Search Documents

By J. J. O?Neill

Introduction The Beattie mine is the first of its character to be exploited in Quebec. It is primarily a large low-grade gold deposit containing values which a few years ago would not have been considered as ore. Much interest is attached to this development as its success may mean a greatly enlarged scope to gold mining in Canada on deposits which have formerly been considered worthless. Because of its potential importance as a pioneer in low-grade gold mining, the Quebec Bureau of Mines decided to make a careful detailed study of the Beattie in the hope not only of assisting in its development, but of stimulating the search for similar essential geological conditions in other parts of the Province. This paper is a summary of the results obtained during two months on the property in 1932, supplemented by a few trips underground in 1933. The full report will appear in the Annual Report of the Quebec Bureau of Mines for 1932, Part C. Location and Means of Access: The Beattie ore-body is situated two miles west and one half mile north of the centre of Duparquet township, and approximately 22 miles north 28° west of the town of Noranda. Until the fall of 1932, access to the property was from LaSarre, on the Canadian National railway, over a thirty-mile water route with one portage 600 feet long; about 2,000 tons of machinery and supplies were taken in by that route. An automobile road, nine miles long, now connects the property with the Makamik highway, and a narrow-gauge railway, without ballast, gives outlet for concentrates from the mill to the C.N.R. tracks of the Rouyn-Taschereau line, nineteen miles distant.

Jan 1, 1934

By J. Dubinski

This paper describes the key circumstances of the underground coal gasification (UCG) process, which is planned to be carried out in the Polish hard coal mine ?Wieczorek?. The construction and field tests of a UCG pilot plant have key issues that need to be addressed to realize the research project goal: the elaboration of a highly effective technology of fuel and electricity production. The project will conduct several monthly tests of gasification in the pilot geo-reactor, which will be constructed based on the results of laboratory tests. The realization of the process requires numerous appropriately prepared actions adjusted to natural conditions in the hard coal deposit. Based on scientific principles, it is necessary to elaborate the procedures related to the location of the UCG installation (including its legal and safety aspects), and to perform a technical risk analysis. In addition, it is necessary to determine the required mining, geological, technical, economic and organizational circumstances, while at the same time considering the real but constantly changing process conditions.

Aug 1, 2013

By Chun-Sheng Liao, Chun-Hua Yan, Sheng Wu, Fu-Xiang Cheng

"INTRODUCTIONChina is providing more than 90% of the rare earth products consumed in the whole world. Acidic extractants are commonly used in the extraction separation of rare earths. Saponification of the acidic extractants by basic substances is usually necessary for the purpose of increasing and stabilizing their extraction capacity, and meanwhile inorganic acids are required for both scrubbing and stripping. Thus acids and bases are the main consumed chemicals, and the resulting salts are the main pollutants generated by rare earth separation processes. Currently, due to increasing environmental concerns in China, rare earth solvent extraction separation techniques are being developed to reduce both consumption and emission of chemicals, which is driving the developments on both theories and processes for solvent extraction separations.In the 1970s Prof. Xu et al. developed the Theory of Countercurrent Extraction (Xu, Li, & Yian, 1985). In recent years, the development of novel processes for rare earth separation has moved beyond the earlier theory. One rare earth separation process, the so-called hyperlink process, has been developed in the past decade and proven in industrial practice to dramatically reduce both the consumption and emission of chemicals during multi-component solvent extraction separations, and therefore is now widely used in the Chinese rare earth separation industry (Liao, Wu, Cheng, Wang, Liu, Zhang, & Yan, 2013). The present article will give a brief review of the development of the theory of the hyperlink processes, and the hyperlink separation flowsheets for typical rare earth mines in China designed using the theory.HYPERLINK PROCESSES (LIAO et al., 2013)A flowsheet of multiple-component separation consists of a couple of separation units. The units of a conventional flowsheet separately consume chemicals for saponification and scrubbing and discharge wastewater with resulting salts. In contrast, the separation units in a hyperlink process are hyperlinked and thereby the chemical demands of the whole flowsheet are decreased. For a feed containing t components of A1, A2, …, and At, it has been proved in theory that the separation mode of (AtAt-1…A2)/(At-1At-2…A1) is preferred in a single separation unit. The hyperlinking between separation units can have two forms. The link between two units locating at a same separation level, such as between (A4A3)/(A3A2) and (A3A2)/(A2A1), is known as horizontal hyperlinking. The link between two units located on different levels, such as between (A4A3A2)/(A3A2A1) and (A3A2)/(A2A1), is known as vertical hyperlinking. Both the hyperlinking forms have been proven to save chemical usage and consequently to lower the pollution emissions in industrial practices as well as in theory."

Jan 1, 2016

By Rene A. Morin, John K. Kebe

"As explosives become more widely used in urban and other congested areas, governmental regulations pertaining to their use are becoming more pervasive and stringent. This is forcing the blasting industry to review its entire spectrum of operations. Greater attention is now being paid not only to the design and layout of blasts, but also to the monitoring and recording of their after-effects for both legal and business reasons.Current PracticesThe major users of explosives in urban areas are quarry operators and construction companies. A characteristic of both of these industries, at least in recent years, is a relatively low margin of profit. This, coupled with the fact that their use of explosives is relatively intermittent, prevents them from having the kind of professional consulting services that blasting operations really warrant in today's regulatory environment. When such services are obtained, they tend to be directed more at the design and execution of the blast than at the recordkeeping function. The records that are kept tend to be more in the form of a summary of the consultant's design data as opposed to the kind of after-effect detail that is necessary.The more experienced consultants and operators now realize that at least as much attention must be paid to the record-keeping as to the design work. Regulatory bodies at all levels of government are insisting on the availability of such records.Unfortunately, the instrumentation in use today for taking such measurements does not lend itself to the practice of intermittent consulting. Current monitoring and recording instruments are based on so-called analog technology of the type that has traditionally been applied to the monitoring of earthquakes. They require set-up and calibration procedures which must be repeated each time the instrument is moved, or the blasting parameters are changed, as well as complex total analysis of the recorded data. This can lend to confusion and a dilution of responsibility for anything other than the design work and possibly some summary reporting."

Jan 1, 1985

By C. Matthews, A. Vo

Australia is one of the world’s leading exporters of bulk commodities and the extensive use of sampling equipment is key to the successful management of each mining operation. At the process plant, without a full understanding of the feed, product and tails, it is impossible to fully optimise the performance of the plant, such that the metallurgical balance is often open to error. At the port, a statistically correct, bias free and compliant sampling system is crucial to ensuring exported minerals are reflective of their true value and to avoid penalties. Over the last decade, as a result of the iron ore boom, there has been high demand for reliable, representative and standard compliant solids sample systems in Australia. This paper reviews several solids sampling applications at Australian mine sites, the challenges and experience gained and how the implementation of reliable representative sampling systems has provided better understanding of plant process performance, improved plant control and overall benefits to the operations. INTRODUCTION Mining is the primary contributor to the Australian economy with Australia ranking in the top 4 in economic resources for 21 primary industrial minerals in 2016 (Britt, et al., 2017). Australia is one of the world leaders in the export of the majority of its commodities including gold, copper and iron ore (Britt, et al., 2017). Therefore, a suitable and standard compliant sampling system is essential for evaluating plant performance and content verification. At the mine and at the port, the larger iron ore miners in Australia have developed stockpile models to predict the grade of their ore down to individual blocks of the stockpile. This allows the miner to create the right blend of material for sale to their customers and ensures they are not underselling their product or at risk of penalties for impurities or low grade. As an example, the average difference between the benchmark 62% Fe and low grade 58% Fe fines at the time of this report averaged US $20/tonne according to the Metal Bulletin Iron Ore Index (Fastmarkets MB, 2019). At a shipload of 180kt this would be a variation of US $3.6M. Whilst this is an extreme example, it highlights the economic importance of producing the correct grade product and a recognised representative sample of said product.

Jan 1, 2019

By J. H. Archibald

"This paper describes the use of vector analysis for determining the intersection of mineral deposit veins. The mathematical evolution of the analysis is outlined.IntroductionMany mineral deposits can be characterized by sets of intersecting veins. Often a vein will have a steep dip and may intersect with another similar vein. Finding the intersections of these veins is usually done by graphical means. Structural geologists, by the methods of descriptive geometry, can usual ly predict where intersections of veins will occur. This method normally requires accurate drafting and layout of the problem and does not always lend itself to solution in the field.Another method for solving this problem involves the use of vector analysis, which is easily adapted to hand-held programmable calculators. It is assumed at the outset that the reader is familiar with the dot and cross products used in vector analysis. Two excellent references are cited at the end of this note for convenience.A plane, in general, is defined by three points. The points of interest here are the points where three vertical drillholes penetrate the vein, or plane, in question. The elevations of these three points are best referred to sea level. This requires knowing the elevation of the collar of the drillhole above sea level and the drillhole depth from the collar to the vein. The elevation of the intersection point is then found by subtracting the hole depth from the collar elevation. These three points now define the plane of the vein. A similar set of three points will define a second vein, and it is our object to show analytically their intersection if it exists."

Jan 1, 1983

By G. Sperlins

"IntroductionBrenda Mines Ltd. is a low-grade open-pit mining and milling operation located near Peachland, B.C. Brought into production in late 1969, the plant treats an average of 30,000 tons per day of an ore that contains 0.130% copper and 0.030% molybdenum.The operation is divided into six areas of responsibility, namely the mine, mill, plant, accounting, industrial relations and purchasing /stores departments.The purchasing and warehousing area handled in excess of 11,000 items valued at $31,000,000 in 198J. Over and above this, the warehousing area issued in excess of 74,000 line items valued at $15,000,000 during that same period.Materials Management- DefinitionWhat is meant by the term ""Materials Management""? Reference to the dictionary will reveal that a material is ""that of which anything is composed or may be constructed; the tools, instruments, implements', etc. for doing something"". Management is defined as ""the act, or manner of managing; the skillful use of means to accomplish a purpose"". Presumably combining these words defines materials management.Of greater importance are the materials managers who will carry out the function. At Brenda Mines Ltd., all employees and suppliers contribute to the materials management function. Each has a specialized knowledge of the materials used in his field. Each has a different view concerning the use and description of the same material. The key is to focus this knowledge so as to make the materials management system useful to everyone."

Jan 1, 1982

By Ros Taplin

Realizing the potential of cutting greenhouse gases (GHGs) associated with mining, a variety of approaches has been proposed for their mitigation. The Clean Development Mechanism (CDM) under the Kyoto Protocol to the UN Framework Convention on Climate Change (UNFCCC) has been a key mechanism to assist in implementation of mitigation measures. The objectives of CDM are not only to assist Annex I countries in meeting their GHG emissions reduction targets with cost-effective reduction but also to achieve sustainable development in non-Annex I countries. However, apart from China, India, Brazil and Mexico, many developing countries are still in the stages of formulation or realizing CDM strategies. Projects associated with methane capture and flaring are the fourth most prevalent type of CDM project internationally. This research primarily has addressed emissions abatement and sustainable development aims and effectiveness of registered CDM projects associated with coal mining in China. The paper reviews 30 currently registered CDM projects in China on the UNFCCC database and six other non- Chinese projects. Systematic evaluation involving content analysis of documentary evidence regarding coal mining CDM projects is presented in relation to firstly, quantitative reduction of GHG emissions and secondly, sustainable development outcomes. The projects have been assessed via a set sustainability criteria. Overall it was found that sustainable development goals are only briefly referred to in Project Design Documents, Letter of Approvals and validation documents. Varying types of sustainability initiatives have been implemented with weak to strong indications of effectiveness. This has implications for the future effectiveness of CDM projects in the mining sector, the proposed new market mechanism under UNFCCC, and for assessment of projects under mechanisms established outside the UNFCCC.

Aug 1, 2013

By Lassi Klemettinen, Ari Jokilaakso, Dmitry Sukhomlinov, Pekka Taskinen

The solubilities and distributions of molybdenum and iridium in iron silicate slag and copper-iron mattes were studied using an equilibration-quenching technique and subsequent direct phase composition analyses by EPMA (Electron Probe X-ray Microanalysis) and LA-ICP-MS (Laser Ablation-Inductively Coupled Plasma-Mass Spectrometry). The equilibrations were carried out on a wide matte grade interval, ranging from 55 wt-% Cu to 75 wt-% Cu, in pSO2 = 0.1 atm at 1300°C. The results in equilibrium with a solid iridium-molybdenum alloy indicated an iridium solubility of 150–500 ppmw in the sulphide matte, depending on the matte grade, and a molybdenum solubility of 100–600 ppmw. Iridium was distributing predominantly in the sulphide matte with the distribution coefficient of 10+3 - +4 but molybdenum deported predominantly in the slag with Lm/s(Mo) = 0.02–0.1. The effects of alumina and lime additions in the smelting slag were also examined. INTRODUCTION Iridium is a highly siderophile element (HSE), which means that it is incompatible with the sulphide forming elements and possesses a small solubility in mattes, such as copper- and nickel-iron sulphide melts. Molybdenum behaves only modestly in that way (Walker & Li, 2008; Righter et al., 2017). They both are known to be trace elements accompanying copper and nickel sulphide ores. No solubility data, however, are available for them in copper-rich sulphide mattes. Geochemical data on the behaviour of Ir and Mo deal mostly with low-iron silicate systems, e.g. basaltic melts, and high-sulphur sulphide solutions and mattes (Ertel et al., 2008; Fonseca et al., 2007). They also indicate that Ir and Mo dissolve in silicate melts primarily as oxides and not as electrically neutral metal species. Most geological data of iridium focus on high-sulphur systems of the monosulphide composition and typically Fe-Ni mattes where copper is a trace element (Fleet et al., 1996; Sattari et al., 2002). Direct solubility measurements for mattes and iron-lean silicates have also been made using pure Ir or an Ir alloy as the saturation phase (Borisov & Palme, 2000; O’Neill & Eggins, 2002; Makovicky & Karup-Møller, 1999; Ertel et al., 2008; Mungall & Brenan, 2014). A recent summary about the solubilities of HSE’s in iron- and sulphur free silicates is available in Laurenz (2012). The thermodynamics of molybdenum partitioning between oxides and Fe-S-O melts was studied by Mengason et al. (2011). Their results indicate strong accumulation in the iron-rich sulphide in reducing conditions (pO2 = 10-9.6 atm in Ni-NiO equilibrium at 1050°C). Molybdenum dissolves in iron-lean silicate melts as MoO3 species in oxygen pressures above the Fe-FeO equilibrium and as MoO2 in more reducing conditions (Farges et al., 2006; Righter et al., 2017).

Jan 1, 2019

Slurry flow, including flow through the charge, through the discharge grates, along the pulp lifters and its discharge from the mill is an important contributor to the efficiency of the grinding process within a SAG mill. Poor transport of finer ground material can adversely affect grinding leading to excess energy consumption and over-grinding of fine material. This paper extends a 1-way coupled DEM-SPH method to three dimensions and applies it to a 1.8 m diameter by 0.6 m long AG/SAG pilot mill. This provides detailed information on the internal flow of slurry within a SAG mill, including the prediction of dry regions and of slurry pooling. Full 3D analysis also allows the pulp flow patterns into and out of the mill via pulp lifter chamber to be investigated.

Jan 1, 2012

By H. E. Wilde

"Zinc has been used for many years as a galvanic coating for the protection of steel. Electrochemical measurements show that zinc actually overprotects steel. The corrosion rate of DQSK (drawing quality semi-killed) steel in air saturated salt water was determined as a Junction of applied cathodic potential. The resulting data indicate that at a critical cathodic over potential of - O. 725 Vsce an acceptably low corrosion rate of less than 1 mpy occurs. Using the developed criterion, alloys of Zn/X and AL/X were produced and evaluated in galvanic contact with steel in a standard laboratory test. The results indicate that Zn /Mn, Zn /Co, AI/Mg/Si and AI/Mg/Ge alloys offer excellent galvanic protection along with (a) no hydrogen evolution, and (b) improved dissolution life over Zn coatings.IntroductionZinc coated (galvanized) steel has been successfully used in applications where bare (or painted non-galvanized) steel would suffer corrosive attack. In general, galvanic coupling to zinc, as either an anode or a coating, is an effective means for combatting steel corrosion. Because of this, the use of galvanized steel has increased markedly, stimulated primarily by automobile manufacurers seeking to extend the corrosion warranties on automobiles(1).Although effective, zinc coatings are not without a number of drawbacks which warrant efforts to improve them. For example, because of the widely differing electrode potentials between zinc and steel ( - 1.05 Vsce and - 0.60 Vscc, respectively, in air saturated NaCl solutions), the zinc corrodes at a rapid rate to protect the steel. This is reflected in the limited lifetimes of galvanized unpainted siding. The basic electrochemistry controlling the situation is shown in Figure 1, for a system controlled by oxygen reduction. The zinc corrodes sacrificially to protect the steel, while cathodically polarizing the steel to a potential near that of zinc's open circuit anode potential."

Jan 1, 1990

By Isabel F. Barton, Matthew J. Gabriel, Mark D. Barton

Process control, mine-to-mill optimization, and other mining operations depend on having robust, comprehensive mineralogical and chemical characterization. However, current characterization methods rely primarily on analyzing samples from trenches, channels, blast holes, and drill holes and interpolating between them, and are not always sensitive to some minerals (such as clays) that cause major problems for mining and mineral processing. Continuous characterization is possible with techniques such as hyperspectral remote sensing, which measures reflectance or absorption of light in the visible to near infrared (VNIR) and short-wave infrared (SWIR) regions of the electromagnetic spectrum. Absorption and reflectance features are characteristic of different chemical bond types, so each spectrum corresponds to a different mineral or material. In remote sensing, each pixel in the scanned area has both a location and a spectrum. This makes hyperspectral remote sensing potentially useful for characterizing mine site materials. In this study, we tested a hyperspectral remote sensing system as a method of characterizing the mineralogy and material types at mine and metallurgical sites. Our test site was a small open-pit copper mine and leach operation in the southwestern U.S. We scanned mine highwalls, dump piles, leach pads, and nearby rock outcrops with drone- and tripod-mounted VNIR-SWIR spectrometers. We collected ground-truth data through geologic mapping, sampling, and spot analyses with a portable short-wave SWIR instrument. The results show that the hyperspectral remote sensing system that we tested is capable of distinguishing the types and distribution of spectrally active minerals and other materials in diverse mining settings, including showing wet and dry areas of leach pads; clay and carbonate type and distribution on mine highwalls, leach pads, dumps, and rock outcrops; plant type and distribution; fault zones, bedding planes, and other geological features; and qualitative spectral matches between dump piles and areas of the mine highwalls. Hyperspectral sensing proved particularly sensitive to the presence and type of clay and carbonate minerals, which cause geotechnical and metallurgical problems such as highwall failure, gangue acid consumption, and flotation sliming. Examples will be presented and discussed at the conference. Areas of continuing research include automating and streamlining the data reduction process, integrating hyperspectral data with block modeling and mine planning software, and testing the results of hyperspectral sensing in different geological environments.

Jan 1, 2019

By A. B. Szwilski

The paper outlines the factors taken into account for the selection of steel arch supports. The results are based on experience using the long wall system of coal mining where roadway closure can be extreme. Results of tests on scale-model steel arches and full-scale yield elements are also presented.

Jan 1, 1979

By M. R. Henzinger, W. Schubert

"The quality of the backfill applied at a shield driven tunnel is of significant importance failure of the lining. The used material also affects the interplay between support and excavation behaviour.In this research the state of the actual bedding situation is investigated by an analytical approach, laboratory tests and numerical simulations. The numerical simulation using continuum methods have shown shortcomings. These shortcomings regarding the instability of large strain simulations restrict the possibility to reproduce the relocation of the backfilling material. The performed scaled model tests have shown that the regripping process of a double shielded tunnel boring machine affects the soil failure within the gap. With the analytical results the influence of the wall friction can be predicted. Therefore the angle of the failure surface can be determined. The results have shown that the wall friction significantly increases the failure angle. INTRODUCTIONFor tunnel boring machines (TBM) with single (SM) or double (DSM) shield, precast liningsegments are used as rock support. These segmental linings are installed within the protection of the TBM shield. In order to reduce the friction while advancing, the shield diameter is smaller than the diameter of the cutter head and therefore also smaller than the excavation boundary. The difference depends on the expected radial convergences. Since the lining segments are mounted within the shield the steering gap between the shield and the excavation boundary increases and is hereinafter called annular gap.In the process of tunneling in hard rock, the annular gap is usually filled with fine grained and closely graded gravel, termed as pea gravel. The backfilling process starts as soon as possible after the shield tail passes the lining. Due to the operational procedure within the working area of a TBM, a fully backfilled annular gap might not be established after every ring closure. This leads to an unfavorable distribution of the pea gravel leaving the segmental lining partially without bedding. Segmental linings can develop sufficient resistance only when properly bedded."

Jan 1, 2015

By P. E. Weidmark

"PART 1-Published PapersAllcott, G.A., and Archibald, D.E.; ""Description of pillar behaviour at Heath Steele Mines""; Can Min Metall Bull; 74:834:80-87; 1981.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of rock Mechanics; 3:32-33; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:37-38; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:38; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses"" ; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:41; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:42; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:46; 1979.Baar, C.A.; Discussion of Theme 2: ""Tectonophysics""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:60; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3: 116; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:116-117; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:117; 1979.Baar, C.A. '; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:118-119; 1979.Baar, C.A.; Discussions (2) of Theme 4: ""Underground openings""; Proceedings 3rd Congress lntnl Soc of Rock Mechanics; 3:119; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:120-121; 1979."

Jan 1, 1982

By John E. Udd

"Mining research at CANMET is delivered by the Mining Research Laboratories Division (MRL), with facilities in Sydney, Nova Scotia; Bells Comers, Elliot Lake, and Sudbury, Ontario; and Val d'Or, Quebec. This paper gives an overview of the work of the Division as of early 1993. An addendum, at the end of this paper, describes the organizational changes that will take place in April 1994. IntroductionCANMET, the acronym for the Canada Centre for Mineral and Energy Technology, is the name by which the organization founded in 1907 as the federal Mines Branch is presently known. The name was changed in 1974, in order to give recognition to the importance of both minerals and energy technologies in the activities of the Branch. Further reorganizations have taken place since 1987. As a result of these, CANMET has assumed the status of a Sector (equivalent to the Geological Survey of Canada) and has been organized into four branches.The organization as a whole functions in an environment of semi-matrix management. Some of the ""line"" Divisions report to Directors-General for the appropriate branches while other, larger divisions, report directly to the Assistant Deputy Minister.The second dimension of the organizational matrix is composed of a number of ""staff' divisions which report to the DirectorGeneral for Policy and Planning. Each of these Divisions performs a function which is common to all of the ""line"" divisions. For example, the Research Projects Office is responsible for monitoring the range of research activities of CANMET and for recommending allocations of funds for both research contracts and operating budgets. The Library and Documentation Services Division is responsible for CANMET publications and information services. Likewise, the Engineering and Technical Services Division provides support through, among other services, the construction of specialized laboratory equipment."

Jan 1, 1994

By Xianglin Yang, Hong Zhong, Jingjing Xiao, Guangyi Liu

"The selective adsorption of a flotation collector to a mineral plays a crucial role in enhancing the hydrophobicity of targeted mineral particles for attaching air bubbles in pulp. The recent progress of the structure-reactivity relationship of flotation collectors, the characterization methods for mineral surfaces with adsorbed collectors and their commercial application are reviewed in this paper. Particular emphasis is placed on the density functional theory (DFT) for understanding the reactivity of new collectors, the surface analysis techniques including time-of-flight secondary ion mass spectrometry (ToF-SIMS), in situ scanning electrochemical microscopy (SECM) and atomic force microscope (AFM) to characterize mineral/collector interface, and the flotation technologies for optimizing recovery of valuable minerals. Especially, the recently developing collectors such as Gemini, alkoxyalkylthiourea, dithiourea, amide-hydroxamate and oximido-thiol surfactants, and their specificity to given minerals are evaluated. Based on this crucial review, it is evident that the structural modification approaches for minerophilic or hydrophobic groups, and combined surface analysis approach for further understanding the adsorption mechanism of collectors on mineral surfaces will lay a solid foundation for the future development of flotation collectors. INTRODUCTIONIn mineral processing, flotation is the main process for separation and recovery of valuable minerals from the ores contained them (Fuerstenau et al., 2007). One of the key requirements in flotation process is to increase selectively the surface hydrophobicity of the targeted minerals by collector adsorption so that these mineral particles can preferably attach to air bubbles in a slurry or pulp (Fuerstenau et al., 2007). Flotation collector is a kind of functional surfactant, which is composed of polar and non-polar groups (Somasundaran, & Wang, 2006). Non-polar portion, commonly being linear, branch or ring hydrocarbon group, is termed hydrophobic group. The polar portion, exhibiting strong affinity to mineral surfaces, is known as minerophilic group (Nagaraj, 1988). According to mineral types including saline, oxide and sulfide minerals, flotation collector divides into sulfide and oxide mineral collectors. For efficient recovery of valuable minerals from the refractory complex ores, insights into the adsorption mechanism, hydrophobic model and subsequent flotation approach of flotation collectors have been regarded as an indispensable issue in mineral processing."

Jan 1, 2016

By E. Ghali, A. D. Bas

"Treatment of oxide, e.g. roasted gold ores has received relatively less attention than sulphidic ones and recently, handling of oxide gold ores is becoming essential. In this study, the influence of roasted gold ore (RGO) slurry (at 35% solid ratio) on the electrochemical dissolution of gold has been examined using pure gold and iron oxide minerals (hematite, maghemite, and magnetite) as disc electrodes by zeroresistance ammeter mode either in one or two separate containers. The presence of slurry decreased galvanic currents, i.e. corrosion rates due to the release and increase in the amount of soluble and/or insoluble species that could retard further the anodic behaviour of gold. Higher galvanic currents were observed in two separate containers than that in one container indicating the primary importance of galvanic interactions. SEM-EDS results observed iron hydro/oxide coatings on gold surface in case of magnetite test. However, in case of RGO electrode it is not a perfect passivation, although somewhat decreasing trend was observed on gold dissolution. These findings have revealed that passivation is not only a laboratory phenomenon, but also it could be responsible for the slowdown of gold dissolution in industrial practice.INTRODUCTIONThe cyanidation of gold is an electrochemical corrosion process thus; the dissolution of gold can readily be studied by electrochemical techniques. The outcome/summary of previous electrochemical studies of gold leaching can partially be summarized as follows: Filmer (1982) and Lorenzen and van Deventer (1992) reported the negative effect of pyrite and pyrrhotite on gold leaching due to the galvanic interactions; Aghamirian and Yen (2005) studied gold galvanic corrosion in presence of sulphide mineral electrodes only in one cell using zero-resistance ammeter (ZRA) mode; Dai and Jeffrey (2006) discussed, individually, the anodic and cathodic behaviours between gold and sulphide minerals, and Azizi et al. (2010, 2011) used a bed reactor to examine the influence of sulphide minerals on gold dissolution in one and two separate cells. Accordingly, a slowdown in gold leaching has generally been attributed to the passivation phenomenon, although the indication of this phenomenon is still an undergoing debate. For instance, Mrkusic and Paynter (1970) identified the passivation as the film formation of dissolved species from calcine, Crundwell (2014) explained passivation, in the case of corrosion of metals, as the formation of a layer which is composed of a new chemical species on the mineral surface and this layer inhibits or blocks further reactions. He suggested that passivation is related to the oxidation of the metal, and the formation of a passive layer that retards the rate of dissolution by several orders of magnitude. Consequently, galvanic interactions, passivation phenomena, or combinations of them are considered significant electrochemical factors affecting gold dissolution (van Deventer, Reuter, Lorenzen, & Hoff, 1990; Azizi, Petre, & Larachi, 2012). It is important to note that generalizing the influence of a mineral/metal on gold dissolution may not be correct in all cases, since contrary behaviours/results (for pyrite) have been observed (Aghamirian & Yen, 2005). Therefore, electrochemical study of gold is still a subject of research and need to be examined further in detail."

Jan 1, 2016

By Irving Wigden

The world is fast becoming information based. Mine companies migrate business infrastructures to be handled electronically. Suppliers move onto the worldwide web. In this ?e-world? successful suppliers will recognize they no longer trade in just equipment, but in knowledge. Companies can no longer just provide products and services, but instead must find ways to harness their knowledge to provide new value for customers. Mine customers will be attracted to suppliers that can help them streamline the process and use Information Technology to optimize operations, increase profit, reduce cost and enhance shareholder value. With the continued move to industry standard communications and software platforms, technology that formerly stood alone can now be integrated with other technologies. This creates more powerful systems that mine operators can use quickly, easily and cost effectively. These unified architectures improve productivity, provide higher asset optimization and allow more informed decision-making. As a leading supplier of process automation solutions for the industry, ABB provides a dynamic range of such control systems. These systems are designed for instrumentation controls, variable speed drives, electrical distribution, electrical equipment and related services for Mine Automation. Enhanced by ABB´s new family of integrated software solutions ? collectively known as Industrial IT ? ABB´s control and Scada systems place you in the best position to optimize your plant, process and enterprise operations. The paper discuss system integration and installation of High-Tec system in an underground mine. ABB has the ambition to be a System Integrator and co-operate with partners in different areas of technology. To day it is a problem to find one Supplier that can be responsible for the complete Automation System. The design of the system is also much depending of the design of the mine and also which caving procedure that is used in the current mine. Much of the work must be done in a feasibility study and during the design phase. If there is careful planning and consideration during these phases is vital in order to avoid costly changes during the commissioning phase The paper will also include a presentation of the benefit of using Automation in an Underground Mine, and how important the integration of the Human Being is to the Automation System. The most profit gained in mining industries are received when the mines can reduce internal and external disturbances in the production flow and speed. Must of the experience and discussed in this paper is from advanced technology, that has been developed in Scandinavian and adopted of LKAB in Kiruna. The author of this paper has been responsible för the Automation projects in the Kiruna Mine during 1994 - 1999. These projects include: Broadband communication of data, audio, compressed video in one data stream. Control System for Haulage -1045m Automation of Load Haulage and Dumping machines (LHD) Control of Production Drilling Riggs from a Central Control Room.

May 1, 2002

By Ken Musgrave

"What Most Effective Management Does?It must satisfy the demands, of three groups of people: owners, employees and the public.OwnersOwners want profitable operations that will pay them a return on their investment, plus operations managed for long life. Many owners are also concerned with employee's well being and their company's public image.EmployeesJob security and a good income are probably still the most important demands, however, as time goes by, employees are also demanding more involvement in safety issues, working conditions, and even how work is done.The PublicThe public requires acceptable environmental standards, as well as enjoying the prosperity supplied by a successful operation.How are Mines Managed?Most mines are managed very traditionally. The basic credo is that the managers make the decisions, and the hourly, and junior salaried employees do what they are told. Clearly this is the extreme case, epitomized by the long service shift boss who might say ""It took twenty-years to become a shift boss, and no miner is going to tell me what to do"" .There are some exceptions, two notable ones being Campbell-Chibougamau, and T.G.S. (now Kidd Creek Mines) which, in very different circumstances, decided on a more participative style.Campbell-Chibougamau, having closed down due to unprofitable operations, reopened, using a team structure with working leaders, and a system for sharing gains against cost targets with employees. Although the system has some problems, and development miners are bonused conventionally, this has been a basically successful program.Texasgulf Sulphur, a company with a history of non-union operations, and a participative management style, made a corporate decision to operate their Kidd Creek Mine in the same way. The orebody was rich enough to allow them the luxury to do this, but they have never had a strike, so perhaps they have more than saved the cost of the benefits and salaries they needed to pay. They also reward employees with a stock distribution scheme based on service and earnings."

Jan 1, 1985