Search Documents

By T. Braun

A greenfield open pit gold mine in Latin America suspended operations less than three years into an eight-year mine plan after a waste rock dump and heap leach facility sustained substantial damage from a deep-seated landslide. No injuries to employees were recorded because of the slow-moving failure. Due to early detection by the operations team, the owner had sufficient notice of the potential failure and successfully rinsed the heap leach facility prior to the failure event. Engineers estimated approximately 35 million cubic meters of mass movement below the waste rock and heap leach facilities. The original eight-year mine plan produced approximately 60,000 ounces of gold per year. After the failure, the owner terminated gold production, re-configured the mine site to a safe, standby condition and launched a detailed investigation into the root-cause of the failure. Approximately two years after the shutdown, legal interests filed a statement of claim and named three engineering design firms and individuals involved in the project. Several years of litigation, including discovery and deposition proceedings, followed as the legal process considered evidence spanning a 20-year timeline. Changes in project ownership and consulting firms during the development and operations phase complicated the process. In 2017, the plaintiff and last defendant settled. The author was involved as the corporate representative for one of the engineering design firms.

Mar 2, 2022

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2009 draws upon information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on industry exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analyses of exploration activities by the mineral industry based upon these data. Two types of information are reported and analyzed in this annual review of international exploration for the year 2009: 1) budgetary statistics expressed in U.S. nominal dollars provided by Metals Economics Group (MEG) of Halifax, Nova Scotia, and 2) information on regional and site-specific exploration activities that took place in 2009 and were compiled by the USGS. The MEG information summarizes planned company budgets for worldwide exploration activities in 2009, primarily for base metals (copper, lead, nickel and zinc), diamond and precious metals (gold, platinum-group metals and silver). Information on uranium exploration was included in the MEG overview for the first time in 2007, although this information was not included in the USGS analysis prior to 2008. The MEG survey methodology was changed in 1999 to include companies with exploration budgets greater than $100,000, as well as those companies included in prior studies whose anticipated budgets were above $2.9 million. MEG estimates that its post-1999 surveys cover at least 90 percent of world nonferrous nonfuel mineral exploration budgets. The 2009 survey is reported by MEG to cover an estimated 95 percent. Companies who chose not to participate in the MEG study, private companies that do not publish data and government-funded exploration activities make up the majority of the remaining 5 percent. MEG included 86 more companies in its 2009 survey than it did in 2008.

May 1, 2010

By LUKAS FAHLE, Andrew J. Petruska, JURGEN F. BRUNE, Gabriel Walton, Elizabeth A. Holley

Adverse ground behavior events, such as convergence and ground falls, pose critical risks to underground mine safety and productivity. Today, monitoring of such failures is primarily conducted using legacy techniques with low spatial and temporal resolution while exposing workers to hazardous environments. This study assesses the potential of novel simultaneous localization and mapping (SLAM)-based light detection and ranging (Lidar) data quality for rapid, digital, and eventually autonomous mine-wide underground geotechnical monitoring. We derive a comprehensive suite of quality metrics based on tests in two underground mines for two state-of-the-art mobile laser scanning (MLS) systems. Our results provide evidence that SLAM-based MLS provides data of the quality required to detect geotechnically relevant changes while being significantly more efficient for large mine layouts when compared to traditional static systems. Additionally, we show that SLAM-specific processing can achieve an order of magnitude better relative accuracy relevant for change detection than quality metrics derived from traditionally deployed tests would suggest while reducing SLAM drift error by up to 90%. In collaboration with an operating block cave mine, we confirm these capabilities in field tests on a mine-wide scale and, for the first time, demonstrate methods of rockfall detection using MLS data. While more work is required to investigate optimal collection, processing, and utilization of MLS data, we demonstrate its potential to become an effective and widely applicable data source for rapid, accurate, and comprehensive geotechnical inspections.

Aug 16, 2022

By J. K. Wilmshurst

Absorption, emission and reflection techniques for the study of [molten] inorganic materials at high temperatures have been critically examined. In general, the reflection technique is the most satisfactory for tine study of pure materials, while the absorption, and possibly also the emission techniques, may be useful for studies of certain dilute solutions. In the present investigation infrared emission spectra for sodium nitrate and silver chloride were obtained together with absorption spectra derived from reflectivity data by the method of Robinson and Price for sodium nitrate, silver chloride, lithium and potassium fluoride and their 1:2, 1:1 and 2:1 mixtures and for solutions of zirconium tetrafluoride in lithium-potassium fluoride (1:1) and sodium-potassium fluoride (1:1). It is concluded that vibrational spectroscopy cannot give unambiguous information concerning the existence of complex ions in fused salt, mixtures.

Jan 1, 1963

By Robert A. Clifton

It seems probable that more and more minerals will be used in plastics as time goes on. This must occur because the minerals will; aid in processability, enhance the engineering properties, reduce the cost, and above all conserve large amounts of petroleum based chemicals. This paper examines the advantages and disadvantages of using the minerals and the ability of the domestic minerals industry to support this possibly very large undertaking. In the author's opinion, it can. This talk is excerpted from a forthcoming Bureau of Mines Information Circular.

Jan 1, 1985

By T. C. Vogt

Earlier we described the uranium mineralogy of an areally broad sampling of Crownpoint ore, including the characterization of organic carbonaceous material associated with the uranium mineral. (1) We also reported on the leaching behavior of Crownpoint ores with a mild alkaline leaching system, oxygen (02)-sodium bicarbonate (NaHC03). (2) There was a wide range of leaching responses, with samples from some areas leaching at a slow rate with low uranium recovery. Evidence indicates that in these samples the organic material is intimately associated with the uranium mineral and shields it to some extent from contact by the leachate. (1,2) One method to obtain faster leach rates and higher recoveries is to use a chemically severe leaching system such as sodium hypochlorite (NaOCI) as an oxidant. (3) The use of sulfuric acid (H2SO4) and an oxidant for leaching ore in surface milling operations is widely practiced to effect high recovery of uranium (U308) from the ore. (4,5,6) The U308 is mobilized as the disulfate complex, U02(S04)224-, or possibly, the trisulfate complex, U02(S04)34-, is the soluble species. (7) Sulfuric acid leachate formulations were used in the first in-situ leaching operation in the Shirley Basin in Wyoming. (8) More recently H2S04 formulations have been used in the Rocky Mountain Energy field tests in the Powder River Basin (Bear Creek) and in the Teapot forma¬tion at Nine Mile Lake site near Casper. (9,10) Laboratory studies related to the use of H2SO4 for in-situ leaching have been reported (11-17) and Yan has .reported packed column leach studies on Crownpoint ore using H2504 and oxidant. (18)

Jan 1, 1981

By L. Adler

A systematic, balanced and inclusive formulation of the vast input data for mine design is presented. Since the quality of this statement severely influences subsquent design it is extremely important to senior mining engineers and the profession-at-large. If unfocussed, chaos can result along with serious ommisions. The basic categories, each a traditional one are: 1) Natural Conditions (geology and geography), 2) Company Capabilities (monetary and managerial), 3) Public Domain (regulations, contracts, good will, etc.) and 4) State of Art (mining engineering professionalism). To further reduce the data additional organizing principles were used: the distinctions of mining (vs. civil) engineering, proceeding from the general to particular, the basic engineering dimensions, and separating dependent from independent variables. The results are a unique and unified corpus, which anticipates the mine design procedure.

Jan 1, 1987

By Ralph M. Barnett

It is no longer a question of "If" mining operations will meet standards and regulations set by various governing bodies and the demands of citizen groups. Legislation is fact. The needs of citizens are becoming more of a integral part of mining company planning. "Open Planning", regardless of some frustrations it provides, is working. Climax, AMAX Chemical and AMAX Exploration are successfully employing several citizen involvement techniques in exploration and feasibility study phases of planning for potential new mines.

Jan 1, 1978

By JOHN HOMER, Jacob L. Carr, Jonathan K. Hrica, Kathleen M. Stabryla, Iman Benbourenane, Jennica L. Bellanca

Given the recent focus on powered haulage incidents within the US mining sector, an appraisal of collision avoidance/warning systems (CXSs) through the lens of the available research literature is timely. This paper describes a rapid review that identifies, characterizes, and classifies the research literature to evaluate the maturity of CXS technology through the application of a Technology Readiness Assessment. Systematic search methods were applied to three electronic databases, and relevant articles were identified through the application of inclusion and exclusion criteria. Sixty-four articles from 2000 to 2020 met these criteria and were categorized into seven CXS technology categories. Review and assessment of the articles indicates that much of the literature-based evidence for CXS technology lies within lower levels of maturity (i.e., components and prototypes tested under laboratory conditions and in relevant environments). However, less evidence exists for CXS technology at higher levels of maturity (i.e., complete systems evaluated within operational environments) despite the existence of commercial products in the marketplace. This lack of evidence at higher maturity levels within the scientific literature highlights the need for systematic peer-reviewed research to evaluate the performance of CXS technologies and demonstrate the efficacy of prototypes or commercial products, which could be fostered by more collaboration between academia, research institutions, manufacturers, and mining companies. Additionally, results of the review reveal that most of the literature relevant to CXS technologies is focused on vehicle-to-vehicle interactions. However, this contrasts with haul truck fatal accident statistics that indicate that most haul truck fatal accidents are due to vehicle-to-environment interactions (e.g., traveling through a berm). Lastly, the relatively small amount of literature and segmented nature of the included studies suggests that there is a need for incremental progress or more stepwise research that would facilitate the improvement of CXS technologies over time. This progression over time could be achieved through continued long-term interest and support for CXS technology research.

Jun 17, 2022

By S. K. Bhatt

This paper reviews major developments in continuous haulage technology for underground coal mines. Haulage systems, both in use and development, are investigated through a comprehensive literature search and visits to mines and manufacturers. The systems include flexible conveyor train, mobile conveyor, multiple-unit continuous haulage, extensible, and belt turning systems. Strengths and weaknesses of the systems are assessed in light of their operating under remote control and their application to the computer-assisted continuous mining machine being developed by the U.S. Bureau of mines. Through mining scenarios, candidate haulage systems are conceptualized to be consistent with the capabilities of the mining machine.

Jan 1, 1990

By R. C. Bunge

A magnetogravimetric separation is the consequence of two competing forces with opposing directions, i.e., magnetic buoyancy and gravitation (or centrifugal force). While magnetic buoyancy is a function of particle volume, gravitational force depends on particle mass, thus permitting a separation according to specific gravity. Since magnetic buoyancy is not a phenomenon of common knowledge, this chapter is meant to briefly introduce the theory of magnetogravimetric separations. A particle that is suspended in a magnetic fluid which is exposed to an inhomogeneous magnetic field experiences a repulsive force -the so called magnetic buoyancy. In order to illustrate this effect, an analogy with the more familiar hydrostatic buoyancy is drawn. Hydrostatic buoyancy occurs due to unsymmetrical pressure distribution 'above' and 'below' a suspended particle (fig. 1).

Jan 1, 1990

By Bo Hyun Kim, Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health have tested the finite element code, UT3PC, with LaModel to evaluate their results using know case studies. The purpose of the testing was to demonstrate the usefulness and limitations of these programs in evaluating mine layout design. Both of these software packages are simple to use and free for public download. Their use by mine engineers, along with other tools, such as empirical methods, can enhance the assessment of a mine layout design. LaModel can model mining layout on a mine scale or, at least, on a multiple-panel scale. However, this software has limitations in calibrating to conditions at many coal mines in the western United States. The UT3PC software models smaller parts of a mine and is used to evaluate the design of pillars, shafts, or drifts; but the software calculates all components of the stress tensor and provides stresses, displacements, and safety factors throughout the model volume. The two codes are used to evaluate design of one known case, and UT3PC is used to evaluate another case. The results and approaches demonstrated in the testing are intended to aid mine engineers in evaluating site-specific problems and to show that these tools can provide useful information to the mine engineer in evaluating mine layout design.

Jul 1, 2023

By Ma Fangyuan, Li Min, Xu Bing, Xian Yushuai, Zhao Tonglin

The study explored a new combination amine collector (XK-28) that can obtain better flotation index and defoaming rate for magnetic iron ore. A pure quartz mineral test indicates that dodecylamine, XK-I, or XK-II has good collection effect on quartz and their best flotation pH is in the range of 6–7. The experimental results of a combination collector (XK-I:XK-II = 2:8.) show that the separation effect for quartz and magnetite is better than that of a single collector. The single factor for actual mineral test shows that when the combined reagent is used as the collector, the best conditions are pH = 7, 90 g/t dosage, and XK-I:XK-II = 2:8, which is consistant with the pure mineral test. The difference for dodecylamine as a collector is that the optimal dodecylamine dosage is 60 g/t. Under the best conditions of actual ore test, dodecylamine and XK-28 are respectively used as the collector to compare the flotation indexes. Study results indicate the magnetite grade using XK-28 as the collector is higher by 3.02% than that of using dodecylamine, recovery is increased by 1.92% over that of using dodecylamine. Based on the measurement results of zeta potential, uses of XK-28 can slightly increase the zeta potential difference of quartz and magnetite to enhance the flotation effect. The mechanism of action between the XK-28 collector and the actual ore from the Gongchangling plant is physical adsorption, and this adsorption also has hydrogen bond formation. Contact angle results shows that XK-28 improves the hydrophobicity of quartz better than dodecylamine. Compared with dodecylamine, XK-28 is more sparsely arranged on the surface of the foam. The foam produced by the XK-28 collector has better air permeability and it is more likely to merge and disappear with bubbles.

Jul 21, 2021

By S. A. Diatchkov

There is a misconception that mineral-project economic evaluations in the former Soviet Union are either nonexistent or very limited. This is not the case. In fact, there are at least two basic methods that can be utilized to evaluate the vast mineral resources of the Commonwealth of Independent States (CIS). Evaluation procedures are based either on a comparison to known projects, which may rely on limited available data, or on potential-profit calculations, which generally uses more extensive databases. Significant philosophical differences between these systems and those utilized in the Western world include the following: •Under the centralized-government system, the economic evaluation of a mineral project was based on artificially determined mineral prices and costs. Every ten to 12 years, prices for concentrates and metals were established by the Council of Ministers and remained unchanged until the next reconsideration of prices .

Jan 1, 1995

By S. M. Smouse

Total world energy consumption is projected to continue its strong growth of recent years. Because coal is the most abundant fossil fuel, it will likely remain an important energy source, particularly for power generation, into at least the early years of the next millennium. Clean coal technologies are available today that can economically reduce air pollution, primarily SO2 NOx and particulates, and for the higher efficiency technologies, CO2, from power generation. U.S. Department of Energy analyses show that the adoption of clean coal technologies could decrease carbon emissions worldwide while creating a strong export market with attendant creation of jobs in the U.S.

Jan 1, 1998

By S. Potgieter-Vermaak, T. T. Chiweshe, W. Purcell

Complete isolation of chromium (III) from the reference material (SARM 131), Upper Group 2 (UG2) chromite ore, and Merensky Reef mineral ore was achieved using ammonium phosphate salt as flux. Optimum pH (3.2–3.8) conditions and sample to flux ratios (1:25) were some of the factors that were critical for the complete isolation of chromium. Increasing the sample to flux ratio (1:50 excess) however resulted in the conversion of all the elements in the melt into a green solution (pH, 5.8–6.7). A different chromium compound was subsequently isolated from the green solution by allowing this solution to stand in an open vessel in a cupboard for a month during which time the pH decreased to pH 3.5–4.2. Quantitative analyses of chromium from the isolated precipitates of SARM 131, UG2 chromite ore, and Merensky Reef mineral ore indicated chromium contents of 41.87, 60.41, and 23.93% respectively which were very close to the chromium content in the original samples. Analysis of the chromium precipitates using IR indicated the presence of phosphates (1100–1200 cm−1 ) while SEM-EDX analysis showed the presence of microscopic crystalline particles with Cr, P, and O as the major elements. Further characterization of the chromium precipitates using XRD and Raman successfully identified the product as chromium (III) metaphosphate C-type (Cr(PO3)3, JCPDS no. 01-077-0672), in the isolated chromium precipitates.

By N. Arbiter

Introduction The theoretical analysis of tumbling mill energetics and performance has largely neglected mill dimensionality, and, in particular, the importance of the length/diameter (L/D) ratio. This is in spite of the fact that practice varies substantially: geographically, for semi-autogenous and autogenous mills, as between North America and South Africa/Scandinavia, and historically, for overflow ball mills, for which the L/D ratio has increased significantly from the earliest small mills to the largest mills currently. The present study is concerned primarily with the influence of the L/D ratio on the design and operation of overflow ball mills, on the occurrence of the overload phenomenon, and on the limits, if any, it may impose on mill capacities because of critical pulp axial velocity limits. It will be shown that the shape factor is of major importance in this area and that its adjustment to the extent that this is practical should remove the diameter limitations previously postulated for this mill type. Dimensionality in mill design Ball mill shape factors in the period prior to 1927 (Taggart, 1927) averaged 1.1/1 for 29 center discharge mills and 1.0/1 for 30 peripheral discharge mills. With the resumption of new plant construction after the 1930s depression, the Morenci concentrator continued the 1/1 ratio with its 3.1 x 3.1 m (10 x 10 ft) mills. The ratio was increased progressively from then on, reaching 1.6 and 1.8/1 for the largest overflow mills currently. As shown recently (Arbiter, 1989), this is in sharp contrast to autogenous and SAG mill shapes, for which the ratio averages 0.4 in North America. On the other hand, South African practice, starting at the turn of the century with autogenous mills having 4/1 ratios, moved toward 1/1 until recently, when a 2.5/ 1 ratio mill was installed. The reasons given for such divergent practice for mill shape factors are in some respects contradictory and generally inconclusive. The most complete discussion from a practical viewpoint (Dor and Bassarear, 1982) is limited to primary SAG and autogenous mills. Considerations of ball mill dimensionality have had a twofold direction. On the one hand, it has been argued that ball mill efficiencies should increase with increasing diameter and that the specific energy for a particular grind should be reduced accordingly. An inadvertent test of this idea at the Bougainville operation (Burns and Erskine, 1983) resulted in drastic underpowering, which led to failure to reach design capacity until additional mills were installed. This can be taken as strong evidence against any increase in efficiency with diameter. In another direction, it has been argued (Arbiter and Harris, 1982, 1983) that there is a limit to ball mill diameters because of the demonstrable limit to axial flow velocities evident in the overload phenomenon, which as a fact is incontrovertible. But that it places a limit on mill diameters overlooks the evidence given below that appropriate variation in the L/D ratio will permit major increases in diameter, limited only by constructional or economic factors. The present study was directed toward quantifying the overload phenomenon through examination of the influence of mill dimensionality variation and mill operating variables on its occurrence. It is shown that varying the operating conditions, specifically the load fraction and the fraction critical speed, can reduce the risk of overload for existing operations; while appropriate decreases in the L/D ratio can minimize the risk in the design of new circuits. Ball mill overload Ball mill overload is a consequence of the approach to a critical velocity with increasing feed rates or circulating loads. Although the effect has been known for over 50 years, there have been no previous attempts to quantify it. The following description of the ball mill as a flow system is the preliminary to a quantitative analysis: 1) In the absence of a ball load, axial flow of pulp through a mill resembles open channel flow, except for disturbances near the shell due to shell/lifter rotation. 2) For a given ball load (Lf), the void fraction available for pulp hold-up (H) for the ascending portion of the load is approximately 0.4 Lf. In the descending portion, it is greater than this and increases with fraction critical speed (Fc) because of load expansion. 3) Increasing the feed rate increases pulp hold-up and progressively fills the available void space. At a critical flow rate, which depends on system geometry, hydraulic head and pulp rheology, void filling reaches its limit; a pool forms rapidly and fills available space outside the ball load and up to the overflow level. Prior to this, pulp discharges mainly along the ascending rim of the overflow. 4) For a small mill (Lo et al., 1990), it has been shown that with increasing feed rates the critical filling is at or near 50% of the mill volume. Power drops rapidly when this level is reached, as required by the torque formula. 5) The transition to overload is associated with the following phenomena: a) The decrease in power draw. b) Damping of mill sound. c) Reduced comminution of coarser feed sizes, probably due to reduced direct impact in the presence of a pool. d) Increased circulating loads, which further intensify the overload, and increased density of cyclone underflows, which can lead to roping. e) Conditions beyond overload are not known because feed rates are not delibelrately increased beyond this point. f) The existence of the phenomenon limits the capacity of a mill with a fixed set of operating conditions and can prevent the balancing of hard ore feed rate decreases by increases in soft ore rates.

Jan 1, 1992

By F. N. Siddiquie, Mohd Shaif, Rajiullah Khan, Juned Alam

Manganese ore bodies of Banswara Mn belt were classified into stratiform and stratabound types, based on their mode of occurrence, distribution, and their chemical characters. These ore bodies generally composed of braunite, pyrolusite, cryptomelane/ psilomelane, wad, etc. The stratiform-type Mn ore bodies are conformable with the associated host rocks (Mn phyllite, etc.) and occurred in the form of layers, bands, etc., which are variable in their shape and size. These ore bodies are also strongly folded with the enclosing host rocks. The others, which are stratabound-type Mn ore bodies, also showed an intimate association with the associated host rocks. These types of ore bodies occurred in thin layers, pockets, lenses, stringers, etc. The classified ore bodies are confined with Kalinjara formation of Aravalli Supergroup of Paleoproterozoic age. The ore bodies are structurally controlled and well associated with phyllite, schist, limestone, quartzite, etc. The stratiform-type ore bodies constitute a marginal to low Mn grade and are also characterized by lower Mn content (26.19–39.24%) along with the Mn/Fe ratio of 7.16–12.23, while the stratabound-type Mn ore bodies are rich in Mn (35.92–49.64%) along with the higher Mn/Fe ratio of 14.15–23.97. However, the poor Mn grade along with high siliceous impurities of Banswara Mn deposits is subjected to them for intermittent mining activities in the past and, consequently, did not attract the scientific and industrial community for the evaluation of these resources. Therefore, the authors attempted this study in a scientific and systematic manner (mode of occurrence/distribution and possible methods for evaluation/exploration) to evaluate the potential of existed and newer Mn deposit resources in the Banswara Mn belt. The whole findings would be very much helpful for exploration/ mining geologist along with other concerned, to completely evaluate these Mn deposits in the future.

Aug 16, 2021

By Erik S. Bernard

"INTRODUCTION Conventional steel bar reinforcement is used in many tunnel linings to provide high flexural and tensile load resistance. These Reinforced Concrete (RC) tunnel linings may suffer flexural cracking during service or, in the case of precast concrete segments, during production, handling, or installation. Cracks can lead to corrosion of steel reinforcement, so limits are placed on maximum acceptable crack widths to reduce the likelihood of corrosion during the intended design life (AFTES, 2013; MC2010, 2012). However, the relatively light level of reinforcement used in many applications can result in quite wide in-service crack widths, so either additional steel bar reinforcement is required to limit maximum crack widths, or fibers can be included to control crack widths. Numerous investigations have been undertaken into the efficacy of including steel fibers to reduce crack widths in conventionally reinforced members (Stang and Aarre, 1992; Abrishami and Mitchell, 1997; Bischoff, 2003; Dupont and Vandevalle, 2003; and Jansson et al, 2010), but steel fibers suffer the problem that they are at least as sensitive to corrosion at cracks as steel bars and therefore have similarly tight limits placed on acceptable crack widths (AFTES, 2013). An alternative means of maintaining narrow crack limits in RC members has therefore been sought. The current investigation was instigated following an observation that theories promoted as an explanation for the ability of steel fibers to reduce crack widths in reinforced concrete flexural members (Deluce et al, 2014) do not depend on the material composition of the fibers used but instead depend primarily on the tensile stress generated by the fibers across cracks. Since it is known that macro-synthetic fibers are capable of equaling the post-crack tensile capacity of steel fibers, it has been hypothesized that macro-synthetic fibers are also capable of reducing crack widths in reinforced concrete flexural members but with the added advantage that macro-synthetic fibers are completely immune to the effects of corrosion. Use of macro-synthetic fibers to reduce maximum crack widths in reinforced concrete flexural members subject to aggressive environmental exposure is more rational than use of steel fibers because steel fibers are very sensitive to the corrosive effects of environmental exposure at cracks. The current investigation was therefore undertaken to explore the potential use of macro-synthetic fibers to reduce maximum crack widths in reinforced concrete members subject to flexure. Barchip BC54 fibers were selected as they are one of the most widely used and competitive high performance macro-synthetic fibers currently available."

Jan 1, 2016

By Taghi Sharizadeh, MAURICE SUNKPAL, ELAHEH TALEBI, PEDRAM ROGHANCHI

Excessive heat exposure is among the health and safety hazards that have adverse effects on the mine workers. The very nature of the underground climate makes it a convenient avenue for heat generation and accumulation from several heat sources including autocompression, equipment, and heat from strata. This study investigated the effects of clothing insulation and acclimation on the thermal comfort ofmineworkers who are exposed to heat in underground working environments. Several clothing ensembles have been considered to analyze the effect of the thermal resistance of clothing on the thermal comfort of workers. To investigate the impact of the clothing insulation, the thermal comfort limit of an underground miner was calculated in the form of maximum allowable exposure time for an 8-h shift. Parametric analyses were subsequently performed using an already developed thermal comfort model using MATLAB software. The results demonstrate that clothing insulation has a significant effect on the thermal comfort of mine workers. Increase in the clothing insulation decreases the maximum allowable exposure time of mine workers. This is especially true for the new and non-acclimated workers. Since acclimatized workers can tolerate a higher level of the dehydration and are capable of losing more water by sweat per shift, the maximum allowable exposure time for the acclimated workers are higher than non-acclimated workers. These analyses have shown that acclimated workers can have more continuous work per shift compared with non-acclimated workers. For example, in an environmental condition with clothing that a nonacclimated worker cannot work more than 5 h, an acclimated worker can work a full 8-h shift.

Jun 29, 2020