Search Documents

By W. W. Wen

A continuous pilot-scale test of the GranuFlow Process was conducted using a screen- bowl centrifuge for the dewatering and reconstitution of column flotation concentrate at a coal preparation plant in Virginia. In this test, a slipstream of the fine-clean-coal slurry from the column flotation concentrate was treated with a bitumen emulsion before dewatering. The treated products from the screen-bowl centrifuge appeared to be dry and in a free-flowing granular form, while the untreated products were wet, sticky, and difficult to handle. Specifically, test results indicated that the average moisture contents of the dewatered coal were 35.7, 35.5, 32.6, 29.9, and 26.5 wt% with Orimulsion additions of 0,0.7,3.2,4.8, and 6.4 wt%, respectively. The handleability and dust reduction of the dewatered coal product were also vastly improved.

Jan 1, 1997

By G. Deschênes

In Part I of the work, gold and silver were shown to be efficiently extracted from Kupol samples using lead nitrate in a cyanide leach system. In Part II, a comparison of the technical and economic merits of a new technology called CELP (CANMET Enhanced Leaching Process) was made with the cyanidation/AVR(Acidification-Volatilization-Recycling) process using 8 metallurgical variability samples as well as a large composite sample which represented initial two years of Kupol mill feed. The composite sample had 33.4 g/t Au and 289 g/t Ag. The metallurgical demonstrated that the CELP produced very similar gold and silver leach extractions compared to the standard Cyanidation /AVR leach conditions at 1/2 the cyanide concentration (1000 ppm NaCN in CELP vs. 2000 ppm for cyanidation/AVR leach conditions). It was estimated that the total cost per ton, were approximately the same for the two technologies (total cost of the CELP with the use of Merrill-Crowe at $46.48/ton, with cyanidation/AVR at $46.13/ton). However, the implementation of the CELP would eliminate a capital expenditure of approximately $5 million. Eight variability samples used to confirm the previous results showed that on average the gold and silver leach extractions with the CELP and the feasibility leach conditions were very similar for gold extractions, but 4.6% higher for silver extractions compared to the conventional cyanidation. The decision was made to remove AVR cyanide recovery from the Kupol flowsheet and implement the CELP at Kupol. The ability to use conventional leach equipment with the CELP and simplify the flowsheet was also a factor, given the remote location of the Kupol Mine.

Jan 1, 2009

By T. J. DeMull

The business of heap leaching requires accurate forecasting of metal production from the heaps. Business forecasts typically follow a format that project periodic (monthly, quarterly, or annual) product shipments based on anticipated operating results, e. g., tons of ore placed, grade of ore, and rate of leach extraction. Since revenue and cash flow are dependent on the metal production stream, forecasts of metal production are very important for project evaluation and business planning purposes. Nevertheless, production forecasts, particularly for new heap leach projects, have been prone to errors. The present paper identifies some of the pitfalls that would be encountered in preparing production forecasts for new heap leach operations and provides a checklist of considerations to assist in preparing a forecast. Also, the paper presents a case study of copper production forecasting used for the Sanchez Project, a heap leach operation located near Safford, Arizona, that is presently under development by AZCO Mining, Inc.

Jan 1, 1995

What is your personal view and assessment of the overall health of the industry in the current global economy? The economic outlook remains soft for the near future and, although the global economy is showing signs of recovery, uncertainty has tempered the pace of recovery. In addition to uncertainty, we are still facing significant economic challenges in many parts of the world, including Europe and the United States. The rapid expansion of China?s economy has recently slowed, further contributing to the sense of uncertainty in the overall health of the global economy. This situation is both a blessing and a curse, depending on which sector of the mining industry we are considering. For example, coal, industrial minerals, aggregates, base metal and precious metals markets are impacted by different forces and drivers and will experience different outcomes within the same economic environment. Let me give a few concrete examples to illustrate this concept. The prevailing economic uncertainty that I have just described tends to drive investors toward safe havens. Gold has historically been viewed as a safe haven and as long as investors shy away from traditional investments, gold prices will remain high and gold mining companies will continue to expand and invest capital in their operations. The same sluggish economy that drives gold prices higher has the opposite effect on other segments of the minerals industry. A great example of this is industrial minerals and aggregates used in construction. The markets that consume these minerals have contracted significantly over the past five years. The outlook for this segment is poor, as the glut of available housing continues to inhibit demand for new construction and, thus, many industrial minerals. In addition to this, the federal government?s lack of political will to enact long-term legislation funding transportation and infrastructure projects continues to be a drag on the U.S. aggregates industry.

Jan 1, 2013

By C. G. Buttleman, W. C. Brice

In Minnesota, reclamation of active aggregate mining sites is primarily regulated through local permits issued at the county, township, or municipality. However, for abandoned or depleted aggregate mining sites, a responsible party for reclamation is often no longer available. Since 1995, the Minnesota Department of Natural Resources has reclaimed several abandoned aggregate sites using innovative public/private partnerships and emphasizing native plant materials. The purpose of these projects is to demonstrate cost effective reclamation methods that can be utilized by both aggregate operators and local government and to promote mine planning and resource identification as it relates to reclamation.

Jan 1, 2000

By F. Calizaya

This paper explains and discusses a computer program developed to determine the ventilation design parameters for complex auxiliary ventilation systems such as those found in the construction of long excavations with multiple headings. The program is based on the principle of partitioning the system into segments of finite length, and formulating and solving the resulting networks recursively. The application of the program is illustrated by the detailed solution of an auxiliary ventilation system proposed for the Exploratory Studies Facility (ESF) at the Yucca Mountain project, Nevada.

Jan 1, 1994

By T. Hawthorne, H. Barnes

Homestake Mining Company has developed an estimating model, based on other closed projects, to audit and prepare new estimating plans. The results of recent closure audits reveal that the original budgets were often insufficient to cover the present expected expenses. Some of the major areas where technical challenges and costs are increasing include heap leach pile detoxification and rinsing, tailings dam closure, water management and treatment, abatement of contaminated soils, and many others. Risk and sensitivity analysis of each category will develop a level of confidence in the estimate and allow management to focus on the pertinent issues. Periodic audits of closure plans and costs throughout the life of mine serves to focus management attention on the complete costs of production. This will result in improved overall planning and management, and reduce the number of missed opportunities for savings.

Jan 1, 2000

By M. Li, J. D. Miller

During the past decade, considerable effort has been made to develop improved flotation strategies for the sedimentary phosphate resources from Florida, particularly the dolomitic phosphate resources. New flotation equipment and alternate flotation strategies have been evaluated. These developments are reviewed for both traditional siliceous resources and future dolomitic resources. Most process strategies involve variation in the reagent sequence and/or the use of depressants/dispersants. Further research and development efforts in flotation technology are needed to increase flotation plant capacity by elimination of the conventional double float process, to improve the recovery of coarse phosphate, and to achieve the desired selectivity with respect to carbonate minerals, particularly dolomite.

Jan 1, 2000

By R. D. Williams

"In a very real sense, Butte, MT is where the copper came from that won two world wars. The price for that unrestricted mining and smelting of copper came due in 1983 when Butte was declared a Superfund site.One of the most complex remnants of this mining history is the Parrot Tailings site. The Parrot smelter operated from 1881 to 1910, moving Upper Silver Bow Creek to the south and depositing approximately 283,000 m3 (370,000 cu yd) of waste material adjacent to Upper Silver Bow Creek. Additional mixed waste from other processing sites deposited below the Parrot tailings at the Northside Tailings, Diggings East and Blacktail Creek Berm total approximately 171,000 m3 (224,000 cu yd) of contaminated material. As part of the Superfund remedy, the U.S. Environmental Protection Agency (EPA) proposed leaving all these wastes in place. This proposal prompted a detailed criticism by several geoscientists familiar with the site. The EPA’s 2006 Record of Decision (ROD) did in fact leave these wastes in place, which set the stage for a series of studies that continue to refine how best to protect extensive completed Superfund Remediation downstream of Upper Silver Bow Creek. History of the Parrott Mine and tailingsPlacer gold was discovered in Silver Bow Creek, the headwaters of the Clark Fork River only a few miles from the Continental Divide in 1864. This discovery led to a stampede of placer and lode claims. One of the first lode claims located was the Parrot lode, located in the fall of 1864. Progress for developing a mine at the Parrott was slow, and it was not until 1876 that one of the original locators encountered a rich vein of chalcocite. Butte had its first copper mine.The Parrott Mine was patented in 1879 and by 1881 the Parrot, having lost a “t”, concentrator and smelter were built. The smelter and concentrator were an immediate success with a considerable market for processing the district’s rich copper ore. In 1885, the employees of the Parrot smelter bought the Butte Reduction Works, another smelter. In 1885, dams were built on Silver Bow Creek to contain various tailings and related processing byproducts (Fig. 1).By 1890, the various smelters in Butte rendered Butte’s air quality as suffocating (Fig. 2). An 1889 funeral procession was rumored to have gotten lost in the thick smelter smoke and somehow ended up at the Centennial Brewery. A city ordinance was passed late in 1890 in an attempt to control smoke. The Parrot smelter employed approximately 500 men by 1890. Through the 1890s, the tailings produced grew from approximately 91 t/d (100 stpd) to more than 181 t/d (200 stpd). Copper values in the tailings were initially as high as 4 percent, but as the processing improved that was reduced to 1.5 percent."

Apr 1, 2019

By J. W. Motter

Currently, virtually all new electric power generation systems under construction are designed with natural gas as the primary fuel. Factors driving these construction decisions involve sustained low prices for natural gas, environ-mental (and consequent regulatory) risks associated with the use of coal for power generation, and relatively high costs of construction for conventional coal-fired power plants. Despite the unarguable abundance of coal in the US. and worldwide, a fundamental question arises: What will be the role of coal in electric power generation in the 21st century? Congress, recognizing the vital and strategic importance of preserving the coal option for electric power generation, authorized the Clean Coal Technology Program. This pro-gram, with original funding in excess of $2,500 million, is intended to promote the demonstration and commercialization of a new generation of clean, efficient coal-based energy technologies through collaboration and partnering with private industry. The two technologies being demonstrated under this program which are the key to the continued use of this nation's huge coal reserves are coal gasification and the pressurized fluid bed. Either or both of these technologies, coupled with a combined cycle will pro-vide the continuing future coal option, while responding to increasingly more restrictive environmental standards. Recent Congressional budget-cutting efforts, however, could threaten the effectiveness of that model program, and ultimately other subsequent government-industry collaboration.

Jan 1, 1996

By Phil Jones

"Dilution — planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a sixmonth period in fiscal year 2018 (FY18) that established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned versus actual toe data. These were rig alignment error, collar location change/ error and in-hole deviation.The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimizer system). The trials were undertaken in the same environment: the Cracow gold mine, an operating underground mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160 percent.The increased accuracy reduced stope dilution by reducing over-break of subgrade ore. The new technology was implemented at Cracow during the latter half of 2018. Despite utilizing the new technology for just six months of the year, the mine recorded a 5 percent overall reduction in dilution for the full year compared to the previous year (FY17); from 22 percent down to 17 percent (a net decrease of 22.7 percent). Mine management attribute a significant proportion of this reduction to the new technology, along with sequencing and planning improvements. This opinion is backed by detailed stope reconciliation data taken during the trial from 28 stopes — representing 20 percent of the total tonnes mined during FY18. The data identified that stopes drilled using the new technology recorded 62.6 percent less average dilution."

May 1, 2019

By R. C. Hopper, A. A. Mathews, T. A. Lang

DESCRIPTION OF PROJECT The Straight Creek Tunnel site is located approximately sixty (60) miles west of Denver, Colorado, on Interstate Route 70 in the vicinity of Loveland Pass, in the Rocky Mountains. The ultimate project will consist of dual two-lane vehicular tunnels with a building at each portal to house mechanical ventilation equipment and other installations. The tunnels run virtually east-west on an ascending 1.64 percent grade for a distance of approximately 8,900 feet, and will pass beneath the Continental Divide at an elevation of about 11,000 feet above sea level. The maximum cover is 1,450 feet and each tunnel is approximately 48 feet wide by 50 feet high as excavated. The work now under construction consists of the North Tunnel, which initially will have two-way traffic. Ultimately it will be the west bound lanes for Interstate 70. The completion of the North Tunnel will be the fulfillment of a long felt need for better communication through the high Rocky Mountains of central Colorado and is a vital link in Interstate Route 70. The early planning for a vehicular tunnel through the Continental Divide began in the late 1930's and between November, 1941 and May, 1943 an exploratory pioneer tunnel

Jan 1, 1997

By S. Gering, R. Ruiz, C. H. Calderon-Arteaga, J. Barrios

"Located in the northeast corner of Zacatecas State, Mexico, the Peñasquito operation is comprised of the Peñasco and Chile Colorado (Brecha Azul) deposits. Openpit mining (prestripping) began in 2010 and full production commenced during 2011. The openpit mines feed both a sulfide concentrator (mill) and a heap leach pad. The project is owned by Goldcorp Inc. Peñasquito is a poly metallic deposit with Au, Ag, Zn and Pb being recovered as payable metals.As a consequence of lower grade ores expected with advancing mine life, Peñasquito is facing a declining metal production profile. To maximize returns and asset value, plant modifications, including the addition of a carbon prefloat circuit and a pyrite leach circuit to improve recovery, are currently being undertaken. This carbon prefloat circuit will enable the recovery of precious and base metals from carbonaceous sediments. This material is currently being stockpiled. With the associated increase in complexity in the process circuit, the requirement of the ore control system to accurately predict ore feed characteristics is critical to maximizing metal recovery at the Peñasquito operation. The addition of the carbon prefloat circuit was also a key driver in allowing the Chile Colorado openpit to be developed.These conditions alongside Goldcorp’s drive to increase profitability and maximize net asset value has created challenges. These challenges are numerous and multifaceted. However, the ability to accurately route materials from the ore control system is critical to site success, and some of these challenges have been overcome by the adoption and implementation of a new ore control (OC) technology. Examples of these technological innovations in the ore control program are discussed in this article and include improvements in geomodeling, material routing and reconciliation. Successful implementation of these elements has led to significant improvements in selectivity, performance and data management, while reducing the variance between planning and execution, thus helping to drive overall improvement across the operation."

Jan 7, 2018

Like the Summer Olympics and U.S. presidental elections, MINExpo comes along once every four years. More than 35,000 people attended the last MINExpo and there is talk that there will be more this time. Just about every company that has anything to do with mining, 1,822 to be exact, will exhibit their wares at the show, but it is the ones rolling in the massive equipment that make MINExpo the show that it is. The following is a glimpse at some of the companies and equipment that you can expect to see at this year?s MINExpo.

Jan 1, 2012

By Roger M. Buckeridge, Charles D. Reese, Silvio M. Martino, William T. Carey, Ansel H. Graham

FUNCTIONS OF RAIL HAULAGE SYSTEMS The principal application of rail haulage in under¬ground mining is in the movement of ore or coal pro¬duction from near the mining areas out to a processing plant. In some cases, such production haulage may end at a shaft pocket or slope belt conveyor transfer station, depending on the type of mine and the geo¬logical placement of the mineral being mined. Main-Line Haulage The basic reasons for choosing main-line rail haul¬age are high-tonnage production per shift and long haulage distances. The choice between rail and other systems, such as belt conveyors, is not easy and requires an integrated study of many factors: tonnage, distance, grade, product size, number of producing areas, ore reserve, safety, capital cost, operational and maintenance cost, and the mining system. Projecting a main-line rail haulage system for com¬parison with other systems requires a choice of many variables which are interrelated. The project must start with consideration of the mining system, tonnages per day, distances and grades, and loading and dumping conditions. Rail mine cars of different sizes and types are studied. High tonnage demands consideration of wider track gages. A suggested minimum for metal mines is 914.4 mm (36 in.); for coal mines, 1066.8 mm (42 in.). The choice of the train size should be governed by tonnage per shift, physical factors of loading and dumping, cycle time, and the number of trains that can be operated and safely controlled. After the size of the train is determined, the type, size, and specifi¬cations of the locomotive can be selected. The loco¬motive may be trolley, battery, or diesel; selection guides are discussed elsewhere in this chapter. The advantages of rail main-line haulage are high tonnage capacity, flexibility, reliability, safety, low operational and maintenance cost, and dual usage of the system (supply haulage, for example). The dis¬advantages are high capital investment, high installation cost, the requirement for more maintenance facilities, and restriction to certain ore reserves and mine pro¬jections. Supply Haulage Supply haulage is a basic requirement of any mine, but the type and volume of supplies vary with the type of mineral being mined, the mining methods, and the size of the mine. A mine developed for rail main¬line haulage gains supply haulage through the addition of a secondary track system to extend the main line closer to the producing areas. Additional haulage equipment, generally smaller, is also added. It is neces¬sary to design into the rail system more switch bypass points and train control systems. The track system standards demanded by rail main-line haulage con¬tribute to the reliability and efficiency of the supply haulage function, whereas a supply track system to supplement other haulage systems often suffers from poorer track and installation standards. When belt conveyors are chosen for production haulage, a rail supply haulage system is often installed rather than using rubber-tired vehicles for supply haul¬age. The conditions of the seam or ore body create these items for consideration: haulage grade of more than 6% favors rubber-tired vehicles; longer haulage distances favor rail; difficulty in maintaining a smooth roadway favors rail; and movement beyond the end of a rail system generally requires rubber-tired vehicles, making a single system rather than a dual system attractive. Although operation of a supply haulage system may be concentrated on a single shift of a multiple-shift mining operation, proper planning and supervision are required if the haulage is to be efficient. Often the newer personnel at a mine are assigned to supply haul¬age which may add to the difficulty of obtaining maxi¬mum efficiency. Supply haulage by rail offers the advantages of high reliability, lower maintenance, and high efficiency over long distances. The disadvantages are less flexibility, high installation costs, and rubber-tired vehicles for use beyond the inby end of track often required. Personnel Movement The efficient and comfortable movement of the miner to and from his work area has a significant effect on his daily output. Minimizing man-trip time also becomes more and more important as hourly wages increase. Personnel are generally moved over a rail system by one of three methods: a specialized personnel carrier to which a certain number of men who work in a certain area are assigned; a combination vehicle, used to carry personnel but also capable of being used as a light supply/utility locomotive during a working shift; and man-trip cars towed by a supply locomotive. The first and second methods are used in coal mines where long distances make speed and comfort important. The third method is more common in metal mines. Equipment Movement As mining equipment technology has advanced, many mining machines and their subcomponents have grown in size. This trend requires careful planning for adding specialized carriers to handle the movement of larger equipment. Continuous miners, longwall equipment, raise borers, and ventilation equipment are examples of machines which may be difficult to move and which require special handling. The selection of the weight, speed, and operating characteristics of supply locomotives used to move equipment is important. Larger mines may often justify a special group of loco¬motives for this application.

Jan 1, 1982

By David Court, Rab Brown

The paper discusses the work in progress on the construction of the extension of the High Speed Rail line from the Channel Tunnel into the centre of London UK known as the “Channel Tunnel Rail Link” (CTRL), and particularly on contract 250 which involves the construction of two 5.3Km tunnels 7.15m diameter constructed with two EPB convertible tunnelling machines underneath the densely populated area of East London. In addition the paper will look at an innovative Alliance that has been formed between the Contractors and the Client’s Engineer involved in the construction of the London Tunnel Contracts

Jan 1, 2003

By Maurice Grieves

GC. Waterman Mr. Grieves' paper on "Shaft Sinking Today--A Boring Business Tomorrow" in the Dec. 1981 issue of MINING ENGINEERING is an excellent description of recent improvements in speed and costs of shaft sinking. However, shaft boring techniques are not a recent development. In 1935-36, the Idaho Maryland Co. (gold), Grass Valley, CA, bored the vertical 1.5-m-diam Idaho No. 2 ventilation and supply shaft to a depth of 346 m. The equipment was designed and perfected by Branner Newsome and was, I believe, described in "Transactions." Pickands Mather later bored a 1.8-m-diam shaft to a depth of about 305 m using Newsome's design. The Idaho No. 2 shaft cut through hard gabbro, diabase dikes, soft serpentine, very incompetent ankeritized serpentine and a strong fault zone. The completed shaft did not require timber support; the fault zone was cemented. Equipment consisted of a rotating 1.5-m or 3-m core barrel with a slotted bottom which cut a 76-mm kerf. The cutting agent was chilled steel shot introduced into the slot as needed. The driving mechanism and core barrel were lowered into the shaft, the former secured to the wall and the inshaft "engineer" operated the motors which controlled core barrel rpm and advance. After an advance of 1.5-3 m the equipment was lifted out of the shaft, a half(?) stick of powder cut off the drilled core, and it was hoisted to the surface with a cable attached to an eye bolt at the tope of the core. A "shift" consisted of three men: hoistman, equipment operator (down the shaft), and a surface laborer. Advance was variable as equipment and techniques were perfected. Near the end of the job advance was, as I remember, 1.5-3 m per shift. Costs were, as I recall, about $115/m. Up to 4 m cores were lifted out in one piece and swung to the dump by a stiff leg derrick. The Newsome equipment was relatively inexpensive to build and operate and his method should be (more than?) competetive with the methods described by Grieves. W.E. Hawes The author, in mentioning the South African developments of the cactus grab, ignores the parallel development of the Cryderman mucker in this hemisphere. Perhaps a slightly longer history of blind hold drilling would have been in order. Blind shaft boring got a major boost at the Nevada Test Site, as part of the nuclear weapons development, when it was essential to be able to quickly assess depth for weapons testing. One of the early civilian attempts to utilize this technology occurred when Kerr McGee drilled the shaft at the Section 19 Mine at Ambrosia Lake, NM. This twin masted drill rig belonged to a subsidiary of Kerr McGee, not Shaft Drillers. This was a difficult hole, due to bentonitic shales that decomposed. Later advances in drilling fluids eliminated this problem. The Conoco project referred to is not entirely correct, and needs minor amplification: The depth of the development (not pilot) shaft drilled was 684 m, at a diameter of 3.05 m, with a 2.16 m ID hydratatic casing being installed to a depth of 669 m. Conoco Inc., not Challenger, executed the drilling, however Conoco did use Challenger Drilling Company's Rig 14-S. Rig 14-S is unique in that it is specifically designed for shaft drilling, rather than being an oil field rig used for this service. All work was planned and directed by Conoco personnel. Deviation of the aforementioned shaft from vertical was 31 cm. Two smaller shafts (pilot shafts) were drilled with the same rig. These smaller ones were drilled 1.8 m in diameter, to depth of 665 m and cased with .91-m-diam casing, to depth of 650 m to be used as pilot holes for 5.5 m diameter shafts. The total elapsed time for all drilling, casing, cementing, and rig moves was 50 weeks. The constraints mentioned of vertical accuracy, torque, wall collapse, rig set up time, lining time etc., pumping out, etc., may not be as serious as the author implies. First, vertical accuracy: The record achieved by Conoco indicates that with reasonable care, good accuracy can be obtained, primarily by having a fair amount of weight in tension, rather than on the drill bit. Second, the amount of torque that can be applied to the drill stem has been greatly increased by the introduction of larger diameter drill stems, such as the new Hughes rig uses. Third, risk of collapse of shaft walls is minimal with the proper mud program. Basically, the walls are supported by the weight of the mud and it is not removed until some type of casing is installed and grouted in. Here in the real challenge of blind drilling shafts to devise a more economical method of lining bored shafts than using steel casing. The remaining issues were minor at Conoco, provided adequate planning and scheduling takes place. An excellent paper, "Shaft Drilling--Crownpoint Project" by Hassell H. Hunter, presented at the Fifth Uranium Symposium in Albuquerque in Sept. 1981 contains details of this project. A combination of blind boring, with enlargement by either mechanical means (boring machine, or tunneling type shield) or slabbing down, with muck removal through a larger bored shaft would seem to be the future trend in shaft development. The economics, especially for wet conditions, favor this concept over conventional sinking, as has been demonstrated at Kerr McGee --Churchrock, UNC--Churchrock and Conoco at Crownpoint.

Jan 3, 1983

By C. K. Man

Coal dust explosions in underground coal mines are prevented by generous application of rock dust (usually limestone). If an explosion should occur, the rock dust disperses, mixes with the coal dust and prevents flame propagation by acting as a thermal inhibitor or heat sink. To investigate this process in more detail, a number of explosion experiments using various coal dust and limestone rock dust mixes have been carried out at the Lake Lynn Experimental Mine (LLEM). These were conducted in a single entry of about 1600 ft (488m) in length and initiated with a methane gas explosion. A consistent set of post-explosion floor dust samples were taken along the entry after each test. These dust samples have been analyzed in the laboratory using thermogravimetric analysis (TGA) and solubility to determine how the limestone rock dust behaved during the coal dust / rock dust explosions. The preliminary results are reported in this paper and indicate that the chemistry of limestone plays an important role in its capacity to inhibit coal dust explosions. The results also show that it may be possible to estimate the intensity of the explosion using these conventional methods of analysis. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Drew Hobert, John Nielson, Erich Dohm

Metallurgical coal is an essential component for the blast furnace-basic oxygen furnace (BF-BOF) steelmaking process, which accounts for roughly 70% of total global steel production. To meet the growing demand for metallurgical coal, Arch Resources identified the potential to recover low- ash coal from ultra-fines discarded prior to the deslime flotation circuit across their portfolio of operations. Historically, many flotation circuits were designed to discard this ultra-fine coal due to high clay content and technological barriers to cost-effectively upgrade and dewater the coal to a saleable product. Recent advancements in high-intensity flotation technology, including the Eriez StackCell, have enabled coal producers to recover ultra-fine coal while minimizing capital and operating costs. In July 2023, Arch Resources commissioned the first full-scale ultra-fines recovery circuit utilizing StackCell high-intensity flotation technology at the Leer Mining Complex. This paper reviews the approach utilized to develop the flotation process design, learnings from the commissioning and ramp-up period, and performance data through the first year of operation.

Feb 1, 2025

By M. Guney, A. R. Bell

In Mindola mine on the Zambian Copperbelt, there is a plan to extend the current production level of 1.2-1.5 km (3,900-4,900 ft) with five additional production levels. Research work indicated that the present total heat output of 38.6 MW will inevitably increase to 63.2 MW in 25 years. Estimated WB and DB temperatures, representing the total heat generation in stope faces and development headings during these same periods are predicted to increase to 33.8/40.2°C (93/104°F) and 35.3142.10C (95/108°F) respectively. It is assessed that the nominal refrigeration capacity needs to be progressively increased to 9, 000 MW.

Jan 3, 1984