Search Documents

By Jelena Milinovic, Sofia Martins, Anna Lichtschlag, Sven Petersen, Fernando J. A. S. Barriga, Bramley Murton, Adeline Dutrieux

"The active TAG hydrothermal mound is one of the largest and better studied. Due to its size (one of the largest, known so far, in the Atlantic Ocean) and concentration of specific economic valuable elements, it might be considered for future exploitation due the increasing demand for raw materials. However, the discovery of several large inactive sulfide mounds, some partially buried under sediments may relieve this pressure. Exploration for such occurrences can, together with geophysical exploration tools, be accomplished by mineralogical and geochemical studies of those sediments.INTRODUCTION AND GEOLOGICAL SETTINGThis study reports the results from sediment samples collected during the Meteor M127 cruise on the TAG hydrothermal area in 2016. The Trans-Atlantic Geotraverse (TAG) hydrothermal field (Mid-Atlantic Ridge, 26°08’N) is located 2.4 km east of the main rift valley at depths of about 3650 m. The TAG hydrothermal field stands as an example of a massive sulfide deposit on a low-spreading ridge associated with an active detachment fault (Humphris et al., 2015).Associated with the TAG hydrothermal field are metalliferous sediments/deposits that can reach several meters in thickness (Metz et al., 1988). These sediments/deposits can be formed by hydrothermal plume fall out (buoyant and nonbuoyant), massive wasting of hydrothermal edifices (sulfide mounds and chimneys) and authigenic mineralization (Gurvich, 2006). By studying the grain size, mineralogy and geochemistry of the sediments it is possible to identify each type of sediments and find their proximal or distal distribution. The location of the gravity cores studied here is distributed along sediment ponds near inactive hydrothermal mounds [Three mounds area (B)], actively venting low-temperature mound [Shimmering mound (A) and Mir zone (D)] and an area of sediment accumulation [Central area (C)] (Rona et al., 1993) (see Figure 1)."

Jan 1, 2017

By R. C. Newell

The primary objective of this study was to establish the fate and distribution of material rejected during marine aggregate dredging, and the extent to which this is associated with spatial changes in biological community composition. Two actively dredged sites in the southern North Sea (Licence Areas 430 and 106) were selected in order to provide a comparison of impacts between sites subjected to different levels of dredging intensity and of contrasting environmental conditions. Dispersal of material rejected during the dredging process was monitored by means of acoustic doppler current profiling techniques (ADCP). Composition of the substratum and benthic invertebrate assemblages were investigated by the analysis of seabed grab samples. It was found that dredging in both areas had an impact on seabed bathymetry in the form of dredge furrows and also led to a reduction of the coarse gravel-sized components of the worked area. Sand sized particles were shown to increase in the surface deposits of both dredged areas. This is likely to reflect both the removal of coarse particles as cargo and the settlement of finer particles rejected during overboard screening. Dispersion and settlement profiles of material rejected by dredging vessels suggested that the majority of the suspended sediment load resulting from overboard screening settles to the seabed within 500 m. Some evidence of suspended sediment loads above background levels were noted at distances of up to 2 km from the working vessel. Analysis of the particle size composition of the deposits, along the axis of transport of material from the dredged sites, suggested that the impact on the sediment composition outside the boundaries of the dredged sites is dependent on the strength and direction of net sediment flux at the seabed. Benthic invertebrate communities within the dredged zones of both areas were found to differ significantly from communities in nearby undredged deposits. A major suppression of species richness and abundance was noted in the dredged sectors of both sites when compared to control locations. A ?footprint? of potential impact on the benthic fauna was noted in samples taken along the axis of sediment transport at distances of up to 1750m outside the boundaries of Area 430. In contrast, impacts on benthic community structure at Area 106 appeared to be confined to the immediate vicinity of the dredged zone itself. This apparent difference in impacts, beyond the boundaries of the dredged sectors between the two study sites, was thought to be a reflection of the smaller quantities of material rejected at Area 106 and the weak seabed sediment flux which is characteristic of this area. These findings, along with those of numerous dredging impacts studies, were then used to make generalised predictions of macrobenthic community recovery following marine aggregate extraction in a variety of seabed habitats.

Jan 1, 2004

By Tetsuo Yamazaki

Seafloor massive sulfides (SMS) in the western Pacific have received much attention as resources for gold, silver, copper, zinc, and lead (Lenoble, 2000). Since the end of the 1980s, SMS have been found in the back-arc basin and on oceanic island-arc areas. The typical representatives found are in the Okinawa Trough and on the Izu-Ogasawara Arc near Japan (Halbach et al., 1989; Iizasa et al., 1999), in the Lau Basin and the North Fiji Basin near Fiji (Fouquet et al., 1991; Bendel et al., 1993), and in the East Manus Basin near Papua New Guinea (PNG) (Kia and Lasark, 1999). The higher gold, silver, and copper contents in one of the areas increased the chance for profitable mining operation, which was considered by a private company (Malnic, 2001). The company gathered investment money and announced to start the commercial mining from 2010 (www.nautilusminerals.com). On the basis of geological information of the Sunrise Deposit of the Myojin Knoll on the Izu-Ogasawara Arc (Iizasa et al., 1999) and geotechnical characteristics of SMS (Yamazaki and Park, 2003), some preliminary economic validation analyses of the SMS mining in small production scale were reported by one of the authors (Yamazaki et al., 2003; Yamazaki and Park, 2005; Yamazaki, 2007). The results showed high profitability of the SMS mining.

Jan 1, 2011

By Roger Amato

The 1982 United Nations Convention on the Low of the Sea includes provisions under Article 76 for extending a coastal State's jurisdiction beyond the 200-nautical-mile (nm) Exclusive Economic Zone (EEZ) and for establishing the seaward limits of sovereign rights over natural resources. Article 76 prescribes a set of methodologies for determining these outer limits based on physiography and sediment thickness. The methodologies were applied to each of the five continental* margin areas of the United States - Atlantic, Pacific, Gulf of Mexico, Alaska, and Pacific Islands-using existing digital hydrographic and geologic data. Figures 1 and 2 show the results of applying the methodologies to the Atlantic, Pacific, Alaskan, and Gulf of Mexico continental shelves. Figure 1 depicts the preliminary limits of each of the Article 76 determinations for the Atlantic and Gulf of Mexico continental shelves. The Atlantic limits were described by Carpenter, Thormahlen, and Amato (1995) at the 26th Underwater Mining Institute.1 The limits for the Alaskan continental shelves are shown in Figure 2. Additional areas beyond the 200 nm EEZ are highlighted. These include a small area north of the U.S. - Canada boundary, containing 7,000 km2, a large area north of Point barrow (395,000 km2), and a third area north of the Aleutian Islands (178,000 km2). The shelf between the first two areas appears to have sediments thick enough to qualify for the 1 percent method (Irish Formula); however, year-round ice cover has prevented acquisition of seismic or drill data. The entire northern Alaska shelf is prospective for petroleum The Gulf of Mexico (Figure 1) has two small areas beyond the EEZ known as "doughnut holes." One is south of Louisiana and includes part of the Sigsbee Escarpment, an area believed to have potential for oil and gas. Oil was found on Sigsbee Knoll in cores from Deep Sea Drilling Project's Leg 1 cruise in 1968. The Sigsbee areas contains about 6,000 km2. The second area is south of the Florida panhandle and contains about 12,000 km2.

Jan 1, 1996

By Sofia Martins, Anna Lichtschlag, Sven Petersen, Fernando Barriga, Bramley Murton, Adeline Dutrieux

"Sediments in the vicinity of the hydrothermal seafloor massive sulphide (SMS) mounds are characterized by high concentration of metallic particles. They result from a long process of weathering of the primary mineral deposits and have been accumulated in depressions by mass wasting and hydrothermal plume fall-out. We present here the first results obtained on pore waters analyses of such sediments in distinct geological seafloor environments (in low-temperature hydrothermally active zones, on extinct hydrothermal mounds and in a remote depositional channel). Vertical concentration profiles suggest that the pore fluid composition is affected more by seawater circulation compared with hydrothermal fluid flow in all environments. The composition of pore fluids is affected by diagenesis and redox processes in the distal depositional channel where Mn2+ is released at depth with Cu2+.IntroductionMarine hydrothermal fields, hosting seafloor massive sulphides, are potential resources for future deep-sea mining and might become economic reserves for the industries. They are widespread at mid-oceanic ridges, arcs and back-arc spreading centers (Hannington et al., 2011; German et al., 2016). Sediments in the vicinity of these fields can contain unusually high concentration of Fe, Mn, Zn and Cu among other metal elements (Shearme et al., 1983). These hydrothermal, or metalliferous, sediments result from a combination of processes such as collapsing and weathering of chimney material, filling of the channels by turbidite-like mass wasting, in situ authigenic mineralization and hydrothermal plume fall-out (Goulding et al., 1998; German et al., 1990). The sediments contain important indicators reflecting the development of the hydrothermal systems. Because of their widespread distribution and metal content, they themselves can be considered potential mineral resources. Circulation of seawater through these deposits, however, often modifies the sediment composition by oxidizing the sulphides into oxyhydroxides and clays causing mobilization of the metals. To address the importance of alteration and diagenesis of these hydrothermal sediments, including the result of seawater circulation, we investigated the post-depositional processes occurring in the hydrothermal sediments at the TAG Hydrothermal Field (Mid-Atlantic Ridge, 26°N), focusing on the mobility of metallic cations in a number of different seafloor environments."

Jan 1, 2017

By K. Vanstaen, K. M. Cooper, S. Ware, S. L. Boyd

Remediation and restoration of offshore marine habitats is a relatively new concept with attempts in European regions largely being instigated by requirements of various strategic directives including Article 2 of the Habitats Directive (1992), the EC Water Framework Directive (2000, Article 2 of the OSPAR Convention (1992) and the developing European Marine Strategy Directive. A field experiment to establish the practicality of various options for rehabilitating the seabed on the cessation of dredging has been successfully set-up. The purpose of this experiment is to investigate the practicality and effectiveness of gravel seeding as a potential restorative method which could be applied at marine aggregate extraction sites following cessation of dredging. Zone 2, within Area 408 (offshore Humber) was chosen as the experimental site as there is some evidence for persistence of sand which may have resulted from screening operations at this site.

Aug 24, 2006

By K. Vanstaen, K. M. Cooper, S. Ware, S. L. Boyd

Remediation and restoration of offshore marine habitats is a relatively new concept with attempts in European regions largely being instigated by requirements of various strategic directives including Article 2 of the Habitats Directive (1992), the EC Water Framework Directive (2000, Article 2 of the OSPAR Convention (1992) and the developing European Marine Strategy Directive. A field experiment to establish the practicality of various options for rehabilitating the seabed on the cessation of dredging has been successfully set up. The purpose of this experiment is to investigate the practicality and effectiveness of gravel seeding as a potential restorative method that can be applied at marine aggregate extraction sites following cessation of dredging. Zone 2, within Area 408 (offshore Humber) was chosen as the experimental site as there is some evidence for persistence of sand which may have resulted from screening operations at this site.

By Natalia Konstantinova, Kira Mizell, James R. Hein, Georgy Cherkashov

"Ferromanganese crusts and nodules from the Amerasian basin of the Arctic Ocean are characterized by a unique composition compared to crusts formed elsewhere in the global ocean (Konstantinova et al., 2017; Hein et al., 2017). One of the most significant differences from global ocean crusts is the high detrital mineral content; mass balance calculations show that it may be as high as 35% in some samples (Hein et al., 2017).These Arctic Ocean Fe-Mn crusts also typically have three distinct megascopic layers, except for thin crusts; less commonly, four layers are noted for thick crusts. The age of initiation of Fe-Mn crust growth in the Amerasia Basin varies from 14.8 Myr to 0.7 Myr ago based on the Manheim and Lane-Bostwick (1988) Co chronometer, Be isotopes, and Th excess methods (Dausmann et al., 2015; Konstantinova et al., 2017; Hein et al., 2017).Samples and MethodsFourteen Fe-Mn crust samples recovered on Russian and U.S. research cruises were chosen for analyses based on their morphology, composition, water depth, genetic type, and location in Amerasia Basin. Seven samples from four distant dredge sites along Mendeleev Ridge and seven samples from four locations on the Chukchi Borderland are included (Fig. 1). Dredge site water depths vary from 3850 to 2100 m with the deepest samples from the Chukchi Borderland. Many of the selected samples were described in previous publications (Konstantinova et al., 2017; Hein et al., 2017)."

Jan 1, 2017

By Se-Won Chang

This is a part of the joint KIGAM-GNS-NIWA 3-year study of ferromanganese nodules on the Campbell Drift, east of Campbell Plateau to determine age distribution, growth rates and geochemical evolution in relation to geographic setting. During the research voyage SAA3 by R/V Tangaroa (TAN 9909) in July-August 1999, seafloor sampling and camera towing were conducted along the two transects across the known flow path of the Deep Western Boundary Current (DWBC) perpendicular to the lowermost margin of the Campbell Plateau and Bollons Seamount. The four major nodule facies, SHH (slope hydrogenetic nodules with high density), AHH (abyssal hydrogenetic nodules with high density), ADH (abyssal diagenetic nodules with high density), and ADL (abyssal diagenetic nodules with low density) were identified. Two additional minor nodule facies, SIB (slope irregular nodules with ice-rafted boulders) and SHB (slope hydrogenetic nodules with boulders and crust), of localized distributions are also identified.

Jan 1, 2003

By Seung-Kyu Son

This study was investigated about physico-chemical parameter such as water temperature, salinity, inorganic nutrients and total organic carbon (TOC). CTD (Model: Sea-Bird 911 Plus) castings were carried out on two transects in the northeast equatorial Pacific Ocean. As a part of the Korea Deep-sea Environment Study (KODES), inorganic nutrients and TOC were determined at 41 stations located from 131° to 136°W along 10.5°N and from 17° to 5°N along 131.5°W (Fig. 1). We particularly chose KODES Long-term Monitoring Station (St. KOMO) to observe for the annually environmental baseline study in the contract area. [ ]

Jan 1, 2005

By Gary J. Massoth

Wherever hydrothermal fluids vent from the seafloor they will buoyantly rise (up to 100?s of meters) while mixing with seawater before attaining density equilibrium and dispersing laterally as neutrally buoyant plumes commonly 50 to several 100?s of meters in thickness and with order-of-magnitude or greater breadth. Although these plumes are typically >10,000-fold dilutions of vent fluids they can be reliably detected using sophisticated physical sensing and chemical techniques. Hence, hydrothermal plumes are spatially large targets compared to the actual sites of seafloor fluid discharge and resulting mineralization. For this reason plume prospecting techniques evolved over the past 20+ years have been widely used to systematically explore over 10% of the 60,000-km-long system of mid-ocean ridge (MOR) spreading centers for hydrothermal activity. While plume detection and gradient mapping can be used to home in on venting sites, plume chemical signatures provide additional insight regarding the nature of the fluids being discharged on the seafloor. We have applied the systematic plume prospecting techniques developed on MORs to the volcanic frontal arc setting as part of the NZAPLUME (New Zealand American PLUme Mapping Expedition) surveys. NZAPLUME I in March 1999 marked the first systematic reconnaissance of any intra-oceanic arc for submarine hydrothermal activity. Seven of thirteen previously mapped volcanoes that comprise a 260-km-long section of the southern Kermadec arc northeast of New Zealand were confirmed to be hydrothermally active. On average, one hydrothermally active volcano was found along each 35 km of arc front, a rate comparable to slow- and intermediate-rate spreading MORs. During NZAPLUME II in May 2002, thirteen previously unknown volcanoes and 8 satellite cones were first swath mapped for bathymetric detail and then surveyed using plume prospecting techniques. Three active venting sites were discovered along this 580 km-long arc section, bringing the total to 10, or 39% of 26 volcanoes surveyed overall, still an appreciable frequency rate for venting sites compared to MORs. While only chemical results for NZAPLUME I are available, the arc plumes characterized so far are chemically diverse and rich compared to MOR plumes. This diversity and enrichment was most evident as ultra-high concentrations of CO2, sulfur gases (St = SO2 + H2S), and Fe within plumes over several volcanoes. We suggest the fluids discharging from the seafloor at these sites are volcanic fluids, i.e., hybrid fluids comprised of MOR-like hydrothermal fluids evolved from seawater-rock reaction and fluids exsolved from magma as acid volatiles and liquid brines.

Jan 1, 2002

By Chuanshun Li, Haitao Zhang, Xuefa Shi, Quanshu Yan, Zhiwei Zhu

In Expeditions 22 and 26 of China Ocean Survey (COS), Chinese and Russian scientists have Carried out a lot of work to search for hydrothermal sulfide in Southern Mid-Atlantic ridge (SMAR) 19°S, but come back empty-handed at last. The sulfide formation is closely related with the water-rock reactions which are controlled by the heat source. Melt inclusions are considered to have a unique compositions in melt to reflect the deep magma processes. Fortunately, we have found a large number of plagioclase hosted melt inclusions in SMAR19°S MORB. We have done experiments by re-homogenization and re-crystallization of these melt inclusions. During the re-homogenization experiments, the forming and melting processes of the olivine crystal inside the melt inclusions indicate that the homogeneous temperature of melt inclusions is 1190-1200??. During the recrystallization experiments, the different mineral phase assemblages show H2O inside the melt inclusions has hardly ever been loss, in addition Cr element and H2O molecule in SMAR19°S magma are heterogeneity at the time of melt inclusions trapping, and then the re-crystallization experiments provide a method to prove the microheterogeneity of basaltic magma system. Combining with the bulk rock data, this study shows that the melt inclusions are formed at a low-temperature and high-pressure condition. Eventually, this paper speculates that a low temperature heat source generated by a lower mantle potential temperature or/and a thick lithosphere indicated by the melt inclusions that not experienced the H2O loss process are beneath the SMAR19°S. The low temperature heat source transmits its heat to lithosphere through the cooling thermal boundary layer (CTBL), and the thick lithosphere can sufficiently absorb and consume the heat. Under the interaction between the heat source and lithosphere, the residue heat at the infiltration depth of sea water might have been no ability to satisfy the water-rock reactions temperature, therefore, the water-rock reaction should hardly ever appear, so the theoretical reaction zone would not exist beneath the SMAR19°S. Eventually, the interaction between thick lithosphere and the low-temperature heat source should be the dominant factor that makes SMAR19°S area have no condition to form the seafloor sulfide. However, this paper is based on melt inclusions only, in fact, melt inclusions are potential to have melt compositions produced by mineral dissolution, reaction and assimilation, and the volumes of melt inclusions are exceedingly small compared to the overall size of the magmatic systems, therefore, the extrapolation across many orders of magnitude is implicit when applying petrologic information obtained from inclusions to entire magmatic systems. Therefore, there should have other more research to verify the reliability of this conclusion.

Jan 1, 2017

By T. Schoening

The exploration of the seafloor regarding the abundances of poly-metallic nodules has received growing attention recently. Image-based exploration using cameraequipped deep-sea observation systems has been introduced successfully to increase spatial resolution in the exploration process but the evaluation and interpretation of the huge amount of image data creates a serious bottleneck. In this paper we present a new software solution to the problem of automatic detection and segmentation of poly-metallic nodules in underwater images, which is not only accurate but so fast that real time image analysis is definitely in reach. Thus, an application on an AUV (Autonomous Underwater Vehicle) seems possible in the near future.

Sep 14, 2011

By Henk van Muijen, Jan Willem de Wit

1.1 Profile IHC Holland Merwede IHC Holland Merwede is world market leader in the construction of specialist dredging equipment and large-size custom-built offshore vessels. The clients of IHC Holland Merwede include major dredging companies, oil and gas exploration groups, offshore contractors and government authorities. IHC Holland Merwede is focused on the continuous development and innovation of technology to ensure maximum performance and efficiency of its designs and constructions supplied to the dredging and offshore industries. IHC Holland Merwede has a staff of approximately 2,000 at its locations in Hardinxveld- Giessendam, Kinderdijk, Krimpen aan den IJssel, Sliedrecht, Delfgauw, Goes, Hendrik Ido Ambacht and Heusden. Besides worldwide representations, IHC Holland Merwede has branches in China, Houston (USA), India, the Middle East and Singapore. 1.2 Mission IHC Holland Merwede’s mission is to optimize value by anticipating and satisfying its client’s requirements, with efficient advanced technology solutions. The group’s aim is to be consistently at the forefront of technology development, in the business sectors in which it operates.

By Tim J. Boyd

Gregg Marine, Inc. (headquartered in Signal Hill, California) has recently introduced an innovative seafloor drill system for offshore geotechnical site investigation and seafloor mineral exploration. The system is capable of working in water depths of up to 3,000 meters and is rated to drill to a depth of approximately 150 meters below mudline. The remote operated system integrates established drilling technology with proven Schilling telemetry and controls. The flexible nature of the patented wireline drilling technology enables the use of standard sampling systems (up to PQ-size core and 3? thin-walled tubes) as well as downhole testing systems (including CPT testing, vane shear testing, downhole sensors and borehole geophysical tools). The modular nature of the seabed drill system and the accompanying launch and recovery system (LARS) enables the use of local vessels of opportunity for projects resulting in reduced project costs and improved mobilization responsiveness times. Keywords: seafloor, seabed, geotechnical, drill, drilling, core, coring, sampling, CPT, cone penetration testing, borehole, logging, survey, exploration, ROV, remote sensing

Jan 1, 2011

By I. Yu. Melekestseva

The Semenov hydrothermal sulfide cluster (13º31´N), consisted of five fields (Semenov-1, -2, -3, -4, and -5), was discovered in 2007 in the 30th cruise of R/V Professor Logatchev [Beltenev et al., 2007; 2009]. The hydrothermal fields are located on a seamount composed of ultramafic and mafic rocks, gabbro, plagiogranite, and their altered rocks. The Semenov cluster is considered to be the largest sulfide accumulation in the Ocean with massive sulfide (MS) resources of about 40 million tons [Beltenev et al., 2009]. MS of the Semenov-1, -3, -4, and -5 hydrothermal fields are mostly characterized by marcasite-pyrite composition whereas rich copper-zinc MS with high Cu and Zn contents (11.37?19.33 and 5.89?18.32%, respectively) and anomalous Au and Ag grades (22?188 ?127?1787 ppm, respectively) were dredged only at the Semenov-2 hydrothermal field associated with basalts (13°31.13´N, 44°59.03´W; 2360?2580 m of depths) [Ivanov et al., 2008].

Jan 1, 2010

By Jeremy Spearman, Alan Cooper, Mark Lee, Jon Taylor, Michael Turnbull, Neil Crossouard, Bramley Murton

"SUMMARYSeamounts are underwater mountains caused by volcanic activity. They are of great oceanographic interest because of their local and basin-scale influence over ocean systems, their often unique ecosystems, and because they are associated with the formation of ferromanganese (Fe-Mn) crusts. These crusts are of particular interest to scientists because they are rich in some of the rare elements increasingly required for development of renewable technologies. When the possibility of mining such seamounts is considered, an inter-disciplinary study of seamount hydrodynamics, crust formation and ecosystem sensitivity is required. MarineE-tech is one such multi-disciplined project that has been commissioned to address these different aspects in order to improve understanding of the viability and desirability of mining Fe-Mn crusts. This paper describes a key part of this study, namely the development of a model, informed by hydrographic observations, of the currents around one such seamount and the in situ validation of a sediment disturbance plume model as a pre-cursor to assessment of the potential effects of mining activity.INTRODUCTIONFerromanganese crusts are thought to form by precipitation of iron and manganese oxides from oxygen depleted mid-water known as the oxygen minimum zone (OMZ). Oxidation rich waters, typically at depths of about 800-2200 m (Hein et al, 2000). This range of depths coincides with the flanks and summits of many seamounts. The ferromanganese crusts found on seamounts have been found to have high concentrations of rare elements, like Tellurium, that are considered critical to low-carbon energy production. Seamounts are complex environments: in terms of the local hydrodynamics that tend to trap water over the seamount due to the Taylor Cap effect (e.g. Chapman and Haidvogel, 1992) and which can enhance the productivity of seamount waters through upwelling (Lavelle and Mohn, 2010), in terms of the microbiological activity that leads to the precipitation of the Fe-Mn crusts, and also in terms of the often unique ecosystems that are the product of the “island” nature of seamounts and the upwelling of nutrients. The understanding of this complexity is a necessary journey towards the realization of viable, yet environmentally responsible, mining schemes. The formation of crusts will be influenced by the local (and larger-scale) hydrodynamics. The exploration of promising crust sites could be made much more efficient by understanding where the most prospective deposits are likely to occur. Knowing how to remove these crusts without impacting significantly on the local environment will be a pre-requisite for such mining to be acceptable to the public and funders alike."

Jan 1, 2017

By Fernando J. A. S. Barriga

"Recent concerns over the availability of many mineral raw materials, and newly available technological developments, produced renewed interest in deep-sea mining. However, environmental concerns, with variable degrees of justification, are raising opposition to the concept. The forecast for the behavior of consumption versus availability of many raw materials, nearly all critical metals, arguably show that consumption will grow much faster than resource discovery onshore. Finding new sources of raw materials seems inescapable. The deep seafloor stands out as the only likely candidate.Sea Floor Mining and the EcosystemMarine mining has already started, decades ago, for diamonds, currently up to depths near 400m. Although the industry recognizes there is a footprint, it considers the footprint quite minor, because the area mined is small: in Namibia, where offshore diamond mining is now 70% of the country’s total, only 3% of the concession of 3,700 sq miles (9600km2) have been mined. As plans to mine deep-sea massive sulphide deposits and polymetallic nodules progress, the environmental concerns grow. Some of these concerns are as follows:?The deep-sea ecosystems are composed of long-lived species, with low rates of reproduction. The environment may not recover from mining on a human time scale;"

Jan 1, 2017

By Cornel E. J. de Ronde, Alexander Malahoff

Six active Kermadec arc submarine volcanoes, located between 34°S and 36°30'S were mapped and sampled between April and July 2005, using submersibles Pisces V and Pisces IV aboard the mothership R/V Ka'imikai-o-Kanaloa. The purpose was to study the relationship between hydrothermal activity, formation of hydrothermal mineral deposits, structure of the volcanoes, and the biodiversity of life associated with the hydrothermal vents. Of the volcanoes examined, all showed evidence of hydrothermal activity, including metal-rich plumes and helium anomalies. Only two of the volcanoes, namely Brothers and Clark, showed chimneys and surficial polymetallic sulfide deposition. Hydrothermal venting at a water depth of approximately 1,650 meters near the base of the northwest caldera wall of Brothers volcano has produced a field of chimneys, up to seven meters high and discharging black smoker venting. Temperatures up to 300°C were measured from the active vents. Clark volcano has a double cone summit at a water depth of 875 meters. The shallowest cone has a near-summit hydrothermal vent field with five-meter tall venting chimneys with smaller structures around the periphery. Water temperatures of 200°C were recorded for these chimneys.

By J. R. Hein

East Diamante is a submarine volcano in the southern Mariana arc that is a complex caldera about 10 km x 5 km (elongated ENE-WSW), and breached on its northern and southwestern sectors. A large field of barite-sulfide mounds was discovered in June 2009 and revisited in July 2010 aboard the R.V. Natsushima using the Hyper-dolphin ROV. The mound field occurs on the NE flank of a cluster of resurgent domes inside the caldera. The mound field extends for more than 100 m long and is about 30 m wide, and is aligned along a NE-SW rift valley. A sample of dacite yielded a 40Ar/39Ar age of 20,000±400 years. Individual mounds are typically 1-3 m tall and 0.5-2 m wide, with lengths from about 3 to more than 5 m. The mounds are composed of barite-dominant layers interbedded with Zn-sulfide-rich barite layers. Rare inactive spires and chimneys cap some mounds. Fe and Mn oxides are currently forming small (<1 m diameter, ~0.5 m tall) subsidiary mounds on the top of some of the sulfate/sulfide mounds and drape the flanks of others. Both diffuse- and focused-flow fluids emanate from the subsidiary oxide mounds. Ages of the basal sulfate/sulfide mounds cluster around 4,000 years old based on 226Ba/Ba, whereas the oxides are less than 5 years old based on 228Th/228Ra. Most mound and chimney samples are dominated by barite and amorphous silica; sulfides occur in variable amounts that in decreasing order of abundance include sphalerite, galena, pyrite, and chalcopyrite. Anglesite, cerrusite, and a Pb phosphate occur as late-stage interstitial phases. Some mound samples have fragmental textures; layered clasts composed of chalcopyrite and pyrite may have been derived from collapsed chimneys. Despite the abundance of barite, samples contain high concentrations of Zn (to 23 Wt.%), Pb (to 13 wt.%), Ag (to 500 ppm), and Au (to 15 ppm). Copper is enriched in a few mounds samples, up to 3 wt.%, but is typically <1 wt.%. Other significant metal enrichments include Sb (to 1320 ppm), Cd (to 1180 ppm), and Hg (to 55 ppm).

Jan 1, 2011