Search Documents

By Don Belsher

Work on contract H0272007 is summarized for the period of 1 February 977 to 1 February 1978. The initial evaluation of two potential systems for the location of well casings, voids, and tunnels in coal are described. The pulse measurement equipment used for the evaluation of the antennas selected possible use with a pulse time domain system and an FM-CW system is described. A TEM horn antenna design potentially suitable for use with these systems is given. An operational comparative analysis between various antenna types is presented.

Jan 1, 1978

By E. D. Palmes

Phase I of these studies demonstrated the feasibility of measuring the efficiency and capacity of sorbents in tube-type samplers for contaminant gases. This was accomplished by measuring concentration at various points along the length of the diffusion path during sampling. Concentrations were measured by removing small aliquots with gas-tight syringes and gas chromatography. With hexane as the gas and activated charcoal as the sorbent the procedure was quite successful and we proceeded with Phase II of the study; this involved application of the principle to gases of importance in diesel exhaust using a variety of sorbents. When we worked with high concentrations of the test gas we clearly demonstrated the differences in both efficiency and capacity of the sorbents for each of several gases. The chief drawbacks of the system were that we were unsuccessful in determining more toxic gases at realistic occupational exposure levels or determining formaldehyde at any level using the flame ionization detector. It was concluded that, although the method is feasible, more sensitive methods of measuring concentrations of gas in the tube must be developed to make the procedure applicable to regions of chief industrial hygiene interest.

Jan 1, 1983

By Sean Gallagher

Bolting large sheets of wire mesh screen (WMS) to the roof of underground mines prevents injuries due to rock falls. However, WMS can be heavy and awkward to lift and transport, and may result in significant spinal loading. Accordingly, six male subjects (mean age =45.8 years + 7.5 SD) were recruited to lift WMS in a laboratory investigation of the biomechanical demands. Biomechanical modeling was used to estimate external moments about L5-S1 for sixteen lifting tasks, using two sizes of WMS. Full-size WMS involved a two-person lift, while half-size WMS involved a one-person lift. Lifts were performed under 168 cm and 213 cm vertical space. Restriction in vertical space increased the maximum L5-S1 extensor moment from 254 to 274 Nm and right lateral bending moment from 195 to 251 Nm. Lifting full sheets of screen (as opposed to half sheets) resulted in an average 33 Nm increase in L5-S1 extensor moment. The L5-S1 extensor moment was increased by an average of 44 Nm (18%) when lifting screens positioned flat on the floor compared to an upright position. Relevance to industry: Large flexible materials are commonly lifted in industrial work environments, and may involve the efforts of two or more workers. The current study examines the low back loading associated with lifting large flexible screens and presents recommendations to reduce spine loading.

Jan 1, 2009

By Alan A. Campoli

The U.S. Bureau of Mines evaluated two different conventionallongwall gate entry systems in the Southern Appalachian Basin, where mining and geologic conditions are conducive for coal pillar bumps. These gate entry systems were in a coal mine located in the Pocahontas No.3 Coalbed under approximately 2,000 ft of overburden and a massive quartzite sandstone member, and both employed a center abutment pillar flanked by yield pillars. The 8O-ft-square tailgate abutment pillars within the first study area began bumping 500 ft in advance of mining. This was accompanied by face bumps on the tailgate corner of the longwall face. The 120-by 180-ft tailgate abutment pillars within the second study area did not begin to bump until mining was approximately 100 ft past. Coalbed stress change and abutment pillar dilation data demonstrated that a 15-ft-wide perimeter of yielded coal surrounded a highly stressed core in both sizes of abutment pillars. The 62 pet more core area per foot of gate entry in the larger abutment pillars prevented excessive load transfer to the corner of the tailgate panel and eliminated the face bumps experienced with the original gate entry design.

Jan 1, 1990

By L. J. E. Hofer, J. L. Snyder, J. N. Barn, J. E. Chilton, W. E. Thomas

Various silicone materials have been proposed for use in mining environments. The catalytic methane sensors now employed are poisoned by silicone vapors. Activated charcoal and carbon cloth adsorbents will increase the sensor lifetimes in an environment containing significant silicone vapor concentrations. The results of a study of catalytic methane sensor operation with adsorbent materials in hexamethyldisiloxane-air mixtures are reported. Sampling techniques developed for measuring silicone vapor content of mine atmospheres are described.

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the fuel-briquet and packaged-fuel producers in the United States and publishes economic data on these industries, based upon reports submitted voluntarily by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all producers of processed minerals fuels. A few small plants may not have been canvassed or failed to respond to the survey because some of the smaller plants operate intermittently and the survey is voluntary. All plants that reported commercial production were included; regardless of size. Specifically excluded were plants that manufactured briquets from wood charcoal. Fuel briquets and packaged fuel are manufactured solid fuels, produced by mixing fine-sized mineral fuels with binding materials and compressing into small individual shapes, Briquets are produced in pillow-shaped and cylindrical form, are 2 to 4 inches long, and weigh 2 to 4 ounces. Packaged fuel consists of 3- or 4-inch cubes; 6 or 8 of which are wrapped together in heavy kraft paper to form a package weighing 10 to 15 pounds, Briquets are durable and may be stored and handled as bulk fuel; packaged fuel breaks easily and must be stored indoors to prevent it from deteriorating. Whereas briquets are consumed in many areas as a general residential fuel, packaged fuel is more of a specialty item, used at times to supplement other fuels. Packaged fuel is burned without re-moving the paper and is referred to as the "white glove" fuel.

Jan 1, 1961

By Roger M. Turpening

This study was performed to examine the feasibility of using seismic shear waves to detect the presence of abandoned coal mines. !he Antiquity Coal Mine near Antiquity, Ohio was used as a region of known voids. No attempt was made here to accurately locate the mine tunnels if detection was obtained. The results of this study were positive. Sharp changes in the amplitude of the received shear waves were clear indications of the presence of a fluid (gas or liquid) filled region between the source and receivers. When moving the source showed no change in the received signals it was concluded that the voids existed beneath the sensors. Prior to these tests drilling (SM-3) had determined that a void did exist in this area. This void was confirmed by this shear wave test and two additional voids were found.

Jan 1, 2012

By Donald F. Reed

Deposits of gray hematite occur in two districts in Talladega County, Ala., the Emauhee-Tallasechatch and Weewoka, both in the; vicinity of Wintorboro, 50 miles east of Birmingham. The deposits were investigated by the Bureau of Mines in 1945 and 1944. Approximately 15,000 feet of diamond drilling was done and 6,000 linear feet of trenches excavated and sampled.

Jan 1, 1949

By J. A. Kosek

Work has been conducted under Bureau of Mines Contract Number HO 357078 to develop instruments for detecting CO, NO and NO2 in a mine atmosphere, using fuel cell technology. The approach has been to optimize the fuel cell sensor configuration for the specific detection of CO, NO and NO2 in the presence of other mine gases utilizing recent advances in catalyst, electrode and solid polymer electrolyte membrane technology. Para-metric testing has been conducted on three electrode sensor cells to define performance and life characteristics as a function of temperature, feed flow and applied sensor voltage. Extended life testing has been performed on sensor cell configurations exhibiting favorable characteristics. Reliable, efficient gas sampling and electronic control circuitry has been fabricated for use with the sensor cells, and integrated into devices to meet the performance and design specifications for portable, battery-powered, hand held direct indicating gas detectors for use underground. Twenty of the production-type, direct indicating CO detectors have been tested and delivered to the Bureau of Mines under the present contract. Three prototype diffusion head CO monitors have also been delivered for evaluation under the pre-sent contract. The gas sampling pump and related parts have been replaced by a diffusion tube assembly in which CO reaches the sensing electrode surface by diffusion alone. In addition, delivery will be made of ten direct-indicating nitric oxide detectors and ten direct-indicating nitrogen dioxide detectors. These instruments are very similar in design to the direct indicating CO detector.

Jan 1, 1979

By J. W. Adams

Two different techniques were wed to make measurements of the absolute value of electromagnetic noise in an operating hardrock mine, Grace Mine, located near Morgantown, Pennsylvania. Diesel-powered haulage equipment is used in this mine, and the electromagnetic noise environment it creates was measured to see how it differs from the environment created by electric-powered haulage equipment. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. Data are recorded using broadband analog magnetic tape and are later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and in amplitude probability distribution plots.

Jan 1, 1974

By Clark F. Grain

These investigations were undertaken as part of the Bureau of Mines program for the development and evaluation of high temperature nonmetallic materials. This report consists of thermal expansion and phase inversion measurements by high-temperature X-ray diffractometry on the principal oxides of beryllium (BeO), calcium (CaO), titanium (TiO2 ), zirconium (ZrO2 ), hafnium (HfO2), and thorium (ThO2); all were high-purity commercially available oxides. Thermal expansion values were calculated from unit cell dimensions measured at selected temperatures. Expansion was determined parallel to each major crystallographic axis for the anisotropic oxides: BeO, TOi2, ZrC2, and HfO2. Combined random and systematic errors in the thermal expansion values are considered to be less than 3 percent of the total expansion at 500° C. and approximately 2 percent at 1,000° C. No hysteresis in the expansion curves was noted between heating and cooling cycles. The Bureau's values were compared with published expansion measurements obtained by X-ray diffraction, dilatometric, interferometric, and telemicroscopic techniques. For anisotropic oxides, average linear expansion values were calculated from the volume expansion.

Jan 1, 1962

By K. P. V. Lei

The Bureau of Mines investigated molten-salt electrorefining as a practical method for reclaiming vanadium from vanadium scrap. An electrolytic process utilizing a KC1-LiC1-VC12 electrolyte at 615° C was developed for producing ductile vanadium with a purity over 99.9 percent. The recovery of the vanadium in the cell feed ranged from 88 to 93 percent with a current efficiency from 83 to 95 percent.

Jan 1, 1967

By J. F. McIlwain

The Bureau of Mines has investigated fumes generated by selected welding electrodes used in mines in order to help determine their relative health hazard potential. Fumes were generated and collected in an enclosed chamber for subsequent generation rate and chemical constituent determination. Shielded metal arc electrodes from the following groups were tested: AWS types E308-16 and E310-16 stainless steel, ECoCr-A Co-Cr hardfacing alloy, ENiCr Ni, an Mn-Cr buildup alloy, E7018 carbon steel, and EII018-M low-alloy steel. Flux-cored wire electrodes of this last group also were tested. Fume generation rates and the chemical composition of the fumes were measured. From these data, exposure in-dices were determined, which give a relative measure of the health hazard potential of using the electrodes. The effect of welding onto build-up alloy layers on the fume composition also was examined for five of the higher alloy groups.

Jan 1, 1987

By S. L. Crouch

An important class of mining problems involves excavations in planar seam or vein-type deposits. In many instances it can be assumed that the seam is at 'infinite' depth in a homogeneous, isotropic or transversely isotropic, linearly elastic rock mss, and that the normal to the plane of the seam is a principal stress direction. Rational planning of excavations in such deposits requires a knowledge; of the stresses and displacements induced by complicated, irregular excavation geometries in the plane of the seam. This problem previously has been solved either numerically or by means of an electrical resistance network analog. Both of these methods effectively simulate the mined portions of the seam as a dislocation in an otherwise continuous mass, and determine the complete solution in terms of the stresses and displacements at the seam. In both cases, the plane of the seam is divided into a number - say, M x N - of squares, and the solution to the problem is determined in terms of the solution to an M x N system of equations. The numerical approach requires that these equations be solved explicitly, while the analog; solves them instantaneously with current analogous to stress and voltage to displacement. A purely numerical solution of practical problems can require a substantial amount of computer time, particularly in situations that demand some sort of sequential analysis, either due to successive mining or to nonlinear behavior of the seam material. This report describes a combined analog-digital computer system for solving problems that are impractical when either device is used separately. The digital computer and the analog are interfaced so that the digital computer can receive information from the analog via a switching matrix and an analog to digital converter, and can activate points of the analog via another switching matrix and a set of digital to analog converters. The resulting hybrid system can be used to simulate arbitrary "stress-strain" characteristics for any portion of the seam by an iterative procedure similar to the initial strain method used in nonlinear finite element analysis. Thus, the hybrid system combines the speed of analog computation with the decision-making capability of the digital computer: the analog instantaneously solves the set of equations, and the digital computer decides how the initial strains must be altered for the solution to be compatible with the prescribed "stress-strain" characteristics for the seam material. The hybrid computer system has many implications for rational planning of underground excavations, since it allows practically any type of inelastic seam behavior or artificial support characteristics to be simulated. Inelastic seam behavior, for example, might be due to either rock failure or to time-dependent deformation.

Jan 1, 1974

By E. C. Tarpley

An acid-extraction procedure developed in Germany for determining mineral matter in coal was investigated by the Bureau of Mines to determine its application to American coals. It was found to be suitable for all ranks of coal from anthracite to lignite if modified slightly for coals containing considerable quantities of calcium compounds, such as calcite or calcium humate. The precision of the method is satisfactory, and the results are probably closer to the true content of mineral matter than those obtained by empirical formulas. The method requires considerably more analytical data than the Parr or approximation formulas but is no more time consuming than obtaining the necessary data for the King, Maries, and Crossley formula (theoretically the most comprehensive empirical formula used). An appendix to this report includes a detailed description of a recommended procedure.

Jan 1, 1959

By Llewellyn A. Rubin

Under Bureau of Mines Contract H0122007, Telcom, Inc., with the assistance of Fenix & Scisson, Inc., conducted a 17-month research and development project aimed at provid¬ing a field-test model of a guidance system for use with the Bureau of Mines Probe Drill. The Probe Drill is a part of the Bureau's Mine Rescue System developed under Contract H0101262. Volume I of this report is subdivided into seven sections. Volume II consists of a number of supporting appendices. In addition, there were delivered under the Contract, a number of other documents which are referenced in the text. Section 1 deals with essential contract information, Program Background, and a general system description. Section 2 covers the project chronology in brief. Section 3 is a digest of design considerations and implementation related to the requirements of the Contract. Section 4 is a description of the System, including illustrations of the hardware, and software. Section 5 is devoted to Operation and Maintenance. Para. 5.1 describes step-by-step field assembly and disassembly of the downhole unit. Para. 5.2 covers Operation. Para. 5.3 covers various aspects of maintenance from the lowest field echelon possible. Higher level maintenance must be accomplished in the laboratory, for the present field-test model. Para. 5.4 covers system calibration. Para. 5.5 covers detailed step-by-step operational sequences. Section 6 covers the results of the field testing, post-test evaluation, and recommendations. Essentially, we conclude that the present hardware (field-test model) has proven every aspect of system performance, but failed to provide reliable assurance of an operationally ready system. Telcom, therefore, recommends a three-phase continuing effort devised to provide the operationally-ready model of the system.

Jan 1, 1973

By Thomas Novak, Jeffrey L. Kohler, Joseph Sottile, Steve J. Gnapragasam

Modern underground coal mines can be very large, having a total connected load in excess of l5 000 hp. These mines generally have many miles of high-power conveyor belts and 15 or more miles of high-voltage power cables at distribution voltages of 12.47, 13.2, 13.8, or 14.4 kV. The shielded cables used in mine power distribution systems have a significant level of capacitance, on the order of 110 pF/ft. This level of capacitance, in an extensive power distribution system at today's voltage levels, can cause significant charging currents during a ground fault. This paper addresses the potential detrimental effects of capacitance charging currents during line-to-ground faults in mine power distribution systems. A representative mine power system is modeled, and simulations with faults at various locations are conducted to evaluate the effects of this capacitance on the level of fault current and relay selectivity. This paper also includes results of capacitance measurements made on mine power feeder cables used to validate the simulation model.

By E. B. Kester

Of the many angles from which coal can be studied it is evident that some have a direct and others have only an indirect bearing on its physical or chemical nature . The more drastic the treatment employed in an investigation , the more inferential become the conclusions permissible from the experimental evidence obtained . Thus , ultimate and proximate analyses tell something concerning age , behavior on carbonization , and possible industrial usefulness , but nothing regarding structure or composition in the larger sense . Strong oxidation reveals the fact that benzenoid , pyrrol , and furane rings are prevalent in the chemical substances present , and milder oxidation indicates that the mass of coal , as in the case of the peats and lignites , is humic in character . But beyond such points of information , very little additional can be gained by the use of these more or less vigorous measures . To gain wider knowledge of the actual constituents of coal substance as found investigators have worked out systems of separation by means of solvents , of which a large number have been employed at various times both singly and in combination . The list of solvents includes petroleum ether , benzene , toluene , xylene , ethyl ether , alcohol , acetone , carbon bisulphide , pyridine , quinoline , aniline , phenol , tetralin , glycol ethyl ether glycol ethylether acetate , glycol methyl ether , glycol diethyl ether , pine oil , mesityl oxide furfural , benzaldehyde , ethylene oxide , rosin , caustic potash in solvents , amyl alcohol plus pyridine , chloroform , carbon tetrachloride , acetylene tetrachloride , naphthalene , and others . Once a coal has been extracted it has become common practice to subdivide the extract by means of partial solution in other and weaker solvents . Thus , we find the oily and solid bitumens of Fischer ( 1 ) , 3 Bone ( 2 ) and others ; the alpha , beta and gamma constituents of Wheeler ( 3 ) ; the classification of Novak and Hubacek ( 4 ) embracing oils , resins A , resins B , bitumens An , bitumens Bn , and bitumens Cn ; Crussard's ( 5 ) malthenes , asphaltenes , and carbenes , borrowed from asphalt terminology; and the 40 or more subdivisions of the phenol extract of coal worked out by Frazer and Hoffman ( 6 ) . Perhaps the primary object of interest in these many researches has been to find the coking principle of coal , and to study it and to learn why certain coals form hard , wellfused cokes , and others merely fall to pieces during carbonization . The origin of the various constituents of the gas and tar , the temperature at which each forms , and something of the mechanism of their synthesis have also been sought , as well as new bases for adjudging rank .

May 1, 1931

By John P. Borovsky

A 3-year study was conducted to evaluate the problems and benefits of using vegetation to stabilize tailing from a potential Minnesota copper-nickel milling operation. The project consisted of three separate investigations: a waste characterization study, a greenhouse study and a field study. With few exceptions, the physical and chemical characteristics of the tai ling were found to lie within the range of properties of Minnesota soils. The tailing lacks organic matter; is deficient in nitrogen, phosphorus and potassium; and may contain elevated levels of soluble salts and heavy metals, particularly copper and nickel. Numerous grasses, forbs and woody plants will tolerate the tailing as a rooting medium. Peat incorporation and topsoil dressing provided few benefits to the revegetation process which were not provided by a fertilizer application. With fertilization, grass/legume production in the tailing was comparable to local agricultural yields. Concentration of heavy metals in grasses grown in the tailing were generally below suggested tolerance limits for plants and animal forage. Legumes tended to accumulate higher concentrations of copper and nickel, and metal uptake of most plants was positively correlated with rate of fertilization. Tailing drainage water contained elevated levels of heavy metals, and establishment of vegetation had little effect on the quantity and quality of tailing drainage water. However, topsoil dressing significantly increased drainage water volume when compared to unvegetated control plots. Copper-nickel tailing revegetation recommendations were developed.

Jan 1, 1983

By Douglas W. Fuerstenau

A detailed experimental study of breakage kinetics in a batch rod mill indicates that while the system is inherently nonlinear, the feed disappearance kinetics for the finer sizes and the coarser sizes at high holdups is well represented by first-order behavior. The set of breakage distribution functions was found to be normalizable and independent of particle holdup in the mill. The size discretized initial breakage rate functions were found to be inversely proportional to particle holdup and almost directly proportional to particle size. A linearized grinding model that results from the first-order Taylor's series expansion of the breakage rate expression was found to give good simulations of the mill product size distributions without recourse to any parameter improvement routines. Material transport through rod mills was evaluated by investigating the effect of operating variables on the holdup and residence time distribution of particulate solids flowing through the mill. Identical experiments performed in a continuous ball mill helped delineate the fundamental differences in particulate transport through these two types of mills. Mechanistic interpretations of the observed transport phenomena are presented, and their implications in the context of tumbling mill analysis and design pointed out.

Jan 1, 1980