Search Documents

By T. E. Morimoto

Summary The Research Council of Alberta has made a series of tests with the cyclone washer to investigate the influence of the following operating variables: underflow apex diameter, .specific gravity of medium, pulp ratio, density distribution of the feed, and size analysis of the feed. The results obtained for all the variables studied, except size analysis of the feed, are included in this paper. The tests were made with smaller underflow apex diameters and lower specific gravity .suspensions than have been recommended by Cerchar for the sharpest separations. However, what is considered to be sufficiently good cleaning was accomplished with a suspension of 1.30 specific gravity and an underflow to overflow diameter ratio of 0.56. It was found that the sharpness of separation was not affected appreciably by variations in specific gravity of suspension or underflow apex diameter provided that the density of separation was within the normal range of washery operation. Cyclone performance was not too adversely affected by decreasing the pulp ratio. The minimum figure which gave reasonable separation was 4 to 1. The tests with various density distributions of feed revealed .that the degree of washing difficulty had no detrimental effect on the .sharpness of separation given by the cyclone. Introduction A major problem of the bituminous coal industry today is that of reducing the ash content of the finer sizes (minus 1/4-inch) of coal. This problem is particularly acute in Alberta, where, because of tectonic movement subsequent to deposition, the coals have been rendered friable, and bands of impurities have been intimately mixed with the clean material. As a consequence, most Alberta coals, as mined, contain a large proportion of fines and have a high inherent mineral-matter content. The advent of mechanized mining and stripping operations ?has further aggravated this problem.

Jan 1, 1952

By R. L. Bruening, L. Navarro, R. M. Izatt, N. E. Izatt, S. R. Izatt

Green chemistry principles will be discussed, and examples will be given of the use of Molecular Recognition Technology (MRT) to selectively separate valuable metals such as rhenium and palladium from various copper refinery feed streams. Recovery of these metals has numerous advantages including (i) conservation of valuable resources, (ii) prevention of environmental damage, and (iii) elimination of capital and operating expenses due to re-processing or disposal of metal-bearing streams. INTRODUCTION Refining of copper ores has a long and successful story. The history of copper, one of the first metals mined in human history, illustrates the global challenges faced as a result of increased demand for major metals and for by-product specialty metals found with them in trace amounts (Izatt et al., 2014). Copper has valuable properties, which have sustained its use over the centuries. It is an ideal material for creation of novel materials. Some desirable properties of copper that have proved valuable in our high-technology society include suitability for alloying with many other metals; ease of joining by soldering and brazing; good combination of mechanical qualities; high resistance to corrosion; suitability for many artistic purposes; and, of great importance in the modern era, efficient and economic use as a conductor of electricity. Copper mining in the U.S.A. began in the late nineteenth century in Montana (Izatt et al., 2014). The estimated total amount of copper mined globally before 1800 is about 5 million tons, four times less than is mined in a single year today (Flanagan, 2018). Production of copper in the U.S.A. has remained fairly constant at about 1,300,000 to 1,400,000 metric tons per annum from 2013 to 2017. Specialty metals such as bismuth, rhenium, molybdenum, and others that have become essential in our 21st century technology, and precious metals such as silver, gold, and the platinum group metals (PGMs) are concentrated by geochemical processes in trace amounts in copper ores. These specialty and precious metals were discarded into tailings in early mining operations, since limited extractive technologies existed and uses for most of them were limited. Thus, economic benefits for recovering them were limited, primarily, to silver and gold. Today, copper processing is the main, and often the only, commercial source for certain of these elements (Izatt et al., 2014). For example, molybdenite (MoS2) is the predominant ore mineral of molybdenum mining (Pohl, 2011). Cu-Mo-Au porphyry ore deposits supply ~75% of the world’s copper, 50% of the molybdenum, nearly all of the rhenium, and 20% of the gold. Typical ore grades are 0.5–1.5% copper, 0.01–0.04% molybdenum, and <1.5 g/ton gold. Molybdenite is the primary source for rhenium, among the rarest of metals, which is an essential component of super alloys, such as turbine blades in the aerospace industry (Pohl, 2011). Most rhenium is obtained as a by-product of molybdenite from copper mines in Chile. The case of rhenium raises an important issue. Continued availability of rhenium, selectively concentrated in copper ores, depends on continued mining and processing of copper. Since the mining company’s main interest is typically in copper production, continued recovery of rhenium and other specialty elements present in the ore body is at risk. Dependence of specialty metal supply on continued mining of major metals exists in several additional cases including indium, gallium, selenium, tellurium, germanium and bismuth (Pohl, 2011). PGMs, on the other hand, are typically mined for their own value, which far exceeds that of associated base metals. However, copper ores often contain marketable amounts of platinum and palladium, making their separation of interest, if this can be done economically.

Jan 1, 2019

By Floyd Smith

Based on underground observations made in .the coal mines of the Dominion Coal Company Ltd., this paper deals with the stress phenomena in the approach roads and headways and in the gob areas associated with the longwall method of total extraction. The deformation of roadways during development and the deformation of roadways during the total extraction period is delineated and presented in graphical form .. Conclusions are made as to the feasibility of the introduction of the retreat method of longwall extraction in one of the colhenes. The importance of future studies are enumerated, especially. those pertaining to the determination .of the opti.m.um sizes of protective pillars and to increasing the efficiency of the current methods of artificial roadway support.

Jan 1, 1967

By M. I. Kalashnikova, Y. M. Shneerson, M. V. Keskinova

Interaction between mattes having various compositions and solutions with a wide range of free acid and non-ferrous metals concentration have been studied in terms of chemistry, mechanism and kinetics. The solution acidity and oxidizers to reducers ratio in the matte-solution-gas phase system have been demonstrated to be the major factors determining the process behaviour. It was found that the types of copper and nickel secondary sulphides resulted from nonferrous metals precipitation from solution, depend on of the solution and initial matte composition. Based on these studies, technologies of matte leaching and nonferrous metal precipitation in the form of rich sulphide concentrates are developed.

Jan 1, 2004

By G. Lodewijks

This paper explores the savings that can be achieved in the energy consumption of belt conveyors used in mines by changing the conveyor components, the operational parameters of the system or the belt properties. First the concept of energy savings is introduced by looking at the energy consumption of belt conveyors from a theoretical point of view. Also methods for the calculation of the power consumption of a belt conveyor and the associated emissions are presented. Two case studies are presented in which the effects of the change of the operational parameters of the system, in this case the belt speed, and the belt properties, in this case the application of aramid products in the belt, are presented.

Aug 1, 2013

By W. Leblanc, J. Phalen

This paper tells the story of a serious mine fire on a mechanized longwall face in a submarine coal mine at Glace Bay, Nova Scotia. The story gives, in chronological order, a technical account of the steps taken to investigate, fight and contain the fire. The time during which the events took place spans from June 19 to November 7, 1975.

Jan 1, 1976

By Xueyi Guo

The total production of nonferrous metals in China is 31.35 million tons in 2010, which ranks first in the world for the past ten years. Large quantities of solid wastes including slag, residue, ash, and dust are produced every year in the production of nonferrous metals. These secondary resources are renewable, not only contain abundant valuable metals which can be recycled by metallurgical processing, but also could eliminate the pollution to the environment. In this paper, the status quo of the main nonferrous metals recycling in metallurgical industries in China was summarized, and the future development of waste processing and resource recycling was prospected.

Jan 1, 2011

By L. P. Chrismas

"IN 1975, Nova Scotia produced 1.8 million tons of coal with a FOB mine value of $47.6 million. Of this total, about 30 per cent or 600,000 tons was coking coal and the remainder was steam and industrial-grade coal. The Nova Scotia Power Corporation consumed 630,000 tons in three generating stations and 570,000 tons were sold to Sydney Steel for making coke for its steel operations. Exports, principally to Great Britain, comprised 370,000 tons in 1975 in addition to the 300,- 000 tons shipped to other provinces for use by cement and pulp and paper companies. In 1975, just over 100,000 tons of coking coal were imported into the province from Alberta. Before 1975, low-volatile coking coal was traditionally obtained from the United States. In 1975, production came from seven individual mines and one project involving reclamation from mine dumps in Pictou County. Of the seven producers, four are owned by the Cape Breton Development Corporation, a federal Crown corporation; the remaining three are small independent mines, but, even though small, they are sizeable contributors to the economies of their local areas. After 101 years of continuous operation, Devco's Princess mine was closed in 1975. The Nova Scotia coal industry, in terms of value, accounted for about half of total mineral production in 1975. The industry provides jobs for 3,000 men and women. It is also significant that in 1975 Nova Scotia produced about 6.5 per cent of Canada's total coal production of 28.3 million tons. Detailed statistics on Nova Scotia's coal industry appear in the Appendix."

Jan 1, 1976

By Hamidreza Soltanzadeh

The injection of CO2 into a reservoir or aquifer can potentially result in deformation, induced fracturing and fault reactivation in the injection zone and/or the rocks that surround it. This paper reviews the data collection and geomechanical analyses performed to assess these potential hazards for the Heartland Area Redwater Project (HARP), in which CO2 sequestration is being considered in a carbonate (Leduc Formation) reef. A three-dimensional mechanical earth model (3D MEM) was developed using available geophysical log data from several wells. The geomechanical response to CO2 injection was studied using a finite element numerical model based on the 3D MEM and pore pressure distributions predicted using a reservoir simulator. The modeling results suggest that the potential for induced fracturing and fault reactivation is low and the maximum predicted ground surface heave is less than 2 cm. Sensitivity analyses conducted with a 2D geomechanical model that was extracted from the 3D model confirm that this conclusion holds true even when a reasonable measure of uncertainty in rock mechanical properties, ambient pore pressures and horizontal stress magnitudes is accounted for.

Jun 1, 2012

By M. W. Bates, A. L. Mular

This paper, based on work carried out at Queen's University, describes the development and use of mathematical models of the parallel cyclone classifiers being used in the Strathcona mill of Falconbridge Nickel Min.es Ltd.

Jan 1, 1971

By E. O. Magnusson

THE orebodies of the Preston East Dome mine show a considerable variation in size,? shape, dip, and ground condition. They vary from small and large irregular masses being mined by shrinkage, cut-and-fill, and square set-and-fill mining methods to narrow veins being mined by open stoping. Standardization of mining operations has necessarily been difficult. This considerable variation in mining condition prompted the development of a bonus system which would give more equitable bonus payments through-out the mine than those obtained by the usually accepted methods of calculating mine bonus. PRINCIPLES ON WHICH THE SYSTEM IS BASED Under an incentive bonus system, performance (efficiency) and a price per unit of work done are inter-related. It is in the application of this? principle to working conditions .in the Preston East Dome mine that the system to be described differs from the standard methods of calculating mine bonus. It was found that the method of paying a fixed price per unit of work done, under the &apos;contract&apos; system, gave satisfactory results in development, less satisfactory results in timbering, and results which were not satisfactory in stoping. Under the fixed price system, bonus payments, in timbering and stoping particularly, were very erratic and did not necessarily represent fair payment for the work done. A fixed price in development is satisfactory because the work done, and the conditions under which the work is done, are uniform. The drilling and blasting cycle is completed in one shift, the size of heading is con-trolled, and a minimum number of holes are required in order to obtain a satisfactory break. The performance possible under these conditions has been found to be confined to a fairly narrow range. By performance in development is meant the efficiency of the working crew as expressed in terms of the two variables of feet of advance per round and pounds of ex-plosives consumed per foot of advance. A change in rock formation, how-ever, may alter to a marked degree the performance possible, quite independent of the skill and energy of the working crew. The changes in working conditions that affect development performance from the standpoint of bonus calculation are usually easily apparent and are satisfactorily met by establishing several fixed prices.

Jan 1, 1944

By Theophile Yameogo

The rock mechanics literature has documented the challenges, failures and successes of tunneling through weak rocks. Cases usually deal with low RMR rock masses or high stresses in a fractured zone. With the combination of 5MPa water pressure, 14 RMR ground with clay infillings and ground freeze walls, the case of the 510-8225N development drift at McArthur River is certainly much more challenging, especially when high grade uranium production is at stake. The article explains the excavation and the ground control techniques that were used to overcome the challenges of development at the Unconformity in the Athabasca Basin.

Aug 1, 2010

By J. A. Vezina

The effects of particle size distribution on metal extraction have been determined from pressure leaching Renzy Mines Limited concentrate with oxygen. Using a pulp density of 30 per cent solids, an oxygen pressure of 80 psig, a temperature of 230°F, a grind of 2.5 hours and a retention of 8 hours resulted in the almost complete dissolution of the nickel and the cobalt and the decomposition of over 96 per cent of the chalcopyrite finer than 20 microns. Only 11 per cent of the chalcopyrite coarser than 20 microns was reduced to smaller than 20 microns.

Jan 1, 1973

By L. Vinnett, I. Panire, J. Yianatos, F. Ruiz

"The effect of operating variables on the flotation performance at steady-state has been extensively used for modelling and simulation of separation processes. However, the dynamic characterization of key variables such as gas dispersion (Sauter mean diameter of bubbles, D32, and bubble surface area flux, SB) and froth discharge rate is rather scarce. In this paper, an experimental design allowed identifying the dynamic response of the flotation process in a laboratory scale flotation cell, using a two-phase system, airwater. The installation included automatic control for the superficial gas rate, JG, and the pulp level. Gas dispersion was evaluated in terms of the Sauter mean diameter of a bubble population and the bubble surface area flux, SB = 6·JG/D32. The D32 was measured using the McGill Bubble Size Analyzer (MBSA) along with a semiautomated algorithm. In addition, the froth discharge velocity was measured in real-time using a Visiofroth system. The control variables were the superficial gas rate and the frother concentration (Teefroth). The dynamic characterization of the flotation process is useful to design algorithms that allow the direct or indirect control of metallurgical variables such as flotation rate, concentrate grade and mineral recovery.INTRODUCTIONGas dispersion indicates the way the gas entering a flotation machine is dispersed throughout the volume of the equipment (Schwarz & Alexander, 2006). The gas dispersion is typically characterized in terms of the bubble size (dB), gas holdup (eG), superficial gas rate (JG), and bubble surface area flux (SB =6·JG/dB) (Finch et al., 2000). All these variables have significant impact on the metallurgical performance of flotation machines. For example, Perez-Garibay et al. (2014) investigated the effect of the particle size, bubble size distribution, superficial gas rate and collector dosage on the flotation performance, for the separation of a sphalerite mineral. The authors observed that recovery increased with the superficial gas rate ranging from JG = 0.04 to JG = 0.08 cm/s and also a maximum recovery was obtained for bubble size close to 300 µm. Gorain et al. (1998) reported a strong correlation between the flotation rate constant and the bubble surface area flux in a zinc cleaner circuit. Both variables were directly proportional at three froth depths in the range of hF =7 - 45 cm. Dobby & Finch (1986) incorporated the effect of the superficial gas rate and the bubble size on the flotation efficiency by means of a kinetic model for the rate constants. Yianatos & Contreras (2010) developed a model to estimate the carrying capacity in large flotation cells by including the bubble surface area flux."

Jan 1, 2016

By Paul L. Broughton

"IntroductionThe coal deposits, all of lignite rank, of economic interest in Saskatchewan are associated with the Ravenscrag Formation (Paleocene). Several Cretaceous formations have less significant lignite accumulations (Broughton, Irvine and W'hitaker, 1974). The Swan River Group (lower Cretaceous) and Judith River Formation (upper Cretaceous) have the only coalbearing strata in the shallow subsurface of central Saskatchewan. The Swan River Group coalfield is relatively small and underlies only 15 sq km of the surface approximately 40 km south of La Ronge, Saskatchewan. An estimated 36 billion short tons are within 45 m of the surface. No reserve estimates are known to have been calculated for the coal-bearing Judith River Formation exposed at the surface in the vicinity of the South Saskatchewan River valley in west-central Saskatchewan. Although no coalfields have been delineated, lignite beds up to 1.8 m thick have been intersected in test holes. The coal-bearing upper Cretaceous and lower Tertiary strata of the northern Williston Basin extends the full width of southern Saskatchewan for 650 km, and from the United States border 120 km north to 50° latitude (Fig. 1). Only the coalfields of the Ravenscrag Formation, because of their economic interest, will be considered further. There are four major coalfields. They are, from east to west: Estevan, Willow Bunch, Wood Mountain and Shaunavon (Cypress) coalfields. Cumulative lignite seam thickness for each basin is 10 -15 m (Figs. 2 and 3). The origin of each coal basin, resource calculations, seam stratigraphy, and mining activity are discussed. Regional Setting The Williston Basin is an ellipsoidal depression in the Precambrian basement, centered in western North Dakota and marginal to the exposed craton of northern Saskatchewan and central Manitoba (Fig. 1). The sediments of the basin range from Cambrian to Pleistocene in age and have a maximum known thickness of 4614 min western North Dakota. A maximum of 3200 m is recorded in southern Saskatchewan. Most structural deformation is late Cretaceous to early Tertiary (Paleocene) in age, coinciding with the Laramide Orogeny. The pre-Laramide Williston Basin, with a depocenter near Williston, North Dakota, began developing during the middle Ordovician, or possibly earlier."

Jan 1, 1985

By Barry J. Morash

The over-all slope angle of between 55 and 60 degrees at the Adams Mine necessitates control blasting on the final pit walls. The control blasting techniques used are pre-shearing and buffer blasting. Pre-shearing with 2&apos;I2-inch holes on 5-foot centers is used in areas where jointing and rock type are not conducive to smooth stable walls. Buffer blasting with 12&apos;/4-inch holes is used in areas where the rock is competent. Control blasting adds to the operating costs, but can result in substantial savings in increased slope angle and reduced stripping.

Jan 1, 1978

By L. O. Cooper

IN THE operation of most mines, hoisting ropes, made of steel, play a very important part in the conveying of men and material between surface and the underground workings. It is obvious that, in order to maintain a maximum degree of safety, certain restrictions must be placed on the loads that may be carried by hoisting ropes, as well as on other factors that may affect the life of the rope. It is the purpose of this paper to suggest ?a new method of defining the necessary restrictions. The three main stresses in a hoisting rope are the static stress, bending stress, and dynamic stress. Crushing stresses, which are also present, are largely indeterminate and may best be allowed for by proper grooving of drum and sheaves, by adequate inspection of cross-over points, and by limiting the number of layers on the drum. They will, therefore, not be considered in this analysis. In the ?recent Ontario regulations, the limiting conditions for the main stresses are specified separately. The static stress is limited by setting a minimum static safety factor of 5.0 The dynamic stresses are allowed for by specifying a minimum capacity factor of 8.5, which has the effect of increasing the safety factor required at smaller depths in a uniform manner. The bending stresses are limited by calling for a drum-dia./rope-dia. ratio of at least 60 for ropes up to 1 inch in diameter and 80 for ropes greater than 1 inch in diameter. One disadvantage of this method is that the controls are too rigid and do not allow the operator sufficient freedom of action within safe limits.

Jan 1, 1951

By Phil Keele

"Manalta Coal Ltd. 's Vesta Mine will supply Alberta Power Limited's 740 MW Battle River Generating Station with 1 128 000 tonnes of sub-bituminous ""C"" coal in 1983. Mana/ta Coal Ltd. and Alberta Power Limited are in their seventh year of a 31-year coal supply agreement. With the exception of localized topographic highs where three coal seams are mined, the Vesta Mine is primarily a single-seam mining operation. Vesta's comprehensive programs of mine planning, preventative maintenance, reclamation, and employee relations make it an efficient and a well run operation. Introduction The Vesta Mine, located in east-central Alberta approximately 300 km northeast of Calgary, supplies sub-bituminous ""C"" coal to Alberta Power Limited's 740 MW Battle River Generating Station. The coal reserves and principal stripping equipment are owned by Alberta Power Limited. Manalta Coal Ltd. owns and operates the additional mining equipment and support facilities. Coal production is from a single pit, 3.5 km in length. Both single and multi-seam operations are encountered in the active pit. In 1983, production is anticipated to increase to I 128 000 tonnes from 906 000 tonnes in 1982. The additional tonnage will be achieved by operating 24 hours per day, 5 days per week. The following sections briefly highlight historical, geological and mining/reclamation aspects of the Vesta Mine. Figure I illustrates the location of the Vesta Mine in relation to the cities of Calgary and Edmonton. History Coal mining for domestic use began near the turn of the century in the Vesta Mine area. Initially, small underground room-and-pillar operations were dominant. As equipment technology advanced, surface strip mining replaced the underground methods."

Jan 1, 1985

By T. P. Riordon

"Major swings in the silver price since 1979, along with the ever constant fight to maintain ore reserves has forced United Keno Hill Mines Limited through several unique series of events in order to survive in the 80s.This paper is specifically meant to be a description of safety and productivity improvements achieved to ensure the survival of a silver mining community ill the Yukon. There are, however, other events and conditions that must be described to complete the story and this paper attempts to do that as well IntroductionUnited Keno Hill Mines Limited, a subsidiary of Falconbridge Limited, is the only silver producer in the Yukon. Operations are located in north central Yukon, in and around the small town of Elsa, latitude 62.5 °, about 275 road miles from Whitehorse. The Arctic Circle is about 185 miles due north of the town.Temperatures in 1986 ranged from a high of 28.5°C in July to a low of -37.0°C in November, however, much lower temperatures have been recorded in previous years. Due to the mountainous terrain the town of Elsa is completely in the shade from mid-November until early February, a period of about 12 weeks.The Elsa area, as is most of the north, is considered semiarid with an average precipitation level of about 15 inches. Vegetation, however, is quite abundant though slightly dwarfed at the townsite elevation of 3200 feet above sea level: Many of our operating and exploration portals as well as our open pits are above the tree line. Permafrost in the area has been recorded up to 400 feet below the surface."

Jan 1, 1988

By M. E. Sirkka

"INTRODUCTIONInco Ltd. has ten operating mines in the Sudbury district. Over the last ten years mining methods have changed at Inco with special emphasis on the introduction of bulk mining replacing conventional mechanized cut-and-f ill and undercut-and-fill methods. At the same time, the technology and size of LH D equipment has also progressed to meet the demands of bulk mining. This paper will concentrate on various aspects of the introduction and operation of electric LHD equipment a t Inco Limited, Ontario Division. BackgroundInco Limited received its first electric 2 cu. yd capacity LHD in July 1975 at Creighton Mine. The unit was tested pulling shrinkage stope muck and then was moved to a mechanized cut and- fill complex on 6600 Level. The electric scooptram received quick acceptance from the operators, due to its quiet operation and low heat generation, in a relatively hot operating environment. Although there are only two of these units operating a t present, this initial favourable experience, both in cost and efficiency, led to the development and purchase of electric scooptrams of the 5 cu. yd size. There are currently eleven 5 cu . yd electric LHDs in operation.The most recent development a t Inco is the move to yet larger electric LHDs in the 8 cu. yd size. The first electric ""Eight"" has now been in operation at Copper Cliff South Mine for over a year. This unit has the distinction of being the first one of its kind in service in North America. At the time of writing, there were ten 8 cu. yd electric ma chines operating in Inco&apos;s Ontario Division Mines, with three on order."

Jan 1, 1989