Search Documents

By B. McFadzean, M. Becker, S Geldenhuys, A. Molifie

Mineral hydration is known to result in low flotation recoveries and grades within primary platinum group element ores worldwide. This is because the phyllosilicate minerals derived from hydration reactions of silicate minerals (i) form electrostatic coatings on valuable minerals that in turn hinder collector adsorption, (ii) alter the viscosity of the slurry leading to poor gas dispersion and (iii) decrease the concentrate grade due to naturally-floating gangue. Sodium silicate was investigated because its dispersant, rheology modifying, and depressant properties could prove promising in combating the problems associated with these ore types. Quantitative evaluation by scanning electron microscopy analysis revealed large quantities of serpentine and talc present within the ore sample used in this study, which led to a poor flotation response as indicated by batch flotation tests. Using sodium silicate improved the recoveries and grades at high dosages (>1000 g/t). The zeta potential experiments indicate that improved recoveries are, in part, as a result of the reversal of serpentine surface charge, creating electrostatic repulsion between serpentine and valuable minerals which prevents the coating of valuable minerals by serpentine slimes. Ore dilution and rheology tests indicated that decreased viscosity at high dosages also improved recoveries. Talc micro-flotation tests revealed that the depression of talc occurred at higher sodium silicate dosages, which improved concentrate grade. The processing of nearsurface altered ores is becoming an increasing problem worldwide and the use of sodium silicate proved valuable in mitigating the problems associated with the altered ore investigated in this study. Keywords: Alteration, phyllosilicate slimes, colloidal chemistry

Jan 1, 2020

By D. J. Stanton

The objective of this study was to develop, install, and test a small underground mobile refrigeration plant (MRP) to deal with some of the real problems associated with mine cooling in an operating mine. The requirement for cooling the underground environment is discussed with particular emphasis on the need for this method of cooling, with the concomitant benefits. The research investigated current methods of cooling and reasons for previous failures in MRP. Both static and dynamic simulations were conducted to increase the confidence level under operating conditions. Implementation and testing, resulted in ?lessons learnt? requiring modifications, which are documented. Actual results have been recorded. These results have proved that significant cooling via MRP is feasible. Main benefits include positional efficiency, cost per kilowatt of cooling and cooling opportunities for remote hot areas of a mine. Finally, a proven technology is now available for large-scale implementation in the mining industry. Now the ventilation engineer has another system of cooling, which can be utilized in the quest to create an occupational environment, which meets the physical and mental health requirements of the worker.

Jan 1, 2004

By B. Orgilbayar, B. Unursaikhan, S. Sukhbat, Ts. Zagarzusem, D. Baasanjav, L. Jargalsaikhan, E. Otgonjargal, N. Sugir-Erdene, Ts. Soyolmaa

This study has investigated the efficacy of the gravity beneficiation method based on gravitation and centrifugal forces for manganese ore. Powdered samples of manganese ores from the Unagad deposit in Mongolia were analysed for their element and mineralogical composition using ICP-MS and X-ray powder diffraction (XRD). The analysis presented the mineralogical compositions of the ores as hydro goethite, manganese minerals and magnetite, gangue minerals as quartz, albite, orthoclase and microcline of manganese ore. Manganese minerals are white in colour and have micro-veinlet, fine grained-aggregates associated with gangue minerals. The most important manganese minerals are hausmannite, pyrolusite, rhodochrosite, and manganosite. The composite of feed containing 17.31 % Mn and 36.3 % SiO2 was processed in a shaking table. In the experiment, a concentrate assaying 41.37% Mn was obtained from this composite with 65% recovery. In another experiment, f80=0.074 mm particle size ore was used in the MGS concentration test. A concentrate containing 38.34 % Mn with 75.2% recovery was produced in this experiment. The results showed that it is possible to obtain concentrate through gravity processing of manganese ore, which is an economically beneficial process for producing a product of a standard requirement. Keywords: Manganese ore, gravity separator, centrifuge, shaking table 1. Introduction

Jan 1, 2020

By J. Witley

"Narrow tabular platinum group element deposits in the Bushveld Complex of South Africa are typically evaluated by diamond core drilling from surface. Several short deflections are drilled from each mother hole in order to obtain multiple intersections at a close spacing (less than 1 m). Examination of the intersections from deflection drilling revealed the importance of these deflections in understanding the representivity of the borehole, obtaining an estimate of the nugget effect, and mitigating the undesirable effect of the high grade variability at the ultra-short range that is a characteristic of these deposits. The use of deflections in estimation was investigated by means of a number of techniques and scenarios in order to find the most appropriate way to use them in an estimate. A significantly improved level of confidence was gained from using multiple close-spaced intersections rather than a single borehole intersection. IntroductionThe Upper Group 2 chromitite layer (UG2 or UG2 Reef) is known for its remarkable geological continuity, being traced almost uninterrupted for tens of kilometres. However, what is often less well emphasized is the high variability in platinum group element (PGE) grade and thickness (and therefore PGE content) and internal reef stratigraphy over very short distances (several metres or even tens of centimetres).This paper examines the application of short drill-hole deflections in evaluating UG2 PGE mineral resources at Marikana in the western Bushveld Complex of South Africa."

Jan 1, 2017

By T. Mahlangu Mahlangu, T. Fungene, K. C. Sole

"Although oxygen is widely employed as the oxidant of choice in gold leaching by cyanide, its low aqueous solubility presents some drawbacks in practical application; hydrogen peroxide has therefore been considered as a possible alternative. The aim of this investigation was to study the catalytic decomposition of hydrogen peroxide, which generates an oxidizing intermediate species, and to understand its effect on cyanide destruction. Operating conditions that facilitated the effective decomposition of hydrogen peroxide were established by varying the pH and catalyst type and concentration. The oxidizing intermediate, detected using an indirect technique, was found to be the hydroxyl radical (OH?). OH? is commonly generated in acidic solutions, but this work demonstrated that it is also produced at the alkaline pH values necessary for cyanide gold leaching. The effects of free and complexed iron and copper catalysts on the oxidation and consumption of hydrogen peroxide and cyanide were also investigated. It was shown that the cyano complexes of Fe(II) and Cu(I) are also effective as decomposition catalysts. Hydrogen peroxide concentrations above 0.01 M decreased the free cyanide concentration, which was attributed to the probable formation of the cyanate anion (CNO-). Although cyanide consumption increased due to its oxidation in the presence of OH?, excessive cyanide consumption in the presence of copper was attributed primarily to its complexation by the unstable copper(I) cyanide species. Rate constants for the decompositions of H2O2 and cyanide by ferrocyanide and copper cyanide were calculated; the latter was identified as being a better catalyst. IntroductionLeaching of gold from its ores using cyanide has been employed for well over a century (Habashi, 2016). Addition of cyanide converts the gold into a cyanide complex (Au(CN)2 -) that is soluble in water (Wang and Forssberg, 1990). The leaching reaction can be represented as Equation [1]:"

Dec 1, 2018

By L. Gunnewiek

An advanced real-time monitoring system called the tapblock diagnostic system (TDS) has been developed. The purpose of the TDS is to help furnace operators manage the safe operation and economical maintenance of furnace tapblocks. This system is an evolution of the current practice of using historical records and operator interpretation to assess the ?health? of a tapblock. The main parameters affecting tapblock health are heat removal capacity and refractory wear, and these are currently difficult to assess in situ except in a global way. By using monitored and operating data together with predictive numerical modelling and multivariate statistical methods, real-time tapblock performance is assessed relative to expected performance. A state indicator in the form of a green, yellow, and red light is used by furnace operators to monitor the tapblock performance and health status during operation. Access to historical operating data and the provision of diagnostic functions allow for probable health degradation events to be deeply investigated. A recent opportunity to evaluate the actual performance of a first generation TDS installed in the KIVCET furnace at Teck Cominco?s Trail Operations showed that a reasonable estimate of tapblock health was made. However, the evaluation also found that some areas of refractory wear were missed, and a new mechanism affecting refractory wear was discovered that was not previously known. This has reinforced the belief that there is a need to develop improved methods of monitoring so that data used to define the health of the tapblock is more comprehensive and accurate.

Jan 1, 2008

By S. Banisi, A. Ghasemi, E. Nematollahi

Discrete element method (DEM) has been used as a popular simulation method to verify designs by visualising how material will flow through complex equipment geometries. Although DEM simulation is a powerful design tool, finding a DEM model which includes real material properties (e.g., shape, cohesion and friction coefficients) is not computationally feasible. In order to obtain more realistic results, particle energy loss due to rolling friction has been highlighted by many researchers. To implement a reverse torque to account for rolling friction, various models have been proposed. On account of the complexity of the problem, there is no unique model for all applications (i.e. dynamic and pseudo-static regimes). In this paper, an in-house developed DEM software (KMPCDEM ©) was used to assess the robustness of three commonly used models by comparing the repose angle of iron ore pellets obtained through the draw down test in a laboratory setup and then the elastic–plastic spring dashpot model was modified based on considering the individual parameters instead of relative parameters of two contact entities. Results showed that the modified model could produce higher repose angle. The modified model was used to calibrate DEM simulation of repose angle of iron ore pellets in a laboratory setup of the draw down test. Comparison of the calibrated DEM simulation and laboratory results showed 2° differences between the predicted and measured angle of repose. This difference was attributed to considering the particle shape effects by assuming a spherical shape for particles. Keywords: DEM, rolling friction,particle shape, repose angle

Jan 1, 2020

By S. Schmachtel

Several possible physico-chemical properties of composite electrodes for oxygen evolution are presented to describe experimental data for which a mathematical model had been developed. On this basis, local electrical and electrochemical properties of a composite electrode were investigated with conductive atomic force microscopy (CAFM) and scanning electrochemical microscopy (SECM). It could be shown by CAFM measurement that the boundary between matrix and catalyst particles seemed to have special advantageous electrical properties. The SECM measurements showed the presence of mass transport phenomena with increased surface concentrations, whilst the thickness of the Nernst diffusion layer was very small. An intermediate was detected and assigned to be hydrogen peroxide. From all species involved in the oxygen evolution reaction (H2O2, H+ and O2), it was concluded that local active spots exist on the electrode on which hydrogen peroxide reacts to oxygen and protons. A two?step two-material process was suggested to explain the whole oxygen evolution mechanism.

Jan 1, 2008

By G. J. de Korte

South Africa is reliant on coal for the generation of almost all the electricity used in the country, and several large industrial concerns such as Sasol are also coal based. Research relating to the mining, beneficiation and utilization of coal is important in order to ensure the optimal exploitation and use of coal within the country. The Fuel Research Institute (FRI) of South Africa was established in 1930 to investigate all aspects of coal beneficiation and utilization in South Africa. The FRI went on to conduct world-class research and in 1957 a pilot coal preparation plant was constructed in Pretoria to enable large-scale practical experimentation. The pilot plant played a pivotal role in the establishment of South Africa?s low ash coal export project. Political and economic factors contributed to the eventual closure of the FRI and South Africa experienced a period of about 10 years between 1990 and 1999 during which very little public coal preparation research was done. This changed for the better towards the end of 1999 when Coaltech 2020, a collaborative research program was established. Participants included the CSIR, universities, the government and the major coal producers. Coal preparation research conducted under Coaltech thus far include dewatering and drying of fine coal, size classification of ultra-fine coal and dense-medium fine coal beneficiation. Currently, the Coaltech focus is on the beneficiation of low-grade coal reserves and is investigating existing as well as new techniques that can be utilized to provide cost-effective beneficiation of low-grade raw coals and reject coals.

Jan 1, 2010

By M. Rudolph, E. Schach

Tecflote is a new group of nitrile-based collectors for sulfide flotation. Water insolubility results in some interesting implications for the actual mechanism. It is not yet understood if Tecflote is directly adsorbed on the mineral surface as emulsion droplets or if it is only active at the air-water interface, affecting the interfacial rheology or electrostatic- and Van der Waals interactions, which have a direct impact on the bubble-particle contact. Different investigations including contact angle measurements, AFM studies and micro-flotation experiments are conducted to obtain a better understanding of the actual mechanism of Tecflote. Due to the reagent’s insoluble character, the Langmuir-Blodgett technique is used to investigate its behaviour in the air-water interface and to deposit defined layers of Tecflote on mineral substrates for the above-mentioned studies. An interferometric set up is used to investigate the influence of Tecflote on the film thinning between an air bubble and a mineral substrate. In addition, possible synergistic effects for the combination of Tecflote and conventional frothers (e.g. MIBC) are studied. Keywords: Sulfide flotation, insoluble collector

Jan 1, 2020

By L. Cortez, Á. Magalhães, F. Durão

Methods based on regionalized variables theory, commonly known as geostatistics, have been widely used since more than three decades to predict/estimate spatial distributed data, namely mineral resources, with quite good results. However, some restrictive theoretical assumptions, such as the need of some kind of stationarity of data and the linearity of the predictor/estimator, are often wrong options in many applications. An alternative approach based on a finite mixture modelling, or cluster weighted modelling (CWM) technique, is presented and compared, in its theoretical and practical aspects, with the geostatistical methodology. CWM is a general non-linear framework based on the estimation of joint density functions allowing the calculation of the conditional probability function of the target values given their locations. Validation tests are performed in a 2D case study, where testing data proceeds from a soil contaminated by a heavy metal. The results of ordinary kriging and CWM estimations show a very good agreement with actual data. Keywords: Non-linear regression, Geostatistics, Ordinary kriging, Finite mixture modelling, Cluster weighted modelling.

Jan 1, 2003

By P. N. Erasmus

This paper considers the fundamental concepts of support design for underground openings in highly stressed ground. It concludes that the conventional deformed reinforcing bar, woven mesh and cable lacing support methods that have been widely used in deep gold mines are quite in appropriate for the support of highly stressed tunnels. The following is suggested as the criterion for adequate dynamic support under rockburst conditions: the energy absorbed by a support unit (yielding through some acceptable limited displacement) should exceed the kinetic energy generated by the mass of rock that is intended to be retained by that unit. Duraset in conjunction with SRK Consulting has developed a yieldable steel tendon called the Durabar®. It is unique in the sense that it cleverly utilizes the property of the ductility of ordinary low-carbon steel from which it is made to accommodate the excessive displacement it is subjected to in the case of rockbursts or swelling ground.

Jan 1, 2009

By M. Verri

The paper describes the design options available for the simultaneous production of liquid sulphur dioxide, via cryogenic condensation, and sulphuric acid in a sulphur-burning sulphuric acid plant. The impact of the operating conditions of the cryogenic condensation on plant capital and operating costs are discussed, with the main focus on the optimization of the most important economic and operative drivers of the non-ferrous mining industry, such as energy efficiency, reliability, and availability. A case history relevant to an integrated sulphurburning plant producing liquid sulphur dioxide and sulphuric acid, recently started up in the Democratic Republic of Congo, is described. Keywords sulphur burning, sulphuric acid, liquid SO2, cryogenic SO2 condensation, liquid sulphur dioxide, sulphur dioxide.

Aug 1, 2013

By A. Koning

Pressure hydrometallurgy operations require vessels to be lined with an impermeable membrane for corrosion protection and one or more courses of refractory or ceramic brick. Examples of unit operations that utilize composite lining systems include pressure oxidation autoclaves, sulphide precipitation autoclaves, chloride leach reactors, flash vessels, cyclone separators, and direct contact condensers (heater vessels and quench vessels). The refractory lining must satisfy multiple requirements: it must thermally insulate the membrane from process fluid, be structurally stable, provide erosion resistance, be chemically compatible with process fluid, and provide an economic service life. New hydrometallurgical processes are pushing the pressure, and temperature with each new generation of plants. A fundamental understanding of all factors affecting the mechanical stability of the lining system is essential as lining designs move further away from the industry?s experience base. The method of designing a refractory lined vessel is examined taking into account the impact of irreversible chemical swell, operating factors, design factors, and installation factors. The effect of geometry and incorporating additional degrees of freedom to the analysis is explored using two-dimensional and three-dimensional finite element analysis (FEA). The effect of these additional degrees of freedom on the results of the one-dimensional model are discussed. Keywords refractory lining design,autoclave, finite element analysis.

Aug 1, 2013

By K. Andres

This paper presents the vibrating mill technology and summarizes the grinding principle of ultra fine grinding. In addition, a variety of operations is described and the benefits of these different operating modes? product size and efficiency are specified. A case study of an industrial application is presented to show the integration of vibrating mills into grinding circuits. The primary focus is the overall process scheme of this technology, the installation and operating costs, as well as the design parameters required for best performance. The vibrating mill can be used in a wide range of applications for process engineering duties. For a wide range of applications, from soft to extremely hard products, which require ultra fine grinding, surface activation or homogenization, the vibrating mill is well proven. Due to its easy operation, versatility and operation efficiency, the PALLA? vibrating mill gains in importance in the mineral processing industry. Keywords: Coal, comminution, grinding, mineral processing

Jan 1, 2010

By J. Petersen, T. Moyo

Waste Printed Circuit Boards (PCBs) are a metals-rich fraction of electronic waste (e-waste) streams, and globally it has been demonstrated that they can be recycled gainfully to recover the metals. Reported successful cases of PCB recycling are carried out in large volumes, using high-level technology and high capital investment smelter house operations. This presents entry barriers for recyclers in developing economies where capital may not be accessible, and the waste volumes are not sufficient to warrant large scale operations. Hydrometallurgical processes have the potential to provide an option for the scalable processing of smaller volumes of PCBs and can be set up at relatively lower capital costs. However, to date, the hydrometallurgical treatment options available rely on precursor communition and classification processes that also require high capital and energy costs. This paper presents an overview of the work done under the Minerals to Metals signature theme towards understanding e-waste recycling processes and developing pre-processing and characterisation of PCBs in order to unlock potential for local end processing in developing economies, using South Africa as a case study. The structure of PCBs is reviewed, and the current size reduction techniques and the subsequent leaching processes are discussed. Keywords: Printed circuit boards (PCBs), PCB structure, pre-treatment, liberation, ammoniacal leaching

Jan 1, 2020

By G. P. A. Howe

"A computer model of the rutile, ilmenite and zircon industry was developed jointly by Associated Minerals Consolidated and Consolidated Gold Fields for exploring marketing strategies and making predictions over a ten-year period. The industry is described briefly and the reasons for modelling it and choosing a deterministic approach explained. The economic structure of the model and its level of complexity are discussed. The necessity and techniques for convenient input and clear output, the team composition and the method of work are discussed.The reasons for the choice of FORTRAN, large computers, remote batch terminals and the vital importance of fast turn-round are discussed.Costs in staff time and computing are given, with an assessment of the reasons for the success of the model. The model is used on a regular basis to aid management decisions."

Jan 1, 2014

By J. Kempken, T. Schreiter, R. Degel, H. Schmieden

After a short summary of the historical milestones of the submerged arc furnace, the paper will highlight different applications and their specific smelting furnace requirements in the non-ferrous area. Additionally, aspects of rectangular furnace design and the features of the copper cooling system for the side wall will be emphasized. Finally a state-of-the-art design tool as well as a new invention to improve slag cleaning technology will be featured, which shows great potentials especially for the PGM and copper related industry. Keywords: submerged arc furnaces, aerro alloys, non-ferrous, copper, slag cleaning, PGM, rectangular furnace, DC technology

Jan 1, 2006

By Q. G. Reynolds

The problem of direct-current plasma arc behaviour, interaction, and dynamics is considered in the context of metallurgical DC arc furnace applications. Particular attention is paid to the transient flow behaviour of arc systems. A mathematical formulation of the physics used to describe the arc system is presented, and includes the spatial and temporal evolution of fluid flow, heat transfer, and electromagnetism. Based on this formulation, a numerical model is developed using a finite difference approach on a regular cartesian grid in both two and three dimensions, with a special focus on robust stability, high resolution modelling, and high performance. A collection of results produced using the numerical model to study pilot plant-scale furnaces is then presented. These address a range of process and design variables and their effect on the numerical model?s results. Where possible, the qualitative behaviour of the model is compared to available experimental data. A number of novel effects and phenomena are seen in the dynamic behaviour of the DC plasma arc model for both single and multiple arc systems, which may lead to improved understanding, control, and manipulation of such systems where they occur in industrial applications. Keywords Pyrometallurgy, direct-current furnace, plasma arc, modelling.

Jan 1, 2010

By Q. Zhang, X. C. Wang, S. Mao

Phosphate ore is an important strategic mineral resource in which apatite is the main valuable mineral. Flotation is the most commonly used method to separate apatite from middle-low grade phosphate rock. Selective flotation separation is based on the difference of physical and chemical properties of minerals occurring at the three interfaces of mineral/bubble/water. Surface and interface chemistry of mineral have been playing an important role in interpreting and governing its flotation phenomenon. In-situ, visualized and high-precision analytical techniques, such as Time-of-Flight Secondary Ion Mass Spectrometry, Atomic Force Microscopy and Molecular Simulation, have been applied to explore and uncover microscopic nature of apatite flotation. Consequently, a great progress at molecular or atomic level on surface and interface chemistry of apatite flotation has achieved in the past decades. In this paper, the research progress of surface and interface chemistry of apatite flotation such as surface wettability, surface-charging characteristics, surface dissolution behavior, adsorption mechanisms of fatty acid collector and depressor on apatite surface were systematically reviewed. This review will be helpful for the development of more selective reagents and efficient technologies for apatite flotation. Keywords: Apatite, Flotation, Surface and interface chemistry, Surface analysis technology

Jan 1, 2020