Search Documents

By J. A. Organiscak

Longwall mining technological improvements have provided significant increases in productivity over the last 15 years. Longwall productivity is anticipated to continue to escalate with expanded application of automated equipment. Automation technology that will likely be adopted over the next 5 years is memory cut with shearer initiation of shield movement supervised by a couple of face workers. Operations using this technology will most likely relocate many production workers from the face to the outby gate entries and position several face workers outby the shearer, exposing workers to different health and safety risks. These changing risks are primarily related to worker relocation and expected increased production levels. Workers outby the face will most likely have less dust and noise exposure, but will be exposed to other safety hazards associated with outby equipment movement, materials handling, and gate entry ground movements. The face workers will most likely be exposed to higher respirable dust and noise levels generated by the equipment at elevated production rates. Methane gas emission is also expected to increase with faster mining rates. These operational changes and the control technologies needed to reduce redefined longwall worker hazards at semiautonomous longwall operations require examination to maintain the health and safety of mine workers.

Jan 1, 1996

By Michael A. Werner

"A Yieldable Structure for Use in Areas of High Rock Stress & Deformation." Rock stress of up to 9000 psi have been recorded in the mines of the Coeur d'Alene Mining district. Associated with these large stresses are rock fractures and deformation. In order to maintain openings required for mining, large wood preparation structures are constructed to provide access to the work areas for men and materials. These wood raise preparation structures are costly to construct and maintain. Therefore a steel-foam concrete structure was designed and proposed for testing which would be less costly to construct, require no maintainence and maintain its structural integrity while allowing up to 53 inches of wall rock deformation.

Jan 1, 1984

By H. Wagner

Recently a detailed study ?Minerals Planning Policies and Supply Practices in Europe? has been completed. The study, conducted on behalf of DG Enterprise, demonstrated that there are very few written down national minerals policies within European Union. Mineral policy elements are dispersed in many different documents and acts. The paper discusses the essential elements of minerals policies; particularly importance is placed in issues related to planning (land use planning, mineral development, etc.). A number of examples of successful and less successful mineral planning policy approaches are presented in other to support the idea of importance of comprehensive mineral policy. The main sources of information were the country reports of 26 European countries that are appendix of the study. We conclude that comprehensive written mineral policy that incorporates essential elements is crucial in order to achieve secure minerals supply.

Jan 1, 2007

By C. E. Jordan

The U.S. Bureau of Mines investigated flotation hydrodynamics to improve the recovery of coarse phosphate. Fluid velocity profile measurements were used to characterize the hydrodynamics within commercial phosphate flotation cells and laboratory flotation cells. The effects of agitation, aeration, and pH on coarse phosphate recovery were measured in the laboratory flotation cells and correlated with the hydrodynamics measurements. Test results revealed that the agitation energy and aeration level had a significant effect upon flotation response. By optimizing these two parameters, 92 pct of the phosphate was recovered in a rougher flotation concentrate grading 28 pct P2O5?

Jan 1, 1994

By JOHN HOMER, Jacob L. Carr, Jonathan K. Hrica, Kathleen M. Stabryla, Iman Benbourenane, Jennica L. Bellanca

Given the recent focus on powered haulage incidents within the US mining sector, an appraisal of collision avoidance/warning systems (CXSs) through the lens of the available research literature is timely. This paper describes a rapid review that identifies, characterizes, and classifies the research literature to evaluate the maturity of CXS technology through the application of a Technology Readiness Assessment. Systematic search methods were applied to three electronic databases, and relevant articles were identified through the application of inclusion and exclusion criteria. Sixty-four articles from 2000 to 2020 met these criteria and were categorized into seven CXS technology categories. Review and assessment of the articles indicates that much of the literature-based evidence for CXS technology lies within lower levels of maturity (i.e., components and prototypes tested under laboratory conditions and in relevant environments). However, less evidence exists for CXS technology at higher levels of maturity (i.e., complete systems evaluated within operational environments) despite the existence of commercial products in the marketplace. This lack of evidence at higher maturity levels within the scientific literature highlights the need for systematic peer-reviewed research to evaluate the performance of CXS technologies and demonstrate the efficacy of prototypes or commercial products, which could be fostered by more collaboration between academia, research institutions, manufacturers, and mining companies. Additionally, results of the review reveal that most of the literature relevant to CXS technologies is focused on vehicle-to-vehicle interactions. However, this contrasts with haul truck fatal accident statistics that indicate that most haul truck fatal accidents are due to vehicle-to-environment interactions (e.g., traveling through a berm). Lastly, the relatively small amount of literature and segmented nature of the included studies suggests that there is a need for incremental progress or more stepwise research that would facilitate the improvement of CXS technologies over time. This progression over time could be achieved through continued long-term interest and support for CXS technology research.

Jun 17, 2022

By G. W. Luxbacher

Coal mine infrastructure is rarely designed solely on the basis of ventilating the underground workings. Instead the optimization of a mining sequence, the minimization of coal quality variation, reduction of coal losses by adapting to property boundaries and geologic structure (seam inclination, roof conditions, coal thickness, etc.) or other similar considerations have formed the objective for mine plant design and layout. Infrastructure development may also reflect a desire to maximize production early in the life of the mine or to permit flexibility in mining according to market conditions. Requirements for coal mine ventilation, established by the 1969 Coal Mine Health and Safety Act, have mandated changes in the traditional concepts of mine plant design in the United States. Mines, in operation prior to the passage of the Act have experienced severe limitations when attempting to adapt the existing mine infrastructure to meet the requirements of the law. In addition the increased quantities of air required, velocity limitations on trolley haulage and belt lines, the establishment of separate intake escapeways and gob area ventilation have com- pounded the inherent complexity in planning mine ventilation systems. Past practices in mine ventilation planning and design are no longer adequate. Given the complexity of today's ventilation systems, effective planning and design approaches are required. As such, the interrelationship between the overall coal mine plant design and ventilation system design is examined. An approach to ventilation system design constrained by global considerations of mine plant design, is presented. The proposed approach is, however, applicable to the design of new mine ventilation systems as well as to the modification of existing systems.

Jan 1, 1980

By T. P. Meloy

Riffles on a shaking table have a major effect on particle separation. This effect is modeled in a spreadsheet.

Jan 1, 1993

By W. G. Pariseau

"BACKGROUND Strata mechanics of three underground coal mines in central Utah were recently studied using a specialized finite element technique [1, 2, 3, 4]. The purpose of these studies was to examine relationships between mining and related seismicity. The longwall mining method was predominant, but room and pillar mining and barrier pillar mining were also used in the mines studied. In every case, high correlation between face advance and seismicity was observed. The specialized finite element technique allows for whole mine subsidence estimation at a kilometer scale and for stress concentration at a meter scale near a working face. Comparisons of observed mine subsidence with model subsidence allows for model verification and justifies detailed analysis of the evolution of stress at seam level. Yielding is expected near a longwall panel face and as the face is advanced the extent of yielding is expected to increase. The total number of element failures in a finite element mine model also increases, so a high correlation with associated seismicity, say, event count, is not so surprising. A brief review of recent coal mine studies in Utah is presented in the sequel. The procedures are given in some detail in application to trona mining. COAL MINES The analysis procedure begins with the geologic column and proceeds to specification of strata properties including elastic moduli and strengths. Joints are an integral part of the geologic model and joint set specifications include dip direction, dip, spacing, stiffness and strength. Spatial variability of strata properties in situ may be taken into account during analysis. Topography is important, especially to Utah coal mines that are developed from outcrop in regions of high relief. Mesh generation follows specification of data input. Finite element analysis is next, followed by reporting of results. In this regard, all finite element computations are based on first principles. No model “calibration” is done that involves adjusting computer input to obtain a fit to mine measurements such as subsidence profiles. Figure 1 illustrates the concept of a dual node – dual mesh finite element concept. Dual nodes are roof and floor nodes in mined areas. These nodes replace the seam. The dual mesh is a much refined mesh with displacement boundary conditions obtained from the big mesh and thus replaces the effect of mining in the region outside the dual mesh. The refined dual mesh allows for details of stress, strain and displacement near a working face of interest. Strata Properties Strata properties include elastic moduli and strengths of intact rock between joints and joint stiffness and strength for each joint set present. Both properties sets may be obtained from laboratory test data, although testing joints poses a sampling problem in the field. The statistical variability observed in laboratory test data, say, in unconfined compressive strength tests is often characterized by much variation. In fact, the coefficient of variation, ratio of standard deviation to mean, is often greater than 35 percent. When sample values are mapped back to the mine location, one may observe spatial variability as properties vary from place to place as shown in Figure 2. Spatial variability may be incorporated into a finite element analysis with probabilistic assignment of properties to elements in accordance with measured variability. The result is a more realistic model of rock in situ."

Jan 1, 2017

By Ma Fangyuan, Li Min, Xu Bing, Xian Yushuai, Zhao Tonglin

The study explored a new combination amine collector (XK-28) that can obtain better flotation index and defoaming rate for magnetic iron ore. A pure quartz mineral test indicates that dodecylamine, XK-I, or XK-II has good collection effect on quartz and their best flotation pH is in the range of 6–7. The experimental results of a combination collector (XK-I:XK-II = 2:8.) show that the separation effect for quartz and magnetite is better than that of a single collector. The single factor for actual mineral test shows that when the combined reagent is used as the collector, the best conditions are pH = 7, 90 g/t dosage, and XK-I:XK-II = 2:8, which is consistant with the pure mineral test. The difference for dodecylamine as a collector is that the optimal dodecylamine dosage is 60 g/t. Under the best conditions of actual ore test, dodecylamine and XK-28 are respectively used as the collector to compare the flotation indexes. Study results indicate the magnetite grade using XK-28 as the collector is higher by 3.02% than that of using dodecylamine, recovery is increased by 1.92% over that of using dodecylamine. Based on the measurement results of zeta potential, uses of XK-28 can slightly increase the zeta potential difference of quartz and magnetite to enhance the flotation effect. The mechanism of action between the XK-28 collector and the actual ore from the Gongchangling plant is physical adsorption, and this adsorption also has hydrogen bond formation. Contact angle results shows that XK-28 improves the hydrophobicity of quartz better than dodecylamine. Compared with dodecylamine, XK-28 is more sparsely arranged on the surface of the foam. The foam produced by the XK-28 collector has better air permeability and it is more likely to merge and disappear with bubbles.

Jul 21, 2021

By MATTHEW HART, THOMAS BAMFORD, Kamran Esmaeili, MICHAL KOWALCZYK, FILIP MEDINAC

Improved haul-road conditions can have a positive impact on mine operations, resulting in heightened safety, productivity gains, longer tire life and lower maintenance costs. For these reasons, a monitoring program is required to ensure the operational efficiency of the haul roads. Currently, at Bald Mountain Mine, monthly site severity studies, ad hoc inspections by frontline supervisors or operator feedback reporting are used to assess road conditions. These methods are subjective and provide low temporal resolution data. This case study presents novel unmanned aerial vehicle (UAV) technologies, applied on a critical section of haul road at Bald Mountain, to showcase the potential for monitoring haul roads. The results show that orthophotos and digital elevation models can be used to assess the road smoothness condition and to check the road design compliance. Moreover, the aerial mapping allows detection of surface water, rock spillage and potholes on the road that can be quickly repaired/removed by the dedicated road maintenance team.

By S. Potgieter-Vermaak, T. T. Chiweshe, W. Purcell

Complete isolation of chromium (III) from the reference material (SARM 131), Upper Group 2 (UG2) chromite ore, and Merensky Reef mineral ore was achieved using ammonium phosphate salt as flux. Optimum pH (3.2–3.8) conditions and sample to flux ratios (1:25) were some of the factors that were critical for the complete isolation of chromium. Increasing the sample to flux ratio (1:50 excess) however resulted in the conversion of all the elements in the melt into a green solution (pH, 5.8–6.7). A different chromium compound was subsequently isolated from the green solution by allowing this solution to stand in an open vessel in a cupboard for a month during which time the pH decreased to pH 3.5–4.2. Quantitative analyses of chromium from the isolated precipitates of SARM 131, UG2 chromite ore, and Merensky Reef mineral ore indicated chromium contents of 41.87, 60.41, and 23.93% respectively which were very close to the chromium content in the original samples. Analysis of the chromium precipitates using IR indicated the presence of phosphates (1100–1200 cm−1 ) while SEM-EDX analysis showed the presence of microscopic crystalline particles with Cr, P, and O as the major elements. Further characterization of the chromium precipitates using XRD and Raman successfully identified the product as chromium (III) metaphosphate C-type (Cr(PO3)3, JCPDS no. 01-077-0672), in the isolated chromium precipitates.

"The Ohio River Bridge East End Crossing Tunnel requires a 75-year service life of its cast-in-place reinforced concrete lining. This twin-tube 3-lane (each tube) highway tunnel is about 55-ft wide and 30-ft high. Since unified tunnel service life prediction methodology does not exist in the US, challenges occurred during the design-build phase of this project. These challenges include the methodologies in determining the reinforced concrete’s degradation mode, the lining’s surface chloride concentration level, the reinforcing steel’s critical chloride threshold value for corrosion, how to verify the concrete’s diffusion coefficient, and the durability impact from concrete crack width. This paper presents a methodology in verifying the proposed concrete mix can achieve the service life requirements. This methodology can be adopted for service life prediction for future tunnels to be built in the US. INTRODUCTION The Ohio River Bridge East End Crossing (ORBEE) Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining system includes: •,Nominal 16” cast-in-place reinforced concrete lining, with 2” and 3” concrete covers over reinforcing steel for its extrados and intrados, respectively. •,20” cast-in-place reinforced concrete invert slab, with 4” and 3” concrete covers over reinforcing steel on its top face and bottom face, respectively. •,PVC waterproofing system around tunnel perimeter, excluding invert slab. •,Perforated PVC groundwater collection pipes on both sides of the tubes and one below the invert slab of each tube."

Jan 1, 2016

By Michael Gauna

A high seam geologic condition exists at Jim Walter Resources No.4 mine which requires immediate rib support after a continuous miner cuts a place, High seam mining heights are typically 2.4 to 2.6 m (8 to 9 it) and a thick rock layer is present in the upper portion of the coal rib side. The 610 m (2000 ft) mining depth at No. 4 mine induces horizontal rib line movement after excavating an entry. Horizontal rib movement greater than 30.5 cm (12 in) have been noted. When lateral movement occurs in the high seam areas, the thick rock layer, and the coal above the rock layer, become fractured and tend to roll into the entry. If not adequately supported, large rib rolls develop in the place being bolted as well as in previously mined areas which endanger men and equipment. To control this situation rib support must be installed in the roof bolting operation as the bolting crew works towards the face. A rib control system has been developed for this high seam mining condition utilizing a mechanical anchor bolt placed at an angle in the rib and installed with a modified Fletcher DDFI- 15 bolting machine. Over 120 km (75 mi) of entry have been supported with angle rib bolts. These angle bolts constitute 43 to 60% of the total roof and rib bolt footage in the high seam port- ions of No.4 mine. The angle rib bolting system has proven safer, more effective, and more efficient than the earlier support method employing bolts installed horizontally into the rib. No rib roll accidents have occurred since the angle drill bolting machines were placed in service in 1981. By securing the broken rib material with an angle bolt anchored above the coal pillar, a more effective means of rib control is achieved. Angle rib bolting does not interfere with continuous miner productivity. In addition, bolting crews are now reduced from three to two people and the total drilling supply costs are approximately 60% the previous cost, when compared to the previous support method using horizontal rib bolts.

Jan 1, 1983

By D. McCarthy

This paper discusses the process involved in developing an optimum method of treating and removing heavy metals from water that have leached out from the native rock -prior to discharge back into the environment. Also designed into the system is a manner to stabilize the metals removed as a precipitate, so that they can be disposed of as a non-hazardous waste.

Jan 1, 1992

By O. K. Brown

U.S. Borax has two tailings disposal requirements which are uniquely different in many respects, but with the common goal to minimize the impact on the environment, utilize dependable technology and minimize the economic impact. The existing borax mine in the grid Mojave desert of Southern California has gone through a series of changes in tailings disposal practices in the 56 years of operations, The other tailings disposal requirement is a new molybdenum mine, presently in the feasibility phase, in the high precipitation setting of Southeast Alaska. II. Introduction U.S. Borax is faced with two tailings disposals situations, at diverse locations:

Jan 1, 1984

By A. E. Koski

This paper describes the implementation of specialized software in mine planning at the Cleveland-Cliffs' managed Empire Mine on Michigan's Marquette Iron Range. The application puts together years of mining experience on the eastern end of the Marquette Range beginning in the early 1960's. The Empire Mine, in its thirty-fifth year of production, uses the software to model a complex and highly variable low grade magnetite ore body, capturing the economics of mining and processing to the final product. With special attention given to geostatistical methods, the software is used for all geologic modeling, ore reserve estimation, ore control, pit design and short and long range planning.

Jan 1, 1999

By T. Braun

A greenfield open pit gold mine in Latin America suspended operations less than three years into an eight-year mine plan after a waste rock dump and heap leach facility sustained substantial damage from a deep-seated landslide. No injuries to employees were recorded because of the slow-moving failure. Due to early detection by the operations team, the owner had sufficient notice of the potential failure and successfully rinsed the heap leach facility prior to the failure event. Engineers estimated approximately 35 million cubic meters of mass movement below the waste rock and heap leach facilities. The original eight-year mine plan produced approximately 60,000 ounces of gold per year. After the failure, the owner terminated gold production, re-configured the mine site to a safe, standby condition and launched a detailed investigation into the root-cause of the failure. Approximately two years after the shutdown, legal interests filed a statement of claim and named three engineering design firms and individuals involved in the project. Several years of litigation, including discovery and deposition proceedings, followed as the legal process considered evidence spanning a 20-year timeline. Changes in project ownership and consulting firms during the development and operations phase complicated the process. In 2017, the plaintiff and last defendant settled. The author was involved as the corporate representative for one of the engineering design firms.

Mar 2, 2022

By F. N. Siddiquie, Mohd Shaif, Rajiullah Khan, Juned Alam

Manganese ore bodies of Banswara Mn belt were classified into stratiform and stratabound types, based on their mode of occurrence, distribution, and their chemical characters. These ore bodies generally composed of braunite, pyrolusite, cryptomelane/ psilomelane, wad, etc. The stratiform-type Mn ore bodies are conformable with the associated host rocks (Mn phyllite, etc.) and occurred in the form of layers, bands, etc., which are variable in their shape and size. These ore bodies are also strongly folded with the enclosing host rocks. The others, which are stratabound-type Mn ore bodies, also showed an intimate association with the associated host rocks. These types of ore bodies occurred in thin layers, pockets, lenses, stringers, etc. The classified ore bodies are confined with Kalinjara formation of Aravalli Supergroup of Paleoproterozoic age. The ore bodies are structurally controlled and well associated with phyllite, schist, limestone, quartzite, etc. The stratiform-type ore bodies constitute a marginal to low Mn grade and are also characterized by lower Mn content (26.19–39.24%) along with the Mn/Fe ratio of 7.16–12.23, while the stratabound-type Mn ore bodies are rich in Mn (35.92–49.64%) along with the higher Mn/Fe ratio of 14.15–23.97. However, the poor Mn grade along with high siliceous impurities of Banswara Mn deposits is subjected to them for intermittent mining activities in the past and, consequently, did not attract the scientific and industrial community for the evaluation of these resources. Therefore, the authors attempted this study in a scientific and systematic manner (mode of occurrence/distribution and possible methods for evaluation/exploration) to evaluate the potential of existed and newer Mn deposit resources in the Banswara Mn belt. The whole findings would be very much helpful for exploration/ mining geologist along with other concerned, to completely evaluate these Mn deposits in the future.

Aug 16, 2021

By S. A. Sanderson

The last two decades have witnessed the resurgence in popularity of a century old tool for shaping laws and public policy – the ballot initiative. In recent years, anti-mining special interests have used the initiative process to secure voter approval of measures to ban modern surface mining for gold and silver. In November 1998, voters in Montana approved such a measure1 – the effects of which have been devastating to the mining industry in that state. In November 1999, anti-mining groups sought to place a nearly identical provision on the general election ballot in Colorado. They did not succeed, but the battle over mining’s future continues in the most important forum of all – the court of public opinion. The Colorado measure failed, in large part, because its proponents failed to convey a positive environmental theme. The mining industry also exercised early-on the rights available under state law for administrative and judicial review of the initiative, instead of relying upon the limited relief that would have been available had it waited until after the secretary of state approved the measure for the November election ballot. This article will summarize the ballot initiative process in Colorado and the proceedings that took place over Initiative No. 215.

Jan 1, 2001

By Taghi Sharizadeh, MAURICE SUNKPAL, ELAHEH TALEBI, PEDRAM ROGHANCHI

Excessive heat exposure is among the health and safety hazards that have adverse effects on the mine workers. The very nature of the underground climate makes it a convenient avenue for heat generation and accumulation from several heat sources including autocompression, equipment, and heat from strata. This study investigated the effects of clothing insulation and acclimation on the thermal comfort ofmineworkers who are exposed to heat in underground working environments. Several clothing ensembles have been considered to analyze the effect of the thermal resistance of clothing on the thermal comfort of workers. To investigate the impact of the clothing insulation, the thermal comfort limit of an underground miner was calculated in the form of maximum allowable exposure time for an 8-h shift. Parametric analyses were subsequently performed using an already developed thermal comfort model using MATLAB software. The results demonstrate that clothing insulation has a significant effect on the thermal comfort of mine workers. Increase in the clothing insulation decreases the maximum allowable exposure time of mine workers. This is especially true for the new and non-acclimated workers. Since acclimatized workers can tolerate a higher level of the dehydration and are capable of losing more water by sweat per shift, the maximum allowable exposure time for the acclimated workers are higher than non-acclimated workers. These analyses have shown that acclimated workers can have more continuous work per shift compared with non-acclimated workers. For example, in an environmental condition with clothing that a nonacclimated worker cannot work more than 5 h, an acclimated worker can work a full 8-h shift.

Jun 29, 2020