Search Documents

By Y. J. Cao

The purpose of this study was to investigate the flotation behaviour of unburned carbon in a cyclonic-static microbubble flotation column (FCSMC). The ash sample, collected from a power station in Guangdong province of China, was characterized by size analysis, X-ray diffraction, contact angle measurements, and X-ray fluorescence. The effect of the column flotation operating variables on the removal of unburned carbon from the fly ash was systematically studied. The feasibility of separating unburned carbon and ash was determined from the removal rate of unburned carbon (RUC) and loss on ignition (LOI). Within the range studied, the optimum diesel oil dosage was 1200 g/t, abies oil dosage was 600 g/t, pulp density was 20 per cent, superficial gas velocity was 1.4 cm/s, and circulating pressure was 0.20 MPa. The results indicate that the FCSMC technique is effective in removing the unburned carbon from the fly ash, which can be attributed to the generation of microbubbles and the continuous cyclonic circulation method. Under the optimized conditions, a cleaning ash with 2.13 per cent LOI and 94.21 per cent RUC was obtained.

Jan 1, 2012

By H. Han, Z. Gao, Y. Gao, W. Sun, J. Wang

Strategic Ca-bearing minerals like scheelite and fluorite are usually separated by flotation, yet the separation is quite difficult due to their similar surface Ca active sites. Compared with the conventional strong collector sodium oleate (NaOL), lead nitrate-benzohydroxamic acid (Pb-BHA), complex collector shows a better selectivity for scheelite, yet its high cost hinders its wide application. Therefore, a novel collector (Pb-BHA-NaOL complex) was initially developed in this work to overcome the abovementioned dilemma. The flotation results of a single mineral showed that Pb-BHA-NaOL had a better selectivity for scheelite than Pb-BHA. Under the conditions of sequential assembly of Pb, BHA and NaOL at the molar ratio of 240:120:1 and pH 9.0, selective separation of scheelite from fluorite could be achieved without adding any depressants. In addition, for the same preferred scheelite recovery, Pb- BHA-NaOL could also save approximately 20% Pb and BHA compared with Pb-BHA. The analyses of the zeta potential measurement and X-ray photoelectron spectroscopy indicated that Pb-BHA-NaOL showed stronger adsorption on scheelite relative to fluorite. Meanwhile, Pb-BHA-NaOL showed more adsorption modes and higher utilisation of Pb and BHA on scheelite than Pb-BHA, which was due to the accelerator, NaOL. Keywords: Scheelite, fluorite, lead nitrate, benzohydroxamic acid, sodium oleate, flotation

Jan 1, 2020

By J. E. Xu, J. Y. Zhang, M. Q. Sheng, K. Wan

"SynopsisThe densities of selected CaO-Al2O3-MgO slag systems were measured at 1823K by the Archimedean method. Thirteen different slag compositions were chosen based on different levels of the MgO content and the mass ratio of CaO/Al2O3. The results indicated that the density of the slag decreases with increasing MgO content (from 0–3.78 mass%), but increases with further increases in MgO content up to 11.33 mass%. At a fixed MgO content of 5.5%, the trend of density change with CaO/Al2O3 in the slag is similar to that for changes in MgO content. On the basis of the regular solution approximation rules of excess molar quantities, an attempt was made to estimate the molar volume of the slags investigated. The application of the molar volume model confirmed that the present expanded approximation rules are applicable to predict the molar volumes of the melts discussed.IntroductionDensity is one of the most important fundamental properties of slags, which influences metallurgicaly phenomena in many ways. Density is sensitive to the nature of the chemical bonds and the species in the melt, and is of great importance not only for theoretical research on the structural properties of molten slags, but also for industrial applications. Density is also required to estimate other key properties used to assess the behaviour of high-temperature molten oxides, e.g. viscosity, surface tension, and thermal conductivity.Liquid calcium aluminate slags that contain magnesia are the basis of most ladle slags for secondary refining processes. The CaO-Al2O3 binary phase diagram (Hallstedt , 1990) shows the eutectic composition (50 wt% CaO and wt% Al2O3) has the lowest melting temperature. The main emphasis of this study is on the 12CaO·7Al2O3 refining slag with MgO additions. The CaO-Al2O3-MgO ternary system is of considerable importance in industrial metallurgical processes, and is fundamental to the understanding of metallurgical slags, ceramic materials, and geological phenomena."

Jan 1, 2015

By N. Naude, R. Foisy, F. Bornman

Spiral separators have been widely accepted as one of the most flexible gravity separation devices for several decades. The International Journal of Mineral Processing, 84, pp. 118 – 132 mentioned that spirals are for treating material too coarse for flotation and too fine for dense-media separation. Powder Technology V 102, pp 244 – 252, 1999 stated that there exists a genuine need for extending the performance envelope of spirals – whether to treat finer or coarser material than the traditional size ranges. In recent times there has been an upsurge in interest, particularly in the development of newer fine gravity separators. Spiral separators for the recovery of ultra-fine particles have a unique profile, pitch and features to ensure efficient performance. The flow on the spiral trough must be controlled to minimise turbulence that will entrain fine particles in the outer section of the trough. The experimental test work showed a movement of mass from the outer region towards the centre column of the spiral, i.e., from the fine tailings band towards the concentrate. As recovery on the spiral trough is a function of mass yield and grade, the ultra-fine 7 spiral had a better recovery than the HX5. This makes the UF7 an ideal rougher spiral. Keywords: Ultra-fine particles, spiral, design, recovery

Jan 1, 2020

By M. Saghaeian, R. Hejazi, V. Sheikhzadeha, A. H. Baladastian, A. Dehghani Ahmadabadi

This paper describes research done to remove apatite (phosphorus) from hematite ultrafine (70% finer than 25 micron) concentrate, recovered by electromagnetic separators at the FST Tailing Recovery Plant located in Chadormalu Iron Ore Complex through reverse froth flotation. As a result, iron and phosphorus content in magnetic concentrate (flotation feed) were 53.52% and 0.58%, respectively. Therefore, to increase the Fe content and decrease the P content of the sample, reverse flotation tests were applied. Chemical reagents used in this research consisted of sodium silicate as a depressant, sodium hydroxide and sodium carbonate as pH regulators, Alke & Dirol as fatty acid collectors and MIBC as frother. Process parameters including dosages of collectors, depressant and frother, preparation times of depressant and collectors, steps and time of frothing and pH range were selected. After doing flotation tests, in optimum condition, dosages of collectors were 1200 g/t, depressant 1200 g/t, pH in the range of 9.5 to 10, preparation time of collectors in the first step was eight minutes and at the other steps, four minutes; the number of frothing steps 4 and frothing time in each stage was three minutes. In this case, it was observed that the amount of phosphorus in the final concentrate was reduced to 0.05%, the Fe content increased from 53.52% to 61.66% and the Fe recovery achieved was 82.21%. Keywords: Iron ore, hematite ultrafine concentrate, iron and phosphorus content

Jan 1, 2020

By U. Atici, R. Comakli

"Understanding rock properties is of vital importance in mining and civil engineering. Rock properties are generally determined through laboratory tests, which require a large number of uniformly shaped samples and technicians who use indirect methods to determine rock properties. The texture coefficient (TC), which represents various textural parameters including the size, shape, orientation, and relative proportions of grains and the matrix, is an efficient means for indirectly evaluating the mechanical behaviour of rocks. In this study, 12 different rocks (ten granites, one diorite, and one gabbro) were collected and their engineering properties. including specific gravity, porosity, P- and S-wave velocities, Schmidt rebound hardness, uniaxial compressive strength, and elasticity modulus, were investigated. Relationships between TC and these measured properties were assessed. Statistically significant (at the 95% confidence level) correlations were found between the TC and compressive strength, elasticity modulus, sound velocity (both compression and shear waves for dry and saturated samples), but no significant correlation was found with Schmidt rebound hardness. The results suggest that it is possible to use the relationships between TC and the mechanical properties of rocks in rock classification. IntroductionIn every aspect of rock engineering, knowing rock properties is essential for determining and predicting the behaviour of rocks and rock masses. Mechanical properties of rocks are important parameters in mining, geology, and engineering, and they are affected by textural characteristics such as grain size, grain shape, cement type, degree of cementation, mineral content, and the ratio of the grain area to the matrix area. The effects of textural properties on the physical and mechanical properties of rocks have been investigated for a long time, and previous studies revealed close relationships between single parameters related to rock texture and mechanical properties of rocks (Akesson et al. 2001; Gunsallus and Kulhawy 1984; Merriam, Rieke, and Kim, 1970: Onodera and Kumara 1980; Prikryl 2006; Ulusay, Tureli, and Bider, 1994; Tugrul and Zarif 1998). Rock properties are usually determined using mechanical tests, which require uniformly shaped and relatively large samples. However, it is not always possible to obtain such samples. Furthermore, rocks with similar textural and structural properties may exhibit different mechanical behaviour. Howarth and Rowlands (1987) developed a texture coefficient (TC) that expresses all the main textural parameters of a rock in a single dimensionless quantity based primarily on statistical assessment. The TC makes it possible to understand the effects of a rock’s textural properties on its mechanical properties using thin sections instead of large, uniform samples. Ersoy and Waller (1995) investigated the relationship between strength and TC for limestone, sandstone, and siltstone; they also examined the effect of rock properties and TC on drilling performance. Ozturk, Nasuf, and Bilgin (2004) explored the relationship between rock quality and TC by evaluating the uniaxial compressive strength (UCS) values of limestone, basaltic andesite, and tuff. Gupta and Sharma (2012) evaluated TCs as well as the petrophysical and mechanical properties of quartzite from the lower and higher Himalayas and found a strong relationship between TC and UCS. Similarly, Ozcelik, Bayram, and Yasitli (2013) investigated the relationship between TC and various parameters in marble by applying the statistical analyses developed by Ozturk, Nasuf, and Kahraman (2014)."

Jan 1, 2019

By Y. Belloa, C. Dorfling

The presence of impurities such as Se and Te in copper sulfate leach solutions can have a detrimental effect on electrowinning efficiency. These elements can be removed from the solution by precipitation; sulfurous acid is commonly used as a precipitation reagent, while studies have also reported improved precipitation with the addition of metallic copper. This paper aimed to determine the effect of conditions used during the solution purification step on the characteristics of the precipitates that formed. Precipitation tests were performed in a batch reactor with copper sulfate leach solutions obtained from the base metal refinery of a platinum group metal producer. The effects of agitation rate (250 and 500 rpm), SO2 flow rate (4.4 and 5.8 mL/min.L), temperature (65 and 95°C) and metallic copper powder addition (0, 1 and 2 g/L) on the characteristics of the precipitates formed during the tests were determined using scanning electron microscopy. The major phases detected in the precipitates formed when using SO2 as the only precipitation reagent were elemental Se and Cu2Se. The introduction of copper powder led to the production of different sulfide phases for the experiments conducted at 65°C irrespective of the values of the other reaction parameters. At 95°C, Cu crystals, Cu2O and tiny inclusions of Cu2(Se,Te) were the prominent phases noticed in the precipitates produced from all the tests conducted with copper powder as precipitation enhancing reagent. Keywords: copper, precipitation, selenium, tellurium

Jan 1, 2020

By A. Rahmanab, A. Torpy, M. I. Pownceby, M. N. Zaman, N. Haque, W. Bruckard, J. Tardio

Ilmenite is the principal feedstock for producing TiO2 - used in paints, plastics and paper and the production of Ti metal. The Brahmaputra River system in Bangladesh represents a potentially new source of ilmenite concentrated within sandbar placer deposits and the current study presents results from beneficiation and characterisation studies conducted on Brahmaputra River Fe-Ti oxides. Characteristic of fluvial systems, the ilmenite concentration is low (~0.5 wt-%), however extensive annual dredging for waterway navigation provides the economic impetus to recover saleable ilmenite. The Fe-Ti oxide suite derived from magnetic fractionation comprises homogeneous ilmenite, titanohematite and hematite, although many grains exhibit complex exsolution within the (Ilm-Hem)ss series. The textural variability results in difficulty generating a pure ilmenite feedstock with the bulk concentrate typically being low in TiO2, containing 31.0 wt-%TiO2 and 62.7 wt-% (Fe2O3). Results are interpreted via an analysis of the implications for producing a commercial-grade ilmenite concentrate suitable for TiO2 production. Keywords: Ilmenite, titanohematite, Fe-Ti oxide exsolution, TiO2 production

Jan 1, 2020

By R. Weber

Methane explosions in underground coal mines are a major concern across the mining industry. After the Pike River disaster, Arnot Coal became even more aware of the explosion risk. To determine whether Arnot has adequate precautions against a methane explosion, such as the one that led to the Pike River disaster, a literature survey covering the causes of the incident and what preventative measures should have been in place was conducted. Many different methane explosion prevention methods were evaluated, as well as codes of practice. Based on the findings, Arnot?s measures to prevent conditions favourable for a methane explosion were evaluated.

Jan 1, 2014

By J. P. Garnier, T. Bhambhani, J. A. Garcia, N. Renaud

Most flotation plants use a static reagent scheme, i.e., a set combination of collectors, frothers, and modifiers. This scheme is usually developed and refined over time to deliver optimal (not necessarily the highest) performance when the major ore types are fed to the plant. However, when ore types or mineralogy coming to the plant change substantially (and this often happens as different areas of the pit(s) are mined and crushed at the same time), there are upsets in the process, typically leading to lower recoveries. Adapting to this variability is usually done only when performance drastically suffers, and the changes made may be too late and bring additional variability in performance. The premise for SmartFloat™ is that the reagent suite needs to be dynamic, adapting continuously to changes in the ore and operating conditions. Solvay has combined advanced analytics and data science techniques with its expertise in flotation reagent chemistry to systematically and automatically achieve the above, and in real time. Thus, SmartFloat™ is optimizing the reagent suite continuously, removing the additional variability created by belated human interactions resulting in a better and more stable process. In addition, this advanced approach allows for continuous improvement by identifying poor performing ore domains and improving the reagent suite using Solvay’s FM-100 approach to design appropriate solutions.

Jan 1, 2023

By M. Asghari, R. Amiri, A. Haratian, S. Haji

The aim of this investigation is the evaluation of optimising the Shahroud copper ore beneficiation plant near the Iranian city of Shahroud, by means of a sensor-based ore sorter applying X-ray transmission technology. Currently, this plant’s feed capacity of 52t/h produces 0.5t/h copper concentrate with a grade of 30% and copper recovery of 85% from a feed grade of 0.36%. By applying an X-ray transmission-based (XRT) sorter, it is possible to preconcentrate the feed and remove the gangue materials before entering the plant, enabling the production rate of concentrate to be increased. In this study, the obtained representative sample from the plant was preconcentrated in particle size of - 75+10mm by using the X-ray sorter, thus the concentrate with Cu grade of 0.85% was obtained. Therefore, by using of X-ray sorter the Cu grade of plant feed was increased to 0.48%. By increasing the feed grade from 0.36% to 0.48%, and considering a Cu recovery of 85%, the production rate will be increased from 0.48t/h to 0.61t/h. Therefore, the preconcentration by using the XRT sorter increases the production rate by 27%. Keywords: Optimisation, preconcentration, copper, X-ray, sensor-based ore sorting

Jan 1, 2020

By J. Botha

There are many underground mining software tools available to plan and schedule the development of underground mines. A shortfall of these tools is the optimization of the underground equipment and strategy in order to maximize the development rate. This paper will illustrate how the SimMine® software was used to maximize underground development at Petra Diamonds' Cullinan Diamond Mine. It will also determine the effect of various development strategies and equipment capacities on the underground development rate and pinpoint potential bottlenecks in the mine development cycle.

Jan 1, 2010

By O. I. Rychkova, M. N. Sycheva, E. V. Poryadochnova, G. V. Sedelnikova

Deposits of copper-porphyry type occupy a leading position in the mineral resource base of the world copper industry. They are characterized by large and gigantic scales, often complex composition, their development is carried out in an open way. The raw material base of the Russian copper industry is mainly sulfide copper-Nickel and copper-pyrite ores. Exploration of copper-porphyry deposits and the creation of long-term large mining facilities on their basis is one of the most promising and priority tasks for the Russian industry. This task is especially acute for the copper enterprises of the Urals in connection with the depletion of copper - pyrite ore reserves. In recent years, Russia has carried out a large complex of studies on the composition and technology of processing of copper-porphyry ores of different subtypes. In this work the complex poor copper-molybdenum-gold ore of one of the deposits is investigated. The chemical and mineral composition of the ore containing 0.49% copper, 0.020% molybdenum, 0.39 g/t gold, 5.85 g/t silver was determined. The forms of finding metals and their distribution by size classes are established. The dependence of extraction of metals into concentrates of collective-selective flotation on the size of ore grinding, pH of the medium, reagent consumption is shown. Under optimal flotation conditions, copper concentrate with 18.6% copper content and 92.32% extraction and molybdenum concentrate with 21.5% molybdenum content and 73.4% extraction were obtained. With a high concentration of molybdenum in selective flotation products, it is possible to conclude about the expected molybdenum concentrate with a content of 45% and a recovery of 70%. The associated extraction of gold and silver into copper concentrate is 76.8 % and 73.4%. Keywords: Collective-selective flotation, copper, molybdenum, porphyry ore, grinding, pH, reagents

Jan 1, 2020

By G. D. Rosales, P. F. A. Braga, S. C. A. França, C. P. Pinto

The growing market demand for lithium is mainly due to its use in the manufacture of batteries for electric or hybrid vehicles and portable equipment (smartphones, tablets, power tools, notebooks, etc.). Currently there is great interest in finding new sources of lithium and technologies for its utilisation. Li-S batteries have received attention due to their theoretically high specific energy density, which is 3 to 5 times greater than that of Li-ion batteries. Unlike Li-ion batteries, of which the main raw materials are lithium carbonate and lithium hydroxide, the main raw material for Li-S batteries is lithium chloride. The anode used in Li-S batteries is metallic lithium, produced by a molten lithium chloride electrolysis process. The extraction of lithium from pegmatites such as spodumene, previously abandoned in the 1990s for being uneconomical, has become attractive due to the increase in prices as well as the need for greater lithium purity of products made from lithium-bearing minerals. The main methods used for lithium recovery from spodumene ore include the sulfuric acid process, the alkaline process (lime or limestone as raw material) and the chlorination roasting process. Thermodynamic modelling using HSC software 5.1 was conducted to predict different reactions that could occur during chlorination roasting of the spodumene/MgCl2+CaCl2 system. Lithium extraction from the solid obtained after the chlorination roasting was also investigated. The results of thermodynamic analysis provided a better understanding of the chlorination roasting process for lithium extraction. Metallurgical tests with a mass ratio of 1:6 (spodumene:chlorides) and molar ratio of 2:1 (MgCl2:CaCl2) allowed over 95% recovery of the lithium contained in the spodumene concentrate. Keywords: Spodumene, lithium chloride, chlorination roasting

Jan 1, 2020

By N. X. Feng, S. G. Zhou, X. L. Wu, J. P. Peng, Y. Z. Di

"Szaibelyite–suanite type ore is rich in magnesium oxide and boron oxide. We propose a new method to extract both metallic magnesium and valuable residues rich in boron by reduction using metallic aluminium.Thermodynamic analysis of the reactions between aluminum and MgO, Mg2B2O5, and Mg3B2O6 was carried out. The effects of CaF2 addition, temperature, mass of Al, and pellet formation pressure on the extraction of magnesium were also investigated experimentally.The results indicate that the magnesium oxide phase can be displaced from 2MgO-B2O3 and 3MgO·B2O3 by CaO in the reduction system. The reduction ratio of magnesium oxide was 38% without calcium fluoride addition, increasing to 94% with 5.1% calcium fluoride. The reduction ratio increased with increasing temperature and mass of Al. To obtain a higher reduction ratio, the reduction pellet should be formed under a reasonable pressure.IntroductionBoron and its compounds are widely used in textiles, borosilicate glass, metallurgy, fertilizers, and nuclear shielding. Boron resources are mainly found in Turkey, the USA, Russia, and China. In Liaoning, China, there are abundant szaibelyite–suanite type ores that are rich in magnesium oxide and boron oxide. Szaibelyite and suanite ores are used to produce borax by a carbon dioxide– soda process. Annually, 2 Mt of waste materials containing 3–20% B2O3 and 2–25% MgO are produced during the process. It is necessary to make use of these waste materials containing high concentrations of boron oxide and magnesium oxide to avoid environmental problems as well as for economic reasons (Ozdemir and K1pcak, 2007)"

Jan 1, 2016

NOTICES PROCEEDINGS OF THE SECOND INTERNATIONAL CLEAN AIR CONGRESSThis massive volume of 1,380 pages contains all the papers presented at the congress held in December 1971. INDEX TO SOUTH AFRICAN PERIODICALS This bibliographical work has been produced by the Johannesburg Public Library since 1945, and is of interest to all our readers. THE CONTROL OF GASEOUS SULPHUR COMPOUND EMISSION An international conference on this theme will be held at the Salford University from 10th to 12th April, 1973. COLLOQUIUM ON SLlMES DAMS The South African Institute of Mining and Metallurgy have great pleasure in advising members that two-day colloquium on Slimes Dams is being arranged for the 14th and 15th November, 1973. NATIONAL INSTITUTE FOR METALLURGY / NASIONALE INSTITUUT VIR METALLURGIE REPORT. VERSLAG No. 1424 REVIEW OF THE WORLD'S FLUORSPAR INDUSTRY, WITH PARTICULAR REFERENCE. TO SOUTH AFRICA Ist August, 19n Investigator: H. H. Gossling SYNOPSIS The consumption of fluorspar has increased significantly during the last three years, and a consumption of approximately 5,76 million tonnes per annum is projected for 1975. REPORT. VERSLAG No. 1432 LABORATORY METHOD No. 44/2 THE DETERMINATION OF RUTHENIUM AND OSMIUM IN THE RESIDUES RESULTING FROM THE LEACHING OF MATTES 5th July, 19n Investigators: Magdalena M. KrUger R. V. D. Robert SYNOPSIS The method described involves the sintering of the residue with barium peroxide, and the distillation of ruthenium and osmium from the sinter. REPORT. VERSLAG No. 1439 THE REACTION OF SULPHIDE MINERALS WITH THIOL COMPOUNDS 29th June, 19n Investigator: L. A. Goold SYNOPSIS A selected group of thiol reagents was reacted with a wide range of sulphide minerals, and products that were formed at the surface were extracted and identified by infrared spectrophotometry.

Alexander Sutulov. Mineria Ghilena 1545-1975 (Mining in Chile 1545-1975). Santiago, Centre of Investigation of Mining and Metallurgy, 260 pp. (In Spanish). G. B. Rothenburg. Speciality steels. D.S.A., Noyes Data Corp., 1977. 270 pp. Witbank Middelburg Branch A General Meeting was held at the Wit bank Golf Club on 20th April, 1977, at 17h30. Treatment of waste water An International Research Symposium on New Processes of Waste Water Treatment and Recovery is to be held in London from 6th to 8th September, 1977. It NIM reports Report no. 1708 An examination of the suitability of various reducing agents for the production of ferrochromium. (27th Feb., 1975; re-issued May 1977). Report no. 1724 The preparation and reduction of chrornite pellets containing a reducing agent. (14th Apr., 1975; re-issued Mar. 1977). Report no. 1854 The interaction of pyrite, oxygen, and xanthate. (8th Mar., 1977). Report no. 1876 The ultrasonic determination of the mud level in a thickener and the resin level in an ion-exchange column. (6th May, 1977). Report no. 1878 The electrochemical dissolution of galena in aqueous solutions. (5th May, 1977). Report no. 1881 n-Octylaniline, a new extractant for noble metals.(28th Mar., 1977). Report no. 1883 The determination of iron, chromium, titanium, and tungsten by X-ray-fluorescence spectrometry. (31st Mar., 1977). Report no. 1889 Entropy relations in the formation of complexes of silver (1), mercury (II), and cadmium (II) with llwnodentate liyaruls. (5th May, 1977). Mechanics of granular materials A conference on the above subject is to be held in London on 8th and 9th September, 1977, under the auspices of the Institute of Mathematics and Its Applications.

Jan 1, 1977

By Y. Tanaka, H. Miki, Y. Aoki, H. Okamoto, G. P. W. Suyantar, T. Hirajima

Due to environmental limitations and the scarcity of freshwater, flotation using seawater or desalinated seawater as process water becomes more common for mining operations. On the other hand, seawater has been reported to affect the flotation behavior of sulfide minerals. Few reports are available on influence of pyrite depression, recycled seawater and lime consumption on flotation by using seawater. In this study, the flotation tests were performed using ore sample to investigate the effect of pH with seawater and process water used in plant on the flotation behavior in a laboratory-scale flotation cell and a pilot plant-scale. The results of laboratory scale flotation indicated that copper and molybdenum flotation kinetics decreased with increasing pH. Furthermore, the iron (mainly pyrite) recovery decreased with increasing pH. The pilot plant-scale flotation test showed that water with a higher concentration of magnesium and calcium (plant processes water) consumed a higher amount of lime. Because of low lime consumption and high copper and molybdenum recovery and grade, pH 8 is suitable compared with pH 8.5 for flotation. Keywords: seawater, process water, copper-molybdenum rougher flotation, pH, pilot test

Jan 1, 2020

By H. Laitala, M. Lampi

Metso Outotec has developed a wide range of solvent-extraction technologies over decades and has introduced Metso Outotec VSF®X solvent-extraction plant. Standardized and modularized, Metso Outotec VSFX Plant provides a novel way to design, manufacture, transport, install, operate, and maintain solvent-extraction plants far better than in the past with highly sustainable and safe methods. For the customer, this means fast-track projects with savings in means of time, costs, quality, and operation. Sicomines and Metso Outotec have together implemented and commissioned a modern and efficient copper solvent-extraction plant. Plant commissioning and ramp up of the plant were fast and the plant is now operating efficiently. This paper presents Sicomines’ VSFX copper solvent-extraction project and gives a sight into operating figures for the plant.

Jan 1, 2023

By Y. Ren, B. Yang

The magnetic field characteristics due to electromagnetic stirring in the secondary cooling zone of an extra-thick slab during continuous casting are numerically determined using Maxwell's equations, with particular emphasis on the distribution of magnetic induction intensity and electromagnetic force, as well as the influence of process parameters on the magnetic field. The orientation of the electromagnetic force is the same when the electromagnetic stirrers at the 30° and 60° posistions of the arc-shaped slab are powered in the same direction; otherwise, the orientation is opposite. The magnetic induction at the centre of the section of the stirrer's central axis at the 30° positio, as well as the current, frequency, and fitting formulae, are as follows: B = {0.075I.(1/A)-0.3} mT and B = {-1.75f.(1/Hz)+22} mT. The electromagnetic force and current fitting formula at the central point of the B-B section is F = {0.03168I2.(1/A2)-03.762I.(1/A)+326.7} N/m3, and the fitting formula of electromagnetic force and frequency at the centre point is divided into two segments. The first takes the form of a parabola: = {-21((f-4.3).(1/Hz)2)+970} N/m3, and the second segment is negative linear: F = {-1.65f.(1/Hz)+51.5} N/m3.

Apr 16, 2024