Search Documents

By Ernest M. Spokes

Maximum fan efficiency can only be obtained when the fan has the correct combination of size, speed, and blade setting to provide the required flow of air against the mine resistance. As the mine grows older, resistance decreases unless old workings flow is restricted, and new combinations of speed and blade setting or different fan sizes may provide greater economy.

Jan 1, 1977

By Richard Chojnacki

The western united States is not usually noted for the production of fluorspar; however, many significant fluorspar districts do occur in the Rocky Mountain region and constitute a resource of sizable dimension and major potential. This is particularly true within the area of the West served by the rail lines of the Union Pacific Railroad (see Figure 1). Fluorspar deposits near the Union Pacific have produced over 1.3 million tons of finished fluorspar products from 2.3 million tons of ore. Approximately 80% of this production was of acid-grade and 20% of metallurgical-grade fluorspar. Production of ceramic-grade was negligible. Through the years substantial production has come from eight mining districts. Five of these have produced metallurgical-grade and three acid-grade. The best-known fluorspar producing area in the West is the Jamestown Mining District. It was one of the first producers of fluorspar in the western United States and is estimated to have produced over 500,000 tons of finished fluorspar from over a million tons of ore. The district encompasses approximately 36 square miles in central Boulder County, Colorado, about 9 miles northwest of the City of Boulder. Although small shipments were made from the district as early as 1873 or 1874, significant sustained production was not achieved until 1940 when the General Chemical Company, now a division of the Allied Chemical company, acquired the Alice, Burlington, Chancellor,

Jan 1, 1971

By Tung Vu, Michael Harrington

"The Regional Connector project is a complex subway light-rail project that runs through the heart of downtown Los Angeles, CA. The design-build contract was awarded in April 2014 to the Regional Connector Constructors (RCC), a joint venture between Skanska USA Civil West California District Inc. and Traylor Brothers Inc., and their designer team consisting of Hatch Mott McDonald (HMM) and subconsultants. The project broke ground on Sept. 30, 2014 and is expected to be completed in winter 2021-2022. The main components of the project consist of 6.4-m (21-ft) diameter twin-bored tunnels, three crosspassages, a 87-m (287-ft) long crossover SEM cavern, three new underground stations, and cut-and-cover tunnels along South Flower, Alameda and 1st Streets. The project map is shown in Fig. 1. The design and construction challenges associated with each of these main components are discussed in the following sections.Project designTunnels. The Regional Connector tunnels are located primarily within the Fernando formation consisting predominantly of extremely weak to very weak, massive, clayey siltstone. About 305 m (1,000 ft) of tunnels on the eastern end are in alluvium and mixed face of Fernando formation and alluvium. The tightest curve of the tunnel alignment is 178 m (583 ft) in radius. The tunnels were designed with a reinforced precast concrete tunnel lining (PCTL) to be used with an earth balance pressurized (EPB) tunnel boring machine. The PCTL ring is 5.5 m (18 ft-10 in.) inside diameter, 27 cm (10.5 ft) thick, 1.5 m (5 ft) long, and consists of five segments and a key. The segments were designed with 6,500 psi concrete, 80 ksi yield strength wire rebar, convex joint surfaces to enhance seismic performance, and a dosage of 1.7 lbs polypropylene microfibers per cubic yard of concrete for fire resistance. The rings are designed with a right ring and left ring pattern and a taper of 3.8 cm (1.5 ft) to allow for alignment curve negotiation. Figure 2 shows typical sections of the PCTL. The structural lining design was modeled using FLAC 3D. Four consecutive rings were modeled with 32 dowel connection. Loading considered in the lining design includes temporary ground load during excavation, long-term ground loads, seismic loads and train loads. The seismic loads on the PCTL were simulated with the racking deformation applied at vertical boundaries of the model. Due to variation of geologic condition along the tunnel alignment and different surcharge requirements, three different types of reinforcement (typical, heavy and extra heavy) were designed. The typical type PCTL was required in Fernando formation, the heavy type was required in alluvium or mixed-face condition, and the extra heavy type was required in alluvium and underneath the Japanese Village Plaza where a surcharge of 1,000 psf was required."

Sep 1, 2019

By Kim B. Shedd, Erin A. McCullough, Donald I. Bleiwas

"The earliest known use of cobalt was to make blue glass in Mesopotamia before 2000 B.C.E. Since then, innovations across many diverse industrial sectors transformed cobalt into an essential commodity for contemporary society. The physical and chemical properties of the element cobalt and its alloys and compounds make them indispensable for a variety of applications, including aircraft engines, hybrid electric vehicles, machine tools, missile guidance systems, petroleum refining and smartphones. As a major industrialized nation, the United States is a leading consumer of cobalt and cobalt-containing products. However, with few exceptions, U.S. cobaltcontaining ore deposits are of low cobalt grade. Historically, U.S. cobalt mine and refinery output have not met domestic cobalt demand. As a result, U.S. cobalt chemical and alloy producers need to procure most of their cobalt from the international market, which can become susceptible to supply risk.The 1978 Cobalt Crisis illustrates supply risk. At that time, the Democratic Republic of the Congo (DRC) (then known as Zaire) was the world’s leading producer of mined and refined cobalt. An insurgent invasion of the country’s copper-cobalt mining region during a period of high cobalt demand and low producer inventories caused a temporary supply shortage in the international market. The monthly average cobalt spot price increased from $18/ kg ($8/lb) before the crisis to $99/kg ($45/lb) seven months later. The high price and concern about potential disruptions in supply prompted manufacturers to reduce or substitute for cobalt where possible, and encouraged increased recovery of cobalt from scrap. The DRC has regained its position as the leading producer of mined cobalt globally and continues to be characterized by high governance risks (U.S. Central Intelligence Agency, 2015; World Bank, undated). This article will present current and historical world cobalt production trends, which can help inform discussion about the variety of international supply chain risks consequential to its trade."

Jan 12, 2017

By T. H. Combs

Increased productivity in the U.S. underground coal industry has taxed pre-existing conveyor belt haulage systems. The usual remedies are costly and can disrupt production. A reduction in the belt feeder discharge rate on mobile haulage sections results in more uniform loading and reduces the spillage vulnerability. An investigation is made to determine the effect, if any, on shuttle car discharge time arising from lower feeder discharge rates. A five-section, underground mine is visualized, and belt spillage is introduced. The sectional feeder discharge rate is progressively lowered until spillage is precluded. At each level, the simulated spillage is measured and compared to the loss in face production. Methods of predicting the loss in face production from lower feeder discharge rates are discussed.

Jan 1, 1993

By T. P. Weldum, W. Conger

"These studies address the relationship between mill media sizing and its grinding efficiency. Starting with the results from a review of the literature, the issues of initial media sizing for a new ball milling circuit, and then optimal media sizing for an existing milling operation, were studied. The Functional Performance parameters “Mill Grinding Efficiency” and cumulative “Mill Grinding Rates” from both plant and test-scale equipment were used, and provide valuable new insight into this topic. A plant media sizing diagnostic tool is presented, as are newly developed testing equipment and evaluation methods, and recent case studies. REVIEW OF MEDIA SIZING LITERATURE For a plant metallurgist to answer the question “How can I maximize plant profit by manipulating this grinding circuit variable?” she must know what effect the variable has on grinding circuit efficiency. Despite the significant cost of grinding media and its potential effect on production capacity, the ‘best’ media sizing remains ill-defined for any given ball mill circuit in the industry today. The underlying reasons for this will be discussed. But the importance of this issue drove Metcom and its industrial partners to take on the challenge of how to engineer the ball charge for an existing grinding circuit. In the absence of any proven method, the first step was a review of the literature. Sponsored by Cleveland-Cliffs, Inc., a broad review of the literature was undertaken, producing “The Effect of Media Sizing on Ball Milling Efficiency” (McIvor, 1997). Among hundreds of publications that were reviewed that discuss the topics of media sizing or wear, forty-five were studied in detail. These were grouped into: plant experiences; laboratory and pilot plant investigations; media wear studies; population balance modeling studies; and general papers on ball milling which included the topic of media sizing. The reader is encouraged to refer to that review. The findings remain unchanged, although some relevant papers have been written since (e.g. Staples et al, 1997; Banasi et al, 1999; Orford et al, 2006; LaMarsh, 2015). The main findings of the review were as follows."

Jan 1, 2018

By Emily Adelsohn, Robert Winn, Anthony Iannacchione

"Over 600 longwall panels have been mined in Pennsylvania in the last 50 years. Of those 600 panels, 25 panels undermined interstate highways. Despite this quantity of panels, much is still unknown regarding the detailed effects of undermining highways. The Gateway Mine, the Emerald Mine, and the Cumberland Mine undermined I-79 with 17 panels between 1982–1989 and 2003–2008, respectively; mine Eighty-Four undermined I-70 with 4 panels between 1987–2000.Through the examination of the panels that undermined I-70 and I-79, it is possible to determine which factors have most impacted the highway alignments. In some locations, the highway intersects with panels at angles ranging from 45 to 80 degrees, and at others, it runs between two panels, which simulates the effect of gateroads on the subsidence. The panels width to overburden ratio varies between 0.64 and 1.7, meaning that the interstates were influenced by both subcritical and supercritical subsidence basins. The face advance rates and overburden depths also vary between the panels.Unfortunately, specific information detailing highway impacts associated with unique characteristics of the subsidence basins are limited. However, using the profile function model and influence function model within the Surface Deformation Prediction System (SDPS), the effects of overburden, panel size, and orientation of the road to highway can be indirectly assessed by profile and influence models of subsidence basin formation.INTRODUCTIONCoal mining has been an integral part of Pennsylvania’s history. Room-and-pillar mines have been active since the late-1700s when coal was extracted from outcrops. By 1830, the city of Pittsburgh alone consumed more than 400 tons of bituminous coal each day for domestic and industrial use (PADEP, 2019). In the late 1960s, the face of mining in Pennsylvania changed with the development of full extraction longwall mines. Since that development, over 600 longwall panels have been mined in the Pittsburgh Coalbed in Pennsylvania alone (PADEP, 2019).As longwall mining and other forms of full extraction mining have increased in popularity, the amount of planned subsidence impacting the surface has also increased. The stresses and strains induced by longwall subsidence can cause damage to the surface as well any structures, water supplies, or water bodies that lie above the panel. Since the behavior of soils and structures vary, one way to study the surface effects of longwall mining is to analyze the impact on flat, rigid, pavement surfaces. Examining factors that vary the impact of subsidence with respect to highway alignment can demonstrate the favorable orientation of an alignment to avoid or mitigate damage and critical impact zones in a subsidence basin."

Jan 1, 2019

By R. W. Amstutz

Abstract. The shaft was drilled on U.S. Government land in the Piceance Creek Basin and was funded by the U.S. Bureau of Mines. It was drilled to 723 meters (2 371') to provide access to rich deposits of oil shale, nahcolite and dawsonite for geotechnical test work and environmental mining research. Rotary drilling and dual string, reverse-air, jet-assist circulation methods were used. Drilling required 8 months. Site preparation, running and cementing the casing required another 4 months. A 2.44-meter (96-inch) ID steel welded casing, 5.1 cm (2 inches) thick was installed and 2 700 tonnes (63 000 sacks) of cement were slurried and pumped into the annulus.

Jan 1, 1980

By T. W. Beck

Drilling into coal mine roof strata to install roof bolts has the potential to release substantial quantities of respirable dust. Due to the proximity of drill holes to the breathing zone of roof bolting personnel, dust escaping the holes and avoiding capture by the dust collection system pose a potential respiratory health risk. Controls are available to complement the typical dry vacuum collection system and minimize harmful exposures during the initial phase of drilling. This paper examines the use of a bit sleeve in combination with a dusthog- type bit to improve dust extraction during the critical initial phase of drilling. A twistedbody drill bit is also evaluated to determine the quantity of dust liberated in comparison with the dust-hog-type bit. Based on the results of our laboratory tests, the bit sleeve may reduce dust emissions by one-half during the initial phase of drilling before the drill bit is fully enclosed by the drill hole. Because collaring is responsible for the largest dust liberations, overall dust emission can also be substantially reduced. The use of a twistedbody bit has minimal improvement on dust capture compared with the commonly used dust-hog-type bit.

Jan 1, 2014

By Alafara A. Baba, Yakubu A. Dallatu, Kehinde I. Omoniyi, Shemang Y. Chindo, Edith B. Agbaji

With the rise in global demand for pure copper, there is an urgent need to consider the processing of low-grade chalcopyrite ores. Ammoniacal leaching solutions have been reported as effective and efficient leachants for the dissolution of chalcopyrite. This work reports on different parameters that influence the leaching kinetics of a Nigerian chalcopyrite-rich siderite ore obtained from the Wase local government area of Plateau state, Nigeria, and assayed as 11.30 weight percent copper.

May 1, 2023

By Phil Dakin, Rajiv Chandramohan, John Lo Grande, Greg Lane

Crushing and grinding circuit availability is a critical design factor defining the installed equipment selection and the process buffers required to maintain throughput during maintenance. The comminution circuit typically accounts for a process plant’s largest capital expenditure and energy use. Effective process and equipment selection and layout optimization are crucial steps when combining the objectives of cost-effective design and high circuit availability in operation. This paper outlines fit-for-purpose design principles for optimizing process flow, eliminating standby equipment and reducing buffer residence time whilst improving maintainability and operability.

Feb 1, 2025

By Brianna M. Eiter, Jennica L. Bellanca

Mineworkers face a challenging and dynamic work environment every workday. To maintain a safe workplace, mineworkers must be able to recognize worksite hazards while they perform their jobs. Though hazard recognition is a critical skill, recent research from the National Institute for Occupational Safety and Health (NIOSH) indicates that mineworkers fail to identify a significant number of hazards. To further the understanding of mineworkers’ hazard recognition ability and to begin to address hazard recognition performance, NIOSH researchers analyzed data collected during a laboratory research study to determine the effect of individual mineworker factors including risk attitude, work experience, and safety training on hazard recognition accuracy. The results of this study show that mineworker risk attitude and safety-specific work experience affect hazard recognition performance while hazard-specific safety training does not. These results suggest that some of these individual factors can be overcome through experience and training. Potential strategies that can be used to address these factors are also discussed.

Aug 31, 2020

By Marcelo de Oliveira, Antoine Allanore, Dennis P. Chen, Davide Ciceri

Potassium fertilizers (potash) are mined in a handful of countries in the Northern Hemisphere. Potash is either expensive or unavailable to the farmers of the Southern Hemisphere. Alkaline alteration of K-feldspar rock (ultrapotassic syenite) in autoclave in the presence of Ca2+ generates a mixture of K-bearing calcium-aluminum-silicate-hydrate (C-A-S-H) minerals that potentially can be used as an alternative local fertilizer. This work investigates the effect of processing temperature (200 °C, 220 °C, and 230 °C) and time (from 0.5 to 3.0 h) on pH, mineralogy, and elemental availability of the C-A-S-H mineral mixture. Increasing temperature results in an increased conversion of K-feldspar and increased content of both the mineral tobermorite (Ca5Si6O16(OH)2·4H2O) and amorphous phase in the resulting C-A-S-H mixture; increasing time results in an increased conversion of α-dicalcium silicate hydrate into tobermorite. The amount of K leached from the mixture is relatively constant across all processing conditions. Hydrothermal alteration in autoclave of K-feldspar-bearing rocks such as ultrapotassic syenite permits the synthesis of a potential potassium fertilizer which alkalinity and mineralogy can be tailored according to soil requirements.

May 22, 2020

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.

By Simon Strong, Tim Brown, Luis Ignacio Sanz Vivanco

"One of the most significant technical and practical challenges facing the tunnel construction team on the Legacy Way road tunnel project in Brisbane, Australia was how to erect the pre-stressed precast concrete slabs to form the smoke duct in the tunnel boring machine (TBM) tunnels. An essential part of the tunnel ventilation system, the smoke duct, extends the full length of the 4.6km long twin, two lane tunnels. The vast majority of the tunnels (approx. 4.3km) were constructed using two 12.4m diameter double shield TBMs. The refurbished Herrenknecht machines broke several world records on the way to completing the tunnel excavation works in just over nine months. With the excavation complete the focus turned to solving the complex civil tunnel fit out challenges. A key component of the civil fit out of the tunnels was constructing the smoke duct in the TBM tunnels which was designed as a precast solution. The slabs which each measure 8.62m long by 2.0m wide by 200mm thick and weigh close to 9 tonne need to be erected above cast in situ corbels whilst other tunnel finishing works continue. The space proofing clearance offered by the design to the support corbels below and the precast segmental lining above was in the order of only 100mm. This paper details the events of how the Transcity JV tunnel fit out team, comprising some of Europe and Australia’s leading tunnel construction specialists, drew upon the global strengths of the existing JV member companies and the global reach of leading TBM manufacturer Herrenknecht to develop an innovative system to solve this challenging problem. This globetrotting story, which starts in Australia, visits Europe and mainland China before returning to Brisbane where it all began."

Jan 1, 2016

"A carefully planned laboratory test program is the foundation for the successful development of a sulfide flotation process. In this paper, the development of a copper-molybdenum flotation process is described. However, the concepts discussed can be applied to most sulfide flotation systems and to many industrial minerals projects as well. Each step is examined, beginning with sample procurement and covering sample preparation, flotation test preparation grinding, scoping flotation tests for reagent scheme selection, rougher flotation parameter evaluation and cleaner circuit evaluation, through to locked-cycle testing and pilot plant design and operation. Ore variability and modeling to determine the response of various ore types to the optimum conditions established is also examined.IntroductionA carefully planned laboratory test program is essential for the successful development of any sulfide flotation process. These programs usually begin with a series of batch tests on several ore type composites to evaluate appropriate reagent schemes and delineate optimum rougher flotation conditions, such as primary grind size, flotation pulp density, flotation pulp pH and retention time. Cleaner parameters such as regrind size requirements, cleaner pH, pulp density and number of stages are then defined. Semicontinuous locked-cycle tests are performed using the parameters established in the batch tests to determine the effect of middling streams recirculation on flotation performance. The data generated and the experience gained in the locked-cycle tests may be used to design and operate a continuous pilot plant if relatively large amounts of concentrate are required for further process development, such as optimization of byproduct molybdenum production from bulk copper-molybdenum concentrate.A comprehensive ore variability program is undertaken to determine the response of various ore types to the optimum conditions established. These ore variability programs often test hundreds of samples in standardized batch rougher and cleaner tests to ensure that the orebody is well understood.This article describes the development of a copper-molybdenum flotation process, but the concepts discussed can be applied to most sulfide flotation systems and many industrial minerals projects. The block flow diagram in Fig. 1 provides an overview of the development process."

Jan 1, 2016

By David B. Brooks

I gratefully acknowledge the help of a number of American and Canadian geologists, in both federal surveys and in private firms, who took the time to discuss this problem with me. Hans Landsberg and Bruce Netschert also followed the study with interest and encouragement. In their 1961 monograph, THE FUTURE SUPPLY OF THE MAJOR METALS, Bruce Netschert and Hans Landsberg noted that identified potential resources (that is, known but submarginal resources) of lead and zinc were much lower relative to reserves (that is, known and supermarginal resources) than was the same ratio for other metals.1/ Put another way, it seemed that for such metals as iron, manganese, copper, and aluminum, slightly more favorable economic conditions or modest advances in technology would greatly increase reserves by permitting the exploitation of vest quantities of leaner or deeper or otherwise less valuable mineral deposits. But for lead and zinc, Netschert and Landsberg concluded that either: "(1) there is relatively little material below present cutoff grades; [or] (2) such material exists, but for some reason there are no data.? 2/ This situation, which they called "the lead-zinc anomaly" has been subsequently discussed by other authors. The purpose of this paper is to carry the discussion further by examining the evidence in favor of (1) and (2) and by advancing a third alternative.

Jan 1, 1967

By T. G. Legare

It is now well documented that trace amounts of silver, gold, and platinum group metals occur in certain geothermal brine deposits. A significant body of literature has been generated over the last twenty years which describes attempts to quantify the frequency and levels of these precious metals in the brines. This literature is often confusing and contradictory. For example Barnea 1 states that the Salton Sea geothermal field carries 2 ppm gold, yet more recent data by workers at Lawrence Livermore National Laboratory2 (LLNL) concludes that the gold level in Salton Sea brine is <0.07 ppb. They report a platinum level in one well of 55 ppb. This apparent contradiction may be explained by sampling source and technique, but is most probably explained by difference in analytical technique. Analytical techniques and problems will be discussed in the next section.

Jan 1, 1985

By F. L. Pirkle, W. C. Bagby

The International Mineral Valuation (IMVAL) Committee, founded in 2012, develops strategies for conducting mineral valuations. These strategies have been developed into a mineral asset valuation template called the International Mineral Property Valuation Standards Template and is part of IMVAL's work to establish consistent international standards for mineral property valuation and reporting. This template is a living document that is updated from time to time and is based on three core values or pillars (Fundamental Principles): Competence, Materiality, and Transparency. Objectivity, Independence, and Reasonableness may be applied as required by national codes or standards. The Template harmonizes international standards for valuation of mineral assets as real property and represents a consensus of current good practices. It is not a stand-alone reporting code and does not supersede existing national reporting standards. The Template deals with mineral-property valuation as distinct from mineral-project evaluation. INTRODUCTION In his 1989 book, “The New Realities”, Peter F. Drucker, Clark Professor of Social Science at Claremont Graduate School, California, stated: “Information is data endowed with relevance and purpose. Converting data into information thus requires knowledge. And knowledge, by definition, is specialized.” (p. 209) The discipline of mineral valuation is knowledge-based and requires a mineral valuer to collect, analyze, and interpret data that are material to a mineral valuation assignment. In so doing, the valuer turns the data into information (data come first, followed by information as determined by the mineral valuer) for use by the client (from whom the valuer obtained the mineral valuation assignment) and other intended users. The valuer uses his or her experience and education (each valuer’s knowledge base) supported by a foundation built upon competency, materiality, and transparency, the three pillars of mineral valuation (“minerals valuation”, “mineral-property valuation”). The International Mineral Valuation Standards Template (“IMVAL Template”, IMVAL”, “Template”), third edition dated May 2018, defines mineral valuation as: “The estimation of the Value of a Mineral Property in money or monetary equivalent. The word ‘valuation’ can be used to refer to the estimated value (the Valuation conclusion) or to refer to the preparation of the estimated Value (the act of valuing).” (p. 14) Furthermore, the IMVAL Template clearly separates valuation from evaluation: “The Template deals with Valuation, which is distinct from Evaluation. The distinction inherent in these defined terms is that Valuation addresses the estimation of value of a Mineral Property, whereas Evaluation addresses the broader assessment of a Mineral Property for an investment decision.” (p. 2)

Jan 1, 2019

By Sahendra Ram, Ashok Kumar, Rakesh Kumar, AMIT KUMAR SINGH, Dheeraj Kumar, Arun Kumar Singh, Rajendra Singh

This article offers an examination of a retreat mining method conducted at the Pinoura Mine in India from 2010 to 2017. The method is atypical for coal mines of India’s coalfields. The method executes depillaring in a single pass and does not require the formation of galleries and support installation in splits, thus, reducing the cycle time. A variety of observations are discussed throughout this work and emphasis is placed on field measurements and depillaring under weak roof (RMR = 40–45). This paper discusses design techniques, specifically the estimation of the snook (remnant pillar) size, and important practical observations after the fact. The execution of this method was eventually conducted in eleven panels.

Aug 4, 2020