Search Documents

By G. W. Jones, I. Spolan

"INTRODUCTION The operation of internal-combustion engines at high altitudes and the general aspects of combustion processes in rarefied atmospheres have created considerable interest in the problem of ignition and flame propagation at low pressures. Nuckolls, Matson, and Dufour 4/ have published results on the effect of low pressures on the propagation of flame in gasoline vapor-air mixtures in vessels of large capacity. The volumes of their test equipment varied in capacity from 0.425 to 125 cubic feet. Various sources of ignition were employed. These authors found that the explosive range of gasoline vapor in air decreases with decreasing pressure at pressures considerably below atmospheric, until a limiting absolute pressure of about 33 mm. mercury at ordinary temperature is reached, at which point no appreciable flame is propagated.Experiments carried out at the Bureau with natural gas-air mixtures at reduced pressures have shown 5/ that the limits of inflammability are but little affected at reduced pressures down to 175 mm. mercury. As the pressures of natural gas-air mixtures are reduced below atmospheric, the mixtures become more difficult to ignite; however, if a suitable source of ignition is employed, the limits of inflammability are as wide at 175 mm. mercury absolute pressure as they are at atmospheric pressure. In view of these observations with natural gas-air mixtures, it appears important to investigate gasoline vapor-air mixtures for possible similar behavior. For this reason the tests herein described were carried-out."

Oct 1, 1946

By C. C. Merrill

Studies were made to determine the amenability of yttrium to fused-salt electrorefining in a controlled atmosphere. Tests were conducted in a LiCl- YCl3 electrolyte system at 710° C. The major variables studied were the YCl3 content of the electrolyte, from l.7 to 13.4 mol percent, and the initial cathode current density, from 410 to 1,630 amperes per square foot. Vacuum distillation was employed to remove salt from the deposited metal. Metallic impurities, except for lithium, could be reduced to near or below their lower analytical limits, ranging from 10 ppm for Cu to 300 ppm for Ta; reduction of oxygen content, however, was accomplished only in metal produced from electrolytes with 5.4 mol percent YCl3 or less. Initial cathode current density had little effect on the purity of the product.

Jan 1, 1967

By L. C. IlsLey

The work of the electrical section of the Bureau of Mines may be considered to have had its beginning in April , 1909 , when H. H. Clark was , appointed electrical engineer in the U. S. Geological Survey. The first manuscript prepared by members of this section was Miners Circular 5, which was issued in October , 1911. During each succeeding year additional papers have been published dealing with questions relating to electrical safety. Since 1916 the electrical section has also conducted laboratory investigations on flame safety lamps and gas- detecting devices and has published reports relating thereto . The following selected list of publications covering safety studies and activities of the electrical section has been prepared for the convenience of those who wish to keep themselves advised concerning electrical safety matters . The list includes only such publications as are applicable to present-day prac tices .

Jul 1, 1930

By R. O. Dannenberg

This Bureau of Mines report describes the results of research to develop a process for recovering additional beryllium from a commercial mill waste product, fluoferrate leach residue. Forty-five percent of the total beryllium in the leach residue was recovered in a beryllia product assaying over 98 pct Be0 by a process comprising (1) leaching with 1 N sulfuric acid, (2) adjusting the acidity of the leach liquor to pH 2, (3) extracting the beryllium with di-2-ethylhexyl phosphoric acid (EHPA), (4) stripping the loaded extract with sodium hydroxide solution, (5) boiling the sodium beryllate strip solution to precipitate beryllium hydroxide, and (6) calcining the beryllium hydroxide. Calculated reagent requirements per pound of Be° recovered by a proposed flowsheet were 28.1 lb sulfuric acid, 0.04 lb flocculent, 0.15 lb EHPA, 0.06 lb isodecanol (IDA), 0.22 gal kerosine, and 6.3 lb sodium hydroxide.

Jan 1, 1966

By P. F. Sands, Michael Sokaski, M. R. Geer

The purpose of this investigation was to determine the advantage of using either a conventional sieve bend ahead of a vibrating screen or of attaching a sieve - bend screen surface onto a vibrating screen to serve as a scalping deck when dewatering or draining dense medium from fine coal . In dewatering , use of either the sieve bend or scalping deck increased the capacity of the vibrating screen tenfold and the recovery of coal finer than 0.5 mm threefold , with no sacrifice in the moisture content of the oversize product . In dense -medium drainage , either the sieve bend or the scalping deck reduced the amount of magnetite retained on the product of the vibrating screen , particularly when the medium was as dense as that characteristic of the underflows from dense - medium cyclones . The sieve bend was slightly superior to the scalping deck in dewatering , but the scalping deck was clearly superior in dense -medium drainage . Additional advantages of the scalping deck are lower cost and a substantial saving in headroom.

Jan 1, 1963

By Charles C. Myers, Robert M. Doerr

The apparatus described was developed for determining the kinetics of gas - solid reactions at high temperatures by measuring the volume of gas consumed with respect to time . This apparatus consists essentially of a horizontal precision- bore glass tube connecting a small reaction chamber in a furnace to a large constant - temperature reservoir . A drop of mercury in the tube separates the two sides of the system and serves as an indicator that moves at a speed proportional to the rate of gas consumption . The sensitivity of the apparatus depends inversely on both the density of the gas in the system and the cross - sectional area of the tube ; with a tube having an area of 0.079 cm² , the sensitivity for oxygen at 308 ° K and 0.5 atm is 20 cm/mg . The reproducibility of data with the volumetric apparatus is good .

Jan 1, 1964

By Philip C. Good

Unweathered low-grade calcareous phosphate rock of about 20 percent P205 grade was beneficiated by a procedure in which contained carbonates were decomposed by calcination at about 1,000° C. On quenching the hot calcined rock in water, major impurities passed into a slime phase which was mechanically separated from a coarser concentrate fraction. Phosphate rock of two major types was beneficiated in batch-scale studies yielding concentrates containing 31.3 to 38.5 percent P205 at recoveries ranging from 54.8 to 86.0 percent. The samples were from two major deposits in India. Processing information gained was utilized in extending the work to a continuous-flow system, processing phosphate rock at rates up to 157 kilograms per hour. Superphosphate exceeding 16 percent water-soluble P205 was prepared from concentrate derived from continuous-flow processing.

Jan 1, 1976

By By Staff

"These proceedings consist of papers presented at a Bureau of Mines Technology Transfer Seminar on postdisaster survival and rescue research. Several seminars are held each year to bring the latest results of Bureau research to the attention of the mining industry as quickly as possible.INTRODUCTIONThe postdisaster research program is directed toward research and development of technology and equipment that increases the chances of a miner surviving or being rescued after an underground mine disaster. A disaster is an accident of major proportions, and it may result in the entrapment of miners whose normal egress from the mine is cut off. This often necessitates a rescue operation and a means of keeping the trapped miners alive while they await rescue. The Bureau is currently pursuing research to develop the technology that will enhance the ability of miners to survive such an occurrence. The research is divided into two basic problem areas, survival and rescue. Both areas are concerned with the inability of miners and rescue teams to cope with the postaisaster environment, such as toxic gases, unstable roof conditions, water flooding, and lack of oxygen. In addition, research is also conducted to find ways of locating and quickly reaching trapped miners. Most of the research conducted by the Bureau has been directed toward the postdisaster problems associated with coal mines. However, most of the research results are also applicable to noncoal mines as well.The papers presented in these proceedings address some of the recent research conducted by the Bureau of Mines that has been directed toward the postdisaster problems outlined above. The topics covered range from an overview of the technology developed for oxygen selfrescuers to training programs for mine rescue. Any questions or comments pertaining to this research are encouraged and appreciated. Open file report (OFR) references in the proceedings listed as available from NTIS may be obtained from the National Technical Information Service, Springfield, Va. 22161, and are also available for reference at Bureau of Mines facilities in Denver, Colo., Twin Cities, Minn., l3ruceton and Pittsburgh, Pa., and Spokane, Wash.; the Department of Energy facility in Morgantown, W. Va.; the National Mine Health and Safety Academy, Beckley, W. Va., and the National Library of Natural Resources, U.S. Department of the Interior, Washington, D.C."

Jan 1, 1982

By E. J. Gleim

This report describes a trip to Europe in the interest of safety in coal mines. It reviews the Eighth International Conference of Directors of Safety in Mines Re-search, which met in Dortmund-Derne, Germany, July 5-10, 1954, to discuss results of studies made in different countries to improve health and safety conditions under-ground. It also summarizes information on subjects of special interest in the United States gained by the writer in visits to mining experiment stations in Belgium, France, and England. The efforts being made to protect life and property underground were discussed, and ideas and experiences were interchanged freely, not only during the conference but also during visits to the several countries. Helpful information was obtained on many topics of interest, but time did not permit as thorough a discussion on some of them as might be desired.

Jan 1, 1956

By Philip G. Freeman

The growth-promoting properties of coal-derived humus were tested by a variety of bioassay methods. Humate materials used included leonardite, a form of naturally oxidized lignite, and humic acids extracted from leonardite. It was found that the greatest effects were evident when water-soluble humic acid was applied to excised root tips. No significant short-term effect was noted when water-soluble humic acid was applied to stem or coleoptile sections. Root initiation was promoted in bean stems when high concentrations of coal-derived humate were applied. Gross weight of tomato plants was increased by up to 40 percent when coal-derived humates were added in concentrations of 101 to 104 ppm to the nutrient in a hydroponic growth test of 6 weeks' duration. It is concluded that coal-derived humate promotes the uptake of minerals, specifically iron, by serving as a metal chelate.

Jan 1, 1968

By John Campbell, Miller. W. E., G. W. Jones

"INTRODUCTION Because of its interest in accident prevention, the Federal Bureau of Mines has cooperated with city officials and utilities in investigating the causes of explosions in sewers, manholes, and other underground spaces and has aided in the development of means to prevent such explosions. For several years this Bureau has cooperated with the Boston Edison Co. and the Boston Consolidated Gas Co. of Boston, Mass.,for the purpose of detecting and eliminating combustible and physiologically harmful gases in manholes in Boston and vicinity.These investigations 5/ have shown that combustible gases from the usual sources — leakage from gas—distributing systems and underground tanks and gasoline wastes — can be located and the dangerous conditions remedied by a well—planned, adequately supervised, systematic, and continuous manhole survey. However, other types of gas contamination, termed ""soil"" gases, are present in manholes at times and are more difficult to eliminate because they have no fixed origin and because seasonal and barometric chances affect their production and passage into the manhole. Soil gases usually are abnormally high in carbon dioxide and low in oxygen and contain varying amounts of methane. They are especially dangerous to men entering manholes because they lack sufficient oxygen to support life."

Feb 1, 1940

"The town of Monson in Piscutaquis County, Maine is the, center of an important site industry. Monson slate has a nation-wide reputation, particularly for electrical switch boards, and the deposits have been worked for the manufacture of such products for many years. Open-pit quarrying is the method most commonly employed in obtaining slate. Underground methods have been used in the Peaon Bottom district near Delta, Pennsylvania, but the quarries that were thus operated are now abandoned. Underground methods have been used more extensively in foreign countries, the most famous example being the slate mines at Angers in France, where an over-head stoping method has been employed successfully for many. It is only under special conditions that underground methods can be successfully used. If the deposit is wide and relatively thin, or if the material is too unsound to constitute a safe roof, open-pit methods must be used, for slate is too low-priced a commodity to justify the heavy expense of any timbering methods. It is only where the deposit is relatively narrow, of great depth, and sufficiently sound to afford a strong roof that ordinary mining may be employed.The best slate beds in two of the three quarries operated at Monson are no worked by underground methods. The chief bed worked by the PortlandMonson Slate Co. is 10 feet thick, stands vertical and strikes N. 63º F. The slaty cleavage is vertical and crosses the strike of the beds at an angle of 5 to 10°. The grain or second direction of splitting is vertical and perpendicular to the cleavage. In addition to the 10-foot bed, to 2-foot beds and one 5-foot bed are available but are not now utilized. In theMonson Maine Slate Co. quarry (the old Pond quarry) a greater number of beds available, but at present quarrying is confined to a single bed about 9 feet thick which dips 30º S.E. and strikes N. 47ºF. The slaty cleavage is vertical and strides N. 45º F., while the grain strikes N. 45-50º W. and is also vertical."

Nov 1, 1920

By Charles L. Kimbell

Available statistics on 1991 worldwide consumption of selected non fuel mineral commodities shown in table 12 indicate downturns for all but 3 of the 15 listed commodities. It should be stressed that in most instances, the consumption declines were primarily the result of lower levels of use in the former U.S.S.R. and the former centrally planned economy nations of Eastern Europe. However, several commodities suffered use cutbacks in market economy countries. In the case of the nonferrous metals covered In the table, the differences in performance between market economy countries and the former centrally planned economy states are immediately evident from the table itself. Among these important commodities, refined lead, primary magnesium, and refined tin registered downturns for market economy countries as well as among the centrally planned economy countries. Also notably, cadmium use showed no significant change from 1990 levels in either group of countries. Global consumption of iron ore fell by 3.4 % or about 31 million tons, and this was a greater decline than that logged for production of marketable iron ore and related products, which was down by only 3.0% or almost 28.2 million tons. Thus, it would seem that for another year there was a net addition to stocks. The 1991 drop in iron and steel scrap use was about 5.5 % or about 18 million tons, on the percentage basis somewhat greater than the 4.8% or 36.9 million ton drop in global steel production. Although consumption of iron ore and iron and steel scrap are not broken down by region in table 12, it seems almost assured that the pattern of 1990 continued into 1991: drops in use in the former U.S.S.R. and Eastern Europe were the overwhelmingly dominant declines and accounted for much, although not all, of the global decline, whereas among market economy countries as a group, there were upturns for both materials. On a global basis, it would appear that the slight shift in the ratio of pig iron to scrap in steel furnace charges noted in 1990 continued into 1991, this shift being toward a slightly larger proportion of pig iron with a corresponding decline in the share accounted for by scrap.

Jan 1, 1993

By G. Nuñez, M. A. Pathak, C. F. Stanley

"Holographic interferometry is a non-destructive technique to detect small deformations1 of an object. It is a whole-field technique· with an accuracy of a few microns. An adaptation of holographic interferometry is time-averaged holographic interferometry which is particularly useful in detecting small vibration amplitudes of an object under investigation. Its application to biological tissue is especially difficult due to the combination of (a) the high sensitivity of the technique, and (b) the tendency of these objects to deform excessively, or move during the testing period. (This is also compounded by the changing moisture content of the tissue surface.)Ideally, a pulsed laser and fast-acting thermoplastic film camera could be chosen to overcome these difficulties, but the total equipment cost could exceed $75,000. In this paper we describe our relatively economical method to apply time· averaged holographic interferometry to an excised animal lung, utilizing holographic plates and a mechanically-shuttered continuous-wave Argon laser.EXPERIMENTAL METHODThe schematic of the experimental setup is shown in Fig. 1. The holographic equipment, including the laser, is fixed on a 3 ft x 6 ft x 4 in. honeycomb holographic table. This table is functionally similar to one described by Mark and Horsch2 which can be constructed for about one thousand dollars. The holographic table itself rests on six inner tubes to absorb floor vibrations. All unnecessary vibrations must be reduced to preserve the quality of the holograms. A laser beam from a 0.5-watt continuous-wave Argon laser is split by a circular variable beamsplitter (Newport Corporation Model 50GOOAV.1) into two beams, i.e., an object beam and a reference beam. The object beam is again split into two beams of equal intensity by a 50150 beamsplitter (Newport ·Corporation Model BS.1). These beams are optically filtered and expanded by spatial filters (Newport Corporation Model 910) to cover as much area of the object as possible. Soft biological tissues exhibit low reflectives, resulting in a relatively high reference to object beam ratio of roughly 5 : 1 at the holographic plate."

Jan 1, 1989

By V. A. Marple, K. L. Rubow

"In our laboratory several impactors have been developed in the past which have penetration characteristics that approximate that of the ACGIH or the British MRC respirable curves. In these impactors the large nonrespirable particles are collected on an impaction plate of a multiple round nozzle stage where the nozzles are of different diameters. The principle for designing a respirable cut impactor is quite simple in that the respirable curve is divided into two or more segments and the nozzles are designed with the correct diameters and number of nozzles to have collection characteristics with 50% cutpoints at the center of each segment. The particles not collected on the impaction plates are then collected upon a filter. These particles represent the respirable fraction of the aerosol. Therefore the respirable curve is approximated in a stepwise fashion with the approximation becoming better as the respirable curve is divided up into increasing numbers of segments. It has generally been felt that three segments is satisfactory for most cases.A new version of the respirable impactor has recently been developed in our laboratory. This impactor approximates the ACGIH respirable curve in three steps at a flow rate of 30 liters per minute. However, unlike previous models where all of the particles larger than the three cut points designated by the three steps are collected upon one impaction plate, a separate impaction plate is now used for each of the three cut sizes. To approximate the respirable curve in three steps, the cut sizes must be 2.2, 3.5 and 5.8 microns diameter. Therefore, on each of these stages the particles collected will be the mass of particles that are larger than these three cut sizes. By determining the mass of particles collected on each of these three stages plus that on the after filter using Gravimetric techniques, some information can be obtained on the size distribution of the aerosol being sampled. Furthermore, the impaction plates of the three stages are rotated and the nozzles are placed in such a position such that a uniform deposit is obtained on each of the impaction plates. Therefore, the deposits collected are suitable for X-ray fluorescence analysis or other types of analysis where a uniform deposit is required."

Jan 1, 1988

By Arno C. Fieldner

Forty years have elapsed since the Bureau of Mines was established on July 1, 1910, by Act of Congress. The convocation of this Sixth International Conference of Safety in Mines Research Directors, 24 days after our 40th birthday, seems to be an appropriate time for reviewing our contributions to mine safety research and the problems yet to be solved from the American point of view. Actually research on safety in coal mines was started by the United States Government in the Technologic Branch of the U. S. Geological Survey of the Department of the Interior in 1908, as a result of a succession of disastrous coal mine explosions in which many lives were lost. In 1910 this work was transferred to the newly created Bureau of Mines. 394 lives were lost annually per 100,000 men employed in the coal mines of the United States in the 5-year period ended in 1910, as compared to 203 lives lost annually in the 5-year period ended with 1949. In 1908 no safe, permissible types of explosives and no certified permissible equipment of any kind were used in American coal mines. Black powder was in universal use and open oil or acetylene lights were common in all but mines known to be gassy. Rock dusting was not practiced to limit propagation of explosions, nor was ventilation in many mines adequate, Our safety practice lagged behind that of foreign coal- mining countries and therefore one of the first steps in carrying out the Congressional Authorization of 1908 to investigate the causes of mine explosions was to obtain assistance from the leaders of mine safety research in foreign countries. At the request of Dr. Joseph H. Holmes, director of the Technologic Branch of the Geological Survey, James R. Garfield, Secretary of the Interior, obtained the cooperation of the Governments of England, Belgium and Germany in sending Captain Arthur Desborough, Inspector of Explosives in England, Mr. Victor Watteyne, Inspector-General of Mines in Belgium, and Mr. Carl Meissner, Counselor for Mines in Germany, to visit American mines and make recommendations for increasing safety and efficiency in mining coal in the United States.

Jun 1, 1950

By Van H. Manning

EXPLOSIVES RESEARCH. As the physical laboratories of the explosives section of the Pitts- burgh experiment station were equipped for testing the physical properties of explosives, both the Army and Navy Departments for many years had requested the Bureau of Mines to make such tests. Chemical control of the physical tests through analyses, heat tests, analyses of gaseous products of combustion, and sand tests was exer- cised through the explosives chemical laboratory. Often an investigation was cooperative between two laboratories. The explosives chemical laboratory also aided the work of the Ex- plosives Regulation both by chemical tests and investigation of acci- dents in explosives plants. COOPERATIVE WORK FOR ARMY AND NAVY DEPARTMENTS. The explosives chemical laboratory devised, at the request of the Bureau of Ordnance of the Navy, a more economical method of making hexanitrodiphenylamine. This problem was assigned to the Bureau of Mines by Dr. C. E. Munroe, chairman of the committee on explosives of the National Research Council, acting as the depart- ment of science and research of the Council of National Defense. Before the United States entered the war the following reports of investigations were submitted to the Army or the Navy: 1. Report of sensitiveness and relative efficiency of TNT and ammonium picrate, dated February 6, 1913, undertaken at the re- quest of the Chief of Ordnance. 2. Report of tests and examination of two samples of TNT and one of TNA for the Ordnance Department of the Army, dated August 5, 1915, was undertaken at the request of commanding officer, Frankford Arsenal. 3. Report of tests for sensitiveness to detonation of mercury ful- minate of 21 samples of TNT crystallized from various solvents, for the Bureau of Ordnance, Navy Department, dated June 17, 1916. 4. Report of tests of two samples of mercury fulminate for Frank- ford Arsenal, dated December 2, 1916, undertaken at the request of the commanding officer, Frankford Arsenal. After the United States entered the war the following reports of investigations were submitted: 5. Report of pendulum friction and large impact tests on two samples of "sodatol" and two samples of "amatol." The final report was dated July 20, 1918; and the preliminary report, May 15, 1918. This investigation was undertaken at the request of the Ordnance

Jan 1, 1919

By H. P. LeVan

The Bureau of Mines has developed a technically feasible continuous single-stage leaching and thickening system for extracting manganese from umber by a sulfuric acid-ferrous sulfate process; the cocurrent leaching and thickening system proved simpler to operate and control than the countercurrent leaching and thickening system developed earlier" Related tests investigated the use of a centrifuge to replace thickeners for separating the product liquor from are residues and compared several chemical agents for removing iron from the pregnant manganese leach solutions. Results of Some exploratory autoclaving tests are also given.

Jan 1, 1972

By G. E. Walden

The Bureau of Mines is currently engaged in a continuing investigation of the thermodynamic properties of certain inorganic compounds. As a part of this investigation, the heat contents of bismuth and cerous chlorides were measured throughout the temperature ranges of 370° to 630° K. and 370° to 1,200° K., respectively. Equations representing heat contents as a function of temperature were derived from the data by the method of least squares. These equations were used to calculate heat contents at selected temperature intervals ranging from the ice point to 650° K. for bismuth chloride and to 1,200° K. for cerous chloride; also, the heats of fusion of both compounds were calculated at their respective melting points. EXPERIMENTAL Materials The cerous chloride used in this investigation was supplied by the National Carbon Company of Cleveland, Ohio. A chemical analysis indicated Ce 56.57 percent and Cl 43.39 percent. No attempt was made to purify the compound or identify impurities since the analysis showed only about 0.04 percent total impurities. Reagent grade bismuth chloride was used without additional purification.

Jan 1, 1961

By J. P. Hansen

The Bureau of Mines has investigated the S02 leaching of MgO from high-MgO-bearing Florida phosphate concentrates. The S02 was effective in leaching some of the MgO from three phosphate concentrates; flow rate of the S02 and leach time were major factors in determining the amount of MgO leached. Calcining the samples, then grinding to minus 200 mesh, and elevating the leach temperature gave only small increases in the amount of MgO leached. The research also showed that some of the MgO was so intimately associated with the phosphate mineral that it could not be removed by S02 leaching. This amounted to about 0.6, 0.7, and 1.0 pct MgO in three leached residues. The calculated heads for the three concentrate samples averaged 1.4, 1.1, and 1.5 pct MgO, respectively, before leaching.

Jan 1, 1985