Search Documents

By Susan E. Brink

The first step in determining whether Mn can be recovered by in situ leaching is to develop and test a selective lixiviant. Two column leach tests and one core leach test Were conducted by the U.S. Bureau of Mines on Mn oxide ore using aqueous sulfur dioxide (SO2) as the lixiviant. The column tests showed that aqueous S02 could selectively dissolve available Mn oxides from calcite-rich ore in a heap leach system. However, the core test showed that calcite gangue side reactions can have pronounced negative effects on the likelihood of successful in situ leaching of a calcite-rich ore with aqueous S02. Petrographic and geochemical analyses showed that both Mn (IV, III) oxides and calcite were dissolved. The abundance of dissolved Ca caused precipitation of gypsum. Acid consumption by calcite dissolution caused a rise in pH that caused the SO/S species to shift to S032-(sulfIte), which hindered reductive dissolution of Mn oxide. Gypsum precipitation did not affect complete leaching of the rock fragments in the column tests; however, it plugged the natural permeability in the core. Manganese recoveries were high for the column tests and low for the core test.

Jan 1, 2010

By Robert F. Chaiken

A novel approach to eliminating environmental and public safety hazards that are associated with fires in abandoned coal mines and waste banks involves the use of in situ combustion technology developed by the Federal Bureau of Mines to accelerate the burning of the wasted coals in place. This technology would be used under exhaust ventilation control conditions that would allow for total management of the hot gases produced. Combustion stoichiometries would be optimized to minimize unburnt combustibles and to maximize the heat content of the gas products, which will be exhausted at one or more fan locations. When necessary, scrubber systems would be employed to remove air pollutants, such as sulfur dioxide; heat utilization systems (process heat, steam, and electricity) would also be employed to offset operational costs. Ultimately, complete burnout would solve the fire and acid water formation problems of the abandoned coal mine or waste bank. Pertinent technical data for burnout control are derived and discussed in terms of the important material and operational parameters. In general, it is believed feasible to operate a burnout system in an existing abandoned mine or waste bank fire at thermal power levels in the range of 10 to 100 Mw, and at exhaust gas temperatures of 1,000° C (1,830° F).

Jan 1, 1980

By Charles A. Seitz

This Bureau of Mines report describes a chromatographic method for analyzing impurities in helium that utilizes a helium carrier gas contain-ing 25 to 30 ppm Ne. An example of the effect of trace amounts of nitrogen, methane, and moisture on the detector's response is shown. The added neon in the carrier does away with irregularities of the analysis which were experienced when the carrier contained up to 3 ppm Ne. The addition of 25 to 30 ppm Ne causes a loss of sensitivity, but the re-maining sensitivity is adequate for routine analyses. The high-neon carrier allows positive and more linear responses for eight impurities: neon, hydrogen, argon, oxygen, nitrogen, methane, carbon dioxide, and ethane. Neon concentration levels of 0.02 to 125 ppm in helium carrier gases were studied. The high-neon carrier has been in successful rou-tine use in Bureau of Mines helium facilities since October 1981.

Jan 1, 1985

By H. G. Iverson

Solid state reactions of manganese with silica were investigated in high-temperature tests. Reactions of 0.5 to 4.0 moles manganese (Mn) with 1 mole silica (SiO2) at 1,100° C and of 2.0 Mn:SiO2 mole-ratio mixtures at 1,000° to 1,150° C yielded products consisting of a slag phase and a metallic phase. At 1,100° C, the slag phase from reactions of the low Mn:SiO2 mole-ratio mixtures was composed of SiO2 and rhodonite (MnSiO3), and the slag phase from the high Mn:SiO2 mixtures was composed of MnSiOs and tephroite (Mn2SiO4). The metallic phase from the corresponding low Mn:SiO2 mole-ratio reactants consisted of two manganese silicides, Mn5Si3 and Mn3Si; from the high Mn:SiOg mixtures, it was Mn and the manganese silicide (Mn5Si). For the higher mole ratios of MnSiO2 the manganese content in the metallic phase increased, while the manganese and silica contents of the slag phase remained nearly constant. The slags did not contain free or uncombined manganese oxide (MuO). For the 2.5 to 4.0 Mn:SiO2 mole-ratio mixtures reacted at 1,100° C, the maximum quantities of silica reduced and of the manganese in the slag appeared to become asymptotical at about 41 and 48 percent, respectively. A brominating procedure was developed that was highly selective in removing the metallic constituents from the reaction product, leaving the slag phase as residue. X-ray diffraction patterns were obtained on prepared silicides Mn5Si, Mn3Si, and MnSi.

Jan 1, 1967

By F. S. Wartman

The presence of magnetite, either dissolved or suspended as solid crystals, in slags from the copper reverberatory furnace is a frequently mentioned cause of an abnormally high copper content in those slags. The presence of this oxide in the slag is to be expected, since it is present in appreciable amounts in both converter slag and roaster calcine which comprise a considerable proportion of the furnace feed. Magnetite is also a product of some of the furnace reactions. These abnormal losses result in several ways. Magnetite is supposed to favor the formation and retention of copper ferrite, in the slag. Crystals of solid magnetite suspended in the slag are objectionable-because they make the slag less fluid and often entrap globules of matte. Frequently these crystals settle into a layer at the slab-matte interface which may have such mechanical strength as to create a false bottom and interfere with furnace operation by preventing separation of matte from slag. Magnetite may, by crystallizing on the furnace bottom, build the bottom to such a level that the furnace can no longer be operated.

Jan 1, 1928

By K. P. Wang

The foundation of Japan's growing industrial and economic strength lies primarily in minerals, power, and technical know-how. Domestic raw material resources cannot supply domestic demand, and imports are indispensable. The Japanese are forced to acquire minerals and metals on a global basis, and their activities already have made an impact on international markets. A by-product of these efforts is the development and expansion of mines in many parts of the world to supply Japanese requirements. Japan now has a surplus capacity to produce finished products for consumption and export. Tradition-ally, domestic deficits in minerals have been met by importing crude materials. Because of the rising demand, however, the time has come when semi finished products as well as crude minerals are required. While the domestic market is the mainstay for Japan's industrial products, expanding export markets are essential for balancing trade and for providing economic prosperity and higher living standards for the Japanese people. Japan has a long history of mineral and industrial development, and the best in modern practices abroad has been adopted and modified for use under Japanese conditions of smaller enterprises, cheaper labor, and a more closely knit society. Generations of industrious workmen, technicians, and business-men have been trained in industrial occupations. Devastation of war temporarily slowed progress, but at the same time provided the opportunity for reconstruction, modernization, rationalization, and expansion. The Japanese excel in small and medium-sized operations, but they also have mastered large-scale production. Management is aggressive, practical, and strongly imbued with the concepts of effective utilization of resources. Integrated operations, diversification of facilities, intense competition among concerns in the domestic market, and close cooperation in foreign activities characterize Japanese industrial policies. Available capital has been utilized up to the limit for the establishment of mineral and other industrial facilities at home and abroad. Technology, machinery and equipment, and transport services have been exported along with venture capital, and funds have been advanced against future delivery of foreign raw materials. The Government has been restrained in regulatory functions and has provided technical services to private industry. Thus, Japan's technological foundations are secure, management practices are efficient, and government has stimulated production. The future outlook is bright for the continued rapid growth of mineral and other industries in Japan. Already supreme in Asia in per capita output and living standards, Japan steadily is gaining on the European countries. Steel production has overtaken the United Kingdom and is pressing the level in West Germany. Consumption of fuels and power is expanding at a rapid rate. Construction activities are booming. Japan has built up medium-sized non-ferrous industries. Its ability to produce the exotic metals needed in the nuclear space age is well established. Since Japan makes a great variety of mineral products, her overall posture in mineral extraction and processing is strong. Primarily as a result of intensive efforts in the mineral and other industrial fields, Japan is emerging in world markets as a serious competitor to all industrialized nations.

Jan 1, 1962

By F. E. Block

The metallic reduction of vanadium chlorides was investigated by the Federal Bureau of Mines as a possible new route for preparing vanadium metal in an effort to develop a production process that would be adaptable to large-scale plant production and would yield metal of uniformly high quality. Vanadium tetrachloride was usually prepared by chlorinating vanadium pentoxide in the presence of carbon. Although oxygen-?free tetrachloride was difficult to prepare this way, it could be prepared by the direct chlorination of vanadium carbide. Lower valent vanadium trichloride was prepared by the thermal decomposition of vanadium tetrachloride. Vanadium dichloride was also prepared by the thermal disproportionation of vanadium trichloride.

Jan 1, 1961

By G. S. Scott

[In the course of the investigation the Bureau of Mines is carrying on to determine the causes, behavior, and control of mine fires, the detection of incipient heating underground in the mines and above ground in refuse banks has received consideration. A report has been puplished5/ describing apparatus and tests made on anthracite to determining the amount and composition of the oxidation products when normal dry air was passed through it at temperatures varying from 100° to 350° C. These tests showed that the amount of evolved gases and their relative prorortions varied with the temperature. From: these results, graphs were prepared by which `he temperature at which the coal was oxidized could 'be estimated, thus giving a possible means of detecting incipient heating.]

Jan 1, 1938

By G. S. Scott

[In the course of the investigation the Bureau of Mines is carrying on to determine the causes, behavior, and control of mine fires, the detection of incipient heating underground in the mines and above ground in refuse banks has received consideration. A report has been published5/ describing apparatus and tests made on anthracite to determine the amount and composition of the a oxidation products when normal dry air was passed through it at temperatures varrying from 100° to 350° C. These tests showed that the amount of evolved gases and their relative proportions varied with the temperature. From these results, graphs were prepared by which the temperature at which the coal was oxidized could be estimated thus giving a possible means of detecting incipient heating.]

Jan 1, 1938

By W. P. Diamond, J. R. Levine

The explosion hazard of methane-air mixtures has become an increasingly serious mine planning problem, and an advance assessment of methane gas potential can therefore be essential for a safe and economic mine development pro- gram. As part of its coal mine health and safety program, the Bureau of Mines has developed a simple, inexpensive test to measure the methane content of coal samples obtained from exploration cores. The gas content of coal per unit weight as determined by the direct method test can be used as a basis for a preliminary estimate of mine ventilation requirements, and to determine if degasification of the coalbed in advance of mining should be considered. Since the Bureau began measuring the gas content of coal samples in 1972, experience has led to equipment and procedural changes, the most significant of which has been the development of a ball mill for crushing the coal sample to release the residual gas at the end of the desorption test period. This revised procedure replaces the crushing box and graphical methods described in earlier Bureau publications. The results of 583 direct method tests are summarized in tabular form. These results include data on the gas content of 125 coalbeds in 15 States.

Jan 1, 1980

By J. F. Neill, O&apos

[The Cartersville mining district is in Bartow County, Ga., about 40 miles northwest of Atlanta. Barite, limonite, ocher, amber, hematite, and, manganese oxide ores have been produced from the strict since about 1840. In the search for a possible source of manganese ore, Bureau of Mines engineers made a preliminary study of the district from September 1950 to January 1951. During this study 139 deposits were examined, and many mineral exposures were sampled. Manganese mineralization occurs as fine oxide and concretionary pellets in residual clays, as fine oxides in umberous clay, in brown-iron deposits, and in a limited quantity in mud ponds and Jig-tailing piles. The future supply of ferrograde manganese ore from the district, using current mining and benefication methods, appears limited to the recovery of the hard manganese ores deposits. Rough estimates indicate a reserve of manganese-bearing clays of about 8,000,000 long tons. This type of deposit has been extensively exploited and the larger deposits mined out to depths of from 50 to 200 feet. The remainder of these deposits are low grade, are covered with deep layers of colluvium, or lie below the ground-water table. Any future production from this source will require systematic prospecting, improved concentration, and an increase in the price of concentrate.]

Jan 1, 1954

By Ludwig Schmidt

Large quantities of gasoline are lost each year by evaporation from bulk-storage station tanks. The rate of evaporation from bulk-station tanks is influenced by two principal factors: First, the vapor pressure of the gasoline in the tank; and second, the amount of "breathing" of the tank. The vapor pressures of the gasoline govern the amount of the gasoline vapor in the air-vapor mixture above the gasoline in a tank at a given temperature. This is one of the principal factors in determining the total pressure of the air-vapor mixture within the tank. The "breathing" of the tank is caused by the inflow of air from the atmosphere during certain periods of the day and the expulsion of the air-vapor mixtures at other times, caused by atmospheric variations. The pressure built up within a tank and the amount of gasoline in the air-vapor mixture are both a direct function of the temperature existing within the tank. Therefore, two of the most common methods for reducing evaporation losses from bulk-station tanks are: (1) The use of vapor-tight tanks equipped with relief valves and operated at 1 or 2 ounces of pressure and about 1/2-ounce vacuum; (2) reducing the temperature of tanks and their contents by painting them a light color, by insulation, and in some instances by using water sprays. Water sprays, although effective, usually are too expensive to operate economically. In order to determine and compare the effects of various colors, insulation, and pressure in reducing the evaporation losses of gasoline held in storage in bulk-storage tanks, the Bureau of Mines made observations from May 29 to October 15. 1930, on five horizontal tanks of 12,000-gallon capacity each, which were erected at the plant of Black. Sivalls and Bryson Manufacturing Co., Kansas City, Mo. This report gives in detail the results of these evaporation tests.

Jan 1, 1931

By Richard F. Link

The principal procedures for the statistical analysis of gold assay and other trace-element data depend on applying either the normal frequency distribution or the lognormal frequency distribution. The consequences of applying both methods are examined through reference to example data from United States and South African gold mines. It is concluded that for estimation of average grades, except for certain data with a very high coefficient of variation (ratio of standard deviation to mean), use of the lognormal distribution is ordinarily undesirable because bias may be introduced and little efficiency can be gained. However, if biased average grades can be tolerated, as in the examination of data from surveys in exploration geochemistry, use of the log-normal distribution may be desirable. Various statistical analyses are detailed, and the tables presented to implement the analyses are more complete than those previously published.

Jan 1, 1971

By S. L. Weber, V. Castranova, D. E. Banks, J. K. H. Ma, Y. Rojanasakul, J. Y. C. Ma, M. Bhat

"The mechanism of bleomycin-induced pulmonary fibrosis is not ye: clear. Recent studies have shown that alveolar macrophages (AM) can be stimulated by bleomycin in vitro releasing inflammatory cytokines, suggesting that the interaction of bleomycin with AM is an important step in the drug-induced fibrotic process. Bleomycin is known to bind DNA and generate oxygen radicals through complexation with Fe2+ and oxygen. To provide,more insight into the cellular oxidative property of bleomycin, v.s have developed a fluoromicroscopic method using 2',7'-dichlorofluorescin diacetate (DCFHDA) as an oxidative fluorescence probe to study the deomycin-induced intracellular oxidation in rat AM and the inhibition of the oxida¬tion by taurine, a compound known to inhibit the bleomycin-induced fibrosis. Bleomycin at 5 to 20 ug/ml has a moderate stimulatory effect (1.87- to 2.66-fold) on the secretion of superoxide anion. A high concentration of bleomycin (20 ug/ml), however, inhibits cell response to zymosan-induced secretion of superoxide anion. At 4 ug/ml, bleomycin has no effect on cell membrane integrity or morphology but results in a significant increase in intracellular oxidation. This oxidative process is Fe2-,-dependent and is accompanied by an increase in intracellular calcium (35 nM). Both the intracellular oxidation and calcium rise induced by internalized bleomycin are inhibited by pretreatment of cells with varying concentrations of taurine (25, 125, and 187.5 uM). The inhibitory effect on intracellular oxidation .vas found to be 36, 57, and 60%, respectively. These results demonstrate a stimulation-inhibition relationship between bleomycin and taurine on re cellular oxidation at a subcytotoxic dose of bleomycin, suggesting that the oxidative effect of the intracellular bleomycin-Fe2 complex is important in the initiation of the fibrotic process. — Environ Health Perspect 102 (Suppl10):91-96 (1994) IntroductionThe pulmonary system is most susceptible to oxygen radical-induced diseases due to its constant exposure to the highest oxygen tension, and the potential encounters with oxidant gases such as ozone, nitrogen oxides, and toxic doses of dust particles. The lung is also a well-perfused organ and thereby vulnerable to the effect of circulating xenobiotics such as paraquat, and, bleomycin, which is known to cause pulmonary injuries (1). Alveolar macrophages (AM), which act as a means of defense by phagocytizing inhaled dust particles and microorganisms while increasing production of reactive oxidative species, have been shown to play an important role in mechanisms leading to oxidative lung injury and fibrosis (2-4)."

Dec 1, 1995

By Frank E. Federspiel

In 1986 and 1987, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 47,000-acre Electric Peak study area (part of the formerly-designated RARE II Non-wilderness Recommended Area no. 1609) to evaluate its' identified mineral resources. The study area is in Powell and Jefferson Counties, YT, about 30 mi southwest of Helena and 30 mi north of Butte. Three lode localities within the study area contain an estimated 159,000 tons of identified subeconomic resources containing gold, silver, and accessory lead, copper, and zinc. Resources at those localities range from 10,000 to 134,000 tons with grades ranging from 0.04 to 0.32 oz/ton gold, 0.92 to 16.42 oz/ton silver, 0.14 to 79.65 percent lead, and as much as 0.41 percent copper and 0.68 percent zinc. One property also contains 0.15 percent antimony. Gold, silver, and base-metal content in samples of poorly exposed mineralized structures indicate that further exploration may identify resources on seven additional study area localities.

Jan 1, 1988

By Anthony Iannacchione

One of the more pressing engineering problems for deep longwall mines in the Southern Appalachian Basin is to design longwall systems that will eliminate catastrophic coal pillar failure from the working environment. The purpose of this study is to quantify the behavior of a particular size abutment pillar prone to burst or bump. Because the 24.4-111 (80-ft) square abutment study pillar is within the pillar size commonly used in this region, understanding the behavior of this pillar should aid in future efforts to design optimum mining strategies. This research has attempted to construct the pillar stress and roof-to-floor convergence profiles in order to evaluate the ultimate strength, deformation modulus, visco-elastic deformation, and violent failure characteristics of the pillar during longwall mining. This information reflects the overriding influence of the local geologic characteristics on bursts, provides the field measurements needed to verify concurrent modeling studies, and suggest some basic mechanisms associated with the coal pillar bursts discussed in this paper.

In the U.S. coal mining industry, a large cohort of miners is at or nearing retirement age. As these miners retire, there will be a need to hire and train thousands of new and most likely younger workers. Moreover, a large portion of safety trainers will also require replacement due to retirement. In a speech before the U.S. House of Representatives (2004), Bruce Watzman, Vice President for Safety, Health and Human Resources for the National Mining Association said, “[W]e will need to replace a major portion, approximately 50%, of the underground coal mining workforce within the next 5–7 years.” The large influx of new mine workers, along with the deficit in safety trainers, creates the challenge to provide consistent and effective safety training. Given the expected high turnover of the mining workforce, it is very likely that incoming workers will have much less experience than those leaving the workforce. Unfortunately, inexperienced miners have been shown to incur the highest rate of injuries. The piece of machinery most associated with these injuries is the roof bolting machine, which accounts for 56% of machinery-related injuries in underground coal mining. The National Institute for Occupational Safety and Health (NIOSH) has released a new report entitled “Roof Bolting Machine Operators Skills Training for a Walk-Thru Roof Bolter: Trainer’s Guide” (IC 9489). It is designed to help safety trainers develop struc-tured training for new operators of walk-thru bolting machines. This resource will help trainees learn, understand, and apply knowledge and skills. Included in the trainer’s guide are the following tools: [ ] a six-part DVD video series, a skills check survey, talking points, and a complete job training analysis. Also included is an exercise to help trainees learn more about their mine’s roof control plan, as well as a list of supplemental training and reading materials. On-site trainers can modify this guide to fit their particular mine conditions, machines and equipment, and work procedures. The goal of every coal mine safety professional is to increase safety awareness and make mines a safer place to work. The Walk-Thru Bolting Machine Trainer’s Guide will help teach new miners skills to create a safer working environment that will ultimately prevent or reduce on-the-job injuries. Safety trainers can also use the ideas and concepts from this guide to develop their own training skills for the safe operation of other pieces of underground coal mining equipment.

Jan 6, 2007

By M. Howard Berliner

In August 1943 the Bureau of Mines completed seven churn-drill holes in an area of old mine workings near Linden, Wis., formerly known as the Argall mine. The work was undertaken as part of a general investigation by the Bureau of the zinc and lead producing area of southwestern Wisconsin at a time when special effort was being made to increase the production of metals necessary for war. The area was selected for investigation on the basis of its favorable geologic structure, past history, and apparent mineralization.

Jan 1, 1948

By H. H. Schrenk

One phase of Bureau of Mines work in health and safety is promotion of the use of safe, satisfactory, and reliable respiratory protective devices. To insure that such devices will be. available, the Bureau has established schedules of minimum requirements for oxygen breathing apparatus,3/ gas masks,/ supplied-air respirators (hose masks, air-line, respirators, and abrasive blasting helmets, hoods, or masks),5/ and dispersoid (dust, fume, and mist)

Jan 1, 1943

By C. F. Ellis

Interest in the composition of automobile exhaust gases has been greatly accelerated by recent studies that have indicated that these gases contribute to smog formation in urban areas. Several analytical methods have been published for the analysis of the hydrocarbons in the exhaust gases, but similar information has not been published on the analysis of the oxygenated compounds. This report presents procedures for chemical analyses of certain oxygenated compounds, procedures for sampling the exhaust gases for these analyses, and the analytical results of some experimental work in which these procedures were used. A stationary 1956 model, 170 horsepower, V-8, dynamometer-mounted engine, operated to simulate vehicular cruise conditions, was used for the study. Exhaust gases produced from a regular-grade Midcontinent gasoline during 15-40- , and 60-mile-per-hour cruise operations were analyzed by chemical methods for formaldehyde, total aldehydes, total carbonyls, total alcohols, carbon associated with the oxygenated compounds, and the oxides of nitrogen. Experimental results indicate: 1. The range of concentrations of the total of the functional groups of oxygenated compounds, expressed as moles per million moles of water-free exhaust gases, is about 90-100; the concentrations increase with engine speed. 2. Aldehydes comprise about 80-90 mole- percent of the total of the oxygenated groups, and formaldehyde accounts for about 50 mole-percent of the total aldehydes. 3. The order of magnitude of the concentration of the carbonyls is the same as that for the aldehydes, indicating that ketones are not a major group. A colorimetric test indicates that methyl ketones Constitute about 2 mole-percent of the oxygenated compounds.

Jan 1, 1961