Search Documents

By D. D. Hogarth

"IntroductionThe Hull iron range, comprising the Forsyth, Scott , Baldwin and Lawless properties (Fig. I), is in Gatineau Park, on the outskirt s o f the city of Hull , and about 6 miles (10 kilometres) northwest of the Federal Parliament Buildings.The deposits have been known many years and described numerous times, although the history has been treated lightly in former publications. Total ore shipments have been calculated at 122,700 long tons, of which over 80% were mined before 1900 and 74% in two brief periods: 1870-74 and 1880-82. It is surprising that the period 1870-74 has been overlooked by most authors and 1880-82 ignored altogether. More surprising, the essential data for these two periods are contained in manuscripts of the Robert Bell collection, which must have been available to officers of the Geological Survey o f Canada.The period 1801-1874 ha s already been covered by the writer in ""Pioneer mines”, but much information has come to light since publication. The present paper is therefore based o n new data and a fresh appraisal. However, little additional data were found for the early history (1801-1854) or for the legal cases involving A.H. Baldwin, and these parts were mainly summarized from the relevant sections of the above-mentioned publication.GeologyThe ore deposits are all situated somewhat below the middle of a graphitic, calcitic marble horizon, here folded into a northeast-plunging synform. The Forsyth, Scott and Baldwin deposits are on the south limb of the synform; the Lawless is on the north limb. The marble is underlain by three non-carbonate groups: biotite gneiss with interlayered quartzite (top), granite gneiss and skarn (middle), and biotite-garnet gneiss (bottom). Below these groups is a lower horizon of graphitic, calcitic marble. The whole sequence is Precambrian and has been subjected to high-grade (Grenvillian) metamorphism, but, in the north, is cut by an unmetamorphosed Cambro-Ordovician diabase dyke. For further information, the reader is referred to the summary by Baird."

Jan 1, 1983

By H. Tudeshki

A great amount of aggregate is utilized in civil engineering applications such as road construction, railway infrastructure, concrete production, etc. Igneous rocks are the preferred raw material due to their high strength and abrasion resistance. Rock quality assurance is a key factor and has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous aggregate rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure, i.e. disintegrate and degrade. This phenomenon has a great influence on the quality, strength and durability of aggregates. In the last decades, different methods and procedures such as the glycol test, the methylene blue dye test, as well as the Los Angeles test, have been introduced to distinguish rock properties, and to identify these problems. However, as these wet-chemical methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and are only possible to be accomplished under laboratory conditions, their application has always been severely limited. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used in the day-to-day routine of a mine for quality control of the quarry´s daily production. Our research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. Our new approach is based on two rock parameters: magnetic susceptibility and loss on ignition. The measurement of these parameters provides reliable information on the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. Our new approach has been assessed through extensive field and laboratory studies and has been implemented on the drill-cuttings of a basaltic andesite quarry. The results of the experiments are discussed in detail, including their impact on increasing resources and environmental protection.

Aug 1, 2013

By T. Alan O'Hara

"Annual mining revenue can be computed by formulae relating metal prices, smelting schedules, concentrate grade and recovery to known ore grade and an assessment of core samples. Operating costs at different daily tonnages are related to orebody shape, mining method, milling process and general plant services. Capital costs are related to sizing of mining equipment, mine development, plant-site topography, climate and accessibility, plant services and personnel housing. IntroductionA crude guide to the average 1978 cost of mine projects is shown in Figure 1, but the costs of many mine projects have differed widely from the graphed average costs of $800,000 T0.6 for underground mine/mill projects and $400,000 T 0.6 for low-grade open-pit mine/mill projects.High mine project costs and high operating costs are characteristic of open-pit mines with high stripping ratios, underground mines with thin orebodies, mills with complex metallurgy, and projects located in isolated regions with severe climate, mountainous topography, and lacking access to existing roads, towns and electric power. When none of these adverse conditions prevailed, the mine project cost was typically much less than the graphed average cost. Virtually all the conditions likely to cause high capital and operating costs are known from knowledge of the local topography, climate or accessibility, or can be assessed by tests on core samples, as soon as the orebody has been outlined by drilling .A more accurate estimate of over-all project capital cost and operating cost can be made from a summation of items of cost after judging the effect of specific local conditions on each item of capital and operating cost. This paper offers guides in judging the effect of local conditions on the sizing and 1978 cost of specific items of capital cost and operating cost and operating cost of mine projects. When the specific items of capital cost and operating cost are totaled and measured against expected net revenue and taxes over the life of the mine using the net-present-value or discount-cash-flow methods, the result should show whether the mine project development is clearly feasible, doubtfully feasible or clearly uneconomic. If the development of the mine project is clearly feasible, or probably feasible, a detailed feasibility study by experienced consulting engineers should be commissioned before any financial commitments are made; but if project development appears to be uneconomic, the time and cost of a detailed feasibility study is not warranted."

Jan 1, 1980

By L. Gasser, N. Bellinger, H. Awatta, A. Merati

As aircraft age, the extent of interactions between fatigue and other damage mechanisms, such as corrosion and fretting, increases. At present, however, there is no generally accepted methodology within the Aircraft Structural Integrity Program (ASIP) framework to account for the effects of these interactions on life and the residual strength of aging aircraft components. A comprehensive program is being carried out by the National Research Council Canada in collaboration with Analytical Processes/Engineered Solutions, using the Holistic Structural Integrity Process (HOLSIP) to address time and cyclic load issues. This approach predicts the evolution of a discontinuity state in a material from production to retirement. This paper summarizes the results of a study on the 2024-T3 aluminium alloy in different forms (clad and unclad), thickness, and specimen geometry. This study consisted of identifying the microstructural features associated with crack nucleation sites and relating them to the testing parameters and fatigue life. Several coupons were fabricated and fatigue-tested. The fracture surfaces were carefully examined, and the physical characteristics of the microstructural features found near the crack nucleation sites were analyzed. Effect of stress level, loading direction, coupon geometry and surface condition on the number of crack nucleation sites, and fracture origin size has been discussed. Four distinctive mechanisms were found to be responsible for crack nucleation: for unclad materials constituent particles, oxide residue, surface irregularities and for clad samples the clad layer was the sole fracture origin.

Jan 1, 2006

By A. Mukherjee, C. Kelly, B. Markovich, G. E. Agar, G. E. Robertson, F. Khan, B. Shea

"Laboratory batch flotation tests were performed on a sample of bulk slow cooled converter matte (Cu:Ni = I) to optimize the time in each of the separation stages. Numerical simulations were carried out to estimate a continuous circuit material balance for the conditions selected. An experimental simulation of a continuous circuit (locked cycle test) readily came to steady state and there was reasonable agreement between the numerical and experimental results. The use of nitrogen as the flotation gas and the addition of collector to the grinding mill minimized the oxidation of chalcocite, which has previously resulted in increasing circulating loads, and led to a stable circuit with very low weights in the recycle streams.IntroductionINCO Limited developed a flotation process for separating the components of copper-nickel matte [Sproule, Harcourt and Rose 1945; Sproule, Harcourt and Renzoni 1960] in 1945 to replace the Orford process and continues to use the flotation process in almost the original mode to this day. Initially the matte processed was the result of smelting a nickel concentrate that analyzed about 12% nickel and 2% copper and all of the recycle material that was generated in the smelting process. The matte generated analyzed about 25% copper and 53% nickel, roughly 2: 1 nickel to copper. This matte was blown in Pierce-Smith converters to be sulfur deficient in order to produce a metallic phase that collected the precious metals contained in the smelter feed [Wilson and Stratton-Crawley 1991]. This process continued with little change until 1994 when the separation of chalcopyrite from pentlandite in the Copper Cliff mill was discontinued after 63 years of operation. As a consequence of the elimination of the primary separation of chalcopyrite from pentlandite in the milling process a bulk concentrate was produced for smelting. Bulk concentrate smelting came into practice in 1994 as part of the initiative to meet government legislation that restricted the emission of sulfur dioxide to the atmosphere. Previously, the copper concentrate was smelted in an INCO oxygen flash furnace which resulted in the capture of a high strength sulfur dioxide stream from which liquid sulfur dioxide was produced. Nickel concentrate was smelted in reverberatory furnaces that produced low strength sulfur dioxide gases which were difficult to treat. The action taken by INCO to meet the environmental constraints was to smelt a bulk concentrate in oxygen flash furnaces which would produce gases suitable for the production of liquid sulfur dioxide and another stream that was high enough in sulfur dioxide to be readily converted to sulfuric acid [Bell et al 1990]. The end result of this decision was that all the copper-nickel separation would be done in the matte separation plant."

Jan 1, 1996

By P. M. STILES

Acquired in 1957, the limestone quarry of Ideal Basic Industries on Texada Island north of Vancouver has become a major supplier of high purity limestone and construction stone. Crushed limestone products are shipped by barge to various destinations along the B.C. and northern U.S. coasts.

Jan 1, 1984

By Derek E. McBride

"Exploration work in the Beardmore - Tashota area has led to a reinterpretation of relationships between gold mineralization and the geologicalevolution ofthe area. The host volcanic rocks form two parallel volcanic belts connected by a much smaller cross-cutting band, which trends northeast from Beardmore to Tashota. This connecting band consists of mafic and felsic volcanic, plus clastic sedimentary rocks in a sequence conformable with the contact of the Onaman Lake Batholith to the east. A metamorphic aureole or incorporated xenoliths are lacking along this major contact and the only intrusive relationship observed is chilling between mafic dikes and a cold host granite in proximity to it. Granite dikes are totally lacking in the volcanic succession, or the overlying sedimentary sequence. A major part of this sequence consists of a polymict basal conglomerate with granite boulders and volcanic clasts in a fine-grained chloritic matrix. The nearest source for these boulders is the Onaman Lake batholith.Gold mineralization in significant economic quantities (+ 50 000 ounces) occurs at the top or above the mafic volcanic succession as quartz bands. In the Northern Empire Mine, the band is conformable, folded, boudinaged and the mineral zoning shows a relationship to variations in the host rock, not structural overprinting. In general, where the host mafic tuff is medium-grained, the quartz band is thicker, up to a metre wide, and carries economic grade; where the tuff is finer-grained and bedded, the band is very thin and low grade.Stratigraphic control and metal zoning shows that the mineralization formed as part of the development of the volcano- sedimentary succession. The other major deposits in the area (Leitch and Sturgeon River) have a similar structural history suggesting that they are also syngenetic in terms of the stratigraphic development. Regionally, these deposits were emplaced prior to any significant tectonic deformation but at the end of the mafic volcanic event.The mafic activity was related 10 a period ofextension which caused the volcanic troughs to develop along centres of rifting. The hiatus at the end of this event permitted extensive hydrothermal systems to form and deposit siliceous exhalite bands within sedimentary or terminal mafic volcanic environments in promixity to major thermal sources. Subsequently, the Kenoran Orogeny deformed the entire succession into upright folds with a sub-vertical schistosity. Evidence shows that the deposits have remained intact since deposition."

Jan 1, 1987

By Matthew S. Hall

Gold/iron oxide catalysts have been prepared and their catalytic performance evaluated for low temperature CO oxidation. The method and temperature used to dry the sample has a significant effect on their catalytic activity. Analysis by TEM revealed the catalysts contained Au particles, although catalysts with high and low activity did not always differ in their microstructure as evidenced by TEM. Catalysts were characterised using XPS and the difference between the Au(4d) and C(1s) binding energies measured; in general the greater the difference, the higher the catalytic activity of the material.

Oct 1, 2003

By Michael L. Free, Zongliang Zhang, Joshua M. Werner

In the copper electrowinning process, short-circuiting between the anodes and the cathodes is a critical problem that changes the current allocation among local electrodes and reduces the current efficiency significantly. Possible reasons for the short-circuiting include the improper alignment of the electrode, bent electrode, and nodules on the cathode surface. In typical tankhouses, there is often a time between shorting and harvesting as well as between shorting and clearing. Therefore, it is inevitable to have short-circuiting affect the operation performance in practical electrowinning operations. However, one key piece of missing data is the actual measurements of the current efficiency as short-circuiting is approached and allowed to continue. Consequently, short-circuiting tests that allow tracking of electrowinning parameters before and after short-circuiting were performed in a laboratory scale Cu electrowinning cell. In the tests, the electrode spacing change, the mass of electrodeposited Cu, the deposition morphology, and the current allocation as well as the current efficiency before and after short-circuiting were studied. Results show that the short- circuiting affects the current allocation and the current efficiency significantly. Moreover, it changes the Cu deposition on the short-circuited cathode and therefore causes problems for Cu electrowinning. INTRODUCTION Electrowinning (EW) is commonly used for copper production around the world, with a rated production from 120,000 to 200,000 tons per year per operation (Wiechmann, Aqueveque, Henríquez, Muñoz, & Morales, 2014). In Cu electrowinning, Cu ions in the electrolyte are reduced on the cathode surface as metallic copper with a DC current, while on the anode, a counter anodic reaction occurs with oxygen gas generation (Werner, Zeng, Free, Zhang, & Cho, 2018; Zhang, Werner, & Free, 2018; Zhang, Werner, & Free, 2018). In copper electrowinning, an average current density of 200 to 400 A/m2 is applied to the electrowinning cell (Wiechmann et al., 2014). As the Cu deposits on the cathode, the distance between anode and cathode reduces and most of the time, short-circuiting forms between some anodes and cathodes in a large tankhouse containing thousands of electrodes, reducing the current efficiency and increasing the energy consumption significantly. The current efficiency in well-run copper EW operations is typically above 90 %. Most of the unused current is wasted through short circuits, stray currents, and by-byproduct formation (Davenport, King, Schlesinger, & Biswas, 2002; Wiechmann, Vidal, Pagliero, & Gonzalez, 2002; Wiechmann, Morales, & Aqueveque, 2010). Usually, in the tankhouse, the short-circuiting increases the current in the involved cathode by up to 1500 A (Wiechmann et al., 2010). Multiple reasons can cause the short-circuiting in the cell, and the most common reasons include the uneven current distribution among cathodes, tilted electrodes, bent electrodes, and nodules formed due to the large deposition roughness. Recognition of this challenge in the Cu electrowinning process has led researchers to perform many investigations on approaches to avoid and reduce the short-circuiting in the cell. A series of research investigations have been conducted to develop and improve a new type of intercell bar for Cu electrowinning (Wiechmann et al., 2002; Wiechmann, Morales, Aqueveque, & Burgos, 2007; Wiechmann, Morales, & Aqueveque, 2009; Wiechmann et al., 2010; Wiechmann et al., 2014). The associated test results show that this new design limits the occurrence and magnitude of short circuits and allows operation at higher current densities. Sandoval, Clayton, Dominguez, Unger, and Robinson (2010) stated several keys to control short circuits, such as maintaining the straightness of the cathode, removing “edge hair” from the cathode starter, and maintaining electrode alignment in the cell. Prengaman and Siegmund (1999) from RSR technologies developed a new Pb-Ca-Sn anode to prevent the anode deformation, thereby reducing the short-circuiting in the Cu electrowinning cell. Although the negative effects of short-circuiting on the Cu electrowinning have been recognized, and various investigations have been conducted to address this issue, the actual measurements of the electrowinning behavior and performance as short-circuiting is approached and allowed to continue are seldom reported. However, in typical tankhouses, there is a time between when shorting occurs and harvesting/clearing are performed. One key factor in determining the harvest time is the frequency of shorting. Consequently, we have performed short-circuiting tests that allow us to track electrowinning parameters before and after short-circuiting.

Jan 1, 2019

By K. Hashiba, Y. Z. Liang, K. Fukui, M. Koizumi

"Efficiency and penetration rate during percussive rock drilling significantly affect the speed of tunneling and excavation. Many researchers and engineers have continuously engaged in the advancement of rock drilling performance. Development and modification of the rock drills based on test data are timeconsuming and costly. Hence it is essential to make effective use of numerical simulation. However, most of the numerical models proposed in previous studies were too simple in comparison with the actual percussive rock drilling in which many factors are involved. The objective of our research project is to construct a new realistic numerical model of continuous percussive drilling, which is based on the previous Okubo-Nishimatsu’s model. In this study, the parts of the previous model involved in stress wave propagation and attenuation were modified. The two models were prepared for HD712 hydraulic rock drill mounted on crawler drills and HD210 hydraulic rock drill mounted on drilling jumbos. Stress wave propagation was computed with the discretized one-dimensional wave equation. The calculated results were compared to the stress waves measured on a rod during percussive drilling. In both models for HD712 and HD210, the measured stress waves can be reproduced with the one-dimensional model of the same acoustic impedance as the actual piston, shank rod and rod combined with the CI+spring model as a rod joint. The calculated results indicate that the spring constant in the model of a rod joint needs to be set appropriately depending on drilling conditions. INTRODUCTIONEfficiency and penetration rate during percussive rock drilling significantly affect the speed of tunneling and excavation. Many researchers and engineers have continuously engaged in the advancement of rock drilling performance. Components related to the percussive drilling are a drill body, a piston, a shank rod, rods, rod joints, a bit and rock. The piston in the drill body is reciprocated by hydraulic pressure and collides with the shank rod a few thousand times per minute. Stress waves generated by the collision propagate and attenuate in the rods and rod joints, and then reach the bit. The bit penetrates and crushes rock. During percussive drilling, the components mutually affect each other and self-induced oscillation occurs. The number of blows and the rate of penetration are determined by the practical drilling conditions such as hydraulic pressure, thrust force, number of rods and mechanical properties of rock. Development and modification of the rock drills based on test data are time-consuming and costly. Hence it is essential to make effective use of numerical simulation. However, most of the numerical models proposed in previous studies were too simple in comparison with the actual percussive rock drilling in which many factors are involved."

Jan 1, 2015

By K. Esmaieli

ABSTRACT We conducted a series of numerical experiments to investigate the influence of rock mass foliation on impact-induced damage on ore pass walls. The 2D Particle Flow Code was used to simulate three distinct rock masses surrounding an ore pass, characterized by foliation angles of 60°, 90°, and 120° (clockwise from horizontal). Subsequently, we projected a rock fragment against the ore pass walls at a constant impact angle and velocity. The resulting damage increase

Jan 1, 2014

By Fathi Habashi

Poland has a unique copper industry. Copper sulphide concentrates are smelted in six shaft furnaces to produce matte and in a flash furnace directly to blister copper. Anodic slimes from electrorefining are treated by a modern technology to recover the precious metals. INTRODUCTION Poland's copper industry began in 1950 when the old and relatively small mines Lena and Konrad, located in Lower Silesia, were drained and recommenced production. In 1957 the industry entered a period of rapid development with the discovery of a rich ore body in the vicinity of Lubin and Polkowice which was the basis for the establishment, in 1961, of the Copper Mining and Smelting Combine (KGHM). In 1991 the Combine was restructured into a state-owned, joint-stock company under the new name of KGHM ?Polska Miedz? (KGHM ?Polish Copper?). It consists of three mines, three smelting and refining plants, and one rolling mill, and produces about 4% of the world?s copper and about 7% of the world?s silver.

May 1, 2001

By G. W. Clark

"The mining of the ore bodies at Rabbit Lake has in the past been by the open pit method. This method is presently being used to develop the B-zone and will continue into the future with the development of two smaller ore bodies, the A-zone and D-zone. The Eagle Point orebody will be developed by an underground method which will provide production and employment into the next century.The ore bodies at B-zone, A-zone and D-zone are unique in that they are located under Wollaston Lake. To permit mining by the open pit method a steel-celled dyke has been constructed around the north end of the B-zone. This same dyking method will be used for the A -zone and D-zone. INTRODUCTIONMine development at Rabbit Lake commenced in 1970when a detailed engineering feasibility study established the viability of the Rabbit Lake deposit. In 1972 construction of the mill and camp site began. Construction materials were seasonally hauled to the site over a winter road until November 1973when the government of Saskatchewan completed an all-weather road to within six miles of the operation.In October 1974, stripping of the Rabbit Lake open pit began with the removal of overburden and lake bottom sediments from the previously drained Rabbit Lake. The first ore was processed by the mill in June 1975and by October the mill was producing three million pounds per year. The design capacity of five million pounds annually was first achieved in 1977 and maintained until 1981, when lower ore grades resulted in lower production rates .It was clear when mining at Rabbit Lake began that, without additional reserves, the Rabbit Lake operation had a life of less than 10 years. Exploration, therefore, continued in the immediate area in an attempt to discover additional uranium mineralization."

Jan 1, 1989

By I. H. Warren, F. A. Forward, A. Vizsolyi

"Observations are reported on the pressure leaching of material produced by subjecting chalcopyrite to two types of heat treatment. Calcination of the mineral at 825°C, in the absence of oxygen, induces some sulphur loss by volatization, producing a material from which copper can be leached more rapidly than from chalcopyrite. Treatment of the mineral with elemental sulphur at 475°C leads to sulphur uptake accompanied by a change in mineralogical structure of the chalcopyrite. Copper is prefer-entially and rapidly leached from the sulphur-treated material. A tentative explanation of the sulphur-chalcopyrite re-action is presented."

Jan 1, 1968

By A. A. Levinson, M. B. Kirkley, J. J. Gurney

"Scientific advances in the past decade have greatly clarified our understanding of certain concepts relating to the age and origin of diamonds. These advances are largely the result of geochemical studies of mineral inclusions in diamonds, made possible by modem analytical techniques which enable the accurate chemical analysis of micro-sized particles of the order of 200 microns in maximum dimension. As a generalization, the inclusions indicate that most diamonds formed from either of two rock types, peridotite and eclogite. Peridotitic diamonds have yielded ages of 3300 million years, whereas eclogitic diamonds areyounger and rangein agefrom approximately 1000to 1600million years. Kimberlite and lamproite, the two rock types usually associated with diamonds, typically are much younger than the diamonds they contain. Thus, it is now dear that kimberlites and lamproites are only the transporting mechanisms which brought diamonds to the surface and are in no way related to the formation of most diamonds. The latest concepts which developed during the past decade regarding the sources of carbon for the crystallization of diamonds from peridotite and eclogite, and the mechanisms of kimberlite and lamproite emplacement, IntroductionThe decade of the 1980s has seen major advances in our understanding of the age, origin and emplacement of diamonds. The information presented herein is applicable to virtually all natural diamonds, excluding diamonds related to meteorite impacts. There is still some question, however, as to the applicability of the new information to industrial grade ""fibrous"" or ""coated"" diamonds, and to microdiamonds (< 1 mm). In addition to drawing upon our own experiences, this review is summarized from a voluminous literature and for those interested in the original sources we recommend the books by Mitchell and Bergman (1991), Ross (1989), Nixon (1987), Mitchell (1986), Glover and Harris (1984) and Dawson (1980), and the review articles by Mitchell (1991), Gurney (1989) and Meyer (1985).are also discussed."

Jan 1, 1992

By F. Prescott, D. Hiam-Galvez, J. Hiam

Mines are frequently located in remote areas with little conventional employment and few opportunities for the existing population. The development and operation of the mines results in several years of intense activity followed by a near-complete reduction in employment and opportunities after the mines are closed. Designing Sustainable Prosperity (DSP) is a method for rectifying this situation by designing for long-term growth in areas that host mines. This process involves the participation of local and national governments, local community, mining companies, investors, academics and those with sector expertise. The mines will be the catalyst for regional sustainable development. If successful, long-term economic and environmental prosperity should be the result for the areas affected by mining and, in some instances, promoting the regions as centres of excellence for a particular industry. This paper will describe how the concept works using the copper producing region of Peru and Chile as an example. Designing sustainable prosperity starts by looking at regions based on the natural resources and skills available, the infrastructure and possible energy sources. Integrated natural resource models and innovative market studies, followed by education and skills requirements, are then established to determine the potential for the region and what needs to be done to realise the possibilities. INTRODUCTION Industry 4.0, or i4.0, dubs the fourth and current industrial revolution. Where previously they have been founded on ever-increasing consumption and production, i4.0 distinguishes itself by its partial focus on reducing resource intensity; lightweighting, energy efficiency, sensors and automation to improve resource efficiency. Industry 4.0 is an era of artificial intelligence, genome editing, biometrics, renewable energy, 3D printing, autonomous vehicles and the Internet of Things (Lu, 2017). These drivers represent key opportunities for the economic future of nations and regions.

Jan 1, 2019

By Matthew Janes

Advantages: Clean samples Low sample disturbance Very low spoil Versatile Fast Penetrates all formations Resonant Drill 100 or 150 kW Self tuning to resonance Rotation to 100 rpm Increased depth in dense soil Increased productivity Reduce water use Reduce casing plugging

May 1, 2013

By Donald O. Downing

"IntroductionThis paper provides an overview of the coal mining industry in Canada with a description of current circumstances. The Canadian industry is placed in a global context and the future prospects of the industry are described. The export market is very important to the future of Canadian coal production and the essential aspects of the market are explained. Future prospects are very much tied to metallurgical coal exports and some key characteristics of that market are discussed, including major technological changes in the industry. Stability in 1996The Canadian coal industry enjoyed another strong year in 1996 continuing a trend established over the last four years. The strength of the industry is based on a stable domestic industry and a relatively healthy inter- national market. The figures bear out these statements. In 1996 total production reached 75 million tonnes and consumption was 52 million tonnes. The major markets for coal in Canada are electricity generating stations (Alberta, Saskatchewan, Manitoba, Ontario, New Brunswick, Nova Scotia) and the steel industry in southern Ontario. Approximately 11 million tonnes of coal were imported and exports reached a new record of 34.5 million tonnes, mainly from western Canada. Canadian Coal FlowsCanada represents a unique case in the coal world because we both import and export coal (Fig. 1). The reason for this apparent dichotomy is Canada’s geography. Eastern Canadian coal markets are located closer to the eastern United States coal fields and are basically served by them. This is true for both thermal and metallurgical coal. Major imported coal users are the steel industry, electricity generators and other industry including the cement industry in southern Ontario, Quebec, New Brunswick, with a little coal imported into Manitoba. Only about 2.2 million tonnes of western Canadian coal move into the east, including both lignite and bituminous coal."

Jan 1, 1997

By E. A. Davies, Trevor T. Jones

"Aspects of materials, design and operation of suspension equipment is dealt with, hazard, fatigue and special metallurgical properties of certain steels to resist are described, as is the effect of temperature in service modifying the properties of some steels to resist stress concentration and propagation of cracks.The influence of steady impact and fatigue loading and its results are described. Control of manufacture including nondestructive testing is outlined and acceptance parameters and strength calculations are given. Quality requirements and control in manufacture are outlined. A short description of the overwind detaching hook, together with illustrations of the operation of detachment are presented.MaterialsWinding engine ratings of 8000 h .p. and large capacity shafts 2000 m in depth (4000 m depths have already been reached and it may be necessary to go to 6000 m) and up to ten conveyances are not uncommon today. Loads of 100 or even 200 tons hoisted at low speeds are possible within the near future. Some of these appliances are designed to protect lives and installations in hazardous conditions when, due to human or mechanical fault, a malfunction occurs in the system. In addition, such equipment includes suspension gear of various kinds designed to anchor and apply high mechanical tensions to numerous steel ropes installed in shafts necessary either for the safe passage of conveyances or for balancing purposes when heavy loads are in motion.No unique metallurgical problems are presented in underground mining operations, but they have two special characteristics that influence the metallurgical aspects of the de sign of suspension gear and other equipment concerned in the transport of men and materials. (1) Any uncontrolled release of energy caused by the unexpected failure of a component is more likely to injure personnel and cause costly damage to installations in the narrow confines of an underground mine shaft. (2) Some mechanical equipment in mines, tends to be overloaded in service and suffer plastic distortion."

Jan 1, 1987

By Michel Carreau

Presentation topic Introduction to Renewable Power in Remote Mining Industry Trend What are the Challenges and How to address them Acceptability (Management Buy-in) ? RP not core business to mining company Significant upfront costs Project Risks - Technological and Delivery Wind and solar power variability Operating hybrid power (Operator Buy-in) Conclusion Introduction ? RP at Remote Mining Sites Mining Project Cost Energy represents 25% of mining project CAPEX Energy represents 25% of OPEX Diesel, HFO, ? cost : 30+ cents/kWh RP - Proven technology - Excellent track record ?Wind (20 years), Solar PV (10+ years)? Hundreds of GW installed ?Reliable, High availability, very small OPEX. ?Wind/Solar cost : 15 to 22 cents/kWh (with good resource) ?Potential 10% to 20% Reduction in net cost of energy ?Price certainty for 20 to 25 years

May 1, 2013