Search Documents

By Jorge Cárdenas, Gustavo Huerta, Regina Rocha Oriundo, Miguel Angel Humpire, Johan Salas Flores

Currently a critical activity for slopes stability and safety in mining is pre-split blasting to reduce damage from trim blast. Most common explosive used are based on packaged explosives, with 1 ½ in diameter cartridges initiated by detonating cord. Traditional loading process requires a significant amount of trained personnel, which in our application context could take up to 20 blasters. When pre-split blast is scheduled, it usually reduces the availability of the blasters on the total loading services at site which are also demanded to have production blasting ready at same 12-hour shift daylight time.

Feb 6, 2023

By Doug Johnson

This paper reviews the field implementation of R & F Coal's blasting optimization work concerning analysis, prediction, and control of overburden blasting vibrations using site specific measurements and state-of-the-art computer technology. Blasting personnel at R & F Coal had the opportunity to work jointly with Otto Crenwelge of Shell Development Company in his test studies and to later be instructed in the procedures involved in optimizing vibration frequency.

Jan 1, 1988

By E. Contestabile, B. von Rosen, P. Lightfoot

As part of an accident investigation ANFO was subjected to various abusive tests. A tractor-trailer carrying 18,000 kg of blasting explosives, caught fire, burned for approximately 30 minutes, and then detonated. A series of tests was designed to observe the behaviour of ANFO when subjected to different thermal stimulus tests and more specifically, the Height-to-Detonation Test. Three diameters of steel pipes were used in the Height-to-Detonation Tests thereby simulating cylindrical columns within a pile of ANFO. The ANFO samples were then subjected to various thermal stimuli to initiate a reaction. Through the use of some instrumentation, the response of large ANFO samples was recorded and its behaviour, including the occurrence of phase changes will be analysed.

Jan 1, 2001

By Bob de Raadt

After a review of the general principles for blasting stacks, the stagnations of two stack demolitions are investigated. The author concludes and demonstrates that MS-delay blasting can be risky under certain circumstances. How this initiation device can still be applied safely to the demolition of stacks is shown in an account of a blasting operation, in which two 106-m (350 ft) -high concrete stacks were involved. The recent discovery of a possible hazard of MS initiation in this field of blasting is an essential contribution to increased safety in blasting tall structures.

Jan 1, 1982

By Alton Dunaway, Kevin Sullivan, Charles Gray, Doug Hall, Kevin Grant, Kelly Thiel, John Paulson, Bruce Leland, Cole Boyd

Beaver (Castor canadensis) are responsible for economic losses exceeding $4 billion over the last 4 decades in the southeastern United States alone. A large portion of these damages occurs to public roads and highways, forests, agricultural resources, and other property from flooding caused by beaver dams. The United States Department of agriculture, Animal Plant Health Inspection Service, Wildlife Services (WS) program is a non-regulatory Federal program directed by Congress to assist resource owners with managing damage caused by wildlife.

Jan 1, 2007

By Robert B. Hopler

The hazards which naturally prevail in underground coal mines, always severe and unpredictable due to the loosely-consolidated strata in which coal is frequently found, are increased by the commonly-occurring combination of coal dust, methane, and explosives. It was recognized by the mid-nineteenth century that coal dust was the basic factor contributing to disastrous explosions killing hundreds of miners, and that the ignition of methane gas was often the source of the coal dust explosions. It was apparent that preventing the ignition of methane was a critical part of avoiding these disasters, and it was also apparent that one cause of such ignitions was the firing of explosives. In addition, it was found that dust explosions were often initiated by blown-out shots of explosives in the absence of methane.

Jan 1, 1996

A major problem that has continued to plague the surface coal industry is blast induced damage to the coal seam. Atlas Powder Company has addresssed this situation through seven years of field research in full-scale production environments. Many operations across the United States have been evaluated.

Jan 1, 1990

By Evan Jannoulakis, Wilfrid Comeau

Using the Scaled Distance (SD) and the vector sum Peak Particle Velocity (PPVvs) from a single delay, preferably single blasthole, in a shot, a number is derived which has shown itself to be consistently related to blasting efficiency, as experienced by one of the authors of this paper over the last thirty years. The numbers derived by this process range in value over one order of magnitude more or less. This variation, a function of distance, weight of explosive in the delay, blasthole diameter, blast design, powder factor and the geological environment, can be consistently related to two of these factors, powder factor and distance. In actual use the measured "BED" representing good blasting results should not vary by more than + 33 to + 50 percent of the estimated "BED" in non calibrated cases, and + 10 to 20 percent where previous experience is available. Relatively high "BED" values are indicative of poor blasting results while relatively low "BED" values may be precursors of poor blasting results in a shot. There are many variables in the geological environment which can affect the "BED". A case study is presented from a surface coal mining operation in eastern Canada. This case study tries to evaluate the reasons for the variability in "BED" values derived from multi-hole shots. A problem in using "Signature Vibrations" from a single-hole shot to predict blasting vibrations from multiple-hole production shots is identified.

Jan 1, 1998

By Jody Todd, Ernesto Villaescusa, Ronald Lachenicht, Kelly Fleetwood

In the underground environment, characterisation of a rock mass during the mining cycle becomes increasingly difficult due to a lack of rock mass exposure for measurement or observation. In most cases rock mass characterisation occurs prior to mining by inspection and logging of exploration drill core, or prior to mass excavation through drive mapping for geological and geotechnical data. Characterisation strategies, if applied during the mining cycle, can reveal near-field anisotropies that may affect the behaviour of the rock mass with respect to excavation. These methods can aid in understanding the performance of stopes based on geometry, in-stope extraction sequence, and stress modelling. One such method of characterisation involves the use of production blast vibration monitoring and analysis as indicators of rock mass anisotropy through travel-time tomography.

Jan 1, 2008

By BruneJurgen F., Richard C. Gilmore, Matthew Schreiner, Ray Johnson

Explosive pockets of methane-air mixtures accumulate in underground coal mines and, when ignited, produce an air-blast wave that can disturb combustible coal dust on the floor, roof, and ribs. To prevent explosions, the coal dust must be continuously diluted through application of inert rock dust, usually powdered limestone. Application of powdered dust process creates a respiratory nuisance downwind, where miners cannot work until the dust settles. Rock dust suppliers have developed wet and foam applied products to reduce the nuisance and limit the interruption to mining during dust application. To test the effectiveness of these alternative dust products, researchers at the Colorado School of Mines (Mines) have constructed a full-scale explosion test drift located at the Mines Edgar Experimental Mine (Edgar) to study the dispersibility of different rock dust applications. This paper examines the use of Pentaerythritol tetranitrate (PETN) detonating cord to produce controlled air-blasts that simulate methane-air explosions. The air blasts are generated with curtains of detonating cord that produce shockwaves with wind speeds between 30 to 70 m/s (100 to 225 fps) depending on the length of 5.3 g/m (25 grain/ft) detonating cord used. These velocities represent the minimum air speeds required to trigger propagating coal dust explosions. Researchers have conducted 40 test blasts with various lengths of detonating cord. Results show the two primary waves and two reflected waves each decaying into airblast waves with overpressures of 14 to 27 kPa (2 to 4 psi). Pressures were recorded with commercial piezoelectric transducers and custom-built, bi-directional probes to record the total and dynamic pressures of the wind generated in the explosion. Researchers were able to generate consistent and repeatable wind speeds and air-blast durations sufficiently similar to a methane-air explosion to study the dispersibility of various rock dust products and application methods

Jan 1, 2019

By G. Walsh, M. T. Wild

In this paper the performance effects of linear shaped charges will be discussed. Different sized charges were tested and reviewed based on their performance used with a typical detonation method vs. detonation with a line wave generator. The goal of the project was to determine if the linear shaped charge had better performance with an ideally linear wave moving through it, verses a swept wave that is currently used. A line wave generator is a flexible sheet explosive formed into a triangular shape with holes placed in strategic places to cause a detonation wave to become linear across the width of the triangle. A standard linear shape charge with a detonator in the side of the charge was be detonated against a witness plate to get a standard depth of penetration. A second standard linear shape charge with a detonator connected to the top of a line wave generator, the line wave generator placed on top of the linear shape charge, was be detonated against a witness plate to get a comparison depth of penetration. All charges had a standoff 1.5 times the width of the cavity, allowing the data to be compared to the control charge. Computer modeling was intended to be used to predict the results from testing these designs in the field. The actual results were compared among themselves.

Jan 1, 2011

By Javier Illanes Pizarro, Gustavo Huerta Valer, Jorge Cárdenas Miranda

Bench stability is the basis of sustainability in an open pit mining operation. Taking care of the pit walls while maintaining fragmentation results can prove a challenge. In this study, technical proposals have been developed for extra hard rock mass (UCS>175MPa) with presence of unfavorable structural planes in high copper grade zones. The base case shows low compliance of fragmentation results and a significant loss in berm width, with over size boulders causing low primary crushing rates. Paradigms in current drill and blast design were overcome to improve fragmentation results and achieve objectives.

Feb 6, 2023

By Jorge Cárdenas, Diego Gamarra

In previous phases of the mine, a landslide resulted in several losses in production delays. The stability of slopes in a mining operation is critical for the sustainability of the operation, as they are exposed to vibrations and damage caused by blasting. Therefore, it is essential to implement controls and innovative technologies to reduce these vibrations levels. This study focuses on the application of low-energy emulsions with lower densities than conventional explosives, developed to reduce vibrations and the energy delivered to the rock mass adjacent to the near blast holes as a buffer row. Near field studies were carried out by embedding triaxial geophones. Vibrations were recorded, and mathematical models of vibration associated with different types of explosive mixtures were generated. This allowed us to determine the benefit of implementing low-density explosives in reducing vibrations compared to Heavy ANFO explosives. The application of low-energy explosives with densities ranging from 0.7 to 0.8 g/cm³ and Relative Bulk Strength (RBS) of 51-65 allows for a 40% reduction in vibrations compared to the detonation of Heavy ANFO explosives.

Jan 21, 2025

By Gordon C. Petersen, Gary A. Almeraris

This paper describes the controlled blasting techniques required to mine a rock tunnel section of a main interceptor located in the Boston Metropolitan area. The 3m (10 ft) x 2.8m (9.25 ft) horseshoe shaped tunnel was driven 490m (1600 ft) by conventional drill and blast methods. The geology varied round by round and consisted of five highly faulted and jointed igneous rock types. The tunnel intersected numerous slickenslides and open mud seams which hampered both drilling and loading operations. Smooth blasting wee critical in order to keep overbreak tc a minimum in this extremely hard but blocky ground.

Jan 1, 1991

By THOMAS BAMFORD, Dale S. Preece, Amir Behbahanian, Mick Lownds

An important aspect of blasting is rock movement and final muck configuration. Computer modeling of this process has been done in 2D for many years, revealing insights into the blasting process and enabling some design optimization. Since blasting is inherently a 3D process, 2D modeling misses the 3D aspects of blasting results and can lead to inaccurate conclusions. Software development environments in many fields are evolving in 3D, enabled by steadily increasing computer speed, memory, and software efficiency. These same environments are also available for modeling of many physical processes, including rock blasting. This paper documents the development of 3D blast movement modeling techniques that utilize 3D computational mechanics and modern computing environments to predict explosive induced movement of hundreds of thousands of distinct cubic elements representing the rock mass. Blast induced ore travel and final location can now be predicted with reasonable accuracy and acceptable run times. The importance of Energy Partitioning was documented and demonstrated by GEM-2D (Geologic Element Motion) at the ISEE conference in 2024. This software is titled GEM-3D and includes this Energy Partitioning capability. This paper documents a GEM-3D example of ore movement during rock blasting and demonstrates ore dilution as well as the final location of different rock types as influenced by the blast.

Jan 26, 2026

By Josh Calnan, Paul M. Holmgren, Abigail N. Styer

Detonating cord is a staple of the explosives industry, used widely in the civil and defense industries. Detonating cord is a thin, flexible plastic tube filled with pentaerythritol tetranitrate (PETN). It has many applications in mining, construction and military disciplines. For civil applications, it is used to connect and initiate a series of blastholes in a desired pattern. In the defense sector, it can be used as a detonating agent, a priming agent or alone as an explosive charge. Research has been done to understand the initiation and detonation physics on the detonating cord. However, its sympathetic detonation characteristics needed to be further analyzed.

Feb 1, 2020

By Keith Henderson

An open pit quarry operation in West Central Illinois provided a challenging proposition regarding the removal of a rock wall that once separated two pits, but was now in the middle of the north wall of the combined pit. Their mining plan included the development of a new ramp into the quarry pit in order to lessen the slope and to shorten haul truck cycle time. The task would be to remove a section of rock left behind from mining operations more than 20 years ago that was at or near the bottom of the designed ramp.

Jan 1, 2012

By Gary Cavanough

The spontaneous exothermic reaction of ammonium nitrate explosives with sulphide-containing rocks, commonly referred to as reactive ground, is a site-specific condition that can lead to spontaneous detonations. Mine sites typically carry out regular assessment of ground for reactivity. In Australia, reactive ground testing is conducted according to the Australasian Explosives Industry Safety Group (AEISG) Code of Practice. This paper presents a new method to assess reactive ground. The new method can be completed on the mine site or in the laboratory. The new method allows samples to be tested in hours not weeks, as required when using the method prescribed in the AEISG Code of Practice. The new method also provides an explanation of why ground is reactive or not reactive, Whereas the AEISG Code of Practice provides a reactive, not reactive or marginal results with no understanding of reason for these results. Case studies on the use of weathering agents, pH, sulphide content and carbonate content will be reported. These case studies identify instances where the testing as per the AEISG Code of Practice provides false positive and false negative results. A false positive result will require the use of inhibited products when they are not actually required which increases costs and reduces productivity due to the need to used multiple explosive products. A false negative result increases the risk of an unplanned initiation of a blast hole.

Feb 6, 2023

By Braden Lusk

The problem of predicting damage in densely developed areas due to incidental or malicious explosions is one of considerable importance to local, state, and federal governmental bodies. The difficulty of making such a prediction is confounded by the urban canyon phenomenon as the shock wave intensifies or rarefies depending upon the particular arrangement of buildings. The specific method detailed herein used a Computational Fluid Dynamics solver, ANSYS AUTODYN, to operate on Geographic Information Systems data, ArcGIS, which captured the geospatial relationship between the various buildings in downtown Oklahoma City, prior to the Murrah Building bombing. The model of Oklahoma City was first developed using the building footprints and elevations provided by the ArcGIS database. Due to the sheer size of the problem, the model was then subdivided into annular zones of increasing distance from the center of the blast. Each subsection was then solved using an Euler model in a cascading fashion with the output of the preceding model forming the input of the present model. To further reduce computational time, the size of the Euler nodes was increased at each stage as the section area increased. Due to the loss of precision in capturing peak pressure values when using larger size nodes, it was necessary to perform a transformation on the results using one dimensional wedge calculations with higher precision. The Murrah Building bombing event was an excellent case study due to its available ArcGIS data and the level of documentation of damage to surrounding structures due to the blast. The results from the staged CFD calculation were then used to develop a damage potential contour map. The documented incidents of damage in the area surrounding the Murrah building were then compared to the model generated damage potential contour map. Copyright ©

Jan 1, 2010

By K. Taylor

In surface coal mining, the performance of a shovel through blasted muck is one of the key performance indicators of the blast. Historically, performance has been measured qualitatively based on operator feedback or visuals of the muckpile. More complete shovel data, such as loading times and GPS location, is available from most fleet dispatch systems that are already in place at most truck and shovel operations. With some database and analysis skill, the drill and blast team can take advantage of this data to make targeted improvements to drill and blast designs. An area typically known to cause trouble for shovel operators at this operation are blast boundaries. Blast patterns with and without design changes along the boundaries were studied in this case study. The instantaneous loading times for each shovel pass were analyzed for 75 blasts across two subsequent benches with similar firing direction and shovel paths. The benches were split into three categories: Main body of pattern, boundary with design change, and boundary with no design change. The loading times from the main body of the patterns and where the design change was utilized in the boundary had similar prevalence of good loading times. However, boundary areas without the deign change had approximately 2% more prevalence of poor loading times compared to the main boundary of the pattern. Improving the dig rates through the boundaries up to the average loading time would result in approximately 280 hours taken off the total loading time for one bench. By quantifying the shovel’s performance by GPS location, the drill and blast team can decide how much of a design change is needed, can target precisely only the areas that require it and measure the impact of any changes made

Jan 1, 2024