Search Documents

By A. Hynes, T. Skulski, D. Francis

The Archean volcano-sedimentary succession in the LG-3 area has undergone two phases of deformation and has been metamorphosed to upper greenschist and amphibolite facies. Marine, fine-grained sediments and mafic pyroclastics comprise the lowest observed stratigraphic unit. These sediments are overlain by a thick sequence of submarine basalts and minor basaltic andesite. The lavas are characterized by high Al/Al+Si, Ti values, low Mg numbers and flat REE profiles (lOx chondrite). A sedimentary prism of coarse elastics which was deposited close to an exposed plutonic highland, overlie the volcanics. Massive lavas of basaltic andesi te and associated volcano-sediments comprise the uppermost stratigraphic unit. These lavas are characterized by high Mg numbers, Ni, Cr, LREE (lOOx chondrite) but low Ti, Al/Al+Si and HRee. The supracrustal rocks were intruded by tonalites and tonalitic gneisses.

Jan 1, 1984

By The Staff

"IntroductionThe difficulties to be overcome in shaft sinking and development at depth are centred at McIntyre in and around No. 12 shaft. Generally they have been due to increasing pressures and temperatures and to changes in geological structure. This paper describes the difficulties and the measures taken to meet them.No. 12 ShaftEarly in 1932 McIntyre decided to sink an internal shaft from the deepest level, the 3875, to explore and develop known veins extending below that horizon. The location selected was a point 1,500 feet south and 1,000 feet east of No. 11 shaft, the main operating shaft through which the men, ore, and most of the materials are handled Shaft and auxiliary equipment we1e laid out for 3,000 feet, that is to 7,000 feet below the surface. The shaft was to be capable of handling 1,500 tons of ore daily from the lowest level, and was to provide ventilation, compressed air, water, and electric power to service all levels.No. 12 is an internal, vertical shaft extending from the 3875 to the 6825 level and bottoming at 7,007 feet. It is a rectangular, four-compartment shaft, 21 ft. 9¾, in. by 6 ft. 3¾ in. outside the timber (Figure 1).There are two hoisting compartments and one airway compartment, each 4 ft. 10¾ in. by 5 ft. ¾ in. inside dimensions, and a combined manway, pipe, and cable compartment 4 ft. ¼ in. by 5 ft. ¾ in. Levels have been established at 150-foot intervals, pump stations and sumps at 1,000-foot intervals, and. there are two loading pockets, one at the 5525 and the other at the 6900 level.The shaft was sunk in two stages. The first stage, consisting of preparation above the 3875 level and sinking to 5585 feet, was completed by March 31st, 1935. The second stage of deepening the shaft from 5,585 to 7,007 feet was started August lst, 1946, and completed three years later."

Jan 1, 1950

By G. F. Round

In order to obtain values of angle of shearing resistance and initial resistance for McMurray oil sand for use in general design calculations, the shear strength of this oil sand was measured in a controlled strain type tester, modified so that the rate of deformation could be varied between 0.01725 and 0.1869 inches per minute. Effect of temperature was investigated by adapting the equipment to operate at both 71 ° and 185 °F. The data are reported in terms of angle of shearing resistance and initial resistance for varying rates of deformation, composition and temperature. While the main sets of results reported here were obtained at a bulk density range of 108.7- 109.5 lb. / cu. ft., some results were obtained at a bulk density range of 101-102 lb. / cu. ft. Analysis of varance tables have been drawn up from the results obtained from least squares correlations and significance tests applied. It was concluded that oil content and temperature were significant variables for the degree of shear strength developed by the oil sand; increase of oil content and decrease of temperature each cause an increase in shear strength. The bulk density range 108.7 to 109.5 lb./cu. ft. gave angles of shearing resistance from 30° to 40° and initial resistance values of 0.37 p.s.i. to 0.85 p.s.i. For the bulk density range 101 to 102 lb. / cu. ft., lower values of shear strength were obtained, indicating that compaction density was also of importance

Jan 1, 1960

By J. Keith Haddock

"IntroductionThe Bienfait Mine is operated by Bienfait Coal Company Ltd., one of the Luscar Limited group of companies. Situated 5 km southeast of the town of Bienfait, Saskatchewan, it can produce 2.0 million tonnes of lignite annually in addition to 158,000 tonnes of char from a carbonization plant located on the property. Geology The economically mineable coal seams of the Estevan area are found in the Ravenscrag Formation. The lignite-bearing sands, silts and clays were deposited in Early Tertiary age, in an inland sea centred in the Williston Basin of North Dakota. The top of the Ravenscrag is an erosional surface, overlain by Tertiary or Quarternary sands and gravels or glacial till. The regional structure is a gently plunging syncline which dips to the southeast at about 0.3 degrees. There are minor undulations in the Bienfait area which are due to differential subsidence during deposition. Sporadic faulting is probably a result of glacial pressures, and preglacial and glacial channels are responsible for washout zones and the abrupt irregular subcrop found in the area. There are two economic coal seams in the Bienfait area, an uppe; seam locally known as the Roche Percee, and a lower seam, the Estevan. Both seams have been extensively mined since lignite mining began in the area in the late 1800s. The Roche Percee remains only in a small portion of the Bienfait Mine and comprises a very minor portion of the reserves. It averages 1.74 m thick under 8.1 m of overburden. The till rests on top of the Roche Percee and due to weathering the seam is generally of poorer quality. The Estevan seam comprises the majority of reserves at Bienfait. The main seam which is being worked on consists of an upper bench averaging 2.75 m, a carbonaceous parting of 0.21 m, and a lower bench of 0.92 m. Overburden depth above this seam varies from 21.0 m to 38.0 m."

Jan 1, 1985

By W. R. Tyson

Pipelines for the transport of gas and oil are being designed to operate at increasing pressures in increasingly harsh environments. The steel used to construct these pipelines must have adequate toughness to tolerate weld imperfections (i.e. withstand bending strains) and to arrest running cracks (i.e. to prevent propagation of axial fractures). The problems posed in specifying suitable toughness parameters and the approaches currently being used to measure them are discussed.

Jan 1, 2005

By A. J. MacEachen

"LIKE ALL OTHER NOVA SCOTIANS, I have been thrilled during the past few years with the growing evidence that substantial reserves of oil and gas are being discovered off the Atlantic coast of Canada. There are those in this province who believe that large-scale commercial production is just around the corner, and that when it starts Nova Scotia will begin to float on a sea of royalties. These overly optimistic people, of whom I am not one, are convinced that with the first barrel of oil shipped to market, Nova Scotia can forget its financial problems while its people take on the luxurious lifestyle of the shieks of Kuwait or Saudi Arabia. You and I know, however, that even though offshore oil and gas may turn out to be the greatest gift nature has ever bestowed on Eastern Canada, it may take some considerable time before the reserves can be accurately assessed, before the industry can become fully operational, and before the benefits of production can be translated into royalties and tax revenue, improved public services, new industrial facilities and more jobs. While it is premature for the ordinary Nova Scotian to take on the habit of buying expensive cigars and lighting them with ten-dollar bills, it is not too early for him to insist that governments and industry plan intensively and well for the beneficial exploitation of undersea resources."

Jan 1, 1973

Abstract - A method to extract certain types of error variance information from paired data is presented, which constitutes an important tool for the calibration of Gy’s formula for variance predictions in the sampling of broken ores. The research summarized here complements publications by others on geochemical precision. The model and method proposed for treating duplicate data provide a practical means of deriving separate estimates of the purely analytical and aliquot sampling variances, from a unique set of duplicate assays, and, hence, proposes a new avenue for estimating effective mineral grain size.

Jan 1, 1998

By Gae On Kim, Ki Baik Kim, Suk Hoon Kang, Tae Kyu Kim, Sanghoon Noh

"Advanced radiation resistant oxide dispersion strengthened steel (ARROS) is being developed as a fuel cladding tube material for future nuclear reactor system applications. The research activities consist of advanced radiation resistant ODS steel development and fabrication technology development of ODS steel structural components. One candidate material with a chemical composition of (in wt%) Fe-10Cr-1Mo-0.5Mn-0.1V-0.25Ti-0.35Y2O3and was selected as representative materials, and this material was named as the advanced radiation resistant ODS steel (ARROSTM).On the basis of this ODS steel composition, an optimized fabrication process of structural components such as plates, sheets and tubes has been established through various process conditions in mechanical alloying, hot/cold working, and heat treatment processes. These R&D activities are expected to contribute to the realization of ODS materials in the future.INTRODUCTIONA sodium-cooled fast reactor (SFR) is being developed at the Korea Atomic Energy Research Institute (KAERI) with a view to economics, safety, reliability, and sustainability. The prototype Gen-IV SFR with a capacity of 150 MWe is under design, and this prototype reactor is scheduled to operate from 2028. For a commercial SFR system application, it is necessary to develop an advanced structural material having both high creep strength and irradiation resistance at high temperatures (Jeong, 2014). Oxide dispersion strengthened (ODS)steel is one of the most promising structural materials because of its excellent creep and irradiation resistance on the basis of uniformly distributed nano-oxide particles with a high density, which is extremely stable at high temperatures under a neutron irradiation environment for a prolonged operating period(Kim, 2016). As the first step, several batches of ODS steel were designed and the candidate samples with a 2 kg scale each were fabricated by mechanical alloying, hot isostatic pressing and hot rolling processes. The mechanical properties of these samples were evaluated. Up to now, two candidate materials with chemical compositions of (in wt%) Fe-10Cr-1Mo-0.5Mn-0.1V-0.25Ti-0.35Y2O3 was selected as representative materials, and these materials were named as the advanced radiation resistant ODS steel (ARROSTM).The next step was to optimize the fabrication process of the ARROS compositions for in-core structural components such as the fuel cladding tubes of a SFR. An optimized fabrication process of fuel cladding tube with a composition of ARROS has been established through various process conditions in mechanical alloying, hot consolidation, hot/cold working and heat treatment processes. Joining technologies of the ODS steel tubes is being developed using solid-state welding such as magnetic pulse welding, friction stir welding and diffusion boding. It is expected that the development of ARROS will contribute to the realization of a commercial SFR with high economics and sufficient safety in the future. In this paper, the study of fabrication process of ARROS structural components is introduced."

Jan 1, 2017

By Vic Briccardi

Energy Management Challenges The Holistic Standard to Energy Management Energy Management Information System (EMIS) "Best Practices?: Energy Management Maturity Curve De Beers Canada Profile & Mine Locations Significant ROI Driven by Real-Time Energy Visibility Mining Energy KPI?s Summary: What Does EMIS Deliver? Q&A Session

May 1, 2013

By W J. Riva

This paper reviews the circumstances that led to the development and construction of a commercial-scale vertical shaft carbonizer at Conmore, Alberta. This form coking process may be regarded as having potential application in other areas. Coal pelletizing offers a promising method of decreasing coal agglomeration costs under certain circumstances. Pellets can be rolled easily from -35-mesh coal, provided that a minimum of -200-mesh coal is present. Bentonite was found to be the best binder and was most effective when added in amounts of about 2 per cent. The water content of the coal pellets was observed to vary from 18 to 23 per cent. As a by-product of this investigation, it seems possible that fine coal could be converted into stoker feed by this process. A short investigation of the effect of heating rate on the carbonization of pellets was conducted. The low maximum heating rates in certain temperature ranges, necessary to avoid crack formation in the pellets as reported by other

Jan 1, 1964

By A. Ignatieff

Introduction Some interest is being shown in Canada in underground gasification of coal and, as developments have now taken place in several countries of the world, it is thought that a review of progress, particularly from the viewpoint of a mining engineer, may be of interest. The literature on the subject, and notably that of Russian origin, is already very voluminous. The various methods of underground gasification of coal have evolved from initial attempts to employ underground workings as gasifiers of previously fragmented coal or to use some method that involves little or no preparatory work underground. The 'stream' method, shown schematically in Figure 1, has been the only one used in tests to date in countries outside the U.S.S.R. Other methods, involving preparatory work underground prior to gasification, are the early 'chamber' method, where fragmented coal was gasified in rooms between inlet and outlet entries, and the underground borehole' method, illustrated in Figure 2, where gasification is developed in a succession of boreholes which are temporarily sealed and then abandoned in turn after gasification. The stream method appears. to be particularly suitable for pitching seems as it is claimed that the pitch prevents ash accumulation or serious blockage from roof falls, and it also aids the circulation of the stream. As a considerable proportion of Canadian medium and high-rank coal seams are inclined, it would seem that, at least at the outset, the stream method or a modification thereof would be the one most applicable to all but the Saskatchewan lignite fields and the flat domestic-coal fields of Alberta.

Jan 1, 1949

By V. Aitken

Line-of-sight radio control has received widespread acceptance for use in many mining methods because today’s technology offers improved economics and personnel safety. Significant advances in higher autonomy for mining machines are not currently seeing widespread use even though they offer great future potential. With autonomous capabilities being a longer-term goal, a logical sequence of advances based on TeleRemote control is proposed. Under Tele - Remote control, the operator is in direct control of the machine at all times. Three levels of Tele - Remote control systems are presented including line-of-sight, extended line-of-sight, and full load-haul-dump applications. Distributed control and sensing subsystems arranged in a vehicle control area network support incremental system expansion through the three levels of TeleRemote control and prepare the machine for integration of higher levels of automation as mature technology becomes available. This approach allows full exploitation of today’s mining automation technology with a flexible future growth path.

Jan 1, 1998

By Jo Render

Expectations of your management approach ??Life of mine applicability ??Tailor scale of activity to scale of project ??Assess impacts, risks, and opportunities ??Use global good practice, backed up by rigorous analysis ??Support with trained monitoring and evaluation team ??Information infrastructure to allow ongoing trend analysis and tracking of progress ??Public reporting using standardized indicators Yes, we are talking about a ?management system?

May 1, 2011

By L. Chunpongtong

ABSTRACT Oil sands production occurs on a massive scale, making orebody estimation a challenge. In rainy conditions, operators can have difficulty accessing ore at the mapped location. Without enough inventory as a buffer, the high-cost stockpile is depleted quickly, necessitating the removal of significant amounts of overburden and interburden to meet plant feed requirements. The inventory curve—a plot of ore inventory on a period-by-period basis—plays an important role in selecting an appropriate scheduling scenario. This paper presents a programmable method for creating an inventory definition by using a pit optimization tool.

Jan 1, 2014

By George E. Cole

Introduction In view of the fact that, during the past year, two Manitoba mines-Flin Fion and Sherritt Gordon-have entered the list of producers and have materially increased that Province's contribution to the metal production of the Dominion, it would seem appropriate at this time to review the progress of the industry in the Province, with particular reference to the out-standing metal-mining developments of the past decade. That these two mines have been able to continue their operations in spite of the low prices of copper and zinc adds a touch of brightness to the industrial life of the Province. Depression in metal prices is not encouraging to the mining industry, but it does stimulate efficiency in methods and costs of production. As two thriving towns have grown around the two mines, the will of the management to carry-on is of great consequence to Manitoba, this year so hard hit by the .agricultural depression. And, much as it is a pleasant feature in the mining situation that these mines have been able to continue operations, nevertheless it must be noted, in reviewing the mining developments of the past few years in Manitoba, that the Province was fortunate enough to profit by good times, in that an industry was established which gives evidence of permanency. In the metallic field, the section of Manitoba that first received attention from prospectors was the boundary district, west of the Lake of the Woods. Several claims were staked here at the time of the gold boom in the neighbouring Ontario area. But the first real interest in metalliferous deposits dates from the discovery of gold in March, 1911, in quartz veins on the shores of Rice lake, some twenty miles east of lake Winnipeg. Systematic and organized prospecting of the pre-Cambrian areas of the Province may be said to have commenced with that discovery. The first gold discovery in northern Manitoba was made at Wekusko (Herb) lake in 1914. This was followed by the discovery of the Flin Flan and Mandy copper ore-bodies in 1915 on Flin Fion and Schist lakes, respectively.

Jan 1, 1932

By Margaret Armstrong, Chris Roth

Abstract -Estimating ore reserves for vein type deposits is a two-stage procedure: first, calculate the geometry of the vein system, and second, estimate the grades within this system. The grade estimation can only be consistently performed if the vein geometry - its size, shape and orientation - has been correctly characterized. Getting the size and shape of the different veins right means that the ore tonnages will not be artificially inflated, e.g., by falsely classifying host rock as veins. Similarly, correctly estimating their orientation and location helps mine management decide on the appropriate mining technique, selective or not. When applying geostatistics to estimate the vein geometry all available information needs to be used and not just the standard lithologic indicator of being or not being in a vein.

Jan 1, 1998

By J. Holtzhausen

"An analysis of operating costs for underground mining operations in the current global economic climate considers the financial burden for a ventilation system to be in vicinity of 30–50%. These operating costs are often overlooked by management teams in the greater scale of things when looking to save money in the procurement phase. This oversight to operational costs can be as little as the effective delivery of ventilating air to the work zone. One of the biggest opportunities for substantial savings and improvements can be realized in the selection of a quality vent duct that is suitable and fit for purpose. The key component to the selection process for quality products is a solid selection criterion that is followed during the tender process. This allows the management team to filter out unsuitable suppliers and products. The case study identifies some of the key components that were considered in the procurement and selection process for lay-flat ducting products. These included the characteristics and strength of the materials. The selection criteria also considered a ducted performance comparison that offers the best aerodynamic performance with some of the following components. • Airflow at Duct Face (m³/s or cfm), Fan Pressure (Pa), Air Power (kW or hp), Assumed Fan Efficiency, Annual Running Costs, K – Factor or Lambda, Leakage Factor, Joining Method and available Duct Lengths with weights. • Critical components considered were the current Testing standards available for: o Bursting Strength AS 4878.5, Mass AS 2001.2.13, Tensile Strength AS 4878.6, Tensile Strength AS 2001.2.3.1, Tear Strength AS 2001.2.10, Tear Strength AS 4878.7 • Other key considerations were: o Warranty Claim, Damage claims, Local storage / operations, community engagement and relationships, current testing data, previous issues, after sales service with technical assistance, etc. Hidden costs associated with product failures and operational stoppages are often not quantified during the tender process. Buyer beware. INTRODUCTION The largest constraint underground mining operations currently face are their operating efficiencies and electrical costs. The overall cost of an operations ventilation system and its components requires more focus to identify what opportunities exist to maximise efficiency and effectiveness. This tender process may not always be clearly understood and it should be broken down into fewer components to achieve quantifiable results."

Jan 1, 2019

By X. Cao

Friction stir processing (FSP) is used to produce wrought microstructures at the surface of sand-cast aerospace grade magnesium alloy ZE41A-T5. It is found that the microstructure is significantly refined in the stir zone and the flow arm. The stir zone is largely comprised of equiaxed magnesium grains of approximately 4.5 pm compared with about 50 µm in the base cast material. In the stir zone, however, abnormal growth of some grains is also observed. Vickers microindentation hardness tests indicated that the stir zone experiences some increases in hardness. Single surface passes with low distortion, lack of pores and cracks were successfully obtained indicating the great potential of the FSP technique for modifying, improving and repairing magnesium alloy castings. This will probably open new opportunities to apply magnesium alloys in aerospace industry.

Jan 1, 2007

By H. R. Shakeri, R. Mayer, M. J. Worswick, A. Rahem

The current focus of research and development in transportation industry is to use lightweight materials such as aluminium alloys for more structural components. In this regard, maintaining safety of the passenger and vehicle is the most important; therefore crashworthiness of components made of lightweight materials must be evaluated prior to sizable application of these materials. The focus of the present study is to understand failure and damage mechanisms during the axial crushing of aluminium tubes made of A1Mg3.5Mn alloy of 2 and 3.5 mm thickness. Due mainly to complexity of the crushed tubes, a microstructural approach is considered. In this study optical, stereo as well as scanning electron microscopy techniques have been used to study damage and failure mechanisms in these types of tubes, which are essential energy absorbing components in passenger vehicles.

Jan 1, 2006

By M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9 m × 2.05 m AG mills (fixed speed) are used in parallel in a dry operation. The performance of AG mills has been lower than the target value indicated by an increase in the product size (P80) from 450 µm (target) to 515 µm and low power draw (50% of nominal). By simulation it was found that increasing the liner lifter face angle from 7 to 30o while keeping the original lifter height (i.e., 22.5 cm) could provide an appropriate charge trajectory. When the proposed liners installed in one of the AG mills, the throughput increased by 27%; when 5% (v/v) balls were added the throughput increased by 40%. The product size also decreased from 515 to 501 µm.

Jan 1, 2012