Search Documents

By Raymond B. Ladoo

Garnets are usually found well crystallized in the cubic system , the principal forms being rhombic dodecahedrons , tetragonal trisoctahedrons or combinations of the two , and hexoctahedrons . They also occur as rounded disseminated glassy grains and in compact massive , laminated or gramlar aggregates . They vary greatly in color , but the most common garnets , almandite and andradite , are most often found of a dark red or reddish brown color .

Apr 1, 1922

By Steven G. Grannes

This U.S. Bureau of Mines report summarizes Federal mandatory belt conveyor automatic fire suppression system installation requirements and inspection procedures, identifies system failure modes observed during in-mine investigations, and suggests system design and maintenance upgrades which, if implemented, would result in an improvement in overall system reliability. This report is a compilation of recommendations based on discussions with Mine Safety and Health Administration (MSHA) inspectors, review of manufacturer's literature, discussions with mine personnel, and research investigations of automatic fire suppression system performance in the laboratory and in mines. The Code of Federal Regulations (CFR) requirements for installation, inspection, and maintenance of fire suppression systems should be regarded as minimum standards.

Jan 1, 1990

By Charles B. Kenahan

Vanadium is subject to only light corrosion in phosphoric acid at temperatures up to 60° C. and has a moderate corrosion rate in this acid at 100° C. It is relatively corrosion resistant in sulfuric and hydrochloric acids up to 60° C, but corrodes rapidly at 100° C. It corrodes rapidly in dilute nitric acid at 35° C. Vanadium is almost inert in 10-percent solutions of formic, acetic, lactic, tartaric, and citric acids; in 9-percent oxalic acid it corrodes slowly up to 60° C. and rapidly at 100° C. Vanadium is resistant to corrosion in substitute ocean water, tapwater, and in 3-percent sodium chloride and 10-percent sodium hydroxide solutions. It is readily attacked, however, by 20-percent ferric chloride, 20-percent cupric chloride and 5-percent mercuric chloride solutions. Vanadium is protected by contact with magnesium, aluminum, and steel SAE 4130 in substitute ocean water, by magnesium and aluminum in 3-percent sodium chloride solution, and by magnesium in tapwater. Vanadium protects copper in substitute ocean water. When vanadium and stainless steel are coupled in sulfuric acid solutions, both metals are usually unaffected by contact, whereas the corrosion rate of titanium in sulfuric acid is greatly reduced by contact with vanadium.

Jan 1, 1962

By M. J. Beus

Researchers at the U.S. Bureau of Mines have developed personal-computer-based data acquisition, instrumentation, and mine visualization and modeling techniques to evaluate a mine accessway in a deep hard-rock mine in northern Idaho. These techniques were applied to a mine shaft in a large silver mine that has been in operation for many years. A very deep, rectangular, timber-supported shaft extending to depths exceeding 2.3 km (7,500 ft) had been deforming continuously as a result of nearby mining, resulting in operational problems. Preliminary visual observations and rock and support monitoring confirmed that severe diagonal distortion was occurring. Extensive field measurements and data analysis confirmed initial observations, provided insights into the cause of deformation, and defined a general approach to structural modeling. Computer analysis of the problem was initiated by developing a three-dimensional model of the terrain. This represented a volume of rock approximately 80 km3 (40 x 1010 ft3) and an area on the surface surrounding the mine 9 km2 (3 square miles). Based on this model, a three-dimensional, finite- element analysis was conducted to establish boundary conditions for sequentially more detailed two- and three-dimensional submodels of the shaft area. Results from the computer study are being used to develop new approaches to mine design and to provide design guidelines for deep mine accessways subject to severe rock-mass loading conditions.

Jan 1, 2010

By M. Carrales, C. J. Jirik, W. D. Dietzman

In view of the developments and recent interest in recovering heavy oil , this report was prepared to present general information on more than 2,000 heavy oil reservoirs in more than 1,500 fields in 26 states . Information given on each heavy - oil deposit includes the following items : Field and formation , location , average or range of depth , average API gravity of oil , average thickness of formation , areal extent of field , total productive wells drilled in field , discovery date of field , field status in 1963 , cumulative production to Jan. 1 , 1964 , and all known types of secondary - recovery operations initiated ( active and terminated ) in the reservoirs . The geographical location of heavy oil accumulations in the United States is shown by a map , and a brief discussion of 14 different areas is given in the text . As of Jan. 1 , 1964 , 75 percent of the heavy oil reservoirs in the United States had produced more than 10 billion barrels of oil and are estimated to contain over 90 billion barrels of oil in place . It is also estimated that if the deposits which have had little or no production history , such as the one in Missouri , were included , the total remaining heavy oil in place would be in excess of 150 billion barrels . To find economical ways of recovering this vast reserve of heavy oil , industry is developing technology in several types of thermal - recovery methods . Some of the general considerations and more suitable limitations in selecting a prospect to study for thermal - recovery techniques are : Lithology , depth , viscosity of reservoir fluids , gravity of oil , reservoir thickness , oil in place , and permeability and porosity .

Jan 1, 1965

By J. R. Thoenen

The objective of this circular is threefold: First, to describe briefly the various modes of occurrence of sand and gravel. Second, to emphasize the need for adequate prospect¬ ing and exploration prior to the expenditure of funds for development and plant construction. Third, to describe various methods of prospecting and exploration and their application to the several modes of occurrence of sand and gravel. Sand and gravel may be found in nearly every county or township in the United States. Commercial deposits, however, are by no means so widespread. The introduction of concrete and the consequent impetus given to consumption of gravel and sand aggregates has seriously depleted deposits in some congested areas. Increasing re¬ strictions in the specification requirements for marketing sands and gravels have further narrowed the economic areas. On the other hand, the combination of increasing transportation costs and decreasing selling prices has forced the decentralization of gravel production. As a result smaller, intermittently operated, and widely scattered portable or semiportable unit plants have been encroaching on the territory formerly supplied from centrally located pits with large tr.atment plants. Generally speaking, the small portable plant can not produce any great variety of ma¬ terials to as exacting specifications nor as economically as the large permanent plant.

Dec 1, 1932

By G. R. Peterson

To determine the availability of aluminum from world bauxite resources, the Bureau of Mines investigated 139 bauxite deposits worldwide and evaluated the potential production of aluminum based on the demonstrated resources of bauxite ore from 91 mines and deposits in 22 market economy countries. The demonstrated resources of the bauxite mines and deposits included in this study represent an in situ resource of 20.2 billion metric tons of bauxite. Total identified bauxite resources in market economy countries amount to roughly 31.9 billion tons. Of the demonstrated resource, some 18.8 billion tons of bauxite considered minable provide a production potential of 3.6 billion tons of primary aluminum. Given the wide geographic distribution of bauxite deposits, stable supplies of bauxite for aluminum production seem assured well into the next century. However, a tight market situation could develop during the 1990's unless the real price of aluminum increases enough to stimulate massive new investments in production capacity, particularly in refining and smelting. This study indicates that a real price of at least $0.85 per pound (in January 1980 dollars) would be necessary to stimulate the required investments and provide a sufficient rate of return on invested capital.

Jan 1, 1983

By E. D. Eastman

There are three researches upon the specific heat of water vapor by the method of explosion that are sufficiently advanced in technique and suitable in plan to justify careful study of their results , with the double purpose of fixing the best available experimental values and indicating the attainable accuracy of the method. These three researches comprise the work of Pier , Bjerrum , and Siegel.5 The work of earlier date than Pier's suffers from obvious inaccuracy of measurement , while the experiments more recent than Siegel's , such as those of Womersley6 , of Bone and his collaborators , and of Maxwell and Wheeler , 8 are for the most part not well designed for the accurate determination of the heat capacities in question . Some of the errors to which they are especially subject have been discussed by David and by David and Thorp.

Sep 1, 1930

By C. Harry Benedict

This paper, describing the leaching practice at the Calumet and Hecla mills, Lake Linden, Mich., is one of a series on milling methods and costs being published by the United States Bureau of Mines. GENERAL DESCRIPTION The reclamation plant is located along the shores of Torch Lake at a slightly lower level than the concentrator itself. The entire location of the original concentrator, in connection with the present reclamation plant, has been ideal, lore particularly as the leaching and flotation departments are common to both units. After 15 years of operation and with the reclamation sands just a little more than half exhausted it would appear that the remaining life of the deposit could be worked by the present plan, without decided changes or renewals of plant or equipment.

Jan 1, 1930

By Jeanne A. Zimmer, Brad Smith, Steve Viles, Andrew B. Cecala

A recent report evaluating silica exposure levels in the metal/nonmetal mining industry noted that bag packaging and loading are some of the occupations at the greatest risk. In addition to dust problems, the bag-stacking process is labor intensive, making lost-time injuries common due to back fatigue and strains. During the bag-stacking process, a significant amount of dust can be generated, mainly from product on the outside of the bags and from dust escaping the bag valve upon impact of the bag on the pallet. In an effort to address dust-exposure and back-fatigue issues, Malvern Minerals Co., Hot Springs, Ark., made two major improvements to its ground silica stacking facility. First, the company purchased a semi-automated bag palletizing system (Figure 1). With this system, the bag stacker does not lift the bags, but slides them across a metal table. Small jets of air exit through perforations in the table top (similar to an air hockey game), allowing workers to more easily slide each bag into the proper position. After each layer of bags is completed, the table slides open, and the entire layer of bags is loaded onto an underlying pallet. The table then closes, readying it for another layer of bags. After the entire pallet is loaded, the unit delivers the pallet to a shrink wrap and forklift pick-up area. In addition to this semi-automated palletizing unit, Malvern Minerals purchased an Overhead Air Supply Island System (OASIS) to lower the bag stacker's dust exposure. The OASIS takes outside air, directs it through MEASURING RESPIRABLE DUST The bag stacker's respirable dust exposure was monitored using a RAM-1 instantaneous dust monitor to evaluate the impact of the various changes on the palletizing process and dust-control equipment. The bag stacker wore a vest that held the 10-mm Dorr-Oliver cyclone, which classifies the respirable portion of dust. Flexible tygon tubing was used to connect the cyclone to the RAM-1 dust unit, allowing the bag stacker to perform the palletizing process with minimal interference. The RAM-1 measures respirable dust concentrations by light scattering with a sensing chamber. This device closely simulates gravimetric measurements when calibrated for a specific dust. This instrument is ideal for comparative evaluations, as was the case in this study. Since the RAM-1 is not an MSHA-approved instru¬ment for dust compliance sampling, the dust concen¬trations listed in this article should be used as a com¬parative value of respirable dust concentration and not to determine actual dust concentrations from a com¬pliance standpoint.

By D. E. Wolfson

This report presents 900° C BM-AGA carbonization and related data for coals from the principal beds of Nicholas, Randolph, and Webster Counties, W. Va. Thirty-three samples from nine coal beds in three counties were car-bonized at 900° C in the l8-inch-diameter BM-AGA retort, data from which have been correlated with industrial production. Host of the samples were chemically suitable for metallurgical use, and their coking properties were satisfactory. Except for four of the Lower Kit-tanning samples, the ranges of constituents in the coal seams were 1.8 to 9.0 percent ash and 0.4 to 1.1 percent sulfur, values within the range of accept-ability for metallurgical coals. Coke strength indexes were normal for Appalachian coals of similar rank, and the tumbler stability indexes of the coke ranged from 35 to 57.

Jan 1, 1969

By A. A. Cochran

Bureau of MinesThe Bureau of Mines studied the development of practical methods for recovering manganese from the extensive domestic resources of low-grade ores and open hearth slags. A one-step operation was developed on a laboratory scale in which manganese and iron compounds are treated with chlorine, volatilized, and separated by selective condensation. Manganese recoveries of 90 to nearly 100 percent were obtained from 9 of the most important domestic ores. Analyses of the manganese chloride product indicated that it was suit-able for aqueous electrolysis with little additional purification. A complete, integrated process that provides for the recovery and recycling of chlorine is proposed. This process appears to have distinct advantages over previously proposed manganese recovery processes, and, in sharp contrast to leaching procedures, it is applicable to practically any manganese-bearing material.

Jan 1, 1967

By N. H. Darton

In mining coal in the anthracite region of Pennsylvania the general custom has been to leave a large percentage of the coal in place as pillars to support the roof. Evidently any practice that involves partial waste of an important mineral resource is bound to be discarded. It is well recognized that one method of obviating probable waste is to fill the workings with cheap or worthless materials, a process extensively employed in the anthracite and some European mines. At present many of the collieries in the anthracite region of Pennsylvania are utilizing refuse from the old culm banks, which formerly were prominent features in the landscape, and are flushing the fine waste underground so that pillars may be reduced in size or removed. As a result the banks are now disappearing and soon will be gone. The fine culm from the breakers and rock from the mines will continue to be available, but the volume of these materials is insufficient to replace any considerable proportion of the coal removed. The next stage of progress suggested is the use of sand. Fortunately there are available large deposits of this material, much of which can be handled by dredges and pumps. This report is issued by the Bureau of Mines in the interest of safer and more efficient mining methods. I ts purpose is to describe the sand deposits in the northern anthracite coal field in Luzerne and Lackawanna Counties, Pa, Much of the information available is presented in the map, Plate I. Field studies, mostly preliminary, were made in the summer of 1911 to determine the distribution, amount, and character of the larger deposits. It was not thought desirable to make a detailed examination of the region because when the coal companies decide to utilize the sand their engineers will make precise surveys and drill test holes. In preparing the map the various coal companies were consulted; they contributed a large number of facts, especially as to the deposits in the buried valley of the Susquehanna between Pittston and Nan- ticoke, where nearly 1,000 test holes have been bored. The results of these borings were placed at the author's disposal, and have been utilized in drawing the boundaries given in the wide valley area and its extensions up Lackawanna River and NewportCreek. Wyoming Valley contains deposits of sand that are 100 feet thick over a wide area, 200 feet thick in places, and over 300 feet thick in the deep old channel south of Plymouth.

Jan 1, 1913

By E. R. Cole

This Bureau of Mines investigation was prompted by the need forr a stable anode for electrowinning metals, particularly zinc and copper, from acid solutions. The polarization behavior of Pb-Ag (1 pct Ag) anodes in H2SO4 and fluoride solutions was determined as the first step in the development of such an anode. A Luggin capillary, dc power supply, high-impedance voltmeter, and other equipment standard to an electrochemical laboratory were used in this study. It was determined that during polarization, a relatively hard, stable coating of Pb02 was formed on the surface of the lead-silver anode and the rate of formation of this coating was considerably enhanced by the presence of fluoride ions in solution. Subsequent investigations at the Bureau of Mines Rolla Research Center resulted in the development of a Pb02-coated titanium (Pb02-Ti) anode. Results of this effort were presented in Bureau of Mines Report of Investigations 8111. Additional data resulting from extensive testing of the Pb02-Ti anodes, as well as process improvements and innovations, are included in this report. The anodes were considered generally unsatisfactory for zinc electrowinning because of lower conductivity, higher oxygen overvoltages, and shorter in-cell life as compared with the Pb-Ag anodes now being used in industry. However, the PbO2-Ti anodes were used successfully to oxidize waste chromium solutions and to electrowin copper.

Jan 1, 1981

By A. Gene Collins

This report discusses some of the chemistry and geochemistry of cesium and rubidium. Knowledge of the cesium and rubidium content of oilfield waters aids in resolving the origin of waters and petroleum, exploring for petroleum and other valuable minerals, discovering water pollution sources, and augmenting the knowledge of geologic formations. The methods described in this report permit the detection of less than 0.01 mg/l of cesium and/or rubidium in a complex oilfield brine or water. Solvents possessing high-dielectric constants were evaluated for their ability to extract cesium and rubidium tetraphenylboron from oilfield waters and for their flame emission characteristics. Nitroethane was selected and used for the extraction and flame spectrophotometric determinations because it gave the highest sensitivity. Cesium 137 and rubidium 86 were used to determine the extraction efficiencies, which were about 87 percent and 58 percent respectively using a single 10 ml nitroethane extraction from a distilled water matrix. The standard deviation of the determination was 0.0008 mg for cesium and 0.0007 mg for rubidium in the 0.01 mg range.

Jan 1, 1965

By C. W. Davis

There are four parts to this circular and, respectively, they list firms in the Eastern (pp. 5-8), Southern (pp. 9-10), Central (pp. 11-15) and Western (pp. 16-22) United States and Provinces of Canada. Before listing the laboratories and the work performed there, it is proper to make clear what is done and what is not done by Federal bureaus, States, and Territories, as well as by Canada and Mexico. FEDERAL Bureau of Mines. - The Bureau of Mines does not make assays, analyses, or tests for individuals or firms unless they be incidental to investiga¬tions that are of possible benefit to the entire mineral industry. All significant results obtained in this way are made public through published reports. Any mineral sample sent to this Bureau for simple identification will be subjected to a cursory examination.

Jan 1, 1938

By W. L. Dare

This information circular is one of a series published by the Federal Bureau of Mines in which the methods and costs of producing uranium ore on the Colorado Plateau are discussed. This report describes the three largest company-operated uranium mines of Climax Uranium Co. - the G-1, the Mineral Joe, and the Frank No. 1. Climax Uranium Co., a subsidiary of American Metal Climax, Inc., was [corporated] May 11, 1950, just 2 years after establishment of the domestic uranium program by the Atomic Energy Commission. Twenty-five years earlier Arthur H. Bunker, now chairman of the board, American Metal Climax, Inc., organized and operated the U. S. Vanadium Co. at Rifle, Colo.3/ Soon after Climax Uranium Co. was organized, it entered into a contract with the Federal Government to build a uranium-vanadium processing mill in Grand Junction, Colo. Under the contract Climax leased from the Federal Government certain uranium-bearing lands that had been withdrawn from public entry in 1948. From Minerals, Engineering Co. on June 12, 1950, Climax acquired other uranium-vanadium properties on Calamity, Outlaw, and Monogram Mesas in Colorado and on Polar Mesa and in the Yellow Cat area of Utah. To house the milling equipment, Climax leased the old Grand Junction sugarmill building of the Holly Sugar Co. Milling facilities, based on a then new process developed for treating both uranium and vanadium, were completed, and the plant went into production in 1951.

Jan 1, 1959

By Jerry A. Wichser

A series of linear programmed instruction modules was developed in the general subject areas of Blasting Technology & Explosives Safety & Electrical Training. The linear programs (modules) were developed in the form of tape-slide plus workbook materials, while the branching format evolved from the LTS teaching machine system from MIT, through several other teaching machines and micro-computers, finally settling on Radio Shack TRS-80 microcomputers, Models I & III. Initial validation figures indicate that essentially the same result, are attained from both methods (based on pre and post test scores), with the most noticeable difference being an approximately 25% savings in study time with the branching modules. In December 1980, the development of modules on High-Voltage Training, Trolley Wireman Training, and Compressed Gas Safety was added to the overall tasks of the contract.

Jan 1, 1984

Ground-water and tailings pond monitoring in the Upper Santa Cruz Basin Mines Task Force's Special Studies Area has been performed to determine the nature and extent of aquifer contamination from copper tailings pond's recharge in the basin. A monitoring program for each of three mining areas (Mines A, B, and D) was developed. Analysis of data shows that recharge from Mine A's ponds has caused increased hardness, sulfate and total dissolved solids in local ground water. However, pumpage in the area has controlled most of the water's movement. Pond recharge from Mine B has led to similar conditions, and the degraded water is moving towards a local public-supply well. Pumpage from Mine D's interceptor wells is controlling some, but not all, of the movement of recharge seepage from Mine D's ponds. Recommendations include the need for enhanced monitoring programs at each current mine site, development of a monitoring program for Mine C's area, development of water budgets for all mines, investigation of tailings pond compaction and sliming, establishment of mine closure plans for containment of recharged pond water, and the need for additional interceptor wells in several locations.

Jan 1, 1983

By Frank G. Horino

The Bureau of Mines studied the uniaxial compressive strength of model rock pillars as a function of the angle and spacing of noncohesive planes of weakness. The model pillars were prepared from NX 2-l/8-inch diameter drill core of limestone, sandstone, and granite, and the planes of weakness were diamond saw cuts ground flat and smooth. The angle of the planes of weakness, measured from the horizontal, varied from zero to 57° in approximately 15° increments. When two planes of weakness were used, the thickness-to-diameter ratio of the wafer was 1/4, 1/2, and 1, Approximately 400 model pillars were tested in uniaxial compression. The results indicate that the uniaxial compressive strength of model pillars decreases rapidly as the angle of the plane of weakness increases from 30° to 57°, and that the spacing of these planes of weakness has only a minor effect on the strength. The effect of the number of horizontal planes of weakness, with a spacing of 1/4 and 1/2 of the diameter, upon the compressive strength of model pillars was also investigated. These results indicate that as the number of planes of weakness increases the compressive strength of the pillar decreases. Normalizing the data provides useful estimates of model pillar strengths for any rock type.

Jan 1, 1968