Search Documents

By C. Fleming, J. R. Goode

ABSTRACT: Data were produced from two uranium project studies that were conducted in 2008, both involving uranium recovery from leached slurry by resin-in-pulp (RIP) with strong base resins. In both studies, excellent metallurgical results were produced. The loaded resins were eluted with strong sulphuric acid and recycled through RIP circuits in an integrated process. Resin losses by either abrasion or mechanical breakage were immeasurably low. Metallurgical results from these two campaigns are presented, along with a case study economic analysis of RIP versus the alternative processes of counter-current-decantation or filtration and solvent extraction.

Jan 1, 2011

?Bank Lending to the Mining Sector affected by 2 broad factors since Mid 2008: 1. Economic Downturn (?the Real Economy?) for mining companies directly reflected in lower metal prices (current and forecasted). In the case of gold companies, minimal effect. 2. Financial Crisis (?the Credit Crunch?) as it has affected the lending activities of those banks active in the mining sector.

May 1, 2009

By Denni Hoffmann

"Banded iron formation rocks associated with massive sulfide lenses in the Broken Hill Pb-Zn-Cu-Ag deposit in the Namaqualand Metamorphic Complex, South Africa, were investigated with respect to the geochemistry of manganiferous silicate-rich bands. Two common varieties of these are: amphibole- and garnet-rich iron formation bands. The results reveal that the former are enriched in Fe, Mg, Cu, Co and S. The garnet-rich bands are enriched in Mn, Ca, P, Pb and Ba with significant detrital contamination of Ti, AI, Zr, Cr, Y, V, Ni and Nd.The silicate-rich bands have compositions, in terms of, Si/AI, SilFe, FelMn, LalCe and Co/Zn, comparable to submarine chemical sediments which precipitated from hydrothermal fluids. The garnetand amphibole-rich bands are interpreted as ""evolved"" and ""immature"" hydrothermal sediments, respectively. The latter resulted from rapid precipitation after exhalation, whereas the former had a longer residence within sea water. The silicate-rich bands both exhibit increasing Mn/(Mn+Fe) fractions, which are consistent with a variation expected from proximal to distal depositional settings. The prevalence of garnet-rich bands over amphibole-rich bands is interpreted as the result of injection of hydrothermal fluids from a single vent situated along the northwest margin of the Broken Hill deposit."

Jan 1, 1994

By S. Dessureault, M. Yildirim

More mining companies are now investing in IT, including updating one of the traditional IT process control tools used in the mining industry: real time in-pit truck allocation control and monitoring systems, or fleet management systems (FMS). These systems have been used to maximize the overall mine production by improving equipment utilization and reducing production costs. Most modern operations monitor the in-pit operations using GPS and wireless communications to produce data. Improvements in bandwidth, sensors, and computing power are causing modern systems to become more complex and generate more data. However, human analysis by simple regression or table generation in spreadsheets of the data is becoming impossible. Data mining solves this data management problem. Data mining finds patterns and relationships in very large data sets. This paper describes the application of modern data mining techniques on truck dispatching systems in a real open pit hard-rock copper mine. The analyses conducted included determining how the trucks performed under particular conditions and allocation systems. The long-term benefits of this work are to identify strengths and improvement opportunities in truck assignment systems and establish the skill sets and IT infrastructure needed in undertaking more complex datadriven technology such as a truck dispatcher trainer.

Jan 1, 2007

By F. Chevarin

The reaction of O2 with the carbon anode is considered as the main parasitic chemical reaction affecting Hall-Heroult process anodes. The current study aims at investigating the influence of the microstructure of baked anode on its overconsumption. Samples were removed from different positions of an industrial anode. Density, porosity, Lc and BET specific surface area were measured. The anode reactivity was evaluated based on the weight losses for the samples resulting from the reaction of anode with air at 550°C after 7h. The essential parameters determined to control the air reactivity are closed porosity, Lc and pores with a pore entrance radius of 1.5, 8.5 and 12 p.m. The knowledge of effects of these parameters allows better understanding of the reactivity of anodes and consequently reduction of their overconsumption in electrolysis bath.

Jan 1, 2011

By Wei Huang, Anh V. Nguyen

"Potash flotation is an industrially proven success of flotation of soluble salts, but its collector adsorption mechanism remains elusive. In this paper, specific ion effects in NaCl-KCl flotation with carboxylate collectors were investigated. Flotation recovery and contact angle were determined as a function of brine composition of NaCl and KCl. The experimental results have shown that wettability of KCl and flotation of the soluble salts with laurate collectors were dependent on brine ion composition. Specifically, adding Na+ to brines decreased hydrophobicity of KCl crystals and their flotation recovery. Both KCl and NaCl could be floated with laurate collectors. However, flotation of NaCl was greatly enhanced by adding K+ to brine whereas flotation of KCl was significantly suppressed by the presence of Na ions. The decrease in KCl recovery upon adding Na+ is attributed to the counter-ion binding in the pulp. The flotation recovery enhancement of NaCl in the presence of K+ is explained by two effects: 1) increasing K+ concentration leads to a better dispersion of collector colloids in the pulp and 2) K+ enhances the collector adsorption at NaCl crystal surfaces. The water affinity matching rule can explain the specific ion binding behaviors and supported by the SFG spectroscopic results.INTRODUCTIONPotassium is an important fertilizer. Its primary source comes from potash ores, which are a mixture of sylvite (KCl), halite (NaCl) and many other complex double salts such as carnallite (KCl·MgCl·6H2O), alkali nitrates such as KNO3 and NaNO3, and sulfates-langbeinite (2MgSO4·K2SO4) with water-insoluble minerals such as clay and carbonate minerals. Previously, these salts were recovered with a lengthy hot leaching method, with further crystallization of potassium salts from saturated saline solutions. Selective flotation has been preferred since 1940s. Various collector adsorption mechanisms have been proposed soon after the industrial introduction of potash flotation. These include the formation of the insoluble compound model (Halbich, 1933; Singewald, 1961), an ion exchange model (Fuerstenau and Fuerstenau, 1956), a heat of solution model (Rogers, 1957), the surface hydration model (Schubert, 1988), the surface charge model (Roman, 1966; Miller et al., 1992), the interfacial water structure model (Hancer and Miller, 2000) and the colloid adsorption model (Leja, 1983; Burdukova and Laskowski, 2009). Most of the early exercises attempting to propose a unified rule on collector adsorption mechanisms can be seen as heroic endeavors due to the consideration of a vast number of salts in the pulp including alkali halides, nitrates, and sulfates, even the practically insoluble heavy earth metals. Additionally, several types of surfactants with different polarization features and alkyl chain length have been employed. As for the recent models, due probably to the preferential application of long chain amines as collectors in industrial potash flotation, most researchers are only devoted to collectors with low polarization features like amines and sulfonates (Hancer and Miller, 2000; Du et al., 2014). Collector adsorption mechanisms are therefore proposed based largely on a neglect of carboxylates as collectors. However, carboxylates remain an important collector type in soluble salt flotation systems where both salt minerals can be floated using anionic collectors and cationic collectors. Fatty acid type collectors are still one of the widely used collectors for soluble salt flotation and also one of the first to be applied on an industrial scale for the separation of potash ore (Hernáinz et al., 2003; Titkov, 2004). Here we examine some recent models that are relevant to our study to reveal a long neglected specific ion binding effects in potash flotation."

Jan 1, 2016

By D. A. Barr

"The Galore Creek copper deposits are situated in the Stikine River district, 640 miles northwest of Vancouver, British Columbia. The deposits are primary cupriferous replacements localized in highly fractured zones lying in altered sedimentary, extrusive and intrusive rocks near the contacts of a potash-rich syenite porphyry complex which forms the core of a structural dome in Upper Triassic volcanic and sedimentary rocks. Ten deposits are distributed over an area of 3.5 by 2 miles and through an elevation range of 4,000 feet. The deposits share many of the characteristic features common to both the porphyry copper type of mineralization and pyrometasomatic deposits.Primary mineralization includes chalcopyrite and bornite, and is associated principally with pyrite and magnetite. The daminant alteration products are hydrothermal biotite and potash feldspar. Gypsum, anhydrite, garnet, chlorite and carbonate are commonly associated with sulphide minerals. Copper oxides, al-though present, are quantitatively of minor importance. The distribution of certain of the primary minerals reveals hypogene zoning characteristics.The results of stream sediment surveys, and airborne magnetic, ground magnetic and induced polarization surveys show important relationships to geologic structure and mineral deposits."

Jan 1, 1966

By A M. Goodwin

Detailed stratigraphic studies in the Birch-Uchi Lakes area have shown that the volcanic components are arranged in superimposed sequences, or cycles. Each cycle displays a progression from predominantly mafic effusives below to predominantly felsic extrusives above. Sedimentary rocks are preferentially associated with the felsic extrusives. Two volcanic cycles are represented. The average stratigraphic thickness of the volcanic rocks present is 31,000 feet. The original volcanic pile was probably in the order of 40,000 feet thick. The present lithologic composition is estimated to be: mafic volcanic rocks, 60 per cent; felsic volcanic rocks, 27 per cent; sedimentary rocks, 10 per cent; and others, 3 per cent. Gold occurrences are preferentially distributed with respect to the volcanic succession. Of fifty recorded occurrences, thirty-nine are located in the upper felsic division of the lower volcanic cycle; forty are associated with closely interbanded daciterhyolite pyroclastic rocks, andesitic lavas and siliceous sediments. The gold-bearing quartz veins either lie at the contacts of enclosing lithologic units or occupy cross-cutting fractures in one or more adjacent units.

Jan 1, 1965

By E. C. Roper

THE Britannia Mining & Smelting Company, Limited, have been operating their property at Britannia Beach, B.C., continuously for nearly forty years and have mined over 33,000,000 tons of ore from orebodies within a belt of highly sheared rocks, five miles long by 2,000 feet wide. The property is in the Coast Range mountains, about twenty miles due north of Vancouver. The mountains rise abruptly from sea level to elevations of 4, 500 feet within a horizontal distance of 7,000 feet. The topography has enabled the orebodies to be developed by adit tunnels. The active mining levels are connected to the adits by incline and vertical service shafts. The main service adits are the 2200, 2700, and 4100 levels (see Figure 1). The mine surface shops, three bunk-houses, and over one hundred dwellings form the townsite camp at the portal of the 2200 level adit. A small camp of one bunk-house and a few dwellings is situated at the 2700 level portal. The beach surface shops and camp, adjacent to the 4100 level adit, service the mill, foundry, and other beach installations as well as the mining from the 4100 level. The ore mined from the various orebodies is delivered to the 4100 main haulage level through a system of rock raises and intermediate tramming levels and is hauled on the 4100 level to the mill.

Jan 1, 1945

By W. A. Green

Introduction While pilot-mill operations were being carried on at Flin Flon, as described by R. E. Phelan (1), a detailed topographic map was being made of the area in the vicinity of the ore-body for later use in laying out plans for the final plant. The area covered by this survey was 6,600 feet by 6,600 feet, with contours on 2-foot intervals. As mentioned by Mr. Phelan, it was definitely decided at the end of November, 1927, to take up the option on the Flin Flon property and to proceed immediately with the plans for construction of a metallurgical plant at Flin Flon to treat 3,000 tons of ore per day, and of a hydro-electric power plant at Island Falls, Saskatchewan, to supply power for the future operations at Flin Flon. Railway Built From The Pas to Flin Flon Just as soon as the decision was made to go ahead with the construction work and opening-up of the property, it was of course essential to give immediate attention to the building of a railway to the mine. Many years previously, a preliminary survey had been made for a railway to branch off the Hudson Bay railway at a point 4.7 miles northeast of The Pas, and, during certain negotiations in 1925, the Provincial Government of Manitoba had agreed to guarantee the railway bonds necessary to finance the building of the line, so that it was possible to organize for this work immediately. A contract was let by the newly organized Manitoba Northern Railway Company to the Dominion Construction Company, Ltd., and Tomlinson, for the building of the railway to the mine, a distance of approximately 87 miles (see Figure 1). The Manitoba Northern railway is a subsidiary to the Canadian National railway, and all engineering and supervision of the contractors was done by the Canadian National engineers. Actual construction work was started in January, 1928. The first 52 miles of the railway from The Pas to Cranberry Portage is over fairly level, although slightly rolling, country, and a considerable portion of the route is over muskeg area. Rails were laid on top of the frozen muskegs. Gravel deposits were opened-up along the line and, before warm weather; sufficient ballast .was distributed in the muskeg areas to prevent thawing under the track, and thus give the necessary support to allow uninterrupted transportation over the line.

Jan 1, 1935

By D. Y. Li, C. D. Ma, T. Zhou, T. J. Cheng

In this paper, a number of experimental tests are carried out to study the strength difference on rectangular prismatic marble specimens with different height-to-width (H/W) rations. The specimens have a nominal size of 45×15 mm in the compressive cross-section (W×T) and different heights (H = 22.5 mm, 45 mm, 60 mm and 90 mm). It is to say that the height-to-width ratios are equal to 0.5, 1.0, 1.33 and 2.0, respectively. The quasi-static uniaxial compressive tests are finished by a servo-controlled INSTRON machine (the strain rate at about 10-5/s), and the dynamic compressive tests are finished by a diameter of 50 mm cylindrical SHPB apparatus (the strain rate reaching about 101/s). The rock failure process of marble specimens is captured by a high speed camera in order to distinguish the fracture propagation behaviour. It is found that the compressive strengths increase when the H/W ratio of marble specimen changes from 2.0 to 1.0 due to the end clamping effect both for quasi-static and dynamic loads. However, when the H/W ratio changes from 1.0 to 0.5, the apparent compressive strengths decrease both for the two loading conditions. The strength decrease of short marble specimens may be attributed to the change of failure mode from shear to slabbing, which can be identified by the fracture patterns of the specimens. Based on the uniaxial compressive tests, the slabbing strength of the marble was found to be about 40% of its UCS for the specimens with a nominal height-to-width ratio of 2.0. In addition, it is found that the dynamic increase factors (DIF) are affected by the specimen’s aspect ratios. It implies that the same aspect ratios should be used to compare the dynamic and static compressive strength of rocks. Meanwhile, both the static and dynamic tensile strengths of the marble are obtained by the Brazilian disc tests. The ratio of the dynamic tensile strength to the static tensile strength of the marble is about 2.68.

Jan 1, 2015

By Damien Gaboury

"Two practical methods for correlating two or more diamond-drill core intersections, using a stereographic projection software are presented. The first may be used to establish if two or more vein intersections are correlative, based on their core angles and diamond-drillhole attitudes. The second method allows prediction of main vein attitudes from numerous intersections, based on a spherical density contouring projection. The methods are suitable for: (1) correlating veins in complex orebodies; (2) ascertaining lateral continuity of ore for reserve estimations; (3) demonstrating the hidden complexity of an orebody; and (4) correlating and interpreting various planar elements.IntroductionModern mineral exploration relies on diamond- drill core data and on the ability of geologists to interpret them. Drill core generally yields unoriented information, unless an expensive orientation device is used. As a consequence, strike and dip of planar elements such as lithological contacts or mineralized veins cannot be determined easily. This is particularly true for blind deposits (covered by thick overburden) and complex orebodies, where field data cannot support drilling interpretations. Such a problem has been addressed previously using two and three diamond drillholes and several solutions were proposed based on trigonometry, and geometric and stereographic projections (Mead, 1921; Wisser, 1932; Fischer, 1941; Stein, 1941; Bucher, 1943; Gilluly, 1944; Addie, 1962; Mills, 1963; Lyons, 1964). However, these solutions are time consuming and not relevant to present day computerized data plots."

Jan 1, 1997

Presentation Outline Introduction Deposit Characteristics Geology Grade, Value and Tonnage Estimates 2006 Advanced Program Drilling Bulk Sampling DMS Test Facility 2006 Exploration Summary

May 1, 2006

By Marc C. Bétournay

Replacing diesel power in underground metal mining vehicles with available clean energy (e.g. hydrogen, lithium-ion batteries) is now a priority due to worker health issues, the increasing price of diesel, ventilation costs and air quality. Hydrogen fuel cells are a known and broadly applied power technology. They have been the focus of a dedicated research program to carry our proof of concept projects as well as regulatory developments for mining application. However, hydrogen remains a demanding energy vector to use in confined, underground applications. Standardization and safety considerations are being addressed in the industrial consortium Hydrogen Mine Introduction Initiative (HMII). Research projects are being carried out to resolve the gaps for regulated use. This article focuses on HMII objectives and Project results. The first has reviewed the relevant codes and standards and mine regulations, indicating that hydrogen and fuel cells could be allowed underground and that current codes, especially the Canadian Hydrogen Installation Code would be sufficient for hydrogen use. The second project established the standard hydrogen storage and distribution architecture along with related risks and safety requirements for its use in the third project, using an underground test chamber to delineate the behaviour of hydrogen leaks in confined conditions with various ventilation regimes and ignition studies. This project will end in 2013. It will be followed by the last project, which will establish best practices in support of regulations development, and develop the ISO standard for mine hydrogen infrastructure and underground application.

Aug 1, 2013

By A. M. Christie

Acknowledgements The following account has been compiled mainly from records and maps of Eldorado Mining and Refining (1944), Limited, hereinafter called the Crown Company. This work was done under the supervision first of R. F. Murphy, Chief Geologist, and later of E. B. Gillanders, Eldorado Mine Manager and Manager of Eldorado Exploration Division. W. F. James and B. S. W. Buffam are consulting geologists. Since 1946, S. N. Kesten has supervised geological work for the Company in the Goldfields area. Where maps of Eldorado properties have been included in this paper, the name of the geologist who examined the property is acknowledged on the map. Outline of General Geology The geology of the area is described in the Goldfields and Martin Lake preliminary maps of the Geological Survey and accompanying Paper 49-17. In brief, the Tazin series of Precambrian age, consisting mainly of sediments with minor interbedded volcanics and basic intrusives, is intruded and replaced by granite, now generally gneissic. The late-Precambrian Athabaska series of conglomerate and arkose, with interbedded basalt and andesite flows, rests unconformably on the older rocks. All these rocks are cut by small diabase dykes. The geological terms used in this paper and in the accompanying figures are standard with the exception of the term 'mafic rocks'. These include all the basic or dark coloured rocks of the Tazin group, such as amphibolites, biotite schists, and chlorite-epidote rocks (greenstones), whether they be of extrusive, intrusive, or sedimentary origin.

Jan 1, 1949

By V. Vorontsov

Catalysts Mo-Ni-S were prepared by combining MoS2 and NiS in weight ratios 1:1, 1:2, 1:4 and 2:1, each of which was admixed with 5%wt Ag and 5%wt YSZ to increase three-phase boundary surface area of the electrode. For comparison catalysts comprising Co-Mo-S in weight ratio of 1:1 of CoS to MoS2 admixed with 5%wt Ag and YSZ and pre-sulfided NiMoO4 were made. The catalysts were examined for electrochemical oxidation of hydrogen sulfide in solid oxide fuel cells (SOFC) at 850°C temperature. The catalyst prepared from 1:1 (wt. %) NiS:MoS2 demonstrated highest performance. Current density up to 1,330 mA/cm2 and power density up to 300 mW/cm2 were achieved using pure H25 gas, which are the highest among the reported H2S-powered fuel cells ever published in the literature. Anode materials of different NiS:MoS2 ratios have been characterized by means of X-ray diffraction (XRD), simultaneous TG/DSC analysis and Neutron Activation Analysis (NAA). TG/DSC and NAA results show that addition of NiS and Ag increases fuel cell performance due to improved structure/integrity of the anode. It has also been demonstrated that MoS2 is a suitable anode material in H2S-powered SOFC, with high activity towards H25 oxidation and thermally and chemically stable up to 850°C.

Jan 1, 2005

By J. Keith Haddock

"Introduction The Boundary Dam Mine is located 5 km south of the City of Estevan, Saskatchewan and is operated by Manitoba and Saskatchewan Coal Company Ltd., one of the Luscar companies. The entire production of 1.7 million tonnes per year is delivered to the Boundary Dam Generating Station of Saskatchewan Power Corporation. Geology There are basically two seams mined on the property, the main Estevan seam ranging in thickness from 3.0 m to 4.5 m with partings and the upper Roche Percee seam (roughly 15 m to 23 m above the Estevan) which ranges from 0.6 m to 2.0 m in thickness. Most of the reserves are concentrated in the Estevan seam, the Roche Percee only being mined whenever its thickness makes it economic to recover. The coal measures belong to the Ravenscrag Formation of Tertiary (Paleocene) Age. This formation is widespread in North Dakota and Montana and contains the lignite fields of North Dakota and subbituminous coals of Montana. The formation is gently tilted to the southeast at Boundary (0.5 degrees) and consists of weak sandstones, siltstones and silty mudstones. Reserves and Coal Quality The present minesite encompasses a coal reserve of approximately 50 million tonnes calculated to a maximum stripping depth of 37 metres or 20:1 mining ratio. The reserves form only a part of the total reserves in the Estevan area which are owned by the Saskatchewan Power Corporation. The coal being mined is classed as Lignite ""A"" and has the following specifications:"

Jan 1, 1985

By M. A. Stogran-Baker, S. Cole

"Fluorspar mining occurred in the St. Lawrence area from the 1930s until the mid 1980s. In 2013, CFI discovered a new ore body, the AGS vein, which proved amenable to more economic open pit mining methods. A new mill was designed to produce 200,000 tonnes per year of high quality, acid-grade fluorspar concentrate. The simple mill flowsheet includes crushing, dense medium separation (DMS), grinding, sulphide flotation, pulp thickening, fluorite flotation, thickening, and concentrate filtration. The type of flotation cell used is being installed for the first time in North America. Site clearing commenced in the spring of 2016, followed by mill building erection completed by the fall of the same year. Civil and mechanical installation as well as site-wide construction was completed by the end of September 2017. Commissioning commenced, and at the time of paper submission mill production is on track to ramp up to full capacity by the beginning of 2018. This paper will focus on the use of fluorine NMR analysis applied to fluorite and the development of on-stream analysis, flotation cell selection and the decision to install the new cells, and the water control program designed to maintain process control with the least possible environmental impact.HISTORY St. Lawrence is located on the south-eastern coast of the Burin Peninsula in Newfoundland and Labrador. The first occurrence of fluorspar in the St. Lawrence area was recorded in 1843 by British geologist J.B. Jukes (DNR 2010). Fluorspar was likely extracted in small quantities prior, however commercial fluorspar mining did not commence until 1933 at the Black Duck Mine. The Black Duck Mine operation processed ore by washing and screening – acid-grade was hand-picked from the oversize, the undersize was sold as a lower grade product. The Black Duck Mine was closed in 1941 (Wilson 2010). The American Fluorspar Limited (New Fluor) commenced operations on the Director vein in 1936, and was bought by Alcan in 1942 (Cooper 2012). Alcan also developed the Iron Springs as well as the Tarefare deposits. The Black Duck Mine mill had closed, and a new mill was built. This new mill crushed the ore prior to dense medium separation, the sinks of which were sent to Quebec for use in Alcan’s aluminum smelter (CFI 2016). Alcan shut down it’s mining operations in 1977 due to the dropping price of fluorspar as well as labour disputes. In 1986, the British-based Minworth Limited began producing ore from underground at Blue Beach North and Blue Beach South, as well as from open pits at Tarefare and Director veins (Cooper 2012). A new mill was built by Minworth in order to process the ore using flotation to produce an acid-grade concentrate. The low price of fluorspar caused Minworth to shut down operations in 1990. Whilst exploration has been ongoing, no mining had occurred in the area since 1990."

Jan 1, 2018

By F. R. Nogas

"Because of the elements of uncertainty and instabilitp associated with single-enterprise communities, there is increasing interest in the alternatives to developing additional new communities of this nature. Gulf Minerals Canada Limited has chosen a unique alternative means to accommodate employees at a new uranium mine/mill complex at Rabbit Lake in Northern Saskatchewan. Gulf has adopted a fly-in program which moves their staff from a 450-mile radius, in and out of the on-site facilities, on a 7-day rotation."

Jan 1, 1976

By Norman A. Parlee

Introduction The principal primary iron and steel producing capacity of the Dominion Steel and Coal Corporation is at the Dominion Iron and Steel, Limited, plant at Sydney, Cape Breton Island, Nova Scotia. The main raw materials are Cape Breton coal, Wabana (Newfoundland) iron ore, and Port-au-Port (Newfoundland) limestone. This plant, which was established at the turn of the century has gradually expanded its production facilities so that today its ingot producing capacity is over 720,000 tons annually. Principal operating units of the plant at present are three batteries of 173 Koppers by-product coke ovens with conventional by-product recovery equipment, three blast furnaces .of 15 ft. 6 in., 18 ft. 3 in., and 19 ft. 3 in. hearth diameter (inside the brick), one 700-ton hot metal mixer, ten open hearth furnaces (two of 175-ton capacity, three 12 5-ton, five 60-ton), one 10-ton electric furnace, a 40-inch blooming mill, a billet mill, a rail mill, a tie plate mill, rod and bar mills, and a wire and nail mill. Extensive machine shops and an iron and brass foundry are also available for plant maintenance and repairs. This paper will describe developments during the past five years and those now in process. It will also briefly discuss research being done and indicate the direction of future development.

Jan 1, 1951