Search Documents

By D. J. Parker

On Thursday, March 18, 1937, the country was shocked by news of a terrific explosion at the New London, Tex., school, which caused the death of 280 pupils rind 14 teachers. The explosion occurred at about 3:05 p.m. in the largest of the 11 school buildings on the campus. Figure 1 shows this building, market; "Main high school building?, with respect to other buildings, pipe lines, oil wells, and gas lines on the property.

Jan 1, 1937

By Peter Swanson, Collin Stewart, Wendell Koontz

A seismic monitoring network has recently been installed in the North Fork Valley coal mining region of western Colorado as part of a NIOSH mine safety technology transfer project with two longwall coal mine operators. Data recorded with this network will be used to characterize mining related and natural seismic activity in the vicinity of the mines and examine potential hazards due to ground shaking near critical structures such as impoundment dams, reservoirs, and steep slopes. Ten triaxial strong-motion accelerometers have been installed on the surface to form the core of a network that covers approximately 250 square kilometers (100 sq. miles) of rugged canyon-mesa terrain. Spread-spectrum radio networks are used to telemeter continuous streams of seismic waveform data to a central location where they are converted to IP data streams and ported to the Internet for processing, archiving, and analysis.

By R. H. Grau

Researchers from the National Institute for Occupational Safety and Health have demonstrated that mine-wide ventilation in large-opening stone mines can be improved by using low-pressure, high-volume propeller fans and constructing stoppings in key locations to direct and control airflow. In light of these findings, a comparative study was conducted to determine if a portable diesel-powered propeller fan could per-form more efficiently for dust dilution and transport than an axial vane fan for localized ventilation. The objective of this study is to evaluate both fan types for ventilation efficiency at an underground dump/crusher facility in a limestone mine. Results showed an improvement with the propeller fan to dilute both the respirable dust and the respirable silica dust around the dump/crusher facility. Overall, an average reduction of 20% in respirable dust and silica was observed at the dump/crusher location with the propeller fan.

By Marvin E. Lane

This paper , which describes the mining methods and practices at the Hayden Creek lead mine of St. Joseph Lead Co. in southeast Missouri , is one of a series being prepared by the Bureau of Mines on mining methods , practices , and costs in various mining districts of the United States . The Hayden Creek mine is in the W 1/2 sec . 7 , T. 36 N. , R. 4 E. , St. Francois County , Mo. , about 1 mile southwest of the town of Frankclay ( fig . 1) . The mine is on the west edge of the mining district known as the Lead Belt . However , neither the ore body nor the underground workings are connected with those of any other mine in the district . In contrast with most operations in the district , underground haulage is entirely trackless , and nearly complete delineation of the large , well -defined ore body by drilling permitted comprehensive planning of development and mining in advance of shaft sinking . The ore differs in character and occurrence from that of the main ore deposits in the Lead Belt in that the lead mineral , galena , occurs in the dolomitic matrix enclosing granite boulders instead of in dolomite limestone .

Apr 1, 1957

By J. J. Burns

Disasters such as occurred at Oppau, Germany, in 1921, at Tessenderloo, Belgium, in 1942, and in this country at Texas City, Tex., in 1947 clearly indicate the explosive hazard associated with the manufacture, storage, and transport at ion of ammonium nit rate The importance and extent of the hazard may be Judged from the large amount of ammonium nitrate produced and transported annually in this country. Between July 1, 1947, and June 30, 1948, it was estimated that the United States produced 461,528 tons of ammonium nitrate commercially for agricultural purposes alone .5/ In addition, U. S. Army Ordnance plants have manufactured and shipped 779,730 tons of ammonium nitrate fertilizer to Germany, Japan, and Korea.6/

Jan 1, 1953

By William H. Schiffbauer

One of the safety and health research programs of the former U.S. Bureau of Mines Pittsburgh Research Center was the evaluation of technology that will provide remote-controlled operation of mechanized equipment in underground room-and-pillar mining. The purpose of this effort was to enable workers to be located away from the hazardous and unhealthful coal extraction area (the face). As part of this program, advanced machine navigation and control technologies were developed for underground room-and-pillar and highwall coal mining that can be applied to commercially available mining equipment. These technologies use off-the-shelf components and a flexible control software architecture to minimize the effort required to adapt them to mining equipment. An accurate, reliable navigation system that can provide the mining machine's heading and location is a critical requirement for a remote-controlled mining system. After investigating several different types of navigation sensors, researchers selected the Honeywell Ring Laser Gyro Inertial Navigation System (INS) as showing the most promise. It was installed on a continuous mining machine at our Mining Equipment Test Facility. Extensive testing at an open pit (OP) site was also performed. This report describes the INS as it was employed on the mining machine in the laboratory, in the field, and OP tests, and provides the accuracy and performance results of the OP and highwalltests.

Jan 11, 1997

By Lewis A. Martin

Researchers from the Spokane Research Laboratory, National Institute for Occupational Safety and Health, in cooperation with engineers from the Department of Mining and Geological Engineering, Montana Tech, Butte, MT, conducted tests to evaluate the tensile strength, fiber count, and adhesion of shotcrete applied to panels at the Chief Joseph Mine, a research and training facility operated by Montana Tech. The tests were conducted in the mine ramp 45 m (150 ft) inward from the access portal at a 15.25-m- (50-ft) long test area divided into five 3-m- (10-ft) long sections. The shotcrete was applied with an Aliva 240.5 machine fitted with a predampener. Different amounts of fiber were entrained for each panel. Background data for the tests were obtained from earlier tests in Nevada, where the typical amount of fiber in the shotcrete is 6.54 kg/m3 (11 lb/yd3). All shotcrete was applied to a minimum thickness of 76 mm (3 in). Cylindrical cores were drilled at the wall-rock interface, and adhesion was tested after 28 days of curing. The goal of this research is to reduce the need to install multiple supports at the advancing face by creating a safer mining system that limits the time miners are exposed to unprotected roof.

Jan 1, 2004

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

By Carl Sunderman, Steve Signer

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed several new tools for evaluating roof support performance. A miniature data acquisition system (MIDAS) was developed that can collect readings from up to 16 strain gauges at regular time intervals and store the readings for later retrieval. Three LED lights change from green to yellow, then red, based on the reading levels and/or rates of change of rock movement. This feature can be used to warn miners of rock instabilities. The system can be used with any strain-gauged support (resin bolt, friction bolt, cable bolt) or with a newly developed rock strain strip (ROSS) developed by NIOSH to measure rock strain. A ROSS is grouted in a hole drilled adjacent to the rock support to be evaluated; the deformed shape of the ROSS provides anchorage on either side of the strain gauges. Data from both laboratory tests and field evaluations are presented that describe the capabilities of both the MIDAS and ROSS instruments.

Mining activity during 1977 was limited to the production of limestone, marl, and sand and gravel, all of which were used domestically. Public works projects consumed the major portion of the construction material produced. The consortium of oil companies operating as Esso Ventures Inc., drilled one exploratory well off the coast of southern Belize. For drilling the well, Exxon Corp. received a 57% working interest in the consortium's concession located 40 kilometers east of Puta Gorda. No other offshore drilling was attempted in 1977. Esso also drilled a well on the Anschutz Overseas Inc. concession in the Toledo District of south- eastern Belize. The attempt wee abandoned, but seismic activities continued.

Jan 1, 1981

By R. L. Merek

There were 63 fatalities in the California petroleum industry in 1929, the largest number in any year since 1923 and an increase of 34.0 per cent over 1928, when 47 men lost their lives in the drilling, producing, manufacturing, and marketing divisions of the industry. It will be observed from the accompanying chart that after following a consistent decline for 4 years, the fatality curve turned upward in 1923 and advanced sharply in 1929. Although this increase in fatalities coincided with a period of intensive development it tends to indicate some laxness in the industry during a period of increased hazards. Intensive drilling campaigns are usually started hurriedly and conducted with a great demand for speed, and the result is that accident-prevention work is too often relegated to a position of minor importance.

Jan 1, 1930

By R. L. Marek

There were 63 fatalities in the California petroleum industry in 1929, the largest number in any year since 1923 and an increase of 34.0 per cent over 1928, when 47 men lost their lives in the drilling, producing, manufacturing, and marketing divisions of the industry. It will be observed from the accompanying chart that after following a consistent decline for 4 years, the fatality curve turned upward in 1923 and advanced sharply in 1929. Although this increase in fatalitics coincided with a period of intensive development it tends to indicate some laxness in the industry during a period of increased hazards. Intensive drilling campaigns are usually started hurriedly and conducted with a great demand for speed, and the result is that accident-prevention work is too often relegated to a position of minor importance. [ ]

Jan 1, 1930

By E. C. Westman

Three-dimensional velocity tomograms were generated on a daily basis to image mining-induced changes to the overburden above a longwall mine. The hypothesis was that a coherent redistribution of seismic velocity, due to the development of high-stress zones, could be imaged at the mine scale. Seam depth was 360 m and source location depth varied from 100 to 1000 m. Sixteen geophones were distributed over a 600 by 600 m square area on the surface above the mine. More than 12,500 events were recorded over an 18 day period. The recorded seismicity provided input for the local-earthquake tomography code, SIMULPS. Eighteen tomograms were generated and high-velocity regions correlated well with high abutment stresses. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated. These results indicate that velocity tomography can be used to provide a better understanding of temporal changes within a rock mass, and can potentially be used to produce a better understanding of the mechanisms that lead to unanticipated ground failures.

Jan 1, 2008

To allow the controlled yielding of mine walls in order to reduce rock-burst hazards and reduce maintenance caused by excessive squeezing forces. Approach Rock bolts that elongate and continue to sustain a load, have been fabricated and tested. This device is an adoption of a concept originally developed in South Africa for use where unusually adverse conditions may warrant the added cost. How It Works A coupling in the rock bolt allows controlled elongation if the load increases beyond the bolt's design strength. (The load can build up either slowly, as during heaving, or rapidly, as before a rock burst.) The elon¬gation of one or more rock bolts surrounding a mine opening, allows the rock to move from its original position to c new position in a controlled manner. This movement relieves the rock stresses, and the mine opening reaches a new state of equilibrium. The elongatible coupling of the rock bolt consists of a

Jan 1, 1977

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (volume III) contains overall injury experience and employment data at bituminous-coal, lignite, and anthracite mines, coking plants, metal and nonmetal mines, metallurgical plants, and stone quarries in the United States for the calendar year 1956. Volume I of the Yearbook includes injury experiences and related employment data in the metal, nonmetal, and quarrying industries, and in the milling operations connected with the mining of those commodities. Volume II contains the injury and related employment experience of the coal mining, coking, and oil and gas industries. Reporting is voluntary on the surveys conducted by the Bureau of Mines to collect injury and employment data in the mineral industries, except in the coal-mining industry, where operators are required by Federal law to furnish the information requested.

Jan 1, 1958

By H. Britton

This bulletin is the seventh in the series of petroleum bibliographies published by the Bureau of Mines, Bulletins 149, 165, 180, 189, 216, and 220 being compilations for the years 1915, 1916, 1917, 1918, 1919-20, and 1921, respectively. In this bulletin the same general plan of classification of references has been followed, but several additions have been made. ACKNOWLEDGMENTS Acknowledgment is made to the following organizations for the use of their libraries in the preparation of this bulletin: University of California, Stanford University, California State Mining Bureau, Union Oil Co. of California, Standard Oil Co. of California, and the Mechanics Mercantile Library of San Francisco; acknowledgment for their assistance is also made to H. H. Hill, C. P. Bowie, A. L. Foster, M. J. Gavin, H. C. Miller, E. B. Swanson, and Miss Louise Janssen, all of the Bureau of Mines, and to Miss Elizabeth H. Burroughs of the Union Oil Co. of California.

Jan 1, 1929

By R. Karl Zipf, Francois E. Heuze

Stress analysis programs such as MULSIM/NL, LAMODEL, MinSim 2000, and EXAMINETAB are used in the mining industry to analyze stresses and displacements in coal mines, platinum mines, gold reefs, and tabular-type deposits. These relatively simple numerical models can efficiently simulate yielding and failure of a rock mass near a mine opening and subsequent stress transfer. The main input parameters for these models are a family of nonlinear stress-strain curves for the in-seam material. For many applications of these models, such as in coal mining, extensive field measurements and observations exist from which to estimate these stress-strain curves and calibrate the numerical models; however, such measurements are lacking for other types of mines. A three-step method is presented to determine nonlinear stress-strain curves for boundary-element (BE) programs used in many mining applications. The method requires a suite of laboratory-scale strength tests at various confining pressures. Note that this analysis uses laboratory-measured strength and modulus properties of alluvium. The dependency of the mechanical properties of alluvium on scale has not been established, although more tests are being planned. However, it is believed that the relative comparisons performed are valuable regardless of scale effects. First, the FLAC2D computer program is used to model the laboratory tests and determine cohesion (c) and friction angle () for a Mohr-Coulomb material model. Second, another FLAC2D model uses the c and values to calculate vertical stress and strain around a single opening in the rock mass. This model calculates the stress-strain path of points at various distances from the opening boundary. Finally, based on these stress-strain paths, the stress-strain curves needed for a BE analysis are derived. This three-step method was demonstrated in a large, flat-lying underground test facility in very weak rock. The BE analyses agreed well with observations of failure at the test facility and provided a basis for evaluating the behavior of alternative layouts.

By Richard W. Knostman

A study was made of the factors affecting lead and zinc production in the Pacific Northwest. Costs, ore reserves and potential resources, and domestic demand were analyzed. It was concluded that a projected 3.1-percent average annual increase in U.S. demand for zinc through 1975 and a corresponding 2.5-percent rise for lead will be supplied mainly from mines in the Eastern and Central States. Annual Pacific Northwest mine production of lead is estimated to fluctuate around 82,000 tons, while zinc output may average 135,000 tons through 1975. Measured, indicated, and inferred reserves in the Pacific Northwest, containing 1.56 million tons of lead and 2.59 million tons of zinc, are more than sufficient to maintain this level of production. Annual production from Pacific Northwest electrolytic zinc plants is expected to increase to over 300,000 tons of slab zinc by 1975. Lead smelters may experience difficulty in maintaining output at 1964 levels.

Jan 1, 1967

By John B. Gayle

The Bureau of Mines has designed and constructed an experimental coke oven, using a commercial oven as a model where practicable. Because the rate of carbonization is important in determining the quality of the coke produced and may affect the "mount of pressure developed during carbonization, particular attention was given to those elements of the design that govern the heat transfer to the charge. The new oven deviates in design from most existing test ovens in that the charge is full width (17 inches), the heating walls ore constructed of 4-1/2-inch silica brick, and zoned, heat-input arrangements compensate for heat losses at the ends, top, and bottom of the charge. This report describes the oven, which was designed by H. S. Auvil and installed under his direction, at the Southern Experiment Station, Tuscaloosa, Ala., while he was supervising, engineer, Coke Section. It gives the results of a limited number of carbonizing tests. These results indicate that the main objective in designing and building this oven, that off duplicating commerical, slot-oven carbonizing conditions, has been accomplished; if coke-discharge conditions simulate commercial-oven conditions, the cokes from the experimental oven arc very similar to oven coke, in soma tests being fully as close is duplicate tests from a Angle batch of coke.

Jan 1, 1952

By Keith A. Heasley, Frank E. Chase, Christopher Mark

Deep cover retreat mining (overburden in excess of 750 ft) is an important emerging issue which will intensify in the future as the more easily mined shallow seam reserves are depleted. Analysis of Mine Safety and Health Administration (MSHA) statistics indicates that deep cover pillar recovery accounts for a disproportionate share of the underground coal mine roof/rib fall fatalities and injuries. Past research has shown that previously recommended Analysis of Retreat Mining Pillar Stability (ARMPS) stability factors (SF’s) may be excessive for deep cover pillar design. The objectives of this study were to evaluate the various methods and strategies by which panels, production pillars and barrier pillars are developed and extracted under deep cover, and to develop appropriate design guidelines. In the course of the research, 29 mines in 7 states were investigated to collect panel design case histories. At each mine site, underground geotechnical data were collected on the pillar line in order to document roof rock, coalbed and floor conditions. The analyses indicated that squeezes were the most likely failure mode where the depth was less than 1,250 ft, but bumps predominated in the deeper cover cases. Immediate roof rock quality, the ARMPS SF’s, and barrier pillar stability factors were all found to be important parameters in determining the outcomes of the case histories. Design guidelines, including suggestions for barrier pillars to isolate active panels from nearby gobs in bump prone ground, are also proposed.