Search Documents

By P. van der Steen

This paper examines the historical developments in diamond beneficiation technology and the impacts on the industry. The art of diamond beneficiation has given way to the application of scientific process, but at considerable capital expenditure. The shift in beneficiation methodologies has been disruptive to the traditional skills set of the industry, but evolutionary change continues and has been beneficial to the quality of the final product.

Jan 1, 2010

By M. H. Dehghanpoor, M. Zivdar, M. Torabi

"A hydrometallurgical route was developed to extract metals such as gold, silver, copper, and selenium from anode slime from Sarcheshmeh Copper Complex in Iran. For the extraction of copper by leaching, the anode slime was heated and stirred with 4 M sulphuric acid in the presence of oxygen. Optimal conditions for recovery of copper were temperature 80°C, mixing time 5 hours, and oxygen flow rate 2 L/min, resulting in a copper recovery of 94.47%. Silver and selenium were dissolved by leaching anode slime from which the copper had been removed with nitric acid. For gold extraction, anode slime was heated with aqua regia at 90°, and the gold then extracted with 2-ethyl-hexanol at a concentration of 0.5 M and phase ratio of 4. The extract was then stripped with soda solution at pH=10.5 and a phase ratio of 5. Finally, gold was recovered by precipitation with oxalic acid at a ratio of mass to volume 10 g/L. Total gold recovery was 80%. IntroductionDuring the electrorefining of copper, some metals are accumulated in the byproduct anode slime, which is an important source for recycling and recovery of these metals (Petkova, 1994). In this paper, a hydrometallurgical route is described for the recovery of precious metals from copper anode slime of Sarcheshmeh Copper Complex, which is located in southeastern Iran .Copper anode slime is black or gray powder with a particle size less than 200 mesh. Approximately 2 to 20 kg of anode slime is produced per ton of copper cathode. The slime is characterized by higher amount of Ag, Se, Pb, and Cu compared to other metals and a very low Au content (Khaleghi and Ghader, 2013).The copper anode slimes are composed of 11.69% selenium, 3.93% copper, 5.26% silver, 0.13% gold, and 45% barite, plus lead, tellurium, antimony, sulphur, and silica with small amounts of nickel, iron, zinc, and bismuth. Gold is one of the most important noble metals due to its wide applications in industry and economic importance, so recovery of gold from slime is more appealing than that of other metals. According to the World Gold Council (2013), the demand for gold has increased during the last decade. This increase is due not only to the increasing demands of the jewellery market, but also to the increasing demand for gold in industrial as well as medical applications (Ranjbar et al., 2014)."

Jan 1, 2016

By S. Mohanta, B. C. Melkap

"SynopsisDry beneficiation of coal by air dense medium fluidized bed is an emerging trend. It is widely believed that the particle size of the medium has a significant effect on the separation efficiency. This investigation demonstrates that medium particle size has a major effect on separation efficiency. Experimental results show that different size fractions of the same feed respond differently to the same size fraction of medium solids. Furthermore, a particular size fraction of feed coal responds differently with different size fractions of medium solids. The Ep values and overall metallurgical performance parameters, obtained from experimental results, clearly indicate the superior performance of an air dense medium fluidized bed separator when using –150+106 µm magnetite powder as the fluidizing medium. These observations reinforce the importance of sizing the medium particle size for the air dense medium fluidized bed.IntroductionIn an air dense medium fluidized bed (ADMFB), a fluidizing bed of a particular density is created by suspending solid particles in an upward air flow. A feed containing coal particles of different densities is introduced into this fluidizing bed. The particles with relative density less than the bed density float on the top of the bed, while particles denser than the bed density sink through it. Since there is a general correlation between ash content and density of coal particles, it is possible to remove ash-forming impurities from a raw coal to the required level by regulating the density of the fluidizing bed. Recently, the ADMFB process has received significant attention world-wide for its specific advantages of low operating cost and less restrictive for small capacities (Luo and Chen, 2001; Houwelingen and de Jong, 2004; Dwari and Hanumantha Rao, 2007; Sahu et al., 2009; Mohanta et al., 2012). This process is not recognized as a well-established industrial practice because of the availability of efficient wet processing technology. However, with the revival of interest in dry beneficiation of coal in general, and ADMFB in particular, there is a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have made the process a competitive and viable option for beneficiating coal."

Jan 1, 2015

By Mark Dangerfield

[Power-Point Presentation]

Jan 1, 2005

By E. C. de Beer

"SynopsisA number of important areas in nuclear fuel cycle, at both the front end and back end, offer ideal opportunities for the application of non-destructive evaluation techniques. These techniques do not only provide opportunities for non-invasive testing of e.g. irradiated materials, but also play an important role in the development of new materials in the nuclear sector. The advantage of penetrating radiation used as probe in the investigation and testing of nuclear materials makes X-ray and neutron radiography (2D) and tomography (3D) suitable for various applications in the total nuclear fuel cycle. The unique and different interaction modes of the two radiation probes with materials provide several opportunities. Their complementary nature and non-destructive character makes them most suitable for nuclear material analyses, analytical method development, and the evaluation of the performance of existing nuclear material compositions. This article gives an overview of the X-ray and neutron radiography/tomography applications in the field of nuclear material testing, and highlights a few of the success stories. Several selected areas of application in the nuclear fuel cycle are discussed to illustrate the complementary nature of these techniques as applied to nuclear materials.IntroductionDuring the development of new materials for the nuclear industry, materials testing and characterization are of the outmost importance to maintain safety standards and reliability. No compromise on safety in the workplace in any area within the total nuclear fuel cycle can be tolerated, and therefore most in-situ material characterization and testing is conducted by certified and qualified personnel schooled in destructive and non-destructive testing (DT and NDT) methods. Certification and qualification in NDT can be obtained through many training centres in South Africa in accordance with European, American, and other international standards (SGS, n.d.; SAIW, n.d.; African NTD Centre, n.d.)."

Jan 1, 2015

By K. Wu, X. Yuan, R. Du, C. Chao

"Lump coals are currently employed to replace part of coke in the COREX melter-gasifier for ironmaking. In order to optimize the process, the pyrolysis kinetics of Datong coal used in the COREX process was studied. A sectioning method is proposed to overcome certain shortcomings of traditional methods for studying the pyrolysis of coal. Based on the sectioning method and the characteristics of the coal pyrolysis process, the temperature range was divided into three intervals. In the first, the adsorbed gas and water of crystallization were removed; in the second, the coal was transformed into semi-coke; and finally, the semi-coke was further coked. Three models of reaction were then established to study the different stages of the pyrolysis process: an interfacial chemical reaction model, a random pore model, and internal diffusion with shrinking volume. The results showed that the experimental data fitted the models well, with all correlation coefficients (r2) exceeding 0.97. Finally, the mechanisms of reaction and kinetic parameters for each temperature range were derived, which laid a necessary foundation for optimizing the usage of non-coking coal in the COREX process. IntroductionIn view of environmental concerns and the shortage of good-quality coking coal, the COREX process was designed as a new ironmaking technology, attracting wide attention (Fang et al., 2005). In this process, lump coal and a small quantity of coke are directly charged into the melter-gasifier, where a high-quality reducing gas is generated for the reduction of the iron ore (Kumar et al., 2009). In contrast to the conventional blast furnace (BF) process, non-coking lump coal is used as the reducing agent and as the energy source, and the iron charge consists of lump ore and/or pellets, which results in the elimination of the coke oven and sintering plant as well as a decrease in investment (Kumar et al., 2009; Liu et al., 2012).Although the COREX process has made great progress, in current production practice the energy consumption greatly exceeds that of the BF, and it requires a certain amount of coke to maintain permeability of the semi-coke bed (Wang et al., 2008). In addition, the process consumes a lot of good-quality lump ore and lump coal. The pyrolysis of coal is the first step in most coal conversion processes, such as carbonization, gasification, and combustion (Aboyade et al., 2013). The reaction behaviour of lump coals in the COREX melter-gasifier is crucial, as it determines energy utilization and gas composition, as well as the metallurgical properties and particle size of the semi-coke produced (Prachethan et al., 2011; Zhang et al., 2014). In order to optimize the process and improve its competitiveness, the pyrolysis kinetics of Datong coal used in Baosteel’s COREX C-3000 facility was studied."

Jan 1, 2016

The utilization of computer assisted tomography (CT or CAT-scan)as general non-destructive examination (NDE) technique and as research tool for scientists in South Africa, is limited due to the relative unavailability or nonexistence of such specialized analytical equipment. Many medical hospitals are equipped with X-ray CT scanners for the diagnostic examination of patients but do not easily allow paleontologist or other scientist to utilize their very expensive equipment. As from 2003, Necsa hosts the South African Neutron Radiography (SANRAD) and tomography facility where neutrons from the SAFARI-1 nuclear research reactor and their penetrating power as well as X-rays as a complementing tool, are utilized in many R&D applications. This facility is being made available to HEI and specifically utilized by postgraduate students as part of their studies and/or by industry on an ad hoc commercial basis. The capability of these radiation imaging facilities at Necsa will be demonstrated in areas such as paleontology, geosciences and specifically the physical properties of rock and the distribution of minerals in borehole cores, petrophysics to predict the percentage tar/oil/water content within sandstone samples and others. The penetration capability of neutrons through specimens with a matrix of high atomic number (dense materials) and their ability to be attenuated by low atomic number material (light density) makes neutron imaging complementary to X-ray imaging. The capability of X-ray and gamma radiation for relatively easy penetration through specimens of low atomic number allows for viewing of imbedded high atomic number materials and density variation. X-ray micro focus radiography is capable of resolving objects of micro scale size that are micro distances apart whereas X-ray phase contrast radiography utilizes the wave properties of the electromagnetic spectrum of X-rays to clearly define edges of the specimen under investigation. Many applications with neutrons as imaging probe are successfully applied at several facilities across the globe such as at NIST in USA, Neutra at PSI in Switzerland, and ANTARES at FRM2 in Germany, etc, are documented 4?9, through world conferences on neutron radiography, for example. This is achieved through very well thought through and implemented instrumentation from the production of neutrons to their detection and interpretation of the images. The need arose at Necsa to upgrade the current facility from 42-year-old technology, which was successfully applied in neutron imaging over the past 10 years, to state-of-the-art technology found at European facilities. This initiative started under the auspices of an IAEA-TC programme for the period 2007?2010.

Jan 1, 2008

The first annual student prizegiving function of the South African Institute of Mining and Metallurgy was held in the Dorothy Susskind Auditorium, University of the Witwatersrand, on Thursday, 26th May, 1977. The address (see opposite page) was given by Dr M. G. Atmore, a director of Anglo American Corporation and Vice-President of the Institute.

Jan 1, 1977

By M. E. Rossi, C. Badenhorst

Conditional bias occurs when the expected value of the true grade conditional on the estimated grade is not equal to the estimated grade. It is a quantification of how the average of estimates differs from the true value. Conditional bias is present in all resource estimates due to the unavoidable properties of kriging, and indeed all linear estimation (regression) methods. In a mining resource estimation context, the degree of conditional bias is dependent on the spacing of the conditioning data; more data leads to the expectation of less conditional bias This paper discusses conditional bias from two perspectives: 1. 2. Estimates seeking to eliminate, as much as possible, conditional bias; and Estimates that accept a larger amount of conditional bias in resource models, in order to achieve a specific outcome. The problem of conditional bias in estimation can only be fully appreciated if the objective or purpose of a resource model is understood. There are instances where conditional bias should be avoided because it is not reasonable to make decisions using estimates that are known to be wrong in expected value; for example, when making a final decision in grade control with respect to the destination of the material. In most instances in the mining resource estimation context, however, the estimated values will not be “final estimates”, but “interim estimates”, meaning that in the future more data will be obtained, and the ”interim estimate” will then be updated. In this context, the most useful resource model is an interim model that is able to predict the final model estimates, despite not having all the data available that will be collected in the future. This is the objective, for example, of a recoverable “long-term” model developed prior to operating a mine, for example at the feasibility stage. It attempts to predict the ore that a processing plant will receive, well into the future. In such cases, it can be unequivocally demonstrated that conditional bias is not only unavoidable, it is a necessity.

Sep 1, 2021

By M. Mathey

The application of the Monte Carlo technique to production planning and everyday economic decisionmaking in mine production management is demonstrated. The logic is detailed using an example of underground production with continuous miners (CMs) and truck haulage. It is argued that availability of equipment and personnel are the predominant variables influencing mine output and productivity and that those availabilities may be well represented by binomial probability distributions. The probabilistic model is implemented in a standard Excel® spreadsheet with Palisade’s @Risk add-on to facilitate simulations. Starting from model calibration against data obtained from a mine’s annual reports, some general interdependencies of availability, utilization, productivity, and costs of production processes are outlined. Finally, several possible options and their consequences as regards production improvements are explored.

Dec 13, 2022

By C. V. O?Keefe

Volumetric flow and mass flow are two of the critical process parameters needed to understand and control flotation processes, with others being levels, densities, and metal analyses. Both volumetric flow and density measurements can be adversely influenced by entrained air, which will result in artificially high flow readings and artificially low mass flow calculations. Array-based instrumentation has been used successfully to accurately measure both volumetric flow of aerated slurry and the quantity of air entrained within the slurry. The latter measurement has been used to correct density measurements, thus providing an accurate mass flow calculation. A case study involving the use of this technology to measure both flow rates and air entrainment levels at Eland Platinum processing facility (concentrator) will be covered in detail. In addition, with certain traditional flow meters such as electromagnetic meters, erroneous volumetric flow rates can be recorded in the presence of paramagnetic or ferromagnetic material. The use of this array technology to avoid spikes in measurements due to steel fragments passing through the pipe will also be discussed.

Jan 1, 2012

By C. Debek, A. Wasilewicz, T. Czysz

"Both Polish and European hard coal mining nowadays faces the need of deepening shafts (significantly in some cases) or extending mining hoists, due to the exploitation of deeper coal deposits.In order to protect the crew working within a shaft, rope safety platforms (artificial shaft bottoms) are employed. Old solutions, based on rigid steel constructions with the external damping layers made of e.g. slag and up to several tens of metres long, are intended to absorb the energy of approximately 5 t mass falling a distance of 700 m. However, current requirements often assume a drop of 20 t to a depth of 1000 m or even more.More modern safety platform structures, made of one or more support rings with steel ropes stretched on them (rope platforms), are more compact (up to 3 m high) and lighter than traditional solutions. Multi-ring rope platforms with additional damping layers filling the empty spaces between the ropes are able to absorb sufficient energy to meet the current requirements.Single- and double-ring platforms have been employed in Poland to absorb the energy of approximately 5 t dropping to a depth of 900 m. They have been developed (and some have already been implemented) by SADEX Ltd. and are protected by various patents and patent applications.This paper presents a design for a triple-ring platform structure with six rope nets. FEM analysis was used to model the performance of the platform. According to the simulation, a 20 t mass falling from 1000 m (>100 m/s) will destroy all the nets, breaking most of the ropes and deforming the support steel boards placed on the nets, but will ultimately be stopped by the platform, as its kinetic energy falls to zero."

Jan 1, 2017

By J. S. Contreras, E. Córdova, I. Gottreux, A. Anani, A. Ferrada

Cave mining is an underground mass mining technique. The largest projects, which are known as ‘super caves’, produce hundreds of thousands of tons of ore per day, which involves large footprints with considerable column height, and have a life of mine of over 20-40 years. These operations are typically located deep, under high stresses and in competent rock masses, making initiation and propagation of the caving process harder to manage. These challenges must be confronted by optimizing the fragmentation of the orebody to achieve smaller size blocks that will result in consistent caving and improved flow of the ore from the drawpoints. To achieve better performance from the drawpoints, preconditioning is applied to fragment and damage the material required to cave. We present a proposed design for preconditioning in underground mines, considering the challenges that these large-scale mines are already facing, based on a comprehensive analysis of current design parameters, case studies, and sensitivity analyses using numerical models.

Feb 2, 2021

By J. Petersen, T. Moyo, D. Maharaj

This study investigates the effect of ammonium thiosulfate on the leaching of gold from the contacts of unpopulated cut electronic printed circuit boards (PCBs). Studies in the literature show ammonium thiosulfate to be a viable option in comparison to the commonly used but hazardous cyanide leaching route. However, the simultaneous dissolution of Cu interferes with the Au leaching reaction, often limiting the extraction to moderate levels. To optimize the system, an ammoniumthiosulfate system containing 0.5M ammonia, 0.5M ammonium thiosulfate, and Cu(II) sulfate at varying concentrations was studied as an alternative hydrometallurgical option for the recovery of gold from PCB. Tests were done with unpopulated standardized model PCBs (cut to 15 x 30mm pieces). Gold extraction of 47.3% was achieved after a 24-hour leaching experiment with a 0.02M copper background concentration. Further experiments focused using different initial background Cu concentrations (0M – 0.1M) to determine its effect on both gold and copper extractions. An initial Cu concentration of 0.045M resulted in the highest gold extraction, with 93.7% extraction after 6 hours of leaching. Further analysis of the data shows that the kinetic rate of gold leaching is correlated in a first-order dependence with the actual copper concentration in the solution, which increases with the concomitant dissolution of copper and gold from the PCBs. A lower threshold of 0.017M and an upper threshold of 0.15M copper in solution were determined, in between which gold extraction shows this first-order rate increase. The upper threshold is potentially linked to the onset of copper precipitation, which blinds the metal surfaces, slowing further leaching. The findings of this study suggest that in an industrial recovery operation of gold from waste PCB using the thiosulfate method, copper concentrations need to be carefully monitored, and the process should preferably operate with uncut or coarsely cut untreated boards to minimize exposure to copper circuits.

Dec 11, 2024

By W. Newcomen, G. Dick

"Effective management and mitigation of pit slope instability in open pit mines begins with a comprehensive slope monitoring programme. The ability to differentiate between non-critical pit wall movements due to rebound or relaxation of the excavated slopes and movements that may be indicative of slope failure is important for maintaining a safe working environment and maximizing production. Slope failure prediction methods using velocity, acceleration, and strain criteria have been introduced and put into practice over the past few decades. Forty-eight slope failures with surface monitoring data are presented and assessed using the strain-based failure prediction approach, with consideration of the quality of the rock mass and the potential failure mechanism. The results indicate that the strain-based approach can be used to provide general guidance regarding strain thresholds for pit walls for a variety of failure modes in diverse geological environments. The advantages and potential drawbacks of the strain-based and other slope failure prediction methods are discussed. The importance of implementing a pit slope monitoring and performance evaluation system early in mine development is also emphasized. IntroductionThe successful prediction of the Manefay Slide pit slope failure at Bingham Canyon at 9:30 am on 10 April 2013 (Engineering and Mining Journal, 2014) highlighted the importance of having a comprehensive slope monitoring system that provides an accurate prediction of the time of failure of an open pit slope. Using most of the geotechnical monitoring tools available, the time of the failure was predicted within hours and equipment and personnel were evacuated from the pit well in advance of the failure. From a time to slope failure perspective, the monitoring system in place was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities. was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities."

Jan 1, 2016

By N. D. L. Burger, S. Thorley

In engineering design of operators? compartments, in underground mining equipment, ergonomics principles are often neglected or not given the full recognition they deserve. This paper defines ergonomics, applies it to machinery in an underground mining environment, and describes the ergonomics analysis undertaken during the design phase of an EJC extra low-profile mining loader. Encompassing the design of the operator?s compartment of this new loader, this paper illustrates the importance of ergonomic principles within the collective design process ensuring that it is fully integrated into the design approach. An ultimate aim of this study is to ensure that all future designs follow this route to guarantee not only the outcome of a highly efficient, cost effective and productive machine but that it is also takes the human factor into account, not only in maintenance but also in operation. Maximizing comfort will have the ultimate outcome of actually increasing productivity beyond expectations.

Jan 1, 2004

By W. E. Stumpf

"SynopsisSouth Africa recently announced a resurgence in its commercial nuclear power programme. The implications for the development of the necessary high-level manpower within South Africa’s tertiary educational system and its national research and development (R&D) capacity in materials science and engineering, as well as in other engineering disciplines, are placed into perspective. An organized national process of developing this manpower by moving away from the previously high-risk and costly ’large programmes’ to rather a selection of ‘small and better’ research projects and a redefinition of what constitutes ‘nuclear materials’ are proposed as parts of this strategy.IntroductionSince 2008, and more particularly in 2014/2015, South Africa has woken up to the fact that significant steps need to be taken to ensure sufficient electricity generating capacity for the future, even beyond the coal-fired stations at Medupi and Kusile currently under construction. It is, therefore, encouraging to see some active large-scale wind farms in the Eastern Cape near Jeffrey’s Bay, in the Couga area, and others in the Western Cape already in operation. In addition, many solar energy projects are also progressing from the small localized scale to larger programmes in the Northern Cape, which may contribute some capacity on a national basis. South Africa needs to tap into its renewable resources of wind and solar much more, but will these projects solve the country’s long-term industrial needs? Unfortunately not. One cannot run mines and trains on solar cells. Industry needs reliable baseload capacity, and with very limited easily accessible hydrocapacity this leaves really only coal, possibly natural gas, and nuclear power as options. South Africa’s current over-reliance of about 90% on coal–fired power, however, places it in an internationally vulnerable position, and diversification into a more equitable energy mix should be a national priority for the medium to long term. South Africa cannot significant climate change confronting the human race, as the IPCC cautioned in 2013, and will have to adjust its future energy reliance to a more balanced combination of sources."

Jan 1, 2015

By D. E. Sweeney

In May of 1980, a mine operated by Belmoral Mines Ltd experienced a failed crown pillar, resulting in the death of eight miners and putting sixteen others in harm?s way. The Ferderber mine was located in the Val d?Or region of the province of Quebec in Canada, and had been under development for 19 months and production for 9 months, since the opening of the portal. The crown pillar separating the 1?7 level from overlying overburden ultimately failed, permitting an estimated 1.5 million cubic feet of liquefied sediment to gain entry into the mine. This paper back-analyses the cave-in by applying decision error theory, in an examination of the organizational culture and the collective decisions contributing to the cave-in disaster. A case will be made for a greater understanding of mining methodology, geomechanics and risk assessment when operating in such challenging geologic conditions. Boundary condition and decision (BCD) analysis will be introduced as an innovative new method for the analysis of mine accidents and incidents. It will also be shown that BCD analysis can be applied to any event in an enterprise for which standards, norms or legislation exists. A cognitive profile will be presented that provides insight into the safety ethos existing within the Ferderber mine organization at the time of the tragedy.

Jan 1, 2007

By J. C. Vreugdenburg, B. A. Dippenaar, J. Muller, T. L. de Vries

Iron ore fines are agglomerated in the sintering process to produce sinter: an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such as production rate and fuel consumption rate. The model uses the finite difference method (FDM) to solve heat and mass distributions within the sinter pot over the sinter bed height and time dimensions. This method can further be used for establishing empirical relationships with measured sinter properties. Inputs into the model include the feed material physical properties, chemical compositions, and boundary conditions that vary over time. Sub-models describe relationships between applied pressure differential and gas flow rate through the bed of granulated fine ore particles, combustion of carbonaceous material, calcination of fluxes, evaporation and condensation of water, and melting and solidification. Four sinter pot tests were performed and the model predictions validated against temperatures measured at depths of 100, 230, and 420 mm. Differences between predicted and measured temperatures indicated the need for optimization of some model parameters that are uncertain. Optimization resulted in an improvement in the correlation between the predicted and measured temperatures for all tests, although an acceptable level of agreement was not achieved in all cases. Using these parameter values, reasonable agreement was found in terms of typical performance parameters for three out of the four tests.

Jan 1, 2014

By L. Xingwana

"The purpose of this study is to understand how ore loss and dilution affect the mine call factor, with the aim of subsequently improving the quality of ore mined and fed to the mill. It was necessary to know the relationship between ore mined and delivered for processing in order for the mine to operate efficiently. A review of the literature suggested the mine-to-mill integration approach as a standard intervention to address declining mine call factors. A case study was undertaken at a gold mine in the Free State on the influence of the fragment size distribution on ‘free gold’, the effect of ore loss and dilution on the mill efficiency, and time tracking of ore movement from source to the plant. The study revealed that fragmentation, underground accumulation of ore, and dilution have a significant influence on the mine call factor and mine output. It was difficult to quantify the total ore loss due to the time lag between mining and milling, which is extremely variable, when estimating the mine process inventory. However, it was possible to estimate the total dilution with some degree of precision by analysing the daily blast and head grades. It is therefore recommended that mines accept that some gold loss and dilution will always occur during blasting and transport of broken ore, and this loss must be minimized.IntroductionThe mining of high gold grades is obviously very beneficial for the economic viability of an operation, but optimum recovery of the product is required to maximize profits (Chapman and Bindoff, 2010, p. 13). Although integrating these two requirements is very difficult, due to the various activities occurring between mining and processing, it is indispensable. The main driver of this integration is the impact that different ore types and characteristics have on head grade. According to Isokangas et al. (2012, p. 871), mining and processing operations involve a series of well-defined sequential stages that are complementary in an efficiently operating mine, with the performance of one operation affecting that of another. An attempt to optimize each function separately without considering the whole extraction process will not result in the optimum efficiency of the entire mine. Several researchers have developed a proven methodology for revealing these inefficiencies (Dance et al., 2006, p. 1)."

Jan 1, 2016