Search Documents

By D. Bahrami, W. K. Asante, G. L. Danko

It is prudent to interpret atmospheric monitoring signals in real time for checking the safe limits of the air conditions in underground mines. In gassy mines, real-time evaluation increases the safety of operations. In all mines, continuous monitoring and evaluation contributes to maintaining air conditions within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase in hazardous contaminant concentrations can be predicted by signal pattern recognition, root cause analysis of rapid changes toward deterioration, and forward prediction in time using algorithms and numerical models. The paper describes an early warning system for analyzing monitored signal patterns continuously in real time as well as forward predicting the various environmental and working conditions to recognize dangerous trends that may affect safety and health in underground mines. A dynamic, numerical ventilation model with heat and gas contaminant simulation components is used for the analysis of atmospheric data. Methods and test results are discussed with numerical examples for signal propagation prediction. Several mine examples are studied using controlled, synthetic data for malfunction simulations to evaluate time delays between the detection time of suspicious signal trends and the time of dangerous threshold crossing marking an accident scenario. Delay time is found in the order of 20 min in the examples, signifying the useful time period for preventive intervention between EWS warning and the likely breakout of a following accident.

By J. Smolensky, M. Paul

The Nordhalde is a waste rock pile resulting from uranium mining near Ronneburg, Germany. The pile contains over 27 million m3 of waste rock. Typical seepage water has a pH of 2.7 and a sulfate concentration of 10,000 mg/L. Geochemical investigations of the Nordhalde from 1993 to 1996 included drillholes, test pits, ABA and metals analyses, column tests, and a detailed review of the construction history of the pile. In 1996, eight drillholes were instrumented for monitoring oxygen and temperature. Monitoring continued for a fill year. Hourly temperature and pressure readings were taken by automated data recorder. Oxygen concentrations were measured three times per week, and periodic gas samples were obtained for complete analysis. The resulting data set is believed to be one of the most comprehensive of its kind. Effects noted elsewhere, such as thermal convection, are evident. However, unlike other data in the literature, the NordhaIde data shows a strong seasonal effect, with convection dominating oxygen transport only in the winter months. Analysis of the data allowed the amount of contaminants associated with ongoing and historical oxidation to be compared, and results were used to assess the potential effectiveness of proposed remediation measures.

Jan 1, 2000

By W. J. Roberds

A formal and explicit yet cost-effective approach is proposed to ensure that decisions made during mine development are optimum (with respect to their ultimate consequences) as well as defensible. This risk management approach is based on probabilistic risk assessment and established decision analysis techniques, and appropriately considers the relationships among various mine development decisions, tradeoffs among consequences, the uncertainty in predicting consequences, and the benefits of flexibility to respond to changed conditions.

Jan 1, 1992

By Jacob Bouke, Jason Janisch, Erik Vlot

The use of conventional tailings deposition methods has been the standard for decades. With the need to reduce the impact of mining, alternative methods are considered when expanding or upgrading tailings handling systems. Converting an existing tailings management system to a more sustainable deposition method during the operation of a mine may incur considerable operational and financial risk, and when assessed more traditionally, does not provide significant advantages. As a result, most mines choose to continue their current technology and add an additional pumping stage or pumpstation to their tailings line in case of a pipeline extension or Tailings Storage Facility (TSF) expansion. This also often involves raising embankments. Changing pumping technology is traditionally assessed by comparing the energy efficiency of current and prospective pumping technology. Despite a reduction in absorbed power, this traditional assessment does not include possible savings in water and the carbon footprint. With the consideration of all these three aspects, alternative pump technologies, such as Positive Displacement (PD) technology, become more economically feasible, providing increased sustainability and enable a site to future-proof their operations. Project feasibility may be affected by the high capital investment required for PD pumps. The benefit of applying PD pumping technology could be enhanced by reducing the volumetric throughput of the pipeline by dewatering the tailings to 65% solids concentration by weight. It was found that despite increasing capital expenditure, the improved reclamation of water will have a positive effect on the direct and indirect cost of fresh water intake to mine operations. This paper seeks to illustrate that in many applications the long-term benefits of investing in sustainable tailings management are optimized when more efficient PD pumping technology is combined with tailings dewatering when upgrading or expanding the tailings handling system.

Feb 1, 2024

By Siegfried Zell

INTRODUCTION Denmark is a small country with a population of about 5.5 million in the north of Europe. A substantial part of Denmark consists of islands, and the Danes have been familiar with ferry links between their islands for ages. However, their wish for fixed links has resulted in the con¬struction of bridges between most of Denmark's islands in this century. (Fig. 1) A fixed link across the Store Belt or Great Belt, Denmark's most important waterway bet¬ween the island of Fyn and main island of Sjaelland, on which the capital of Copenhagen is situated, has remained to be constructed hitherto. In 1987, the Danish government decided that the Great Belt should be crossed by a fixed link, incorporating a two-track railway line and four-lane motorway. The Storebaelt Forbindelsen AS, a joint stock company in the sole ownership of the Dan¬ish state, has been established for the purpose of planning, constructing and operating the Great Belt Link. The company will refinance the construction project by charging toll to the motorway users and fees to the state railway. Here it should be mentioned that Denmark and Sweden are about to jointly realize the fixed rail and road link across the Øresund or The Sound between Denmark and Sweden on the basis of the realization model of the Great Belt link. At present, the project is at the com¬petitive tendering or contract awarding stage. In the near future, also the third fixed link of comparable extent, that is the crossing of the Fehmarn Belt between Denmark and Germany, will go into the decisive projecting stage prob¬ably in conformity with the aforementioned pattern. Going back to the Great Belt, it should be noted that this fixed link involves three exten¬sive sections and has been under construction since December 1988.

Jan 1, 1995

By C. Stacy

The mining industry is changing rapidly. Competition among OEM and aftermarket vendors increases dramatically each year as a result of mergers and acquisitions, and especially technology advancements in the mining industry. Adding value to mine operations by delivering technical value and differentiation is becoming more subtle and more difficult to accomplish. Because of this, identifying and protecting intellectual property has become more important to the product development, engineering and marketing/sales continuum than it had been in the past. How companies protect intellectual property and determine the value of those assets is critical to the sustainability and differentiation of technology providers in the mining industry.

Jan 1, 2012

By P. Lopez, E. Wellman, N. Risso, A. Anani

Current machine learning models used for roof fall hazard prediction are mounted on expensive sensors, computationally expensive, or lack the robustness for accurate prediction in the underground mining environment. This research aims to provide a design methodology for a robust, low-cost, deep learning-based algorithm for underground mine roof fall hazard prediction. A data sampling plan is developed to ensure the replicability and robustness of the developed model. In addition, feature engineering and transformation methods are described to identify relevant features for hazard identification. The methodology described here will be used in model development, tested, and implemented as a real-time mobile device application. The new tool will be expected to detect roof fall hazards in real-time and contribute to a crowdsourcing approach for underground hazard detection.

Feb 1, 2023

By D. W. Park

Artificial intelligence has emerged over the past two decades as an important problem-solving tool including techniques such as expert systems, neural networks, tree classification, fuzzy logic, genetic algorithms, etc. These methods can be employed to solve rock mechanics and ground control problems associated with the highly complex nature of rock masses and ground conditions. A current study at the University of Alabama focuses on development of an artificial intelligence system for real-time interpretation of the data collected from longwall monitoring stations, and development of an early warning system for prediction of undesired conditions and prevention of longwall-mine instability problems. This paper describes a ground control management system using UALSAS (The University of Alabama Longwall Stability Analysis System), which is being developed to facilitate maintenance, on-line analysis, prediction, and includes an early warning system. A detailed framework of computer algorithms and their applications are also discussed. The successful application of these artificial intelligence techniques will contribute to a safer and healthier mining environment.

Jan 1, 1995

By Victor L. Steven

10.1-SHAFT SINKING AND RAISING BY CONVENTIONAL METHODS VICTOR L. STEVEN 10.1.1-SHAFT SELECTION A great deal of thought and planning should go into the selection of a mine shaft to provide the most effective use over the greatest, period of time. It sometimes is better to make an additional capital expenditure in the initial shaft program to achieve the greatest overall shaft usage. It is possible to sink a shaft which could be used for mine development, and initial production and later convert it to a ventilation, service or escape shaft. It is important to consider a second shaft in the original planning to provide ventilation, an escapeway and services for overall efficient production and safety. A second shaft usually is required to comply with state and federal mining laws. The main items to consider in shaft selection are: 1. Installation from surface or underground. 2. Vertical or inclined (sec Sec. 10.1.4L for discussion of factors involved in choice). 3. Tonnage to be hoisted. 4. Size of mining equipment to be lowered through the shaft to the underground workings. 5. Amount of water to be handled in the mining operation. 6. Ventilation requirements. 7. Type of ground the shaft is to be sunk through. 8. Position of shaft with relation to ore body. After the main features of a shaft arc determined, such as vertical or inclined, shape, size, type of lining and support, compartments, and shaft. facilities (air, water, ventilation, pump lines, power cahles, etc.), then :I sinking plant and procedures should be planned. At this point it should be decided whether the company will sink the shaft with its own crews or award the job to a competent shaft contractor. Company sinking generally will cost less if competent shaft men are available. Money also will be saved in plant costs, such as for hoist, headframe, compressed air, buildings, etc., as these will be part of the permanent plant and can be used in the sinking operation. Labor costs generally will be lower than contractor construction rates. The advantage of having a contract, or is the speed of completion of the project. Contractors usually have headframes and hoists ready to move on the job immediately and have trained crews ready to complete the project in the shortest possible time. Next, the type of surface sinking plant (hoist, headframe, etc.) should be selected and a determination made whether it is to be temporary or permanent. In most cases it is less expensive to install the permanent, headframe and hoist, and use them for sinking. The type of actual sinking equipment to be used should be evaluated for the most efficient sinking cycle, e.g., mucking method, drilling method, and lining or support means. The proper cycling of drilling, mucking and lining is extremely important in obtaining the most favourable sinking costs. 10.1.2 - GROUND STABILIZATION AND WATER CONTROL Prior to the shaft-sinking operation an investigation should be made into ground-water conditions. If water is anticipated, then pregrouting of the ground

Jan 1, 1973

By David Oliveira

"INTRODUCTIONOne of the key drivers for the selection of a mechanized tunneling method in good quality rock masses is a good excavation advance rate. In order to achieve satisfactory advance rates, a good geotechnical performance of the rock grippers in main beam open tunnel boring machines (TBM) is required, besides other factors related to ground support and the performance of the cutter head.One well known potential issue of main beam gripper TBM is associated with the bearing capacity of the tunnel side walls while crossing fault zones or poor rock masses in general. Such a mechanism is similar to that of footings on rock and perhaps the most common problem associated with gripper performance. Depending on the quality of the rock, the rock under the gripper contact may experience significant damage and crushing (Figure 1), eventually affecting the TBM advance rate due to a lack of tunnel wall reaction/support. Such a mechanism is primarily dependent on rock quality, applied loads and gripper size.In the case of large diameter TBMs (e.g., D > 12 m), a second potential failure mechanism may arise associated with the loss of confinement within a rock pillar between twin tunnels, even in good quality rock but particularly in bedded sedimentary strata. Punching of the rock pillar may develop due to excessive shear along bedding partings and sub-vertical joints (Figure 2), particularly under a low stress environment. As a result, this mechanism is dependent on both the rock pillar width between twin tunnels and stress conditions around the tunnels, in addition to the previous factors described for the first failure mechanism."

Jan 1, 2016

By A. A. Schweizer

This paper documents the growth and projects the future of Green Diamond Sand Products. Since1954, Green Diamond, located in Riddle, Oregon, has been producing sand from granulated nickel slag for use in various markets. Through the years, the company has seen several changes from its ownership to its product lines. In 1991, Green Diamond was producing abrasive sand at a rate of about 30,000 tons per year. It was at this time that Green Diamond became part of Glenbrook Nickel Company. Over the next eight years, Green Diamond would quadruple its production to over 140,000 tons while moving into three new markets, as well. Green Diamond is now producing sand for use in the abrasive, foundry, construction, and roofing industries. In 1998, Green Diamond again found itself under new, private ownership. With plans on developing agricultural sand and spent abrasives recycling, the future of Green Diamond appears to be one of further expansion coupled with diversification of its product lines.

Jan 1, 2000

By T. Lamond, J. O. Costello

Marble is a preferred surfacing material in up-scale buildings. Its use increased in the 1870's with rising national wealth and declined in the 1950's when synthetic materials for these applications were developed. Natural marble is now limited to high-end domestic and commercial structures. Cultured marble is a paste of white marble dust and polyester resin cured in molds yielding fixtures of specific finished dimensions. Dyes incorporated at different stages in the mixing cycle mimic shades and veining of natural marble. This paper discusses the filler requirements for cultured marble production and reviews new techniques to cut and finish natural marble.

Jan 1, 1999

By G. A. Johnson

Basic management principles will be discussed (as they apply to minerals education efforts), especially in light of the changing nature of volunteerism in today’s society. Also, the “minerals education tree” will be presented, along with public opinion / public policy realities.

Jan 1, 2001

By James A. Finch

The Gaudin lecture is devoted to fundamentals. Given my involvement with column flotation over the last 20 years, this is my topic. I have tried to identify spinoff basic research and provide a personal list of favorites. Two are selected for discussion here. They are single bubble rise and bubble surface area flux. The rationale for such work, as well as some of the findings, are reviewed. Support for fundamental work seems as volatile as the economy (and the link is probably not coincidental). I hope some utility to the minerals industry is evident in the text. Column flotation in its current form originated in the early 1960s. The method was invented by Boutin, patented by Boutin and Tremblay and pursued doggedly by Wheeler. Their aim was to overcome the problem of mechanical entrainment of fine particles in the water carried by the bubbles, which they were convinced contributed to lowering flotation concentrate grades (Wheeler, 1988; Finch and Dobby, 1990). The solution was a combination of columnar geometry, the addition of wash water into a deep froth and the maintenance of an excess of water to the tailings, as compared to the feed (a so-called positive bias). Success at Les Mines Gaspe, Quebec, on cleaning Mo in the early 1980s signaled the start of industrial acceptance, making the column one of the flotation machines of choice today. Over the next 20 years, column applications mushroomed to cover virtually all mineral commodities, as well as nonmineral applications such as soil decontamination, deoiling of water and deinking of recycled paper. In the wake, research groups are continuing to probe the fundamentals, conferences and workshops have been transferring the technology and specialist companies have emerged to service the demand. Innovations were triggered as problems arose (for instance, in gas injection systems) and novel flotation cells, much in vogue in the 1990s, had the door opened. Mechanical cell manufacturers have not been idle - there is nothing like competition to provoke a fresh look at an established business. Flotation-cell technology has probably not seen so much activity since the patent rush in the early days of flotation, which occurred around the turn of the century. For an industry often considered reluctant to risk innovation, this is not a bad record. A good idea will find a place, but patience (not always an innovators strong suit) and careful preparation are required. Two books (Finch and Dobby, 1990; Rubenstein, 1996), three symposia (Sastry, 1988; Agar and Huls, 1991; Gomez and Finch, 1996), and a series of reviews (Dobby and Finch, 1991; Finch and Dobby, 1991; Finch, 1995; Finch et al., 1995) document the period. Like many good ideas, column flotation has been overexposed, and there have been disappointments. In a recent example, columns performing scavenging duty were replaced by mechanical cells (Chong et al., 1998). The further applications stray from the original - to

Jan 1, 1999

By M. Visnjic

Open Pit Mine Production scheduling under commodity price uncertainty suffers from an exponentially increasing problem size as simulations and real options flexibility are used to generate and evaluate multiple production schedules. Robustness evaluation techniques attempt to evaluate a production schedule that is generated on a single set of economic parameters against several varying prices and sources of uncertainty. This approach is invalid as the corresponding optimal LOM mine plan will change for each set of evaluation parameters. Using commodity market futures and treasury bonds as production schedule economic input parameters provides fully price and time-value-of-money risked scheduling parameters that maintain a deterministic problem size. This paper will provide comparative analysis of project NPV’s coming from traditional price uncertainty evaluation based on a single fixed LOM mine plan using varying prices versus evaluation based on varying LOM plans that are both generated and evaluated using varying prices. When cross evaluating constant price mine plans against simulations, the upside potential and downside risk of a project are significantly misrepresented. INTRODUCTION The life of mine (LOM) production scheduling problem seeks to answer the question of from where and when to extract a given block within the ultimate pit limit as well as where and when to process it. Solving this problem takes into account the constraints of extracting any particular block while seeking to maximize the net present value (NPV) of the mineral asset as a whole. A direct driver of the value of a block, and there for the entire asset, is the market price of the commodity in question. Complications arise when an optimal production schedule is attempted to be solved under price uncertainty. Many solution methodologies have been proposed in an attempt to optimize under this criterion, yet there are three salient aspects that are overlooked during this process. They are: • Generating a single production schedule and evaluating it against many simulated price paths. • Failing to understand the mechanism describing particular commodity price behavior • Inappropriate risk adjustment In an effort to address these aspects of production scheduling under commodity price uncertainty, we propose a methodology to define the economic parameters as input that is applicable to most if not all production scheduling approaches. This methodology will not only simplify the production scheduling process in terms of establishing block value but utilizes the risk adjustment of real options valuation to avoid the arbitrary blanket risk adjustment of traditional discounted cash flow valuation. Our findings conclude that attempting to optimize around individual price paths is futile and using a market risk adjusted single price forecast provides a justified economic basis for production scheduling while maintaining the same problem size as a deterministic production scheduling problem.

Jan 1, 2019

By R. W. M. Lai

In flotation or hydrometallurgical leaching of minerals, the cumulative metals recovery for a given process condition generally approaches a maximum value or an asymptote as the process time increases. This paper discusses the experimental methods of identifying and obtaining the asymptote of metals recovery through kinetic studies. In flotation, the kinetic asymptote of metal recovery, or ultimate recovery, is a function of grinding and collector dosage, but within a realistic variable range, is not a function of pH or temperature. However, variations in grinding, collector dosage, pH and temperature, all exert noticeable effects on flotation kinetics. Frothers generally have a minor affect on the asymptote, but have a major affect on flotation kinetics. The asymptote from batch flotation is found to be identical to that of a continuous flotation. In hydrometallurgical Leaching, the asymptote of metal recovery for a given leaching system is a function of such variables as temperature, particle size, and acid concentration.

Jan 1, 1983

By I. Weir-Jones

[Currently the cost of carrying out 'in situ' geotechnical investigation programmes or installing and operating monitoring systems at construction or mining sites is rising var." rapidly. This is primarily because of our ever increasing labour rates. As a result of this problem efforts are no,, being made develop techniques for the economical; collection of large quantities of geotechnical data relating, to such problems as done stability evaluation, the behaviour of underground openings, or 'in situ' testing procedures. The efforts to reduce the labour content. are particularly apparent in those procedures which have traditionally been manpower intensive e.g. 'in situ' permeability testing where an entire drilling crew and their associated eguipment have been on standby while testis has been carried out; or data collection in underground construction operations where much tine is typically wasted obtaining or maintaining access to instrument sites. In an attempt to illustrate one specialist consulting company's approach to the problem of reducing investigation costs, this rarer examines four recent developments in the field of geotechnical investigation and monitoring which have come about during the last two Years as a result of cur research and development programme. Although these techniques and devices have been developed for specific projects, they all have broad applications in the geotechnical field and they are indicative of the direction in which this company feels developments will take place.]

Jan 1, 1975

By Jr. Koch

Since 1882, world zinc production has increased. In contrast, United States zinc production rose until about 1915, but since then has remained nearly constant, with a slight tendency to decrease. Production from the Tri-State district, the largest early source of zinc in the United States, has gone down steadily; this decline has been balanced by a growth in the rate of other districts. These changes in United States production are due to economic, not geological, factors. Recent exploration has located large mineable ore bodies; additional deposits will undoubtedly be found in the strata-bound carbonate rock and volcanogenic environments. A statistical analysis of the exploration effort in the Middle Tennessee district indicates that new discoveries can be expected there. Thus, the United States is in an early stage of the production cycle for zinc. Of major mining districts in the United States, only the Tri-State is exhausted under current economic conditions; large zinc resources of low-grade material, which would repay mining at higher prices or improved technology, are known to exist in that district.

Jan 1, 1980

By L. S. McNickle

[Commonly accepted maintenance methods are being outdated by the rapid acceptance and use of more complicated hydraulic circuitry on modern mining equipment. It is no longer adequate to use the maintenance program to merely repair or sustain equipment operation. Ever increasing operating costs place a huge premium on lost production time. It has, therefore, placed the maintenance programs in the position of being required to alleviate equipment malfunctions on production shifts and still attain the maximum unit life from each component part.]

Jan 1, 1961

By E. F. Paski

Geological materials are likely the most complex and challenging substances to quantitate by ICPOES (inductively coupled plasma optical emission spectroscopy). For complex materials having widely varying compositions, spectral overlap interferences govern detection and quantitation limits attained by ICPOES based analytical methods.

Jan 1, 1993