposure to the lungs in combination with internal alpha radiation. Before ventilation improvements in uranium mines, the contribution of external radiation to total lung dosage was relatively small. After improvements in ventilation, the reduction in internal radiation exposure appears to be in 1980 as low as 1/10 of the 1950 dosages. However, ventilation improvements do not affect external gamma radiation. Gamma radiation remains at the same 1950's level, and it represents today a higher proportion of the total radiation burden to the miner's lungs. MSHA regulations (57.5-47) state that if gamma exposure is below 2.0 milliroentgens per hour, then workers are not required to wear gamma dosimeters and cummulative gamma radiation records need not be kept. Assuming an exposure of 1.9 milliroentgens per hour per 173 hours/month for 12 months,a miner would accumulate a dose from external radiation of 3.9 rems/ year. This dosage would, of course, go unrecorded. MSHA, therefore, should consider a downward revision of the external radiation permissible exposure limit of 2.0 milliroentgens/hour. MSHA should make clear that this exposure level, when added to the internal exposure, does not make for sound health physics -even though the measured current levels do not approach 2.0 milliroentgens/hour. B. [Internal Exposure] to alpha radiation is still the larger contributor to lung irradiation in uranium miners. The target organ is still the lung. The parameters to be considered in determining the biological radiation load appear in Table I for radon daughters present in the upper respiratory tract (URT). TABLE I RADIATION DOSE PARAMETERS IN THE URT OF URANIUM MINERS Parameter Uranium Underground Mining [1. Quantity of the Absorbed Radon daughters (Po-218, Nuclide Pb-214, Bi-214) deposit in bronchial and lung tissue. (Measured by air concentration, Working Levels) 2. Type of Radiation Emitted Alpha Particles 3. Energy of Radiation High-Linear Energy Transfer 4. Half-life of the Nuclide Ra 222, 3.8 days in the Organ Po-218 (RaA), T1/2 = 3.1 minutes Pb-214 (RaB), T1/2 = 26.8 minutes Bi-264 (RaC), Vi = 19.7 minutes 5. Selection Factor of the Direct inhalation with mine Organ dust to be deposited in the tipper Respiratory Tract 6. Mass and Form of the Organ Especially cancer sensitive, tracheobronchial region and bronchi* 7. Distribution of the Activity Dependent on deposited dust in the Organ distribution in the Upper Respiratory Tract 8. Chemical Nature of All compounds (RaA, RaB, RaC) Incorporated Substance biologically insoluble. (Only localized, irradiation) *See Reference (2)] The parameters of Table I depend, in turn, on the demography of the exposed population, especially: 1. Age 2. Sex 3. Health Status 4. Genetic Constitution 5. Lifestyle (Smoking, Diet) Some of these demographic characteristics of uran-

Jan 1, 1981

By C. D. Wittreich

The University of Idaho, Department of Metallurgical and Mining Engineering, through the Generic Mineral Technology Center, has been engaged in mine design research at the Lucky Friday Mine, Mullan, Idaho. The purpose of the research is to develop and implement the longwall underhand cut-and-fill mining method for conditions at the Mine. The longwall underhand cut-and-fill mining method involves backfilling mined stopes with a compacted tailings-cement mix. After the backfill has been allowed to cure, mining is resumed from underneath. Horizontal stresses in the Lucky Friday Mine are exceptionally high and rock bursts are a common problem. Beus and Chan (1980) have reported a 2:1 horizontal to vertical stress ratio at the mine with a 65-MPa (9,500-psi) maximum horizontal stress at the 1,295-m (4,250-ft) level. Using this mining method under these stress conditions, it is desirable to have a backfill material that has sufficient strength to safely carry the high horizontal wall loads while minimizing external steel supports.

Jan 1, 1987

By Thomas R. Kuesel, Harvey W. Parker

INTRODUCTION This paper describes the use of a shield and compressed air for construction of a short section of a pair of twin single-track tunnels for the Metropolitan Atlanta Rapid Transit Authority (MARTA) transit system. Although only two blocks long, this section posed the greatest difficulties to both engineers and contractors, and is the most expensive section of line construction on the MARTA system. All this derives directly from its setting--these tunnels had to be constructed through mixed-face conditions. SETTING The Broad Street tunnels form a link between the Peachtree Center and Five Points Stations, in the heart of Atlanta's central business district (Figure 1). Peachtree Center sits atop a solid rock ridge, which inspired the design of a deep rock-mined station, as described in the 1979 RETC. Five Points Station is MARTA's hub--the intersection of the system's two main branches. It is located in the old railroad gulch, a filled-in erosional valley at the base of Peachtree Ridge, and was constructed by open-cut methods. The alignment and profile of the Broad Street tunnels were closely constrained by these two adjacent anchors, and in the six-block stretch between them there was very little room for maneuvering. Since the rock ridge petered out about in the middle of the section, it was evident at the outset that there would be about two blocks of rock tunneling at the north end, two blocks of soft ground construction at the south, and two blocks of mixed-face in between. It is this central two-block section that is the focus of this paper.

Jan 1, 1981

By Y. B. He

The effect of the stability and rheological properties of magnetite dense medium on the separation performance of a 6" dense medium cyclone (DMC) is studied with the use of fine density tracers. The tests in which different size fractions of magnetite are used to prepare the dense media reveal that at low medium densities (<1.5 s.g.), the best separation is achieved when using the magnetite with intermediate particle sizes (du3.2=18 11m). At medium densities above 1.5 s.g., however, it is beneficial to use coarser magnetite. With the fine magnetite dense medium, an increase in medium density results in a decrease in separation efficiency. With the coarse magnetite, an opposite trend is observed; the separation efficiency is improved with increasing medium density. An accurate cutpoint control is critical in gravity separation. The cutpoint shift for coarse feed particles is found to decrease with increasing medium stability (density). It assumes values close to zero in a highly stable fine dense medium. When the size of the treated particles is small (<0.5 mm), the cutpoint shift is mainly determined by medium rheology. With increasing medium density, a continuous increase in cutpoint shift is observed.

Jan 1, 1993

By P. H. S. W. Kulatilake, T. Hudaverdi, C. Kuzu

Prediction of blast fragmentation plays a key role for overall productivity of mines. In this study, a new multivariate analysis procedure for prediction of blast fragmentation is presented. Several blasts performed in various mines and rock formations worldwide were brought together and evaluated. An extensive blast database was created. Blast design parameters, the modulus of elasticity and in-situ block size were considered to perform multivariate analysis. A complete multivariate analysis procedure was applied in three steps. First, a hierarchical cluster analysis was used to separate the blast data into different groups of similarity. Two different groups were formed based on the elasticity modulus values. In the second step, group memberships were checked by discriminant analysis. The dominant parameters of the occurrence of the groups were determined. Also, discriminant analysis was used to determine the group membership of the respective blasts. As the last step, the multivariate regression analysis was applied to develop prediction equations for estimation of the mean particle size of muckpiles. Two different prediction equations were developed based on the rock stiffness. Validation of the proposed equations on various mines was performed. Prediction capability of the proposed models was found to be strong. The models are not complex and are suitable for practical use at mines.

Jan 1, 2011

By Stefano Ceccotto, Eugenio Trussoni

"INTRODUCTION Contemporary city is made of layers. Physical structures layers (built fabric, residential, commercial industrial etc. ), infrastructural layers (below and above ground), “green” layers (parks and open spaces), and also informational layers, i.e. connections, links, between sectors of the city and other territories. The “city of layers” concept represents the exercise of “rebuilding the city” per each layer, highlighting those physical built structures that are functional to define a relation. For example, if consider the “connection” relation, the city is re-designed by considering only transportation built structures. The layer obtained in such fashion is hence the “transportation” layer, including below grade infrastructures (subways) and above grade lines (rail, bus, tramways etc.), as below shown in Figure 1.In this sense, the contemporary city is represented by separate constructs assembled together according to a specific functionality (e.g. “connection”). As a consequence, the relation between what is built underground, and the related above-ground development, can be perceived in his most evident appearance. What could happen within the contemporary city if the planning process would begin from below to above and not vice-versa?INTERACTION The question risen in the introduction is strategic when approaching the difficult task of designing (or re-designing) a multi-level organism like the contemporary city. Nowadays, the theme of integration between underground and at-grade master planning has become the subject of many urban renovation projects, where the design process has begun within the transportation layer, underground, and further developed by interacting with at-grade structures already existing or in phase of design.A series of case studies where below/above interaction plays a key role in the project will be further analyzed. Moreover, it is relevant to understand the mechanics of an urban transformation process that originates within the transportation layer and ends up with the design of entire sectors of the city. The Transit Oriented Development approach is a useful tool to clearly understand such transformation process. TOD has become, in particular in the last decade, one of the most effective tools for urban design, in order to solve simultaneously the many different instances related to transit planning, urban design and real estate market."

Jan 1, 2016

By F. G. Loper

Simulation as a mathematical technique is not new. However, recent increases in digital computer speeds and the ease of programming with languages such as Fortran have centered a good deal of attention around simulation in the last few years, Many sophistications of the method have been developed during this time. However, the ability to simulate mathematically still hinges on the ability to ignore unimportant details which would complicate the mathematics and make simulation impractical, Thus, with this attitude in mind, it becomes very easy to design a pseudo- simulator which will predict average conditions very well, but can not truly allow a detailed study of the system being simulated. Most simulations fall into this category, along with the case mentioned here. This paper is not intended to be a critical treatise of the simulator used to study a particular mining system. Instead, it will be used to illustrate the aspects of simulator development. The steps in the development of any simulator are described, along with same detail of the phosphate mine simulator itself.

Jan 1, 1966

By Timothy J. Matthews, Ted Klemetti, Timothy J. Batchler, Daniel J. McElhinney

Unplanned tailgate collapses and difficult mining conditions in U.S. longwalls have necessitated the use of innovative tailgate support systems. Severe ground movement induced by longwall loading has caused operators to utilize secondary support systems that can match yield and strength requirements with expected ground reactions. Standing support performance requirements depend on the nature of the ground deformation behavior, and therefore require a good understanding of the interaction between the support and ground to achieve an optimum roof support system. Mining operations often employ standing support strategies that are unique to their mine. A support system that functions successfully in one situation could fail in another situation. It is important that the design and installation of the standing support systems provide the highest probability of preventing roof falls. Pumpable roof supports are currently being used to provide a safe working environment for longwall mining. A full understanding of the impact of these performance characteristics is necessary to optimize the support application and to provide a foundation for making further improvements in the support performance. Optimization of roof support applications helps to ensure the protection of mine workers by preventing roof falls due to inadequate support design. The load capacity and stiffness characteristics of a 27-in.-diameter pumpable support system was evaluated using the National Institute of Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS). Previously, tests to evaluate the performance characteristics were performed on a single pumpable support. The goal of this new research is to evaluate the performance characteristic effects of the pumpable support system and compare it to an individual pumpable test examination. This research of a pumpable support system configuration simulates the current installation practices in U.S. coal mines.

Jul 1, 2023

By S. Lee, F. Campero

"Past heap leach design has evaluated hydrodynamic parameters based on a uniform particle size of heap material, but has ignored the equal importance of the instability of fine migration within heap stack in the beginning stages of the irrigation process. The proposed probabilistic model evaluates internal fine erosion and segregation potential of well-graded crushed ores by considering the entire particle size distribution shape and site compaction degree. Using this model, unsaturated flow model parameters were successfully evaluated based on synthesized soil-water characteristic curve (SWCC). Additionally, one-dimensional unsaturated transient flow modeling with Hydrus 1D® showed that the different recovery efficiencies of heap material under unsaturated flow patterns depending on the particle size distribution and compaction degree of heap material. Agglomeration preprocess employed by most heap leach sites can reduce the potential of fine erosion within heap material significantly, but internal stability of crushed ores and hydrodynamic-based analysis of heap material’s pore structure is equally important in the prescreening stage in order to improve efficiency of the heap leach and avoid a costly agglomeration process. INTRODUCTION Accurate estimation of heap leach recovery is a difficult task due to the variety of design parameters that need to be considered - such as geochemistry, hydro-dynamics, and geotechnical design aspects, most notably particle size distribution through the process of agglomeration. After agglomeration techniques were introduced to heap leach design, the influence of particle size distribution and compaction degree in enhanced heap leach recovery has been neglected. The main purpose of agglomeration is to prevent fine segregation and internal erosion during and after heap stacking for well graded crushed ores, which will eventually diminish heap reach recovery. Recent studies show that agglomerated heap materials that had been consolidated at 10 meters below heap surface can release the fines after contact time with lixiviant to the compacted heap material and produce poor drainage performance (Milczarek et al, 2013). It must be noted that engineers and practitioners should investigate feasibility of agglomeration benefit prior to heap leach design because the agglomeration process can incur up to 20 or 30% of project costs. Internal stability of stacked heap material is mainly governed by the particle size distribution of crushed ores. Depending on this stability, segregation and internal erosion of fines can be mitigated by the application of moderate compaction effort during heap construction. Investigation of segregation and internal erosion potential therefore takes precedence for well graded crushed ore since reaction time and contact area with lixivant are greater in finer ores."

Jan 1, 2016

By Michael Moats, Weston Hartzell

The stable domestic supply of gallium, indium, and germanium has been identified as a critical need for the USA. Electric arc furnace dusts processed to recover zinc produce a process residue that could be a potential source of these critical materials. An industrial zinc leach residue was characterized to determine the predominant mineral phases and leached with common mineral acids. Atmospheric agitated leaching using sulfuric acid and hydrochloric acid were examined to determine the extractions of gallium, indium, and germanium as a function of concentration, temperature, and time. Extractions of gallium were found to be similar to iron in all experiments. The maximum percentage of Ga, Ge, and In leached into solution were 82%, ~100%, and 89%, respectively.

Aug 8, 2023

By B. Samanta, S. Bandopadhyay

Ore grade modeling of a placer gold deposit is considered a challenging problem even today. Typically, gold-bearing deposits show extremely erratic and unpredictable grade variation. This is principally because of isolated occurrences of gold metal within a few high-grade pockets. Because of sporadic fluctuation of high-gold-grade distribution, the overall spatial continuity of the deposit becomes poor. This type of variation is often described by a lognormal or highly skewed frequency distribution, and the spatial continuity of the deposit is characteristically represented by a variogram model that exhibits a high nugget component. Further complicating the matter is the sparse availability of drillholes to capture such erratic variation. Due to the prohibitive cost of drilling, gold grade and reserve estimations are typically carried out using insufficient exploratory data. Use of a traditional estimation technique on limited data often produces an unreliable ore grade model. Kriging and its nonlinear variation, lognormal kriging, are frequently used in gold deposit modeling (Rendu, 1979; Journel, 1980); however, kriging is flawed by the smoothing effect. Moreover, though kriging is known to be globally unbiased, it is not free from conditional bias. As a result, if a deposit is modeled using the traditional kriging technique, a high-grade zone can be predicted to be a low-grade zone and vice versa. Predicting high grade as low grade results in a missed opportunity to exploit profitable ore. On the other hand, prediction of low-grade ore as high-grade ore might result in financial loss for a mining operation. Thus, the use of kriging for ore grade mapping of a gold deposit may not be recommended. Estimation techniques (including kriging) can produce an estimate with minimum error in a minimum-error variance sense. However, no matter which estimation technique is used for grade modeling of a highly erratic deposit like gold, the error margin is bound to be high. Therefore, any grade prediction made for an unknown location is associated with high uncertainty. Since various mine-planning operations, including derivation of grade tonnage curve, pit design and economic analysis of the deposit, are based on estimated grade rather than true grade, a mining project evaluation that depends upon estimation will be subject to considerable risk. Thus, the successful design of a mining project not only depends upon accurate grade estimates, but also upon accurate assessment of uncertainty, for predictive grade is equally important. Although the kriging standard deviation is used as an indicator of uncertainty for prediction, it is flawed by characteristics related to a data-independence property. This study, therefore, investigates the stochastic simulation technique of conditional simulation for ore grade modeling of a placer gold deposit at Nome, Alaska. It is expected that the research will provide a better solution to ore-grade deposit modeling than the kriging technique because (1) conditional simulation preserves spatial continuity as well as reproduces the data histogram, thus avoiding the smoothing problem; and (2) generation of multiple realizations helps to accurately quantify the uncertainty about grade values in the deposit.

Jan 1, 2009