Search Documents

By Alfred H. Brand

New York City contains extensive deep deposits of glacial lake varved silt and clay, often overlain by organic soil. An 18 story building was proposed for Manhattan's upper East Side in one such area where bedrock is approximately 200 ft deep. Various pile and caisson alternatives were considered extending through the glacial lake soil to rock, but all proved beyond the project budget. Laboratory testing showed that the glacial lake deposits were preconsolidated. A test pile program using auger cast piles bearing in the glacial lake deposits proved that such piles could safely carry a load of 60 tons per unit. The auger cast pile scheme was estimated to be more economical than a deep pile alternative. A further benefit was that the vibration-free pile installation procedure posed less risk to adjacent structures which had been founded at shallow depth in fill above organic deposits and were stressed and cracked due to prior settlement. The project was designed with the anticipation that the glacial soils beneath the tips of the piles would produce a building settlement of 1 to 2 inches. The building was constructed in 2001 and 2002. It has been completed and is now occupied. Settlement data show that the building is performing as predicted. The auger cast pile scheme founded in a compressible stratum has proven to be successful and is a very unusual foundation alternative.

Jan 1, 2003

By P. M. Wiltcher

The construction of a deep structural slurry wall in a restricted city centre location is always a challenging prospect. However, when the city is London and the site is bounded on two sides by high level canals and a main traffic highway on the third, the challenges are greater than usual. The paper discusses the design considerations required by the principal contractor to accommodate a single high level lateral support, value-engineered, bottom-up construction technique and the impact this had on the design detailing and construction of the slurry wall panels. This paper discusses the logistical challenges successfully overcome during the construction of 65,000sq ft of 40inch thick, 80ft deep structural slurry wall in the City of London. The paper reviews the benefits gained from using the state-of-the-art hydraulic grab and rotator system. Technological advances in computer instrumentation and real time monitoring were utilised to assist the grab operators in consistently delivering deviational control during excavation better than 1:200. With working space always at a premium on construction sites, the need for high quality, pre-fabricated reinforcement cages has never been greater. This paper reviews the argument for off-site fabrication of reinforcement members.

Jan 1, 2006

By Maurice Bottiau

It is a quite challenging objective to aim at covering in one paper the most recent evolution in piling and deep foundations technologies. This report has to be understood within the limits of the session 2b. It will therefore concentrate on the technological evolution of deep foundation techniques, addressing design issues only when directly related to execution aspects. For the same reason, it will not address the related codes, as a separate session of this conference is specifically dedicated to this topic. Monitoring and deep excavations being covered in other sessions, they will only be addressed when clearly relevant. We will try to show, from a practical viewpoint what are the main changes and the most exciting or critical issues over the last years, as they appear from the topics addressed in the literature or in the papers published in this session of the conference. As the paper mostly intends to explain trends and critical topics, it cannot be exhaustive, neither can it give the full description of the case studies. The author invites the reader to read the full papers, for a more complete description. We have divided our report in three main topics: Piling, soil improvement and treatment and retaining walls. Anchors and tie-backs will not be treated, neither tunneling.

Jan 1, 2006

By John F. MacDonald

From 19BS thru the present, Guy F. Atkinson Construction Company has been involved in several transportation construction projects in the Seattle area. Two of these contracts, the Mt. Baker Ridge Tunnel, and The Seattle Bus Tunnel, had unique foundation features. MT. BAKER RIDGE TUNNEL ACCESS PITS The Mt. Baker Ridge Tunnel is part of the general upgrading of the I-90 freeway between I-405 and I-5 (see Fig. 1). It is located on the western shore of Lake Washington and consists of a 1300 foot long large diameter tunnel thru Mt. Baker Ridge. The ridge consists of over consolidated silts and clays overlain by a loose to medium dense silty fine sand. The water table is perched in this upper layer of material. The clays of Seattle have a history of being very sensitive to excavation. The hills are marginally stable and numerous landslides have occurred recently in the area of the tunnel. [ ]

Jan 1, 1990

By Alan J. Lutenegger

Some years ago, a method was developed to incorporate a grout column around square-shaft helical screw-piles and anchors to increase shaft buckling resistance under compression loading. An additional benefit of this grouted shaft is to increase the load capacity in both compression and tension, depending on the geometry of the lead helical section and the soil conditions. Because of the unique construction procedure, the contribution of the shaft to the total capacity has largely been unknown. The behavior of grouted shaft helical anchors in clay was investigated by performing full-scale axial uplift (tension) load tests on a series of anchors installed at the University of Massachusetts Geotechnical Test Site. In order to isolate the contribution of the grouted shaft to the total load capacity, anchors were installed with a wooden dowel connection between the lead helical section and extension sections on three of the four anchors so that only the shaft resistance would be measured during the load tests. The grouted shafts ranged in length from 10 to 30 ft (3 to 9 m). Initial tests were performed approximately 5½ months after installation. Nearly four years after the initial tests were performed, the tests were repeated to evaluate any significant change in capacity with time and/or repeat testing (preshearing). The soil conditions at the site are presented along with the load-displacement curves for both the initial and repeat teats and a discussion of the analysis of the results. Repeat load tests showed an increase in capacity from the initial testing, however the percent increase was not the same for all depths. The results demonstrate that considerable shaft resistance can be developed in clays from the grouted shafts as might be expected. Depending on the L/D ratio of the shaft and the contribution of the lead helical section, at working loads the shaft capacity can dominate the behavior.

Jan 1, 2011

By Bert R. Oastler

BERT R. OASTLER: Born Atlanta, Georgia, October 19, 1933; B.S. Civil Engineering, Duke University, 1956; Doctor of Laws, Emory University, 1966; Bryan Honor Society; Associate Editor, Journal of Public Law. Partner in charge of litigation for Smith, Currie & Hancock Including federal and state courts, administrative boards, arbitration and negotiation. American Bar Association; American Trial Lawyers Association; Georgia Trial Lawyers Association. Practiced structural steel design at Newport News Shipbuilding & Drydock Company and building construction as an officer in the United States Air Force. Engaged in the building construction business in Atlanta, Georgia as estimator and project manager for five years. Lectured on construction litigation, arbitration and government contracts procurement law for Federal Publications, Inc., Associated General Contractors and other private entities on a nationwide basis. Served as guest lecturer on Government Contracts at Emory University and Georgia Institute of Technology, Atlanta, Georgia. Served as arbitrator in cases for the American Arbitration Association.

Jan 1, 1988

By Michael H. Wysockey

The load test program for the pile foundation at Soldier Field included static and dynamic load tests at four locations around the site. The dynamic tests were run with no knowledge of the static results, and comparison between the two is very good. It was necessary to use a special testing hammer (not the production hammer) to demonstrate capacity with dynamic testing. Over 90% of the piles were HP14x89 with a design load of 230 tons (18 ksi). The load tests showed a capacity in excess of 590 tons for all tests where sufficient set up time was allowed. The remainder of the piles were mostly HP 12x53 with a design load of 100 tons (13 ksi). The measured capacity of these piles was typically about 250 tons. One experimental HP12×74 pile with a nominal yield of 65 ksi held 730 tons (67 ksi) before failing.

Jan 1, 2002

By Li Keqiang

This paper discusses the pile foundation of tall buildings in Shenzhen region. For 156 constructed tall buildings exceeding 18 storeys, about 86. 5 per cent of the sum. The two main types of foundation used are the semi?machine?bored/slurry drilled cast?in?situ pile and the excavation pile (hand ?dug caisson). The engineering geologiical condition in Shenzhen was analysed. In general, the bed rock level is not too deep. It belongs to hard rock, but the geologic structure is more complex and the tectonic fissures is plenty. According to experiences of the researches, tests, designs and constructions of pile foundation, we present the basic design principle of pile foundations for tall buildings as follows; (1) pile strength control to select the pile type and to choice the cross sectional dimen­sions, must be in compliance with the strength of the pile. (2) bearing stratum strongly weathered, moderartely weathered and slightly weathered rock may be used as the bearing stratum. (3) bearing pile bored /drilled cast-in-situ pile designed as an end bearing pile. (4) friction pile precast concrete pile, prestressed concrete tubular pile and driven cast-in-situ pile designe as a friction pile. In case, pile design is in compliance with these principles, it may be safe, economical and reasonable.

Jan 1, 1991

By R. Stenne

This paper presents the trends in deep foundations in Europe, both in terms of design and construction. Eurocode 7 which is a design code for geotechnical engineering will be introduced in the European Union member countries, and will oblige geotechnical engineers to abandon traditional methods based on a global factor and adopt a new approach based on partial factors of safety. Execution codes (for construction of foundations and other geotechnical processes) are currently being introduced without problems. Ever more demanding environmental constraints push foundation contractors to adapt old techniques and develop new ones to comply with new regulations.

Jan 1, 2000

By Paul J. Axtell

This case history describes the foundation design and construction for the New Mississippi River Bridge, presently under construction in St. Louis, Missouri. The 1,500 ft (457.2 m) main span of the cable-stayed bridge is supported by two delta tower pylons in the river, with anchor piers on each bank. The final foundation design was completed as a part of an Alternate Technical Concept (ATC) proposal by the winning construction team, and utilized drilled shafts up to 11.5-ft (3.5-m) diameter that were socketed into very hard limestone. As part of the ATC foundation design, a full-scale, bi-directional static load test was performed to verify the design and allow use of higher resistance values. This paper presents the results of the site exploration, construction of the load test shaft, details of the load testing, and a comparison of the test results with various design parameters.

Jan 1, 2011

By Samuel J. Kosa

The Monotube is a uniformly tapered high-strength steel shell pile manufactured for friction pile applications. The Monotube pile was developed in the early 1920's in Canton, Ohio. Its first commercial installation was an Ohio railroad trestle in 1926. The Monotube has been manufactured in the same Canton plant since its inception. The Monotube is produced in four diameters, 12, 14, 16 and 18 inches, with U. S. Standard Gage wall thicknesses of 9, 7, 5 and 3. The uniformly tapered Monotube section can be manufactured in one of three rates of taper.

Jan 1, 1993

By Matthias Pulsfort, Markus Herten, Rolf Breitenbücher, Claudia Fierenkothen

"Secant bored pile walls are frequently used as retaining walls in watertight excavations to cut off ground water aquifers and are subsequently exposed to ground water pressure loading in addition to earth pressure loads. To avoid extra loading from ground water pressure in soils with limited permeability, it can be useful to arrange drainage windows within secant bored pile walls by means of single primary piles filled with porous concrete without reinforcement cages, which usually have to be placed within casings in submerged conditions. This concrete may serve as a horizontal arch between the reinforced secondary piles, but it must however enable vertical draining between load carrying construction beams and the bottom of the excavated pit. In the present submission, the results of several material tests with different mix designs of porous concrete with certain admixtures are presented together with first and important experiences with a wellsuited placement technique for porous concrete casings in small- and large-scale laboratory tests. It can be shown that the usual placement technique of employing a tremie pipe is not suited for this type of unsaturated concrete. Instead, pouring with a particular kind of cone and an open conductor pipe has proven successful.Additionally, special testing methods are currently developed for judging the suitability of the desired concrete mix design in preparation for an upcoming real-scale experimental pile installation in Germany.1. INTRODUCTIONRetaining walls are often built as secant bored pile walls in order to cut off aquifers saturated with groundwater against deep building pits. In soil types with relatively low permeability, however, seepage flow may be permitted, because the quantity of groundwater to be pumped is limited, and the range of influence due to dewatering is not reaching far. Thus, the hydrostatic water pressure on the retaining wall can be considerably reduced, leading to a more economic design (see Fig. 1).In unsaturated soils, the dewatering effect can be achieved by means of porous pervious concrete with a uniform grainsize distribution of aggregates typically placed in a borehole under dry conditions. With regard to the use of porous concrete to be placed at the ground surface in road pavement applications, experience is sufficiently available as shown, for instance, by Neithalath et el. (2010). However placing the porous concrete in a bored pile using a tremie pipe under submerged conditions is a challenge and a completely new approach, because there is a considerable risk of segregation of the fresh concrete, separating the cement lime paste from the aggregates when in contact with water and leaving only neat gravel on the one hand as well as a tight cemented area at the bottom of the pile on the other hand. If this concrete placement is successful, additional dewatering by means of extra wells behind the retaining wall can be avoided. Of course the seepage flow in the adjacent soil needs to be regarded seriously."

Jan 1, 2017

By Thomas M. Gurtowski

The New Pacific Northwest Baseball Park, now known as Safeco Field, is located directly south of the Kingdome in Seattle, Washington, and will be the new home of the Seattle Mariners baseball team. The location of the ball field is shown on Figure 1, Vicinity Map. The seating capacity is 45,600, and outfield distances are 331 feet in left, 405 feet in center, and 326 feet in right field. The overall dimensions of the stadium are 680 by 800 feet. It is bordered on the east by the Burlington Northern Santa Fe Railroad main line. A unique aspect of this ballpark is the retractable roof with a north-south span length of 660 feet. The roof consists of three separate sections that roll on elevated rails running east-west on the north and south sides of the stadium. The soil conditions consisted of near-surface fill underlain with alluvial and Estuarine deposits to depths of 60 to 80 feet. The bearing soils consisted of very dense, glacially overridden deposits. Groundwater is 4 to 7 feet below the ground surface, and the alluvial deposits are subject to liquefaction during a strong motion earthquake.

Jan 1, 1998

By Mark M. Petersen

As part of the addition of eight new combined cycle generating units at the Florida Power & Light Sanford Plant, 2,129 piles were to be installed. The existing plant elements were supported on driven piles, and the variation in pile lengths during previous work, as well as available subsurface information, indicated a complex stratigraphy. At the request of the owner, the designer/construction manager developed a program to evaluate the use of pressure-grouted displacement piles. A pre-design load test program in areas that represented the apparent extremes in subsurface conditions indicated that the system was feasible; however, the presence of existing features that were to be demolished later precluded the clear delineation of subsurface conditions in advance of construction. A contract was negotiated with the pile installer based on the best estimate of potential pile lengths, with modifications to pile lengths to be set based on additional exploration. A total of 52 cone penetration soundings and five load tests were performed immediately prior to and during pile installation to establish correlations between the CPT data and pile performance. Pile depths were set based on these correlations. Pile installation was completed 6 weeks ahead of schedule and 15 percent under the original budget estimate. This paper documents the evaluation of pressure-grouted displacement piles as an emerging technology, and illustrates the benefits of a close working relationship between the owner, designer, and pile contractor at a site with variable subsurface conditions.

Jan 1, 2002

By Mario Terceros H., Bengt H. Fellenius

"ABSTRACTFour strain-gage instrumented bored piles were constructed in a sedimentary, dense to very dense, fine to medium sand in Santa Cruz, Bolivia. Two of the test piles were the normally used bored pile constructed with bentonite slurry and two piles were Bauer Full Displacement Pile (FDP). One of each pair was equipped with the Expander Body, an inflatable steel cylinder that on pressure-grouting provides an enlarged pile toe. Head-down static loading test were performed on three of the piles and a bidirectional test was performed on the fourth pile, a standard pile with Expander Body and a bidirectional cell placed immediately above the EB. The latter pile was tested in 3 phases. First by activating the cell, second, by a head-down test, and, third, by a repeat bidirectional cell test. The static loading tests proved the shaft resistance of the FDP pile to be about twice that of the standard bored pile and that the Expander Body more than doubled the toe stiffness. The strain-gage records showed that the standard bored piles had multiple bulges and neckings, which affected the evaluation of the axial stiffness and load distribution of the piles. The testing programme was used for a prediction event with 60 persons, ahead of the tests, submitting predictions of the load-movement curves for the test piles and also a capacity appraised from the curves.1. INTRODUCTIONOn April 23 - 26, 2013, the First International Conference and Seminar on Deep Foundations was held in Santa Cruz, Bolivia under the auspices of INCOTEC SRL, the UAGRM University, and the Bolivian Association of Civil Engineers and Chamber of Construction. To coincide with the conference, a research study on construction and static and dynamic testing of four instrumented bored piles was undertaken. To ""add spice"" to the conference, a prediction event was organized on the test programme. This paper presents the soil conditions at the site, the type and construction of the test piles, the outcome of the prediction event, and the results of the static tests.2. SOIL CONDITIONSGeotechnical studies comprising SPT and CPT tests with routine laboratory analysis were performed on recovered soil samples. Three SPT boreholes were put down at three of the locations of Pile TP1, TP2, and TP3, at 5.0 m distance from each other. The SPT procedure consisted of manual hoisting of the weight by three crew members pulling on ropes over a pulley supported by a tripod and letting the weight fall by gravity. The groundwater table lies at 3.5 m depth.Figure 1 shows diagrams of the SPT N-indices and the distribution of water content in the three boreholes. The SPT-indices show the soil density to be compact. The average water content is about 15 %, plus-minus a few percent."

Jan 1, 2014

By Hal W. Hunt

Steel and concrete piles and power-actuated hammers have developed almost entirely within the past 100 years. Prior to that time, piles were mostly timber, driven with a drop hammer or a maul. The Engineering News Formula ? for timber piles driven with a drop hammer at a factor of safety of six ? was promulgated by Wellington in 1888. Steel com­panies supplied fabricated and rolled shapes for piles in the early 1900's. The thin shell and then uncased concrete piles originated about that time. Now leads have become sophisticated to accurately spot a pile at any required batter. Hammers have grown to phenomenal size and vibratories are being accepted at full value.

Jan 1, 1984

By Jesse A. Pfeiffer

CPAR, the Construction Productivity Advancement Research Program, is a new initiative of the Corps of Engineers to enhance U.S. construction industry productivity through the development and application of joint-funded research. CPAR seeks to balance the requirements of both the private sector and the Corps of Engineers construction program, to identify research needs that are common to both parties in a partnership for conducting research, and to achieve practical real-world products which will enhance productivity in the construction industry. Increasing costs of doing business has had a major negative impact on much of the nation's industrial base, and research and development (R&D) is among the areas hardest hit. The Congressional Budget Office estimates that since 1984 inflation adjusted R&D outlays in private U.S. firms have risen at an average annual rate of three percent, or about half the rate of gain of the preceding decade. And, despite a significant increase in foreign competition, the portion of gross national product (GNP) devoted to R&D is lower today than 20 years ago. For the case of the U.S. construction industry, the numbers are even more dramatic.

Jan 1, 1989

By Claudio Olalla

This paper relates to the foundation of a steel structure located at the San Martin de la Vega (Madrid) amusement park. The structure has more than 100 supports with various loading conditions, including important horizontal and uplift forces. Additionally, the settlement tolerances are very strict. A massive gypsum formation with interbedded clay layers and random solution great voids at various levels constitute the soil. The foundation design has been conditioned large enough these difficulties (load conditions and soil problems). The piling machine used was powerful to drill through the soft rock (UCS up to 11Mpa). The integrity of each pile had to be guaranteed by continuous recording of drilling and concrete pouring parameters. In order to fulfil all those conditions, a STARSOL type-piling rig was used. More than 4500 meters of piles were performed. The diameters of the piles were 450 and 550-mm and their depths varies from 6 to 23 meters. All piles were reinforced over their full length.

Jan 1, 2002

By Guo H. Lei

Over the last four decades, barrettes have been ever-increasingly adopted as the foundations for tall buildings and heavy infrastructure projects all over the world. Many findings have been gained from practical applications and theoretical researches. In this article, a collection of literature is reviewed on the installation effects and load-carrying behaviour of barrettes derived from field and laboratory tests and theoretical studies. It covers many aspects, such as the ground deformations and stress changes caused by the installation of barrettes, the shaft resistance mobilisation behaviour, the construction effects on the shaft resistance, and the effects of pile spacing, pile shape and pile group layout on the load-carrying behaviour of barrettes.

Jan 1, 2006

By Dan Brown

Two drilled shaft foundations were subjected to axial load tests in order to measure the influence of drilling fluid on performance. Other than the differing drilling fluids, the shafts were constructed with great care to ensure identical conditions. The results indicate superior performance in both side shear and base resistance of the shaft constructed using a polymer over that of the shaft constructed using bentonite drilling slurry.

Jan 1, 2002