Search Documents

By David A. Heitman

The Buick Concentrator is a highly automated operation which utilizes a process control system for continuous monitoring and control. The process control system development, installation, and application to the concentrator grinding and flotation circuits are presented in this paper. The design and implementation of analog field sensing instrumentation, a continuous on-stream X-ray analyzer, grinding and classfication circuit controls, and a recent digital process control system utilizing a centralized computer are discussed. Emphasis is placed on the project planning and installation of the digital control system including a presentation of future plans for continuing application of computer control.

Jan 1, 1982

By Tristan Joubert, Fabio Panella, LiLing Chen, Yung Loo, Michael Devriendt, Nasir Qureshi, Ahmad Ali

Tunnel inspections have traditionally been carried out manually by inspectors writing up observations and taking photos of defects. The results from the inspection and the defects observed are dependent upon the rigor of the inspectors and may be subject to repeatability and consistency issues and is often time consuming with elevated health and safety risks. This paper will discuss work that is being carried out in developing and implementing an innovative hardware and software solution integrating machine learning to automate the process of capturing objective tunnel condition information, offering cost and programme savings as well as health and safety improvements

Jun 13, 2023

By Robert S. Shoemaker

The development of a metallurgical project is a business venture rather than a technical exercise, and its real objective is to obtain the maximum return on investment consistent with the limitations imposed by company policy and the requirements of society. Demand for profits is the driving force for technical advances and naturally leads to improvements in processes, equipment and plant designs. In the mineral dressing field there have been virtually no new processes developed since the introduction of flotation, and the steady erosion of profits by inflation has been offset only by increasing equipment size. Unfortunately, in recent years, plant designers have not always utilized the largest equipment or the opportunities for functional and economic design presented by the development of larger equipment. Lower cost plants can be developed providing that unrealistic restraints arising from the prejudice of past practices are avoided. As an illustration of this premise, three different approaches were taken toward the design of a clearly delineated but hypothetical copper concentrator of 20, 000 tons per day capacity. While the same flowsheet was used in each case, designs were produced for a conventional plant, an alternate using the largest available equipment, and a third scheme utilizing large equipment and the most functional design which could be developed, including features derived from many plants in many different industries. Capital costs were developed for the three separate designs based on a location in the southwestern United States. Ancillary facilities were identical in each case and included a mine truck shop, a maintenance shop, a general office, and a nominal starter dam for tailings disposal within 5000 feet of the plant. Water supply within 1000 feet of the plant, and power furnished to the property boundary has been assumed in each case. The flowsheet of the three plants is shown in Figure 1 and represents the treatment of a typical sulfide copper ore by three- stage crushing followed by single-stage ball milling. Concentration is by flotation roughing and scavenging followed by regrinding of the concentrates and two stages of cleaning.

Jan 1, 1971

By L. L. Anderson

Western bituminous coal can be processed to low sulfur liquid fuels by fast reactions. A process (LEFCO) under development at the University of Utah uses coal and catalyst under hydrogen pressure to convert 60 to 70 percent of the coal matter to fuel liquids and gases. Coals have been processed in small diameter (less than 1/2 inch) tubes and at reaction residence times of less than 10 seconds. Effects of process variables on the yield and quality of products have been studied. General features of the process and the properties and characteristics of the products produced are presented. Special features of the process that distinguish it from other liquefaction processes under development are also discussed.

Jan 1, 1975

By K. J. Sollman

As a class, silicate minerals have likely found the broadest, if not largest volume, use in combination with polymeric binders of all industrial minerals. Among the silicates, calcium metasilicate, wollastonite, enjoys a front runner position in a near universal sense. It is a viable and desirable part of composites ranging from thin films to large moldings; from a common filler/extender for paint for your garage to a reinforcement for the exterior surfaces of a luxury vehicle affordable to very few. This article is focused upon the variations in particle morphology and the surface characteristics which, by way of commercial examples and discussion of active research programs, make this environmentally benign mineral so unique.

Jan 1, 1993

By Saurabh Kundu, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Manikanta Nallamilli, Shaik Mahaboob Basha, Neha Gupta, Srinivas Dwarapudi, Dhiraj Madhukar Kadhe

Iron ore pelletizing using compressive and shear action on wet mixture feed has been studied. The physical properties, namely, moisture content, drop strength, green compressive strength (GCS), dry compressive strength (DCS), porosity, and cold crushing strength (CCS), have been studied. Pelletizing tests were carried out on four different types of ore, namely, hematite ore, magnetite ore, goethite ore, and sinter return fines. The inference of shear forces on silica distribution index in dry pellet has been studied using optical and scanning electron microscopy. Significant improvement in physical strength was observed due to compressive and shear forces on the pellet mixture feed. However, decrease in moisture content and ball porosity has been observed. Silica distribution index improved by 1.72 times for hematite ore, 1.47 times for magnetite ore, and 1.68 times for goethite ore. It has been found that bubble cavity has been reduced which is good indicator in terms of physical properties.

Jan 29, 2022

By T. Faulkner, S. A. Richards

"The Scale-Distance formula is one of the primary means of determining the maximum amount of explosives that can be safely detonated at one time by a single delay. This paper describes a method of applying the Scale-Distance formula to the entire mining area using gridded surfaces. Using this technique, the operator can better determine the economic impact of nearby structures on the mine plan. INTRODUCTION As the surface mining of coal and stone encroaches near populated areas, precautions must be taken to minimize blast vibration damage to protected structures. The common method employed to minimize vibration damage is not to reduce the total amount of explosive in the hole (which would negatively affect fragmentation), but rather to introduce delays to reduce the amount of explosive detonated at any point in time. The Scale-Distance formula, an industry-accepted standard, may be used to calculate the maximum weight of explosive that can be detonated at one time without damaging the structure. This information may then be used to determine the number of delays required for each hole. Detonators make up a large part of the cost of blasting. At roughly $15 per detonator an additional detonator in the hole can be significant. It is normal to set off hundreds of holes at in one shot. An additional detonator in each hole can cost additional thousands of dollars per shot. The number of detonators is also a function of the depth of the holes and the hole spacing. Being able to accurately forecast the economic impact of blasting near structures improves a company’s ability to make informed decisions on how to approach property owners. Operators basically have three options when dealing with property owners: 1. Buy the property and blast without restriction 2. Negotiate with property owner for a waiver to allow unrestricted blasting 3. Comply with the legal blasting restrictions This paper proposes a method for the engineer to forecast for all points in the proposed mining area the impact of nearby structures upon the blast design. Being able to create a contour map and ultimately estimate the number of delays required for the entire forecasted mining area, the engineer can create accurate economic forecasts of the cost of blasting. The objective is to reduce the level of uncertainty in the forecast of the blast component portion of the forecast."

Jan 1, 2016

By Lauro Lacerda

Shotcrete is a highly adaptable and widely used underground construction material at infrastructure and mining projects around the world. In fact, many projects could not have been completed without its utilization. As underground projects became larger the use of mechanized wet-mix spraying gradually replaced manual dry-mix shotcrete applications. This paper details some of the reasons for that and provides information on the equipment and operational factors including safety and productivity required to successfully complete underground shotcrete projects.

Jun 13, 2021

By L. Thompsen

High-pressure grinding rolls (HPGR) offer capacity increases, savings in operating costs and metallurgical advantages. The first installation of the Polycom HPGR in a copper ore treatment plant occurred in July 1995 at Cyprus Sierrita’s mining complex near Green Valley, AZ (Fig. 1). Until that time, the benefits this technology offers for copper and gold ore were only demonstrated on testwork. In other industries, such as diamonds, HPGR have proven to be reliable in industrial-scale plants and have set a new standard for this kind of ore treatment plant. HPGR are also successfully used for the comminution of coal, blast furnace slag and in cement and pelletizing plants. The installation at the Cyprus Sierrita Mine should prove the economical benefits in commerical-scale copper mining, confirming the results of comprehensive testwork(Fig. 2).

Jan 1, 1996

By Stanisław Prusek, CHONG WEI, Huawei Xu, Jun Wang, Andrzej Walentek, Artur Dyczko, Derek B. Apel

The excavation-induced stresses transferred from the panels or pillars in upper coal seams play a key role in the occurrence of rockbursts in driving roadways during close-distance coal seam mining, which has become a common problem and threat to many underground mines. The authors established a 3D finite-difference numerical model via FLAC3D software using the closedistance coal seam mining conditions in the Zofiówka Mine as a case example to reveal the rockburst mechanism in such conditions. The excavation-induced vertical stresses are analyzed, which provides a basis to build a conceptual model to explain the possible source mechanism of the rockburst under such conditions. Nine typical rockburst indicators considering different contributing factors are then selected as the evaluation criteria to assess rockburst potential in the study site. The results suggest that the superposition of multiple excavation-induced stresses of the main drift and tailgate provides an environment for stress concentration and energy accumulation. The side abutment stress induced by mining in the upper coal seam has a “strengthening” effect to the rockburst occurrence. The great deviatoric stress induced by complex excavating situations is another important exterior cause. A strict calibration procedure should be implemented before using indicators to predict rockburst potential. A methodology was proposed to estimate the location and magnitude of rockbursts combined with numerical modeling, laboratory tests, and feedbacks from the field. The study could provide some references and guidelines for preventing and mitigating rockbursts in underground mines under similar engineering conditions.

Aug 26, 2021

By O. Porterfield, M. O’Kane, M. Endersby

BHP Iron Ore initiated research programs in January 1995 to develop long-term plans for decommissioning waste rock material at its Mt. Whaleback operation. More than 2 Gt (2.2 billion st) of waste rock were deposited during the past 30 years. Ultimately, a total of 4 Gt (4.4 billion st) will be deposited in waste rock dumps constructed near the open pit. The Mt. Whaleback operation is located in a semiarid climate adjacent to Newman, Western Australia. The primary research program includes the development of technology for the long-term performance of the waste rock dumps with respect to vegetation, slope stability, surface runoff, erosion and water infiltration. This paper focuses on the design and implementation of a cover system to prevent water infiltration to the underlying waste rock. Data obtained from a laboratory program and from soil-atmosphere modeling was used to design horizontal field test plots. The construction of the horizontal surface field test plots is discussed together with the field instruments installed to monitor performance. The cover system is designed to maximize infiltration during wet periods for subsequent evapotranspiration while minimizing surface runoff. The result is a near-zero net infiltration to the underlying waste material. An important feature of the design is the use of run-of-mine waste material as the cover material. Monitoring is in progress and will continue for at least two annual wet/dry cycles. The optimum cover system should minimize the net infiltration of water to the underlying waste rock while maintaining physical and ecological integrity for long-term performance.

Jan 1, 2000

By Ali Kazmi, Wern-ping N. Chen

A load rating procedure was performed to evaluate safe load capacity of the Port of Miami Tunnel (POMT), FDOT Tunnel No. 871071 SR 887. The rating procedure performed on a total of eleven stations beneath roadways and with fill depth less than the tunnel exterior diameter (42 ft). Calculations on tunnel sections passing beneath roadways were performed to evaluate the structural response of the sections subject to moving vehicular loads, dead load, and earth pressures. Ratings were performed in accordance with AASHTO and FDOT guidelines. The procedure considered two types of vehicles (HL-93 and FL-120) and two rating levels (Design level and Permit level). As part of HL-93 vehicle, Tandem load was also considered for rating, separately. For HL-93 and HL-93 Tandem, inventory and operating level ratings were performed. The results show rating factors are high. The minimum rating factor is 16.8 using Inventory truck HL-93. For Permit level using FDOT FL-120 truck the minimum rating factor is 6.9. As can be seen, rating factors are higher than comparable analysis for bridges. This paper explains how the procedure can be implemented for tunnels and evaluates the rating results.

Dec 1, 2022

By Veerendra Singh, NILAMADHABA SAHU, ARIJIT BISWAS

Manganese alloys are important raw materials for steelmaking. However, selective mining of high-grade manganese ore resources has resulted in a scarcity of these high-grade Mn ores (Mn: >42; Mn/Fe: >5). The present research work is carried out to explore a new smelting reduction process to produce high-Mn/Fe syntheticMn ore from low-grade ferruginous manganese ores. Representative samples of low-grade ores (Mn: 25–30%; Mn/Fe: ~1) were collected and smelting reduction studies were carried out using variable smelting power (20–30 kWh), carbon rate (10–20% of ore) and slag basicity (0.1–0.3) to produce high-MnO slag and manganese pig iron. Studies have shown that different-grade high-MnO slags (MnO: 38.57–58.24%; Mn/Fe: >15) and manganese pigs (Mn: 5.16–24%) can be produced at optimum process conditions. The high-MnO slag can be used as synthetic ore for the ferroalloy production process. The developed process is capable to effectively segregate the iron and manganese in the metal and slag, respectively. The optimum Mn and Fe separation (>95%) was achieved by smelting of 10 kg Mn ore batch in a 50-kVA electric arc furnace using 30 kWh smelting power and 0.16 kg of coke. The slag basicity was maintained at 0.3 and the optimum slag SiO2 was ~30%. The studies indicated that the upgrading of low-grade ferruginous manganese ores is a promising solution for achieving high-Mn/Fe-ratio synthetic ores for ferroalloy production. It can help the manganese alloy industry to overcome challenges associated with the scarcity of high-Mn/Fe-ratio Mn ores and efficient utilization of low-grade resources.

Aug 3, 2020

By J. M. Mutmansky

This paper outlines the results of a study of opinions of practicing engineers concerning the value of environmental engineering courses in a mining engineering curriculum. One hundred engineers with significant experience in mining-related engineering work were carefully chosen. Of the sixty-seven responses received, about half were from mining engineers and half from environmental engineers. The results of the survey are outlined in detail. The number and type of courses recommended by the respondents are summarized as well as the specific topics recommended for inclusion in a mining engineering curriculum. The survey form also asked for the stages in the mine life when environmental experts were needed and the percentage of environmental engineering performed by outside experts for many mining-related environmental tasks. The results of this line of questions are provided. Finally, the paper offers a comparison of the results for environmental engineers and mining engineers and analyzes the differences.

Jan 1, 2001

By E. Costa Silva

Among the methods of mineral processing, gravity concentration methods are, probably, those which have lower costs, higher capacities and lower operational complexity. In order to be really effective, these methods require a feed size distribution in which the particles are liberated. Further, there must be a significant difference (usually higher than 1-1.5) among the real densities of the particles. However, in most cases, the traditional gravity concentrators (jigs, shaking tables, spirals and dense medium hydrocyclones) lose efficiency (sharpness of cut and recovery) when the mean diameter of particles are lower than 0.05mm and the difference among densities are smaller than 1. Most gravity concentrators developed in the last 20 years are based on the use of centrifugal forces that create large "apparent gravitational gradient" seeking to overcome the limitations of particles size distribution. This paper presents the experience of the CVRD Research Center in evaluation and development of new process based on using this new generation of gravity concentrators.

Jan 1, 1999

By W. R. Reed, W. J. Archer, A. B. Cecala, J. D. Potts

The U.S. National Institute for Occupational Safety and Health (NIOSH) uses light-scattering real-time dust monitors (nephelometers) in its research to develop dust controls to reduce respirable silica dust overexposures in miners. Recently, the model 1500-pDR, an active nephelometer (i.e., with cyclone and pump configuration), was introduced by Thermo Scientific. Testing was completed to ensure compatibility with the metal/nonmetal mine dust personal sampling unit (M/NMDPSU). Results of testing demonstrated that gravimetric concentrations measured from the 1500-pDR are comparable to the gravimetric concentrations measured using the M/NMDPSU, without need for correction, under commonly observed dust loading conditions.

Jan 1, 2012

By C. Nesbit, N. Duru

During the cyanide leaching process of gold and silver, ores that come from the transition zones which typically con-tains low levels of sulfide may produce one or more of the following reduced sulfur species: sulfide (HS ), polysulfides (Sn ), thiocyanate (SCN ), thiosulfate (S2O3 ), trithionate (S3O6 ), tetrathionate (S4O6 ), pentathionate (S5O6 ) and hexathionate (S6O6 ). The actual speciation of the reduced sulfur species in the circuits will primarily depend on the re-dox potential, pH, cyanide levels and existing sulfur species in recycled process water, as well as the presence of other reac-tive metal species. Development of an accurate analytical method for sul-fur species in cyanide leaching units of gold ores where sul-fur speciation occurs has an important role in explaining the metal recovery deviations. This study presents the speciation of sulfur species and development of an ion chromatography method to analyze the reduced sulfur species thiocyanate, thio-sulfate, trithionate and tetrathionate in cyanide leaching circuits for gold ores. The method developed has resulted in the precise quantification of target sulfur species in leach solutions.

Jun 1, 2024

By Dushasan Kundu, B. N. Shivakiran Bhaktha, Khanindra Pathak, Sarbojit Mukherjee

Mine safety and quality of life of miner working in underground mines depend to a large extent on mine illumination and communication. The provisioning of reliable, safe, and cost-effective illumination is critical, particularly in underground gassy coal mines. To prevent firedamp explosion by electrical switching operation in coal mining industry requires implementing intrinsically safe illumination circuit. The luminaire design also needs to be certified and installed properly. The current illumination systems installed inside mines require a lot of energy which is obtained from nonrenewable resources. In this work, the design and implementation of solar-powered optical fiber-based illumination are studied and implemented in the Jhanjra underground coal mine, Eastern Coalfield Limited, and a Li-Fi-based communication system for underground coal mines is proposed. Silicate optical fibers of various core diameters and numerical apertures are characterized for illumination applications and their efficiencies are reported. The possibility of achieving optical fiber-based solar, laser, and hybrid illuminations in underground mines is discussed. The design and fabrication of a Fresnel lens-based solar tracker for solar illumination are also presented. The optical fiber-based illumination system is installed in an underground coal mine and the illumination of over 70 lux is achieved at the work plane. Finally, optical fiber-based illumination and simultaneous basic Li-Fi communication are demonstrated and will be beneficial to the underground coal mining industry.

Apr 14, 2023

By Ebrahim Ghasemi, Mohammad Hossein Kadkhodaei, Mosareza Jalilian

Entry-type mining methods, such as cut and fill method, play a significant role in underground mining, and they are still suitable methods for extracting deposits with irregular shapes and with weak host rocks. In these mining methods, the stability of the open spans is important for improving worker safety and increasing ore recovery. This study focuses on the application of six data mining classification methods, namely multinomial logistic regression (MLR), classification and regression trees (CART), logistic model tree (LMT), decision tree (J48), multivariate adaptive regression spline (MARS), and gene expression programming (GEP), in order to develop predictive models for stability assessment of underground entry-type excavations. For this purpose, a database containing 399 case histories of entry-type excavations from seven Canada underground mines was used. These models predict the stability status of entry-type excavations based on two input parameters, dimensions of the span and rock mass rating (RMR). The performance of developed models was evaluated using six performance metrics namely accuracy (ACC), sensitivity (SE), precision (PR), Matthew’s correlation coefficient (MCC), area under the receiver operating characteristic (ROC) curve (AUC), and performance index (PI). The results showed that all developed models can be used to predict the excavation stability, but the comparison of models indicated that the J48 model provides the highest performance with ACC = 0.900, SE = 0.869, PR = 0.922, MCC = 0.835, AUC = 0.891, and PI = 4.417. Thus, the proposed J48 model can be applied to identify the susceptibility of span instability in the entry-type mining, and if instability has been predicted, the necessary measures, including the use of suitable support systems, can be considered to reduce the casualties resulting from span instability.

Feb 26, 2024

By M. Polat

Variations in flotation rate by particle size and specific gravity have been investigated for three different bituminous coals. The flotation rates for various components were determined by separating the products of bulk flotation into size-specific gravity fractions. The effects of feed size and reagent addition on the flotation response of individual size-specific gravity fractions were evaluated.

Jan 1, 1994