Search Documents

By A. J. MacKellar

The economic viability of any project is generally assessed on an evaluation of the total capital constructed costs along with operating costs, owner's costs and market conditions. This paper will be directed to the role that Cost Engineering plays in the development of the capital costs and the cost control techniques applied thereto.

Jan 1, 1975

By Kevin Vander Tuig, Tim O’Rourke, Rick Vincent, Doug Lopata, Kellie Rotunno, Dan Dobbels

"The Northeast Ohio Regional Sewer District (NEORSD) was required under the Federal Clean Water Act and U.S. Environmental Protection Agency’s (U.S. EPA) Combined Sewer Overflow (CSO) Control Policy to develop a Long Term Control Plan (LTCP) to reduce or eliminate overflows from its permitted CSO outfalls. The LTCP was completed in 2002. Key components of the plan include: 26 miles (42 km) of deep storage and conveyance tunnels providing a total CSO storage volume of 325 million gallons (MG) (1.2 billion liters); over 30 miles (48 km) of consolidation sewers to route CSO control flows to the tunnels; and associated diversion/inflow control structures and drop shafts. Final design and construction of the initial phases of the LTCP are completed or underway. Advanced planning of the final phases began in April 2013. This paper summarizes this advanced planning process and, specifically, how hydraulic performance and tunnel design and construction considerations were balanced to eliminate unnecessary projects and shafts, reduce implementation risks, and reduce program costs by approximately $650 million. BACKGROUND The Northeast Ohio Regional Sewer District (District) serves an area of approximately 350 square miles (SM) (907 km2), including combined (81 SM; [210 km2]) and separate (269 SM [697 km2]) sewer systems that discharge to three wastewater treatment plants in the greater Cleveland area. The service area, shown in Figure 1, is divided into three districts—Easterly, Westerly, and Southerly—each having its own interceptor system and treatment plant, ranging in wet weather treatment capacities from 100 to 735 million gallons per day (MGD) (378.5 million to 2.8 billion L/day). The system includes 124 permitted combined sewer overflow (CSO) outfalls overflowing into the region’s tributary streams, Cuyahoga River, and Lake Erie."

Jan 1, 2016

By Todd Kilduff, James Grillo, Shrey Arora

In efforts to improve ingress/egress from the existing subway platforms in PATH’s Exchange Place Station, a new 18-foot horseshoe cross-passage tunnel was constructed by Walsh Construction who retained Kilduff Underground Engineering for design of the initial support system and to install and maintain geotechnical instrumentation. The project presented some unique challenges as a result of the proximity to pedestrians on the platform. PATH service remained uninterrupted, limiting the Contractor to mechanical means of excavation to advance the heading. The logistics proved very challenging for the approximate 100-foot-long tunnel excavated in soft Manhattan Schist. This paper will present the design and construction challenges for the project.

Dec 1, 2022

By Michael Hood

Subsidence profiles above two adjacent panels in Illinois are compared with pro- files predicting subsidence behavior obtained using the (i) National Coal Board (NCB, 1975) method, (ii) the profile function method and (iii) the influence function method. The NCB method predicts the maximum subsidence values at the center of the troughs accurately, but, the overall shapes of these predicted profiles do not match the profiles from the measured data well. Consistent values for the angles of draw were measured but these angles were different in the transverse (average value 43 degrees) and in the longitudinal (average value 17.5 degrees) directions. Time dependent subsidence effects are shown to be small but measurable. These displacements continue at a linear rate for at least a 12 month period. A comparison of measured horizontal distances, interpreted as horizontal strain, and the NCB predictions for strain shows that the peak measured strains are greater by a factor f about four than the predicted strains. The relationship between surface curvature and strain is investigated. Problems associated with calculation of surface curvatures from vertical displacement data are highlighted and a recommendation is made for future studies to consider direct measurement of this parameter. Surface curvatures above a moving face are found to be about three times less than the curvatures at the stationary end of the panel. On the other hand, a hyperbolic tangent profile function is shown to serve as an accurate predictive tool for subsidence behavior in two adjacent longwall panels at Old Ben Number 24 mine in Illinois. This function predicts not only the vertical displacements but also the surface curvatures above both panels. Influence functions are shown to be more problematic, although potentially more flexible, in their application than the profile functions.

Jan 1, 1982

By C. B. Henderson

The development of slurries of coal and water as a boiler fuel replacing No. 6 fuel oil has been actively pursued at the Atlantic Research Corporation since 1976. Funding for this effort has been provided by the U.S. Department of Energy, the Electric Power Research Institute, and by corporate funds. The name ARC-COALTM has been selected for these slurries. Stable coal-water slurries with bone-dry coal loadings between 62% and 77% have been prepared, evaluated rheologically, and successfully burned in an experimental furnace without the assistance of other fuels. The advantages and properties of these slurries, including combustion results, are reviewed. Also discussed is the pilot line used for processing barrel quantities of fuel and a pilot plant capable of processing 600 bbl/day, currently being designed.

Jan 1, 1982

By Gary P. Thomason

We have all heard a great deal about how various projects were financed or certain companies were successful in obtaining a bank loan. There are many more projects and companies who fail to get the money they need. At least a portion of these failures, and a large percentage of the frustrations connected with even the successful financings, are a result of not understanding the process of obtaining money. Recent years have seen a proliferation of sources available to finance minerals operations, but let me assure you that these represent only a minor portion of the minerals financing market. The fundamental source of borrowed money to almost all minerals related companies remains the banks. Therefore, understanding the "Loan Approval Process" can easily mean the difference between getting the money or not. In the following pages I hope to provide some insight into what I define as the loan approval process. Having pre-offered my definition, I intend to delineate the various stages of the process and the planning and information I believe should be contained in each. My ultimate goal is to help you think like a banker and, in so doing, stay on top of the process so that you can successfully obtain the funding necessary for your projects.

Jan 1, 1983

By Wi11iam I. Rau

In the recent past, there have been numerous projections of the capital requirements for additional mine and processing capacities required to meet projected non-Communist World demand for minerals during the next 15 years. A consensus judgment would place this currently at $14 billion per year, with the largest expenditures required for increases in aluminum and copper production. Until the early 1960's, internally-generated funds were used to finance nearly all of the large mining companies' capital requirements. Since that time, however, the enormous rise in capital costs per ton of capacity, accompanied by a relative stagnation in the financial condition of many of the major mining companies, have caused the industry to begin to rely on external sources for financing expansion, most notably, project financing from commercial banks and institutional lenders. Seven years ago, it was estimated that, in the five-year period 1972-1976,75% of the total capital requirements of $10 billion per year would come from internally-generated funds, with the balance to be provided by external sources. l There is little doubt that, in the coming decade, the percentage provided by external sources will increase. There should be little difficulty in attracting the necessary investment within the U.S., particularly in view of the expected continuation of companies in diverse industries seeking mineral investment opportunities. The more serious question lies in the availability of internal and external sources of funds for the expansion of mine and smelting capacity in the developing countries. Recently, R. F. Mikesell projected an average annual investment of $4.7 billion (in 1977 prices) over the 1977-1990 period would be required from foreign sources to expand metal producing capacity in developing countries. Mikesell concluded that external financing of mining projects in the developing world has averaged less than $1 billion per year over the past five years, thereby requiring more than a quadru1ling of this financing over the next decade.

Jan 1, 1978

By S. Frisch

Selenium (Se) in effluent waters has become a significant challenge for a number of industries. Toxicity studies and new reports of occurrence have certainly caused increased scrutiny and actions in the mining industry today (Sandy, DiSante, 2010). While initial activity in addressing selenium-laden waters were conducted in the coal mining industry, today a much broader range of mine types are beginning to search for solutions to selenium treatment of their mining waters, including both hard rock mining operations (gold, nickel, zinc, etc.) and soft rock mining (phosphate, uranium, etc.) Throughout North America, new regulations covering selenium discharge are either in place or being developed. While a number of physical/chemical approaches show promise in selenium treatment, when considering optimal cost and treatment efficacy issues, biological treatment ? particularly fixed-film biological treatment - is reported to be one of the most promising approaches to managing selenium-containing waters. Among biological treatment options, the fluidized bed reactor (FBR) has undergone extensive pilot testing for Se treatment in the last three years, including eight pilot programs, and the first FBR system is now operating at a coal mining site. In all tests, the FBR has been shown to be a highly cost-effective approach to selenium treatment based on its physical and performance characteristics. This is consistent with its history for reaching low levels of treatment in similar service for other oxyanions including perchlorate, nitrate and various metals. With the results from the most recent testing, the technology has been shown to be adaptable to an ever-broadening range of influent water conditions and flow rates, in varying terrains and weather conditions. Selenium occurs in various valence states from -2 to +6 (Sobolewski, 2005). The speciation of selenium plays a critical role in understanding the effectiveness of any approach for removal, especially to low levels. Elemental selenium is insoluble and has little effect on living organisms. Colloidal fractions are known to occur. In aqueous environments such as coal mining runoff, selenium is most often found as the oxygenated anions of selenite (SeO32-, Se4+) and selenate, (SeO42-, Se6+). Selenium is commonly found in mining waters in concentrations ranging from 3 to >12,000 µg/L. The U.S. National Primary Drinking Water Standard MCL is 50 µg/L for selenium (EU 10 µg/L; WHO 40 µg/L). The National Fresh Water Quality Standard is 5 µg/L for selenium. The U.S. Fish and Wildlife Service has recommended that the National Fresh Water Quality Standard be lowered to 2 µg/L to protect fish, waterfowl, and endangered aquatic species. Several states have followed with enforcement actions at these same low levels. In Canada, permits may require stakeholders to monitor levels in water or biota, or to comply with guidelines, at either the National or Provincial levels, which can be as low as 1 or 2 µg/L in surface waters. Treatment of selenium in all mining waters presents a series of challenges. It can be present in relatively dilute concentrations and in streams with variable and often high flow rates. It can be present in many soluble and particulate forms, which may affect process design and treatability. The conditions of influent selenium-containing waters can vary, with issues such as temperature, pH, total dissolved solids and other contaminants affecting the ability to remove selenium selectively and economically. Treatment of selenium often results in the generation of a concentrated by-product requiring disposal, and re-release from residuals can occur. Beyond these issues, the physical environment of a mining operation can offer challenges such as remoteness and harsh and/or cold weather. Currently available selenium treatment technology (Table 1) includes biological treatment and a number of physical-chemical processes ? such as ion exchange, membrane filtration and adsorption ? that vary widely in efficiency and cost. Most treatment options remain either too costly and/or unproven for selenium-containing streams for reasons that include poor removal efficiency, variability in volume and composition of influents, system sizing and logistics considerations, as well as operating requirements.

Feb 23, 2014

By Cristian Saavedra, Patricio Zarate

Flotation collectors play a crucial role in mineral flotation by selectively adhering to mineral surfaces and aiding in their separation from gangue material. They are heteropolar molecules, as defined by Sutherland and Wark (1955), featuring non-polar hydrocarbon chains and polar groups interacting with mineral surfaces to induce hydrophobicity selectively. The importance of collectors in mineral processing, as underscored by Lotter and Bradshaw (2010), lies in their ability to enhance recovery rates and improve selectivity, thereby optimizing the extraction of valuable minerals from complex ores. Collectors are classified based on their mechanism of action, as proposed by Laskowski (2010). This classification categorizes collectors into three groups: water-soluble compounds, water-insoluble “oily” collectors, and water-insoluble amphipathic compounds forming molecular films at the water/gas interface. This complements the chemical structure-based classification by Sutherland and Wark (1955) and Suoninen and Laajalehto (1993), offering a comprehensive understanding of collector diversity in flotation systems. Collector selection is an iterative process crucial for optimizing mineral processing efficiency, as emphasized by Lotter and Bradshaw (2010). Understanding the significance of collector mixing or synergy outcomes is paramount for enhancing mineral flotation efficiency and sustainability. Taguta, O’Connor, and McFadzean (2018) demonstrate that mixed collector systems enhance interaction enthalpies and microflotation recoveries, indicating improved performance. McFadzean, Castelyn, and O’Connor (2012), along with Critchley and Riaz (1991), delve into investigating synergistic interactions between collectors, offering insights for strategic selection. Observations from the study of collector synergy, as noted by Wakamatsu et al. (1980), reveal nuanced relationships surpassing individual collector behaviors. The methodology outlined in this paper provides valuable guidance for classifying and selecting collectors based on specific application needs, while also suggesting the potential for synergistically improving recovery across fine, intermediate, and coarse particles.

Feb 1, 2025

By M. Akram

Stability assessment of entry roofs is an essential precursor to all underground design. Both multi-seam interaction and longwall mining can subject entries to radical changes in the surrounding stress field. Such loading changes frequently produce instability and failure in the roof, floor and pillars. Roofs are shown to be vulnerable to stress-induced failures, particularly when the load is unsymmetrical. To predict the effects of changes in stress field, roof failure conditions under increasing loads were studied using finite element analysis and body loaded photoelastic models. A large range of geologic conditions were evaluated and incorporated into the model using Monte Carlo methods. Entry analysis using the model showed the roof to be particularly vulnerable to shear with the location of the failure site changing to meet loading and geologic conditions. Results were correlated with field data to determine stress levels at which failure could be expected to occur. Based on this research a roof stability model SESAME was constructed for roof stability evaluation under specified loading conditions.

Jan 1, 1993

By C. Y. Haas

Of all the industrial clay minerals, attapulgite probably enjoys the widest variety of applications. A review published over three years ago by Haden and Schwint (18) cited some 80 individual uses, a list which continues to grow. In its near half-century of commercial life, attapulgite has received a generous share of research study and patent development effort, both on the part of producers as well as consumers. This work has been divided between understanding the mineral's structure or properties and applying it to specific end-uses. Naturally, information gained from the former has pointed toward opportunities in the latter. References of particular significance are cited throughout the text. Attapulgite's variety of uses derives from the unique three-dimensional structure and needle-shaped particle form of this crystalline hydrated magnesium aluminum silicate. Its inherent colloidal and sorptive properties are well known, and distinguish it from its sister clay minerals. Attapulgite is characterized by its high surface area, porosity, sorptivity, and decolorizing power. Its slips or slurries are viscous and thixotropic, however, unlike bentonite are not flocculated by electrolytes. In Table I are compared the general properties of attapulgite, bentonite, and kaolin. The properties in Table I are documented in greater detail by the wealth of scientific literature which has been published on the composition (14)(15), structure (6)(16), surface (16)(4)(22)(24), adsorption (31)(4)(5)(25), rheology (10-11)(12)(13)(26)(27)(32), plasticity (30) (31), and chemistry (23)(3)(7) of attapulgite. Attapulgite is the principal mineral constituent (70 to 80%) of attapulgite clay as it is commercially produced in the Georgia-Florida area of the United States. As mined, this clay also contains 10 to 1S% montmorillonite, sepiolite, and other clays; 4 to 8% quartz, and 1 to 5% calcite or dolomite. (18) During processing, non-clay fractions are removed so that commercial products are enriched to 85 to 90% attapulgite. By wet processing (such as practiced in the

Jan 1, 1971

By D. R. Willmer, E. J. Haas

"DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT This study analyzed the publicly available health and safety policies of 26 mining companies to determine the quantity of health and safety (H&S) practices that mining companies encourage in relation to the Plan-Do-Check-Act cycle. A thematic content analysis of the policies identified elements and practices within the text. On average, companies communicated information on about 7 elements (range 1–14, standard deviation = 3.49) and discussed 15 practices (range 2–34, standard deviation = 9.13). The elements in which companies highlighted the most practices were risk management, emergency management, leadership development, and occupational health. A discussion of the policy trends shows areas that mine sites can improve upon within their Plan-Do-Check-Act cycle, in addition to encouraging the use of both leading and lagging indicators to manage health and safety performance. INTRODUCTION Mining companies and their employees are expected to identify and manage risks at their worksites to ensure the health and safety (H&S) of everyone at the site. The primary mechanism in place to control these risks is a company’s health and safety management system (HSMS) (Boyle, 2012). Broadly, an HSMS is a set of standard, interrelated, and interacting elements used to promote and achieve occupational H&S goals (ANSI/AIHA Z-10, 2012; BS OHSAS 18001, 2007). The practices conveyed within an HSMS are expected to minimize incidents, injuries, illnesses, and even save worker lives (Alsop and LeCouteur, 1999; Arocena and Núñez, 2010). In the United States, both the Occupational Safety and Health Administration (OSHA) and Mine Safety and Health Administration (MSHA) regulate and encourage aspects of an HSMS (US Federal Register, 2011, 2010). Many HSMS documents (i.e., Chemical Industries Association, 1995; Health and Safety Executive [HSE], 1995; International Labour Office [ILO], 2001) attribute the source of their basic management system to Deming’s Plan-Do-Check-Act (PDCA) model of continuous quality improvement and organize their practices within this cycle (Johnson, 2002). The PDCA cycle is a well-adopted approach in health and safety management and promotes continuous learning and adaptability (Robson et al., 2007)."

Jan 1, 2018

By Robert L. Major

The expanded role which coal has been assigned in the energy future of the United States has raised numerous policy questions. The very complexity of these questions makes them suitable to analysis by econometric models. However, as the Wall Street Journal indicated in its recent article, business' success with such models have been mixed. I have been asked to present my views as to how coal producers can use such models and in what ways the industry is likely to be impacted by such models. I do not presume to speak for the whole coal industry, but only to share with you the personal observations of one who has worked "both sides of the street", having been employed' both by government and a consulting firm prior to joining the coal industry. In my opinion, the use of econometric models to analyze the coal industry will impact the coal producers in two main ways. First, their use by government will have a profound impact on future government policies related to the mining, transportation and utilization of coal. Second, such models, when properly calibrated and refined, may become useful tools for the coal producers in doing market research and long-range planning. While the former has already begun to impact on the operating environment or the coal industry, the latter is still in the embryo stage.

Jan 1, 1977

By William Gleason

"The city of Denver, CO has experienced extreme growth in the past decade, with the population of the city topping more than 700,000 people in 2018. The current storm water drainage system was put in place in the early 1900s and has not been able to keep up with the growth of the city.When it rains north and east of the city, the runoff goes toward the South Platte River. With the dense population and sometimes severe thunderstorms in the summer, the city has experienced significant flooding that not only endangers lives of residents, but some of the storms have caused millions of dollars of property damage.The Platte to Park Hill Project is a $298-million nearterm, four-phase solution to the flooding that includes the Globeville landing outfall; an open drainage project in the Cole neighborhood in north Denver; an area for temporary water detention and another temporary water detention in Park Hill.The largest and most complex phase of the project is the Globeville landing outfall — a $70-million box culvert project that includes a pair of 157-m (515-ft) long, 243-cm (96-in.) diameter storm water tunnels that pass beneath a busy rail yard with 17 tracks for the Union Pacific Railroad (UPRR) and two Regional Transportation District (RTD) commuter rail tracks. The tunnels, which were installed parallel to a pair of existing 243-cm (96-in.) tunnels, were designed by Brierley & Associates as a client of Merrick & Company for the City & County of Denver, and Bradshaw Construction constructed the one-pass tunnels.From the start, it was evident that the tunneling portion of the project would be the most challenging because of the rail yards.“It’s a little bit more complicated because the railroads have such tight restrictions for settlement,” said Rebecca Brock, Brierley’s project manager. “We had a lot of meetings with Union Pacific and RTD to figure out what are prescribed versus tolerable settlements.”“The portion extending beyond the UPRR under the RTD rails was challenging, as RTD is new to tunnel installations under its tracks,” said Lester Bradshaw, president of Bradshaw Construction. “The RTD tracks employed a unique foundation of continuous concrete with integral raised concrete ties on rubber bushings. Minimizing settlement to these tracks was a critical requirement.”"

Jan 9, 2018

By Robert E. Hershey

The phosphate industry is the fourth-ranking mineral industry in Tennessee; it has an annual value of 13,000,000 and a yearly production of almost 2,000,000 tons of phosphate ore. Tennessee, at present, is second in rank of phosphate production in the United States. In accord with the importance of this mineral commodity, the Tennessee Division of Geology, is conducting a continuing study of the industry' and the raw s, materials upon which it is dependent. Of the three type's of phosphate found in Tennessee, the brown phosphate rock of the Bigby faces of the Bigby-Cannon limestone is by far the most extensive in occurrence and is the only type being mined at the present time. Because of the importance of the brown phosphate ores, our Division has mapped , in detail the outcrop pattern of the Bigby facies of the Bigby-Cannon limestone. The geologic mapping was done by Dr C. W. Wilson, Jr. and others under his super-vision and the geology plotted on 7 1/2-minute topographic maps, with scale of 1 to 24,000 or 1 inch equals 2,000 feet. These maps will be available for use in the near future and will be published later-with complete geologic coverage.

Jan 1, 1960

By T. Emery, D. Sweet, J. Bourgeois, B. Seymour, D. Porter

Cemented rockfill (CRF) is being used to backfill primary and secondary stopes at the Eagle Mine, an underground nickel and copper mine operated by Lundin Mining. National Institute for Occupational Safety and Health (NIOSH) researchers from the Spokane Mining Research Division (SMRD) are conducting cooperative research with the mine staff to determine if the size of a CRF sample affects its measured strength properties. Based on previous research by NIOSH, cylindrical samples of CRF ranging in size from six to eighteen inches in diameter were cast at the mine and cured underground. The samples were later transported to the SMRD laboratory and the Michigan Technological University where tests were conducted to determine the strength and elastic properties of the CRF. To further analyze the relationship between backfill density and compressive strength, different ASTM International compaction techniques were used to cast the samples. For comparison, tests were also conducted on in-situ core samples that were drilled from a stope which had been backfilled with the same CRF mix. The data collected from this study not only improves our understanding of CRF in-situ properties but also helps optimize Quality Assurance/Quality Control (QA/QC) methods for backfill preparation and testing.

Feb 1, 2023

By E. J. Hammer

In the crushing and grinding of metallics for beneficiation, the sizing is normally done to liberate the metals or sulphides for further processing to improve recoveries of the basic metals or minerals. The objective is to reduce the ore in size through various closely controlled stages to that degree of fineness which gives an economic liberation of valuable mineral, but which avoids as much as possible the production of sliming fractions. A different philosophy applies to the crushing and grinding of Gypsum. Our requirements normally demand controlled grinding and/or crushing of the material not only to a fineness suitable for further processing of the mineral into end products, but to produce various sizes of material which are them- selves saleable products. The majority of our tonnage ultimately ends up in stucco for Wallboard. Therefore, our mineral reduction is normally designed toward this end, but it is done in a manner that permits drawing off inter- mediate products to meet various Customer requirements. This forces us into compromises at times in our equipment installations, and our equipment must sometimes be more versatile and complex than we would like it to be. We try to process our basic rock, Gypsum, for the most efficient size reduction. We market 5 to 6 different sizes intermediate to the end product, which generally is the fineness of material to be used for stucco for Wallboard, and we do this with controlled crushing, grinding and sizing cycles of the material. To summarize, we use a different philosophy of crushing and grinding than the metallic field which uses comminution or crushing and grinding to improve recovery, whereas we choose our equipment to crush and grind primarily for product performance.

Jan 1, 1969

By R. P. Schneider

The Chino mine, concentrator, and smelter are located in Grant County in Southwestern New Mexico. Chino Mines Company is a partnership two-thirds owned and operated by Kennecott Santa Fe Corp., and one-third owned by MC Minerals Corp. (Mitsubishi) of Japan. The Chino Ore Body The Chino ore body is a widely varied deposit of rock types and contains intrusive stocks and sediments. The stocks contain chalcocite in a matrix of quartz, mica, and feldspar. Much of the feldspar is altered to clay. Some of these stocks are enriched with native copper. The sediments contain chalcopyrite associated with gangue minerals including magnetite, pyrite, garnet chlorite, and epidote. The contact of the stock and sediment is heavily altered to chlorite and clay. The stock ores contain economic quantities of molybdenite. The operating work index of Chino ore varies from 5 to 20 kwh/ton and averages 8.5 kwh/ton. The ore head to the concentrator averaged 0.81% copper and 0.010% molybdenum. Fifteen percent of the total copper head exists as nonsulfide mineralization.

Jan 1, 1985

By D. D. Runnells

In order to establish meaningful remediation goals and monitoring programs in areas disturbed by mining, it is desirable to determine the natural metals concentrations that existed in the area prior to mining. At Iron Mountain, California, several natural sources exist for acid drainage and loading of metals to Slickrock and Boulder Creeks. This paper describes methods to determine the contribution of copper and zinc to groundwater and surface water from those sources, including natural gossan rock outcrops, mineralized bedrock, and colluvial materials. Methods used include evaluation of: 1) historical information, 2) literature values of unmined, mineralized areas, 3) analyses of water from monitoring wells, 4) leaching studies, 5) statistical analysis, 6) isotopic studies, and 7) identification of background by elimination of mining sources. Results from this natural background determination show that Boulder Creek and Slickrock Creek carried elevated concentrations and loads of copper and zinc prior to mining activities. With repeated rinsing of reclaimed and remediated mine materials by rainfall, there will be a diminishing contribution from residual waste rock and tailings at Iron Mountain, and natural background will become an increasingly larger proportion of the total load.

Jan 1, 1999

By Z. Sample

"INTRODUCTION This past year commodity prices continued their dip with increased volatility causing market values to slide another 16% putting increased pressure on even the largest companies to improve their free cash flow.[1] Without a recovery in commodity prices in sight, companies must find a sustainable method to improve returns in the current economic climate. In an effort to improve plant sustainability, the mineral processing industry is investing in advanced automation technologies and innovative processing methods that are both more reliable and more efficient than ever before. One such breakthrough technology is Heap Leaching (HL). This method of extraction has certain advantages over traditional metallurgical methods making previously unsustainable operations economically feasible. While HL is already seeing use in the gold and copper industries among others, recent developments may allow for the use of HL to process primary sulfide ores which make up about 80% of today’s ores.[2] For this reason, this emerging technology is poised for exciting growth. Unfortunately, as with any process change, the implementation of HL projects requires significant training on both the control system as well as the underlying process, and further, due to the complex nature of the HL process, this can be a particularly difficult task. DEMOGRAPHIC TIME BOMB Even before the implementation of these new technologies, the availability of the skilled workforce has already become a significant problem for the mining and mineral processing industries. From a survey of 912 mining professionals, Stratum International found that a mere 0.4% of senior level candidates were between the ages of 25 and 34 and a similar proportion aged over 75 years.[3] This indicates that there is both a deficiency of young skilled workers and a skilled workforce that is retiring earlier than the previous generation. Combined with data published by the US Department of Labor stating that the median age of the mining workforce is approaching 50 years old, research suggests that up to 50% of skilled mining and mineral process professionals are expected to retire in the next 5 years, leaving with their irreplaceable knowledge and experience.[4] While it is projected that the labor pool will be sufficient to fill open positions, the real question is if this young workforce will have necessary skill sets and experiences. In addition to a rapidly aging workforce and an inexperienced labor pool, a study done by the Oil and Gas Journal showed that it takes about 7 years, on average, for new workers to achieve a level of competency that permits them to assess risks and appropriately make decisions.[5] Not only is this figure is in direct conflict with the typical tenure of 5 years in one position meaning that the thinly spread skilled labor will be required to become senior staff before they are able to achieve competency in their current role, this also means that these millennials are not given the opportunity to become competent in their role before the retirement of the more experienced workforce."

Jan 1, 2016