Search Documents

By J. T. McGrath, R C. A Thruston

The structural changes which take place in polycrystalline copper under the action of alternating cycles of torsion stress were studied, using the optical microscope and the X-ray dif-fraction camera, and an attempt was made to correlate them with changes in the shape of the cyclic stress-strain curve. It was found that the period of work-hardening was less than one per cent of the fatigue life, and that persistent surface marking, which are assumed to be incipient or actual microcracks, occur upon completion of work-hardening. X-ray diffraction patterns revealed considerable grain distortion at the completion of work-hardening in specimens cycled at a high strain amplitude. This distortion became progressively less as the strain amplitude de-creased. Mechanisms for the completion of work-hardening and the formation of microcracks are discussed.

Jan 1, 1962

"The Val d'Or Division now comprises the Lucien C. Beliveau Mine and Concentrator (formerly the Pascalis, described below) and the Chimo Mine. Cambior acquired an initial 50% interest in the Chimo Mine in May 1989 and the remaining 50% in April 1990. Cambior's share of 1989 production was 2121 ounces; the company expects to net 23 750 ounces from Chimo in 1990. Pascalis MineUPDATERenamed the Lucien C. Beliveau Mine at its official inauguration in September 1989, the mine is exceeding forecasts, producing over 11 500 ounces of gold in the first half of 1990. Cambior expects 1990 production to total 34 000 ounces.IntroductionThe Pascalis Mine is located 16 miles east o f Val d'Or, Quebec, and is accessible by a three mile gravel road off highway 117 (Fig. I).The property is wholly owned by Cambior.The Pascalis gold deposit consists o f a sub-vertical diorite dyke 1000 ft long by 30 ft wide containing quartz and tourmaline veins with inclusions of pyrite and native gold . Three vein systems ca n be seen in the deposit , the most important being tensile veins oriented at a right angle to the direction of the dyke and inclined at 40 degrees. These overlapping veins vary in thickness from 4 in. to 40 in. and occur at intervals of six to ten ft. The deposit is, therefore, very difficult to evaluate; a complete evaluation would require drifts over the whole width of the dyke combined with relatively short drill holes (Fig . 2)."

Jan 1, 1990

By A. Cummings

This paper reports two aspects of reactivity of complex Ni-Cu sulphide ores: variations that result from stockpiling of a nickel-copper sulphide ore in the Sudbury area and its consequences on flotation behaviour, especially in terms of metal losses to scavenger tails. In relation to the first aspect, self-heating characteristics of the stockpile were carried out by monitoring the internal temperatures of the stockpile. Six heat sensors were installed with respect to external conditions in local weather during a 7-month period. Stockpile temperatures were mainly influenced by ambient temperature with some retardation effects. The maximum temperature recorded in the stockpile was 44 °C. Samples taken at the beginning and at the end of stockpiling were tested to assess variations in behaviour of the rougher-scavenger flotation. Relative to the fresh ore, nickel and copper losses in flotation of the stockpile fines were 5.0 and 3.6 %, respectively. The fresh ore yields concentrates with higher nickel grades due to differential flotation behaviour of pentlandite and pyrrhotite relative to the stockpile fines, which exhibit a truly bulk flotation behaviour at least during the first 3 stages.

Aug 1, 2013

By D. B. Dreisinger, M. R. Tavakoli

Vanadium has been produced from both primary and secondary sources having various compositions. Vanadium pentoxide and vanadium trioxide are the most available and known sources of vanadium oxides. In this paper, an overview of leaching both oxides has been reported. The problem of vanadium pentoxide leaching under acid conditions is the low solubility of the dissolved vanadium. This was investigated and then supplemented with further studies of leaching at mildly basic pH’s as well as under acid reductive leaching conditions (to form vanadium (IV)). Atmospheric oxidative leaching of vanadium trioxide was investigated using oxygen and ferric ion as the oxidant. It was shown that the leaching of vanadium trioxide using oxygen is very slow; however, ferric ion can dramatically increase the kinetics and leach efficiency.

Jan 1, 2014

By T. T. Wang, T. H. Huang, S. S. Zhan

"Fractures with diverse features dominate the hydraulic behavior of fractured rocks and are one of the major subjects for hydrogeological characterization of a site. This study investigates curve patterns obtained by packed tests, and as well the influence of fracture features based on 59 sets of in situ packer tests with different fracture combinations and fracture features. The result shows that, in the example of Heshe site, neat and tidy fractures usually provide stable channel for water flow during testing, and the hydraulic properties of fractures infilled with breccia and mud may change during testing because of leaching and/or washed out of infilling breccia and mud. Different combinations of fractures with diverse features in packed test sections lead to different curve patterns for in situ hydrogeological tests. For groundwater flowing predominately through neat and tidy fractures, the pressure-discharge curve of modified Lugeon tests are usually linear curve pattern, and the pressure decrease while the discharge increase in pressure-discharge-time curves of single-hole double packer tests, which benefit statistically determining the transmissivity of dominant fracture sets. INTRODUCTIONFractures interlaced in rock masses are major channels for groundwater flow and generally account for the anisotropic and heterogeneous characteristics of permeability for fracture rocks. To describe reasonably the permeability of a fracture rock, the Discrete Fracture Network (DFN) approach and others with similar ideals have been developed. Many methodologies and associate equipment, for instance, the televiewer and the in situ hydrogeological test, have been proposed to investigate the spatial distribution and the transmissivity for different fracture sets, which are two main parameters necessary for the DFN or similar model simulation (Pearson & Money, 1977; Barker & Black, 1983; Hsieh et al., 1985; Bernard et al., 2006; Quinn et al., 2012). However, diverse outlooks for the pressure-discharge curves and the temporal pressure and associate temporal discharge curves often confuse the investigation results by significant deviations on derived permeability (Houlsby, 1976; Zlotnik, 1994; Royle, 2009; Camilo, 2010).Aiming on technical development for in situ hydrogeological tests and fracture investigation, an experimental well site with 10 wells has been established in Heshe in central Taiwan since 2011 (Wang et al., 2011; Song, 2012; Zhan et al., 2013). Extensive geological survey and well-hole scanning by a televiewer provide spatial distributions and outlooks of fractures in detail. Additionally, a series of Lugeon tests, double packer injection tests and pumping tests have been performed to investigate the permeability of fracture rocks, and dominate fracture sets as well. Based on the results obtained from the Heshe site, this study classifies the curve patterns of hydraulic packer tests. The features of fractures involved in packed sections for packer tests are then inspected in detail. Relationship between the curve patterns of hydraulic packer tests and associated features of corresponding fractures in rock are discussed and addressed accordingly."

Jan 1, 2015

By S. Bergquist

In this paper, it is investigated how different types of automation would affect the safety for workers in asphalt paving. The risk for the workers on road construction sites is consistently high in comparison to the average risk of the working population. Automation has been suggested as an alternative for improving the safety in roadside construction assuming that removing workers will inherently eliminate the risk of them being injured. In this paper, the potential for improving the safety using automation is analyzed in detail. By investigating accident statistics and understanding the type of accidents that appear, several different automated functions for increased safety are proposed and described. Based on available statistics, it is possible to estimate the safety benefit, as the reduction in fatalities, for several of the proposed functions. The highest safety benefit would be achieved by automating the road traffic driving through the work zones. This has the potential of reducing the total number of road worker fatalities with over 30 %. In addition, it would decrease the number of road traffic accidents in work zones. Automation of construction machinery and dump-trucks also has the potential to increase the safety.

Aug 1, 2013

By E. Thomson

This type of microscopic investigation, although still in its infancy, has already found practical applications in several different phases of mining activity. The study of the transparent minerals in rocks, by means of the ordinary petrographic microscope, has for long been a very useful supplement to observations in the field, but the opaque minerals, until recently, have had to rest content with a more or less superficial determination with the hand-lens or the blow-pipe. In a great many cases, particularly where the association of metallics has been somewhat complex, this has been entirely inadequate, and the determination of these opaque minerals under the micro- scope, has opened up a new field of scientific investigation that bids fair to surpass, in practical value at least, the micro-scopic determination of the rock-forming minerals. As the details of this kind of microscopy are possibly not entirely familiar to all mining men, it might be well to outline them very briefly before dealing with the practical directions in which this method may be applied. The ordinary petro-graphic microscope, with but one extra attachment, will serve for this work. A small reflecting device, called a vertical illuminator, is inserted immediately above the objective lens. This reflects the light down to the surface of the specimen and from here the light is directed up the middle of the microscope tube to the eye. As it is desirable that the maximum amount of reflection should be secured from the surface of the section, it is first polished and set in a position perpendicular to the vertical axis of the microscope.

Jan 1, 1924

By Hans Lundberg

An electric survey from a 'plane flown over the ground is much faster and cheaper than an electric survey carried out on the ground. The results are obtained as continuous recordings that are resolvable into both a depth expression and a conductivity effect, so that the indications are easier to evaluate, as well as to correlate from one flown line to the other. The prospecting technique adopted in our electric airborne surveys may be brie fly described as follows: A loop of many turns of insulated copper cable is fastened around the fuselage of the 'plane and connected to a generator supplying a few ampere alternating current, usually of a frequency less than 1,000 cycles per second. Just as the current in the primary coil of a common transformer will induce current in the secondary coil when shorted, the alternating magnetic field from this primary current now induces alternating current in electric conductors that happen to be located in the vicinity of the path over which the 'plane is flown. This induced secondary current in each conductive section of the ground causes, in turn, an alternating magnetic field, secondary field, which disturbs or dampens the normal alternating magnetic field from the primary loop flown by the 'plane. These secondary fields are then picked up and recorded by the help of detecting solenoids, amplifiers, and recorders carried in the 'plane. By closer study of such a secondary field it is possible to localize the secondary current causing it and, thereby, the conducting body that contains the secondary current. In the 'plane are continuously recorded, besides the amplitude or intensity of the field, also the phase, which is a measure of how much the recorded secondary field is out of step with the primary field.

Jan 1, 1950

By Malcolm Black

Introduction Before beginning to write this paper, I decided that I should first find suitable definitions of the words Sample and Sampling. The dictionary gives: "Sample.-A portion indicative of the whole"; and according to Baillie (1), sampling is "That process whereby a representative and comparatively small portion of material is selected from a large bulk, and preserved under such conditions as shall prevent contamination or avoidable alteration, with a view to the formation of valid conclusions regarding the suitability of the bulk for specified purposes". These comprehensive definitions are alike in substance, and indicate that unless a truly representative portion is taken, it is not a sample. Ore 'as mined' generally varies a good deal in composition, and, in crushing, segregation takes place. Some of the minerals present, due to differences in hardness and friability, break into smaller pieces than others, and, on reaching the bin, the coarse particles roll away, leaving the fines behind. The result of this segregation is generally quite noticeable on the conveyor feeding the mill, especially when the bin is nearly empty and the crushing plant shut down. Should the sampling period synchronize with either the coarse or the fines, the sample obviously would not be representative. I agree that this is rather far fetched, but I maintain that such a condition is possible. Assuming that a representative sample may be procured from the feed conveyor, the method of cutting it down for assay has considerable influence in maintaining the original condition of the sample. The finer the material is ground after each cut, the more uniform the sample will remain. To illustrate this point, let us take a quantity of fine sand and add, say, three grains of rice to represent metallic particles. We may mix this sample by any of the known methods, then cut it into four equal portions. It is obvious that at least one of the portions will be without a rice grain. But let us grind the three grains of rice into flour and proceed as before. Now there will be a much greater chance of including some of the rice in each portion.

Jan 1, 1935

By Donald F. MacDonald

THE cement plant nearest to Nova Scotia is not far from Montreal. Cement is a heavy product which, because of its relatively low value, cannot stand a high freight charge without unduly enhancing its cost. This is one reason why cement costs are high in Nova Scotia. The regular retail price per bag (8772 lb.) in Antigonish is 85 cents, which would be $3.40 per Canadian barrel of 350 pounds, or $3.65 per American barrel of 376 pounds.It is said that the lowest wholesale price in Halifax is 65 cents per sack, which would be $2.60 per Canadian barrel or about $2.80 per American barrel. According to U.S. Bureau of Mines statistics, the average factory price for cement in 1937 was $1.48 per American barrel, which is practically the same as the value per barrel indicated in Dominion statistics for the Canadian output during that year. The difference between $3.40 and $1.48 is $1.92. It is evident that the average user of cement in the Mari-times pays a stiff premium because Maritime cement raw materials have not been developed. Rock-wool, the manufacture of which is rapidly increasing in Ontario and the United States, is much needed for building insulation in the cold climate of Nova Scotia.

Jan 1, 1939

By W. E. Armstrong

Gypsum was first exploited as ?a commercial proposition in this province by the Union Mining Company which, in 1900 opened quarries on the east shore of Lake Manitoba, near the present site of Gypsumville. This company established a mill at the head of Portage Bay on the lake, and the manufactured plaster was carried by the companies boats to McArthur's siding on the Whitemouth river near Westbourne, Man., from which point it was distributed. In 1904 a reorganization took place and the Manitoba Gypsum Company Limited bought out the original company, and operated the original mill for about one year when it was destroyed by fire. There were many factors which rendered the operation of a mill at the quarries very difficult; lack of rail transportation for bringing in supplies, and the impossibility of local power development made manufacturing costs very high. Satisfactory distribution could not be affected because of water transportation and poor terminal facilities at McArthur's siding. For these reasons the new mill was built at Winnipeg, where cheaper power and better distributing facilities permitted the industry being placed in a better position. The company continued to bring the gypsum rock by steamer to Totogan, from which point it was transported by rail to Winnipeg. This period was one of steady expansion as the product became better known and more universally accepted as a wall finishing material. Unfortunately, in 1909, this new mill was destroyed by fire, causing a serious set-back to the company, at a time when the steady growth of the western market gave every promise of the industry being placed on a profitable basis.

Jan 1, 1925

By Deborah A. McCombe

"One of the cornerstones of NI43-101 Standards of Disclosure for Mineral Projects is the technical report. The purpose of the report is to provide a summary of the scientific and technical information concerning mineral exploration, development, and production activities on a mineral property that is material to an issuer. The reports must be prepared in accordance with NI43101 and Form 43-101F1 Technical Report and the information must be current as of the date of the filing of the technical report. As these reports provide important information to the investing public, qualified persons preparing these reports should, as much as possible, write in plain, simple language that can be easily read and understood by people who are not geoscientists or engineers. So let’s review some of the common deficiencies with technical reports. Non-current technical report Some of the factors you should consider when determining if your previously filed technical report is still current are as follows: •,Is there new technical information on the property, such as drilling, assays, metallurgical testwork? •,Have you made changes to key assumptions, parameters relating to mineral resources or mineral reserves, or economic analysis? If you have completed the previously recommended work, are your recommendations still current? Similarly, are your report recommendations consistent with what you are telling your shareholders or disclosing in the use of proceeds in your offering documents? For example, if the recommendations in the report consist of further exploration and metallurgical test-work prior to completing a preliminary feasibility study and you have completed the proposed work and are now raising money for a final feasibility study, the report is probably not current."

Jan 1, 2003

By V. Gaudreault

Rio Tinto Alcan (RTA) has three smelters that use the Alcoa P155 technology: two in Canada (Grande-Baie and Laterrière, Saguenay, QC) and one in the United States (Sebree, Kentucky). The oldest RTA P155 smelter was built in the 1970s (Sebree) and had an initial current intensity of 155 kA. In the 1990s, RTA installed an amperage booster in Grande-Baie smelter to increase cell productivity. Since then, RTA has continuously pushed the limit of this technology and the target amperage that was 195 kA in 2005 has been increased to 210 kA in 2010.This article describes the successful plant-scale trials to increase current intensity from 195 kA to 210 kA, and the key performance indicator results. It demonstrates RTA's technology leadership to undertake such a development with its Brownfield smelters.

Jan 1, 2011

By A. McLean, Q. R. Yang, Y. D. Yang, G. F. Zhang, P. Wu

A considerable amount of waste slag from the pyrite roasting process is discharged every year. Recovery of iron from the waste slag is of great interest for comprehensive use of mineral resource, reduction of environment impact and improvement of economical benefit to related companies. The objectives of the present work are focused on: (1) Compare various procedures for recovery of iron from the waste slag and select a best procedure for industrial trial which is roasting of the waste slag under reducing condition followed by magnetic separation; (2) Investigate the optimum conditions for maximum recovery of iron from the waste slag. The experimental result shows that under the treatment condition found in this work about 36 to 40% of the iron oxide was recovered from the waste slag, where the iron content in the concentrate is 57%. The total recovery ratio of iron, up to 70%, from the waste slag was achieved. After the treatment, sulphur content in the waste slag was reduced significantly and gangue materials, such as SiO2, Al2O3 and TiO2, were reduced effectively.

Jan 1, 2011

By L. J. Han, Y. J. Zong, S. Y. Wen, J. J. Wei

"Stress strain curves characteristics, deformation and strength properties, and failure process and characteristics of sandstone samples under different stress states were analyzed through triaxial compression tests carried on using TAW-2000 microcomputer control electro-hydraulic servo rock triaxial test system. The experimental results reveal that peak strength, residual strength, elasticity modulus and deformation modulus increase linearly with confining pressure, and failure models transform from fragile failure under low confining pressure to ductility failure under high confining pressure. Macroscopic failure forms of samples under uniaxial compression was split failure paralleling to the axis of samples, while macroscopic failure forms under uniaxial compression was shear failure, the shear failure angle of which decreased linearly with confining pressure. There were significant volume dilatation properties in the loading process of sandstone under different confining pressure, and then based on acoustic emission damage and volumetric dilatation damage the damage evolution properties of samples were analyzed, and damage constitutive model were established, realizing the real-time quantitative evaluation of samples damage state in loading process. INTRODUCTIONDamage is a phenomenon that micro defects in material under monotonic loading or reloading will lead to progressive decrease of the cohesion and damage of volume units. Many scholars at home and abroad have carried out systematic researchers on damage evolution characteristics and constitutive model of rock, and have achieved a series of remarkable results in this field. Lu Y.D. (2004) studied the complete stress-strain curve’s characteristics of marble under triaxial compression, and established the bilinear elastic-linear strain softening-residual ideal plastic damage constitutive model. Ren J.X. (2001) studied the damage evolution laws of coal and rock mass by computerized tomography triaxial loading system, realizing the quantitative evaluation of damage state. Zhang Z.L. (2011) studied the deformation and failure mechanism of strong weathered sandstone by triaxial compression test, and analyzed the damage evolution processes and established the damage evolution equations based on the density method. Li X.J. (2012) studied the microscopic damage characteristics of siltstone under triaxial compression by scanning electron microscope and digital image technology, and analyzed the statistical distribution characteristics of cracks azimuth angle, length, width. Zhou J.W. (2012) studied the strength, deformation and fracture damage characteristics of sandstone by uniaxial cyclic loading and unloading tests, and defined damage variable based on linear damage mechanics theory and acoustic emission (AE). Cao W.G. (2006) established a new damage model and a statistical damage constitutive model of rock under specific confining pressure according to the force of damaged part and undamaged part in rock on the base of statistical damage theory. Li S.C. (2014) studied the damage evolution characteristics in the whole uniaxial compression process of sandstone by electrical resistivity and AE, and proposed a status qualitative criterion for rock damage."

Jan 1, 2015

By R. Lodha, C. Oprea, G. Oprea, H. Zargar, T. Troczynski

"The basic refractories used in non-ferrous industry contain chrome ore for improving the thermal shock resistance, thus reducing the penetration of molten metal and fayalite-type slags into the lining. The current study aims to replace chrome ore with Me4+ ions along with Fe3+ ions in order to form MgO-Al2O3- FeOx-Me4+O2 based complex spinel systems that could perform similar to the complex chromia-bearing spinel in the magnesia-chrome refractories. This system allows for lower temperatures of synthesis and sintering. In our study, compositions with 60% MgO were fired below 1500°C and resulted in complete formation of complex spinel, and open porosity less than 5%. The in-situ formation of the complex spinel from the fine mix of oxides in the MgO-Al2O3-FeOx-Me4+O2 system offers a suitable alternative of binding system to produce basic refractories at lower temperatures and of similar physical and mechanical properties with magnesia-chrome bricks fired above 1750ºC. INTRODUCTIONThe synthesis of magnesium aluminate spinel (MgAl2O4) (Maschio, Fabbri, & Fiori, 1988) or magnesium chromate spinel (MgCr2O4) from their respective oxides is diffusion controlled resulting in a sluggish reaction even at high temperatures. For instance, the diffusion of Mg2+ and Al3+ ions in the intermediate spinel layer during reaction is slower than the diffusion of Mg2+ in corundum and Al3+ in periclase. The interfacial layer of spinel formed during the reaction increases the diffusion path for the spinel forming cations. This accompanied by ~8% volume expansion retards further reaction resulting in incomplete spinel forming reaction during sintering and hence densification during the reaction cannot be achieved. In order to assess sintering studies with fine particulate oxides that would result in a lower diffusion path, a mechanical mixture of the hydroxides of aluminium and magnesium calcined at 1400ºC to 1600ºC for 1 hour does not result in complete spinel formation (Sarkar, Das, & Banerjee, 2003), which indicates that reaction sintering of stoichiometric magnesium aluminate spinel is retarded by initial reaction forming the interfacial spinel layer. The basic bricks used as linings in non-ferrous pyro-metallurgical convertors are manufactured using magnesia and chrome ore, the sintering of which produce spinel solid solution. This solid solution is a mix of both normal and inverse spinel structures that sinters at temperatures in excess of 1800ºC in air."

Jan 1, 2012

By Chr. Krause

Within the scope the collaborative research centre 599 (Medical University of Hanover, University of Veterinary Medicine Hanover, University of Hanover) the behaviour of the degradation of magnesium materials as implants are investigated by using animal experiments (rabbits). Thus extruded cylindrical pins from the magnesium alloys MgCa0.8%, WE43 and LAE 442 were implanted intramedullary in the tibiadiaphyses. The implantation duration was 3 and 6 month. After the explantation 3 point bending tests were carried out to investigate the possible changes of the mechanical properties. Clearly changes in dependence of the implantation duration could be determined. The three magnesium alloys show a decrease of the mechanical resistance with an increasing implantation time. To evaluate the degradation process, wich is the reason for the changes, micrographs and element analyses (EDX) have been accomplished after the 3 point bending tests. The micrographs show for all used magnesium alloys corroded surfaces but no preferred corrosion on the grain boundarys. The element analyses show beside a layer which is rich in calcium and phosphorus an agglomeration of rare earth elements in this layer. With these results a using of magnesium alloys as a material for implants can be announced.

Jan 1, 2006

By Jozef S. Stachula

"INCO Limited operates eleven under-ground mines in the Sudbury area. The mines are located on the rim of the Sudbury Basin, an oval with the axis in the range of 27 km and 60 km. The ore dips to at least 3000 m below surface. The ores are mined primarily for nickel and copper. Total ore production from underground is in excess of 55 000tonnes per day.Over 40 surface fans have been installed since the late 1960s. All of the fans are adjustable pitch, axial flow units. A major factor influencing ventilation design in the last 30years has been the introduction of diesel equipment underground. Volumes per fan have ranged from 60 m3/sec. to 330 m3/sec., with motors from 100 hp to 2500 hp.Fans of the axial flow type have been commonly used for main fan installations at Canadian mines for many years. The standard arrangement has been to mount these fans horizontally, i.e. with the fan shaft and the long axis of the housing horizontal. This is a natural arrangement for an underground fan, but for a surface installation, a vertically mounted fan has definite advantages.The surface area taken up by a typical vertical fan installation is generally about one quarter that of a horizontal fan of the same capacity (Rutherford, 1957). This is not a problem with isolated fans and fat surface out crop sites, but where the installation is to be near existing buildings, or where there are poor surface soil conditions, space and cost considerations greatly flavour vertical fans."

Jan 1, 1996

By O. Lundhede

Today, systems and machinery usually are designed to meet only one specific customer?s requirements. One reason for this is that underground automation and smart functions are often developed tightly together with a customer. This is natural, since risk and cost can be shared between the customer and the supplier. Nevertheless, when the automation product develops and the market increase this will cause problems: The highly specialized products will not fulfill the next customer?s demands. In order to cope with this problem, Atlas Copco works towards a common platform. Instead of designing solutions for specific customers, we will lift the abstraction and focus on standardized modules. These modules, or function blocks, can then be combined in a large variety of configurations. The benefits of combining modules into products are, for example: increased flexibility when options are available for many machines; easier commissioning and maintenance since less different spare parts and tools are needed; and easier operation since the user interfaces have a similar look and feel. This paper will present the ongoing work towards standardized modules. We will discuss how our Rig Control System (RCS) allows for modular design at Atlas Copco. RCS has number of standardized modules that are used in different surface and underground mining and tunneling equipment. These modules are also used for optional products such as, drilling, radio-remote control, and telematics systems.

Aug 1, 2013

By Richard E. Barrett

SOME YEARS AGO I was associated with a mining operation which, because of its isolated location, burned wood for heating purposes. Year after year the tractors and tucks hauled the cordwood in from the edge of the ever-growing clearing. Each year the cartage costs became greater. The degree to which transportation distances affect the economics of fuels obviously varies with many factors, but the main criterion is the amount of heat a unit weight of the fuel will produce. For in-stance, wood is limited in most cases to a haulage distance of a few miles. Coal can be shipped hundreds of miles, whereas petroleum and gas ?can be transported thousands of miles. The world is now on the brink of having a new fuel -uranium. It has the virtue of being so concentrated that transportation costs can, for all practical purposes, be disregarded.

Jan 1, 1958