Search Documents

By S. C. Suboleski

Underground long-range planning and mine design is an iterative process beginning with a specified production level, quality criteria, and geology of the deposit. Given these factors, face equipment is selected, the number of units needed and production per unit are calculated, and the mine infrastructure needs are developed. The scheduling of units then follows, with the design of the various support systems coming next. The support systems needed to maintain production can be grouped as follows: (1) outby haulage of mined material, (2) supply and manpower haulage, (3) ventilation and associated environmental considerations, (4) drainage, fresh water, and related considerations, (5) rock mechanics, and (6) power, supply. Thus, long-range planning may be viewed as a three-tiered structure, with the data on required production, product quality, and geology at the upper level; the development of face production capacity and the scheduling of units sufficient to meet the needs of the first two at the second level; and the development of support operations for the production units at the third level. Changes at any level may affect not only the items on that tier but may also cause a change to the items on the tier above and below. For example, if the rock mechanics data indicate that desired opening sizes will not be stable, then this situation will affect not only the ventilation design but also the production rate and possibly the selection of equipment itself. These, in turn, may affect the scheduling of units and the number of units, ultimately influencing the entire third tier of systems.

Jan 1, 1979

By J. J. Gusek

Passive treatment of mine drainage using constructed wetlands has been employed on coal and metal mine sites since about 1985. The technology has advanced significantly since then; there are currently over 600 of these systems treating coal mine drainage in the Eastern U.S. at flow rates of hundreds of liters per minute. Passive treatment performance at three metal mines discussed in this paper has been positive for a wide variety of flows, water chemistry, and climates. The sites include a high-altitude underground copper mine, acidic seepage from a gold heap leach pad, and pumped effluent from an active underground lead mine in Missouri.

Jan 1, 2000

By T. Y. Yan

O2, NaCl03, H202, NaOCI and Ce+4 have been examined as oxidants in an alkaline carbonate system for uranium in situ leaching. The South Texas and New Mexico ores contained up to 2.6 meq/g of reducing compounds that consume oxidants in the leaching operation. Leaching rates did not increase linearly with the oxidation potential of the oxidants. A mild oxidant can be used to maximize uranium oxidation selectivity and oxidant efficiency. 02 can oxidize most of the uranium mineral with an adequate rate and high oxidant efficiency.

Jan 1, 1993

By J. H. Gwynne

[ ]

Jan 1, 1962

By A. W. Czarnowsky

More than ever before, mining projects are besieged from growing regulatory, political, public, and special interest group pressure. Administrative and legal appeals to permits and environmental documents can delay project start-up and add tremendous cost to mineral development. Some mining projects have been canceled given undue external constraints. Successful managers must learn to cope with these constraints. This paper will discuss controversy and present a number of environmental management tips to minimize the potentials for delay and to lessen the impacts from government and anti-mining pressures.

Jan 1, 2001

By F. W. Mueller

It seems to be a matter of general understnading that title extraction or use of ground water may not be used as the basis of a depletion deduction under the United States Revenue Code And indeed, I have been unable to find any precedent upon which to base such a deduction. It is for this reason that the Shurbet case, which is the subject of my discussion and is now before the Court, may well become a precedent as authority for the allowance or disallowance of a depletion deduction for income purposes. It is well known that the law recognized that capital is consumed in the process of extracting minerals, oil and has, other natural deposits, and timber (underscoring supplied). This exhaustion, or depletion, is likened to the using up of raw materials in manufacturing. The law, therefore, provides a deduction for depletion which is intended as compensation for the exhaustion of assets consumed in the production of income through severance of minerals, oil and gas, other natural deposits, and timber.

Jan 1, 1962

By J. C. Irvine

A recent development in underground drilling has been the introduction of the down-the-hole drill, an old and very familiar tool to the surface operator. The idea of moving such a rig underground is not new. Tests were conducted at INCO in Canada and Mt. Isa, Australia in the early 1960's, and St. Joe used one for underground exploration in their Missouri lead mines in the mid-1960's. However, the trend to full scale production programs did not start until the mid-1970's. The first successful North American test was at INGO in early 1973. This led to a large-scale pillar recovery and open stoping program which en¬compassed 25 drilling units by mid-1976. Meramec Mining Company tested a unit using air boosted up to 200 psi (140, 000 kg(m2) in the summer of 1973 which by 1976 led to an open stope and pillar drilling program using 12 units. By mid-1976, production units using boosted air were also in use at Pilot Knob in Missouri and at St. Joe in Balmat, New York. Experimental and utility units were in use in several other mines and down-the-hole drills were being seriously considered for at least one major new underground mine.

Jan 1, 1976

By G. D. Naugle, L. C. Atkinson

Introduction Deep open-pit mines invariably affect the local and regional hydrologic systems. Pit dewatering, occurring during mining operations, puts an obvious hydrologic stress on these hydrologic systems. However, post-mining hydrologic impacts resulting from the pit refilling with groundwater following the cessation of mining activity can also be significant. The prediction of the rate at which the post-mining pit will fill with groundwater is a critical aspect of assessing the long-term hydrologic impacts. Numerical groundwater flow modeling provides a method for predicting the groundwater refilling rate of the pit. The rate at which pit "lakes" fill depends on several factors: •the rate and duration of pit dewatering; •the depth and size of the ultimate pit and •the pre-mining hydrologic regime. These factors can be incorporated into a detailed numerical groundwater flow model that can then be used to assess the effects of dewatering and post-mining recovery on the local and regional hydrologic systems. A sufficiently detailed, numerical groundwater model provides the oportunity to: •account for complex geology near the pit; •assess the impact of active pit dewatering and •predict the long-term impacts of post-mining groundwater flow into the pit. A detailed groundwater model incorporating these items has been developed and applied at an operating open-pit mine. Developed by Durbin and O'Brien (1987), the three-dimensional, finite-element, groundwater flow model was used to represent the hydrologic system of an approximately 253-km2 (98-sq mile) area surrounding the pit. Historical groundwater elevation data, stream flows and meteorologic, geologic and geophysical data were used to establish the dimensions and initial conditions for the model. Steady-state conditions, representing the pre-mining local and regional hydrologic systems, were simulated using the initial conditions incorporated into the groundwater model. The groundwater model was then utilized to simulate various dewatering programs, to predict the filling rate and the groundwater depth in the ultimate pit once mining activities are complete and to assess the long-term impacts on the regional groundwater flow system. Development of pit lake model Groundwater modeling efforts were completed in two phases. The first focused on pit dewatering activities, while the second phase concentrated on the post-mining effects on the hydrologic system. The final estimates of groundwater elevations calculated during the pit dewatering simulations were used in predicting the post-mining recovery of the hydrologic system. The groundwater model was also modified prior to the second phase to account for the volume of rock removed during mining activities. To account for the actual volume of rock mined, the geometry of the post-dewatering model grid was modified to approximate the final pit geometry. The depth and width of the ultimate pit were divided into eight idealized stages that represented significant changes in the bench geometries. These eight stages were then introduced sequentially into the model according to the predicted water elevations within the pit. In this way, changes in the volume and depth of water within the pit were accounted for through time. Once the ultimate pit geometry was accounted for in the model, it was necessary to assign new hydraulic characteristics to those parts of the model grid (elements) that represented excavated rock. The solution of the numerical model requires that finite hydraulic conductivity values be assigned to the portion of the groundwater model that represents excavated rock. Therefore, the calculated groundwater elevations differ, somewhat, between the edges and the center of the open pit. These model-calculated water elevations at the edge and in the middle of the open pit represent the elevation of water that would occur in the pit lake. To minimize the error in the estimated level of water within the pit lake, the hydraulic conductivity was increased to a value that would: •minimize the predicted difference between the groundwater elevations across the open pit and •produce a numerically stable solution. Specific storage is the hydrologic parameter that accounts for the water produced by compaction of the aquifer matrix. To predict the groundwater volume that would flow into the ultimate pit, this parameter was assigned a value equivalent to the compressibility of water. This value of specific storage reflects the post-mining groundwater storage occurring as an open body of water. Additionally, a specific yield of 1.0 was assigned to the pit elements to represent the 100% porosity of the open pit. In

Jan 1, 1994

By A. Ferreira Morgado

The sodium smectitic clays (bentonites), have more industrial applications in that class of mineral, a driving force to obtain this mineral. In Brazil, there are several occurrences of smectitic clays, unfortunately they are polycationic, with a distribution of several exchangeable cations, where the cation sodium occurs in minor quantity. In this work, the original polycationic smectitic clay was firstly proper characterized and then treated with sodium carbonate obtaining homoionic sodium smectitic clay. The rheological tests in the optimized sodium smectitic clay showed good results for drilling fluids, typical of a sodium bentonite ones.

Jan 1, 1999

By Craig J. Brown

Despite its great potential utility, ion exchange has only achieved limited application in hydrometallurgy. To a significant extent this is due to the limitations of conventional ion exchange process design as well as the properties of the ion exchange resins themselves. Over the past decade several new ion exchange resins have been introduced with properties that make them potentially very useful for various hydrometallurgical separations. In addition, a novel ion exchange process called Reciprocating Flow Ion Exchange or Recoflo, which has been employed in the metal finishing industry for the last dozen or so years for chemical recovery and effluent treatment, has been shown to offer a number of unique and significant advantages over conventional I.X. technology.

Jan 1, 1984

By J. L. Ellenberger

The U.S. Bureau of Mines has cooperated with Cyprus Casa Grande Corporation Cyprus Casa Grande Mine, Cas a Grande, Arizona, since 1988 to assess the hydrology of an in situ leaching test facility. This work has resulted in an in situ design for leaching copper oxide ore that takes advantage of the increased mineral access associated with poor quality rock surrounding mine drifts. Blasting and bulkheads are used to produce readily-leachable rubble and contain and control solution movement, respectively. The design reduces the need for handling solution under high pressures in an injection/recovery system for in situ leaching of underground ore bodies. Early work at the site recognized a stress redistribution zone and increased transmissivity near drifts. Fracture data from a corehole oriented parallel to the dip of the ore body indicated an increase in fracture frequency around drifts a distance of 21 m (70 ft) away from the 5 m (16 ft) diameter drifts.

Jan 1, 1994

Considerable attention has been given to the restoration of low-level radioactive (<1000 pCl/g) sites contaminated during the early years of the atomic energy program. Current clean-up activities which involve the relocation of contaminated soils to licensed disposal sites have been shown to be very costly due to the large volumes of soils which must be excavated, transported and stored. Recent characterization studies conducted at Virginia Tech suggest that the volume of soil requiring disposal can be greatly reduced using mineral processing techniques such as classification, density separation and froth flotation. This article discusses the application of these technologies for soil remediation and describes a conceptual flowsheet for treating soil samples from two contaminated sites.

Jan 1, 1997

By Joseph W. Johnson

General Electric introduced electric drive systems on 85 ton Off-Highway mining trucks in the early sixties. Due to favorable economics, trucks have increased in size to handle larger payloads. Series Motorized Wheel systems were developed to meet this demand. When the technology was available, General Electric switched from use of Series motors to separately excited motors with the added benefits of static exciters and simplified control. Over 20 years of electric drive experience have been incorporated in the STATEX drive systems, which covers truck sizes from 85 to 220 tons. This paper traces the drive system developments from the early stages to the present and takes a look at what&apos;s ahead.

Jan 1, 1983

By C. C. Clark, D. J. Benton, J. B. Seymour, L. A. Martin

"The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics and alternatives, based on information from injury reports, legacy research, stakeholder input and published literature. The results indicate that jackleg drills are involved in more groundfall accidents in underground metal mines than any other drill, and jackleg-drill-related injuries are most prevalent at the face in the course of installing initial ground support. Practical mechanized alternatives to jackleg drills for drilling and bolting under incomplete support in narrow underground openings have not yet been realized. Small, versatile mechanized bolting equipment needs to be developed to address jackleg-drill-related accidents and improve safety at mines where jackleg drills are being used. IntroductionJackleg drill is a generic name for a handheld, rotary, percussion rock drill equipped with an attached reaction leg to provide stability and thrust (Fig. 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jackleg drills are classified according to the bore size of their pneumatic pistons, which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in.) (Kurt, 1982; Clark, 2012). Jackleg drills typically weigh 46.7 kg (103 lb), but the weight can approach 54.4 kg (120 lb) after being fitted for operation with drill steel and air and water hoses (McKibbin and Clark, 2001). In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in.) diameter holes up to 1.83 m (6 ft) deep in rock."

Aug 1, 2016

By Charles L. Kimbell

Introduction Despite the focus on the so-called "high-tech" and service components of the economy, the minerals industry in 1987 continued to provide the world the overwhelmingly dominant share of the total raw material supply for all manufacturing operations. And, in the form of fertilizers and other soil treatment materials, minerals also supplied indispensable raw materials to ensure continued high production of the agricultural and forestry sectors of the world&apos;s economy. Moreover, the role of minerals as a source of construction raw materials was essential to that sector. On the basis of preliminary and partial statistics on world output of crude mineral commodities, 1987 appears to have been a year of further recovery from the recessional years of 1981-1983. The value of world crude mineral industry production (all mineral commodities including fuels) apparently advanced about 5% to nearly $1.1 trillion in terms of constant 1983 dollars.&apos; That is significantly above the recently revised 1986 level of nearly $1.05 trillion, but still considerably below the record-to-date high of $1.27 trillion set in 1980, as shown in Table 1. That growth in value took place despite relatively flat world oil prices - oil being the most important component of the aggregate, as it has been for decades. There is insufficient information available to assess the total value of processed mineral commodities (refined metals, refined oil, manufactured fertilizers and the like). But a figure of $2.6 trillion (constant 1983 dollars) would be a quite conservative estimate for those materials derived only from primary or newly mined materials. And an additional, as-yet-unestimated increment should be added for processed materials derived from secondary raw materials - scrap and other reclaimed substances. From a world trade viewpoint, minerals and mineral products dominate in terms of tonnage. For example, in 1985, on a weight basis, mineral commodities including fuels constituted more than 58% of all goods moving through the Suez Canal and 53% of all goods passing through the Panama Canal. These waterways cannot accommodate giant tankers and ore carriers. So an even larger share of total oceanic trade is composed of minerals and mineral products. Yet, in terms of value, the share of the total accounted for by these industrial essentials is much lower than that accounted for by other commodities, most notably sophisticated high-tech equipment and other goods with a relatively high per-pound value. Worldwide data on the value of mineral export trade for 1987 is so incomplete at this writing that it is impossible to assess that actual level. Indeed, the compilation of similar available data for 1986 covers only the exports of nations with developed market economies. In 1985, these countries accounted for only 67% of total world exports of all goods. They accounted for only 41% of world exports of major mineral commodities: crude nonmetals; metal ores, concentrates, and scrap; mineral fuels; nonferrous metals excluding gold; and iron and steel. For these developed-market-economy countries, the value of exports of these major mineral commodities declined by more than 10% between 1985 and 1986. Most of the shortfall came as a result of a 26% drop in the value of fuels exports. If these patterns of

Jan 7, 1988

By Sebastian Avalos, Julian M. Ortiz

The long-term mine scheduling is the optimal decision on how to extract and process the mining reserves. The resulting plan is mainly driven by economic, metallurgical, and geological factors. Accounting for their uncertainties leads to a robust solution and the feasibility for economic-risk quantification. In this work, we model the spatial uncertainty of grade distributions of multiple correlated elements, by using a multivariate morphing transformation. The result is a set of multivariate geostatistical realizations of the grades, which honor the conditioning data, the direct and cross variograms, and the multivariate statistical distribution, inferred from a set of samples. These models are the input in a reinforcement learning framework, adopted to train a deep neural network that considers the grade uncertainty and leads to an optimum mine plan after training using deep Q-Learning. Mining and processing capacities, as well as economic parameters and metallurgical constraints, are incorporated as the reinforcement learning environment rules. The method is validated on a real deposit, providing insights for future applications.

Jun 25, 2023

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION The two unit operations in cut-and-fill stoping that would benefit most from increased mechanization are drilling blastholes and moving broken ore to the ore¬passes. Drilling in current practice is done with hand¬held jackleg and stoper drills. Broken ore is commonly moved from the face to the orepass by a small slusher. This type of equipment can be easily moved through the raises. Hand-held drills have a slow drilling rate and require one operator for each machine. Drilling can be done much faster by small jumbo-mounted machines as two or more drills can be operated by one miner. Load-haul-dump (LHD) units move broken ore from the face to one or more orepasses at a much faster rate with less loss and dilution than slushers. These units are mobile and may be used at more than one place during a shift. The problem which must be overcome in applying this higher degree of mechanization is the restricted means of access inherent in current practices. Cut-and¬fill methods are usually applied to mining veins that are narrow, irregular in dip and strike, or where ground con¬ditions require the support of sand fill. The mechanized equipment which is needed to accomplish high produc¬tion cannot be raised or lowered through raises without being disassembled. A jumbo which will give the desired performance would be mounted on a rubber-tired carriage with a diesel engine for propulsion. Twin hydraulic booms run by a small air motor would carry pneumatic drills. Over¬all dimensions of the unit would be about 8 m (26 ft) in length, 1.6 m (5&apos;/z ft) in width, and 1.6 m (5&apos;/z ft) in height. An LHD of the desired capacity would be rubber¬tired and either diesel or electric-powered. The overall dimensions of a 2.3-m (3-cu yd) unit will be about 8 m (26 ft) in length, 1.8 m (6 ft) in width, and 1.5 m (5 ft) in height. It will weigh about 12 700 kg (28,000 1b). It can readily be seen that conventional raises can¬not handle this size equipment. The most desirable means of access enables equipment to be driven into the stoping areas. Ramps can enter the stope by being driven upward in the vein walls or by being developed in the vein on top of the fill as the stope advances. This ramp system not only permits the use of rubber-tired equipment in multiple working places but also enables its removal for repairs without component breakdown. In the proposed method, as in conventional cut-and¬fill stoping, sand fill will replace the mined-out ore. By constructing an inclined timber floor at one end of the stope, a ramp can be maintained on top of the fill and advanced as the stope is advanced cut by cut (Fig. 1). The ramp is, therefore, developed during the stoping process and is only driven as a tunnel when rising over and around the sill and crown pillars. A stoping section consists of three blocks of different geometric shapes. The first and last blocks to be mined will be triangular in the plane of the vein, and the blocks between will have the shape of parallelograms (Fig. 1). The first block will develop the initial ramp by breast stoping and filling to the ramp floor (Fig. 2). The ramp will need to be completed through to the next level be¬fore stoping of the subsequent block can begin. The subsequent blocks are mined by back stoping with the next ramp being developed at the other end of that block (Fig. 3). The length of each subsequent block can be varied without changing the slope of the ramp. As the new ramp is developed, the previous ramp is filled along with the stope cut. Access up and down is maintained through the stope. The final block is again breast stoped as no new ramp will be developed at the end line for jumbo egress. Boreholes provide ventilation between levels as well as utility access. They can also provide a secondary escapeway for personnel during periods of development. These boreholes would be located about 3 to 4.5 m (10 to 15 ft) in the footwall and spaced about 183 m (600 ft) apart along the vein. The orepasses are spaced about 61 m (200 ft) apart in the vein. This spacing allows not only a short tram for the LHD unit but also provides surge capacity for the ore between haulage trains. These passes are raised from the haulage levels. As development progresses, the raises are driven through the sill pillar, and then car¬ried in the fill as stoping progresses. Ventilation and utilities can be maintained through an orepass when it is not needed for ore. The end line orepasses are intended for this purpose as well as for personnel emergency egress. Overall dimensions and criteria assumed to illustrate the ramp method of access in a highly mechanized cut¬and-fill stope are: haulage level spacing of 61 m (200 ft); ramp gradient of 17%; average dip of approximately 1.57 rad (90°); initial stope length of 358 m (1177 ft); subsequent stope length of 179 m (588 ft); average stoping width of 3 m (10 ft) ; sill pillar thickness of 3.6 m (12 ft); crown pillar thickness of 1.8 m (6 ft); bored raises of 1.5-m (5-ft) diam; and cribbed orepasses of 1.2 x 1.2 m (4 x 4 ft) through the sill pillar and 1.2 m (4 ft) square inside the cribbed portion. DEVELOPMENT The ramp access system lends itself well to conduct¬ing the several phases of development concurrently. Haulage Drifts and Raises The first development step will be to drive the 3 x 3-m (10 x 10-ft) haulage drifts above and below

Jan 1, 1982

By Howard E. Kremers

Although more than 100 thorium-rare earth minerals are known, only a few have any commercial significance. Monazite, thorite, bastnasite, and some exotic thorium rare earth ores are reviewed Commercial interest is presently centered on monazite from the Union of South Africa, and thorite from this country. Thorium became commercially important with the development of the incandescent gas mantle about 75 years ago, Gas mantles consist of thorium oxide with small amounts of cerium oxide. The thorium nitrate used to make gas mantles was first obtained from rare thorium minerals, As a matter of fact, this use of thorium is still important and is one of the largest commercial uses for thorium materials. The discovery of monazite sand placer deposits along the coasts of Travancore, India, and in some Brazilian beach s .s, and the development of the old North and South Carolina monazite stream placers gave the mantle industry of 30 to 40 years ago a comfortable inventory of thorium ore. Even today, the thorium industry depends largely upon monazite ores for its source of thorium. This paper will briefly describe some of the major thorium ores and their principal deposits insofar as they relate to the thorium industry in this country. Because of similar chemical and physical properties, thorium always occurs with the rare earth elements and with varying amounts of yttrium. Thorium may predominate over rare earths, as in thorite-type minerals, or may represent only a fraction of the rare earth content. Typical ratios of thorium to rare earths in various minerals are given in Table 1, The average thorium content of the earth&apos;s crust is about 12 grams per ton, and in this respect thorium approximates lead, molybdenum, and some of the rare earths in abundance. The ore minerals of greatest importance to the-thorium-rare earth industry are monazite, thorite-type minerals, bastnasite-type- ores, and the family of minerals which is characterized by a preponderance of the heavy rare earths and yttrium. The latter classification includes xenotime, gadolinite, samarskite, euxenite, etc, The first two, monazite and thorite, are of greatest significance.

Jan 1, 1958

By P. Massacci

The modelling of phenomena by nonlinear dynamic Systems Theory representations require the specification and identification of suitable models of the phenomenon and the availability of good optimization algorithms to determine the optimal controls. Stochastic disturbances and difficulties of monitoring the process lead invariably, otherwise, to suboptimal performance. It will be shown that an algorithm can be formulated which will simultaneously identify and optimize such a system. The properties of the algorithm will be derived and its convergence to an optimal control proved. Some results of actual applications will be presented and it will be shown how this approach generalizes easily to optimal control of the actual processing system. These results generalize those of optimal learning and input conditioning.

Jan 1, 1991

By P. Zhang

Previous studies have shown that separation of clay minerals from non-clay minerals is the key to economic recovery of the phosphate from the waste phosphatic clays (slime) which represent about 20- 300/0 of the phosphate mined. Small hydrocyclones of different sizes (4" and 6") were tested for sizing the slime at +10 microns in order to remove most of the clay minerals. The effect of design variables and operating parameters were evaluated. Multi-stage cycloning and the effect of dispersant were also investigated. Chemical and mineralogical analyses of different size fractions of both the underflow and overflow samples indicated satisfactorily separation efficiency.

Jan 1, 1998