Search Documents

By G. A. Sutton

This paper, describes a case example from San Manuel mine, where in situ copper leaching of the supergene zone was done over a 14 year period (1986–1999) in conjunction with underground and open-pit mining operations of a copper porphyry deposit. In 1993–1994, testing of well fields was done to determine the amount of copper that would be recovered from in situ leaching of the supergene zone, which was composed primarily of chrysocolla and copper-clay minerals. It was determined that the leach fluid would reach 70% (‘sweep efficiency’) of the copper minerals and that 75% of them would be leached for a recovery of 52% of the acid soluble copper. However, the final results from Zone 6, which had the longest leach history, showed that approximately 42% of the acid soluble copper was recovered, indicating that the `sweep efficiency’ was closer to 55%. Comparison of drill-core assay data from two holes, one drilled before (ARM158) and the other after (SMO9607) leaching, also indicate that approximately 42% of the acid soluble copper was recovered. The discrepancy between the predicted (52%) and actual (42%) recovery is probably related to a combination of factors, including difficulty in maintaining fluid saturation, channeling effects and gypsum precipitation. INTRODUCTION In situ copper leaching at the San Manuel mine, Arizona, was initiated in 1986. It was recognized that some of the copper oxide resource was not going to be economically recoverable by conventional open pit and heap leach methods using solvent extraction and electrowinning (SXEW). A high stripping ratio would be required to access part of the resource. At the time, in situ leaching was becoming popular in the uranium industry but the approach was virtually unknown in the copper industry, especially not at a large scale.

Jan 1, 2019

"In today’s world of complex projects, where engineering and execution are supported by a high level of project management and systems, how critical is the human factor in design engineering. Based on his involvement on a variety of projects, Tony Lipiec will relate his experiences as the impact of 4 factors: the ‘team’ involved in the design and execution of the project; the project and information systems supporting the project; the impact of scope, time, and budget; and finally the selection of the proper success criteria to judge the project and the people who have enacted the project.The discussion of the team will relate to the quality of people and the impact of their knowledge, attitude and experience. It will also look at the relationships and interests of the various stakeholders. Decision making and taking responsibility will be discussed.Supporting the team are the management, document and information systems. The value that these systems bring to the project as a whole will be examined. How project size impacts the applicability of the systems will be discussed.Scope, time and budget are recognized as critical. Reference will be made to the interplay between these components which are vital to project success. The issue of iterative design and whether it is necessary will be considered together with the development of supporting technical information.Finally the selection of the proper success criteria and the awards provided to the team can have a big impact on the final, production success of the project. The author will discuss his views on the impacts of these on EPCM projects."

Jan 1, 2016

By H. Utsunomiya, J. Su, K. S. Tamimi, S. Yue, M. Sanjari, L. Kestens, A. S. Kabir, R. Petrov

The recrystallization and texture evolution of AZ31 sheets obtained through two stages was investigated at different stages of post-rolling annealing. The specimens were rolled at the temperature of 100? and at a fast speed of 1000m/min and low speed of 15m/min with a reduction of 30% in one pass. The results show thatAZ31B sheets rolled at 15 m/min and 100 °C has fractured for reductions of more than 30% per pass. However, by increasing the rolling speed to 1000 m/min the rollability was improved significantly and the material can be rolled to reductions of more than 70% per pass. The high speed and heavily deformed materials are fully recrystallized even at 100 °C.

Jan 1, 2015

By J. M. D. Wilson, W. Petruk, C. Coté

"The behaviour of minerals in the Mount Wright spiral circuit was investigated to find methods of improving iron oxide mineral liberation and recovery. The feeds, concentrates and tailings from rougher, cleaner and recleaner spirals in one mill line were sampled before and after the sizing screen openings were reduced from 2 mm to 1.6 mm. Sized fractions of each sample were analyzed with the MP-SEM-IPS image analysis system at CANMET to determine mineral quantities and liberation characteristics of the iron oxide minerals. Mass balance techniques were used to calculate stream recoveries of iron, silica, total iron oxide minerals, hema¬tite, goethite, quartz, ferromagnesian silicates, and liberated and locked total iron oxide minerals for each sieve fraction.The reduction of the sizing screen openings increased the ap¬parent liberation of the total iron oxide minerals in the screen undersize from 89% to 94% and raised the over-all iron recovery from 84.4% to 85.3%. Apparent liberation of iron oxide minerals in the cleaner sand also increased from 70% to 85%, but the – 75 µm fraction re¬mained the only fraction containing an acceptable amount of liber¬ated iron oxide minerals in each case. Due to limitations of spiral and grinding efficiency it is recommended that the cleaner sand be screened at 300 m, the +300 m fraction be reground, and the – 300 p.m fraction be rerouted to the rougher spirals.The amount of fine liberated iron oxide minerals (– 106 m) lost in the tailings was 46 TPH in mill line 3. This value represents 41 wt % of the free fine iron oxide minerals, or 7 wt % of the total iron oxide minerals in the spiral feed. Further work is needed to investigate the possibility of recovering this material by other methods.Middling iron particles (010 50%) and presumably free gangue in the size range –300+ 75 m tend to be recovered by spirals by entrapment."

Jan 1, 1990

By R. A. Gannicott

Trend surface analysis was used to investigate the geochemical dispersion patterns of Si, Ai, Fe, Mg, Ca, Na, K, Ti and Rb in the footwall of the Seneca massive sulphide prospect in southwestern British Columbia. Surfaces for various element ratios were also produced to see if the distributions of the elements are related to each other. Trends developed by the elements redistributed during hydrothermal alteration may be difficult to detect for various reasons, such as too few and widely separated sample points, random analytical errors or local variations in rock chemical composition that are not related to regional trends. Trend surface analysis is useful to distinguish regional trends from local fluctuations. The computer program used in this study is capable of calculating surfaces up to the 6th degree polynomial, but provides for automatic termination when the variables in the equation for successive surfaces become effectively collinear. With the relatively small number of data points used (21 samples) in this study, such termination occurred after the quadratic surface. Results show that, at the Seneca prospect, Mg and K increase, and Na and Ca decrease, toward a common centre which corresponds closely with the best drill-core intersections of ore. The centre is interpreted as a volcanic vent and as the source of mineralization . Quadratic surfaces for element ratios show that K/Ca decreases and Fe/Mg increases away from this vent. Thin-section and X-ray diffraction analyses indicate that these variations reflect sericitization of plagioclase and an increase in the Mg content of chlorite near the vent. The mineralization , rock types and element dispersion patterns at the Seneca prospect are similar to those reported for volcanogenic massive sulphide deposits at Bathurst, New Brunswick, and in the Hokuroko district of Japan.

Jan 1, 1979

By B. R. Schneiders

"Atikokan is 200 km west of Thunder Bay and earned its mining fame from the discovery of the Steep Rock Iron Range in the late 1930s. Gold, however, was discovered in the Atikokan and Mine Centre areas in the late 1800s and eventually led to one of Ontario's first gold camps, and a total production of approximately 52,000 oz of gold and 174,000 oz of silver from 218,000 tons milled.The general geology of the area consists of Early Precambrian rocks of the Wabigoon and Quetico subprovinces, separated by the east-trending Quetico Fault. The Wabigoon Subprovince, to the north, consists of metavolcanics, minor metasediments and granitic batholiths. The Quetico Subprovince consists of metasediments and granitoids. Small ultramafic plutons occur throughout the metasediments.Within a 50-km radius of Atikokan, more than 50 gold occurrences, prospects and past producers have been discovered since the 18oos. The Atikokan Gold Study performed by the Ontario Geological Sur vey (Wilkinson, 1980, 1982) defined three types of gold mineralization in which gold is concentrated in quartz and quartz-carbonate veins:I) Metavolcanic-Hosted, Stratabound Type-associated with altered felsic fragmental units and chemical sedimentary rocks; possible gold mineralization source rocks. The mineralization is due to metamorphogenic (epigenetic) enrichment. Associated with dynamic metamorphism events and/or felsic intrusive events.2) Marmion Lake Batholith Type-occurs within the gneissic core of the batholith associated with north east-trending lineaments, representing faults or shear zones. Mineralized veins are related to several periods of deformation and shearing, suggesting that metamorphogenic veins were produced during dynamic metamorphism.3) Contact Zone Type -occurs in the contact zone rocks between gneissic batholiths and meta volcanic belts. Hydrothermal solutions produced during several deformational periods acted to leach and concentrate gold mineralization. Localized, discontinuous shear zones host the epigenetic (metamorphogenic) veins.Twenty-one properties in the area were mapped and sampled, and researched petrographically and geochemically. Geological data from the Atikokan Economic Geologist Program of the Ontario Geological Survey are used in discussing the types of mineralization, genetic models, and exploration targets and techiques."

Jan 1, 1983

By G. Itoh, S. Fukasawa

The Al-Zn-Mg alloys have been known to be susceptible to stress corrosion cracking (SCC), which is based on intergranular cracking arisen from hydrogen embrittlement (HE). The mechanism of HE has not been fully understood yet. In order to elucidate the mechanism of HE, we need to investigate the behavior of hydrogen in the alloys. In this paper, behavior of hydrogen in an Al-5.8%Zn-2.4Mg alloy was investigated by means of hydrogen microprint technique, a method to visualize location of hydrogen emission from specimen surface as silver particles. One side of the tensile test pieces was electrolytically polished and then covered with photographic emulsion. Hydrogen was pre-introduced into the test pieces from opposite side by cathodic electrolytic charging for 30min. Then, the test pieces were stretched with continuing the charging. After that, the specimen was fixed, rinsed, dried and observed with a scanning electron microscope. As a result, silver particles were observed on some grain boundaries.

Jan 1, 2015

By Alfredo Bambaren

First Encounters between Communities and Mining 1. Importance, meaning and process 2. Antamina?s study case 3. ?Self-organization? theory (NLP) 4. The story we tell, the values we live 1. Importance, Meaning and Process ? First encounter stays in mind as a model. ? First encounter means foundation. ? First encounter builds the story.

May 1, 2010

By Niels Verbaan, Ron Molnar, David Dreisinger

"An acidic chloride leach solution was generated from the treatment of an ore containing the following value elements: silver, gold, indium, gallium, copper, zinc and lead. Iron was also co-extracted into solution as a ferric chloride species. Iron extraction was a significant component of the overall acid consumption of the leaching process. The recovery of iron by solvent extraction and water stripping was investigated. Tri-butyl-phosphate (TBP) was very effective at recovering iron from the leachate. The water strip solution could be decomposed to produce ferric oxide (hematite) and hydrochloric acid for recycle via hydrothermal hydrolysis or pyrohydrolysis.INTRODUCTION The Malku Khota deposit is situated in the eastern part of the Bolivian Altiplano at elevations between approximately 3,800 and 4,580 meters above sea level (Figure 1). The project is located 98 km east-southeast of Oruro, and 85 km south of Cochabamba in a relatively remote area."

Jan 1, 2016

By Alan B. Morrow, William A. Poe

"Minerals processing operations are constantly challenged with improving production rates, yields, energy efficiency and process stability. Advanced Process Control has proven to be an effective tool for improving operations by capturing the full process capabilities consistently. However, the velocity of applying the technology as well as the sustainment of these significant benefits has been hampered by the usability of the software and adaptability of the applications.Some of the new technology developments that improve the usability and adaptability of advanced process control include:• modern and intuitive user interfaces,• customizable models to support unique process behavior,• fast and flexible OPC connection tools,• automated model building,• integration with first principles dynamic models and• improved performance monitoring.This paper will briefly discuss the new technology developments that have improved the usability and adaptability of advanced process control and how this can affect minerals processing operations.In today’s environment, Minerals Processing plant managers continuously face new challenges and requirements including:• higher energy efficiency,• increased run lengths,• reduced product quality variability,• reduced emissions,• higher availability, and• lower operating costsOperating a unit to meet these challenges in real time is not easy for operators and conventional process control systems. However, innovatively using existing technologies in Minerals Processing plants can improve operations on a minute by minute basis and reap significant benefits.Advanced Process Control (APC) can extract the maximum performance benefits from existing equipment while respecting plant operating constraints. Expensive capital projects to upgrade equipment are not always necessary. Advanced Process Control can deliver significant economic benefits by maintaining the plant at its most profitable point as conditions change."

Jan 1, 2016

By R. W. Thompkins

"PREFACEPart 1 of this paper, published in the September issue, covered the occurrence of uranium, radiation from uranium ores, the uranium series, radioactive theory, radioactive equilibrium and application to the radon series, the working level, the theory of emanation and diffusion, transport by thermal diffusion of radon emanating from porous rocks, and definitions.The October issue carried Part 2, which dealt with radiation theory applied to uranium ores, other radon migration factors, factors affecting the radon gas release rate, the measurement of radon gas emanation rates, the tunnel concept, variation of emanation rate with grade and estimating radioactivity from grade analysis.Part 3, in this issue, concludes the series by discussing the techniques for controlling radiation and providing some example calculations.17.0. Techniques for Controlling Radiation17.1. Altering the Factors In the Diffusion EquationIt has been noted that radon gas emanates from the surfaces of exposed ore to the mine atmosphere. The diffusion laws establish the rate of this flow. The fundamental relationship is that the rate of flow (J) is a function of the pore concentration and the distance from the surface. It is expressed as: []If any of these terms is varied, either naturally or artificially, the rate of gas emanation will be altered.Altering the Diffusion CoefficientThe literature describes many ways to lower the radon gas emanation rates which are dependent on changing the diffusion coefficient:1. A layer of ice on top of a tailings dam or on a soil.2. Humid clayey materials and swamped soils over a radon source."

Jan 1, 1982

By R. J. Mitchell

"High narrow backfills of significant strike length approach the stress conditions associated with a free standing wall but this lower bound design approach is not considered efficient for earth structures. This paper considers the design of high narrow backfills using upper bound limit analysis, retaining wall theory with backfill arching and centrifuge model tests. Complex toe support situations pertaining to operational factors at Falconbridge's Lockerby Mine are investigated. It is shown that the susceptibility of high narrow fills to toppling is much lower than anticipated from the retaining wall analysis and that toppling can be avoided by a suitable toe support. It is also concluded that adhesion between the fill and an adjacent pillar can markedly increase the stability of the fill. INTRODUCTIONFalconbridge's Lockerby Mine pillar projects will expose cemented tailings backfills to heights (H) up to 55 m. The exposed backfills may have strike lengths (L) greater than the heights but are relatively narrow, having widths (w) of up to 12 m. The bulk cement content of the fills varies from 8.3% (12.1 T:C) to 3.0% (33.1 T:C). Exposed faces may have up to a metre of overhang due to stope overblasting, as shown in Figure 1. These fills have a solids specific gravity of close to 3.0 and were placed at a pulp density of about 68%. The tailings have a fairly uniform grain size with 32% less than 0.075 mm (200 sieve) and about 12% slimes (less than 0.02 mm sizes). The fill exposed by early pillar removal will be backed by adjacent, near vertical, ore pillars. Future pillar removal may expose similar fills which are not supported by an adjacent ore pillar but which will be backed by either an open void or by uncemented backfill. Furthermore, these fills may be undercut when the pillar slot is driven, further reducing stability (case 3, Fig. I) or a wedge could be left to help support the fill (case 2, Fig . 1). This paper presents limit equilibrium analyses for these various backfill conditions in a 22: 1 T:C fill and com- pares the results to data from centrifuge model studies at a scale factor of A= 157 as indicated in Figure I. Prototype fills have a 6 m deep cone plug of 16:1 T:C which is accounted for in the comparison of centrifuge model test with analytical results."

Jan 1, 1989

By G. Avramovic-Cingara, H. J. McQueen

The microstructure of commercially pure aluminum was investigated by using polarized optical microscopy (POM), orientation imaging microscopy (OIM), and transmission electron microscopy (TEM) techniques. Specimens were deformed in torsion at 400°C and equivalent strain rate of 0.1 s-1, to various strains of 0.2, 0.5, 1, 4, and 6. The results indicate that POM can usefully reveal grain and subgrain structures over a large field in aluminum. TEM is most suitable to study dislocation substructure and evolution of subgrains. While TEM microscopy and OIM are capable of resolving individual subgrains, OIM can not reliably distinguish subgrains with small misorientations, particularly in samples with low strain. On the other hand, the OIM technique is very useful in the analysis of many regions surrounded by high, medium, and low angle boundaries (HAB, MAB, LAB). Various misorientation maps were studied using different data processing methods. The analysis revealed that the subgrain size is relatively insensitive to strain. The fraction of low LAB ( < 5°) decreased and HAB (>15°) increased conversely with increasing strain, whereas MAB (5-15°) remained stable. The development of an increasingly bimodal grain boundary misorientation distribution is consistent with the predominance of dynamic recovery (DRV) in the evolution of microstructure, combined with geometrical dynamic recrystallization (gDRX), now called grain-refining DRV.

Jan 1, 2006

By N. Dahata

B206 aluminum?copper alloy has a potential for wider use in the automotive industry due to its light weight and relatively superior mechanical properties as compared to aluminum-silicon alloys. The possibility of casting this alloy via Lost Foam Casting (LFC) has not been investigated in detail. Therefore, the effects of foam types (T170B standard untreated EPS and T175-brominated EPS), coating types (Styro Shield 5553 and Styro Shield 5554), copper level (4.5 wt % and 5.0 wt %) and titanium levels (0.5 wt % and 0.25 wt %) were related to fillability, microstructure and microporosity. The metal velocity in T175 EPS pattern was higher than that in T170B EPS pattern. For T175 EPS pattern, the total solidification time was 3% higher and the loss of temperature for decomposition of EPS was lower than those in the case of T170B EPS pattern. The grain size, porosity level and maximum pore size were quantified using Light Optical Microscopy (LOM) and image analysis. The casting with T175 EPS pattern showed larger grain size relative to that with T170B EPS pattern. The porosity level and the maximum pore size decreased significantly when the titanium level was increased from 0.05 wt % to 0.25 wt %.

Jan 1, 2007

By Edouard Masengo

A long dyke will be constructed in a lake with rockfill placed by end dumping method. Its crest will be at elevation 521.5 m compared to the nominal lake level at 520 m. In the first portion, its height will vary from 1.5 m on a 35.1 m thick tailings layer to 18.3 m on about 0.5 m of tailings. In the second portion, the dyke will be built on native silty clay and will vary from 18.3 to 15.2 m in height. The tailings consist in stratified layers of fine-grained soils showing lateral and vertical segregation. The tailings are compressible and may develop excess pore water pressure on loading. The tailings overlie a thin layer of relatively soft native silty clay. The till beneath the silty clay is considered incompressible compared to the material above. After construction, as the tailings and silty clay consolidate, pore water pressures will dissipate and dyke stability will improve. Since dyke stability will increase with time, the primary concern is its stability during construction. As a result of construction activities, three potential modes of failure were identified and recommendations were provided regarding the measures that should be undertaken to increase dyke stability during construction.

May 1, 2003

By Jamal Asfahani

Abstract - Natural gamma ray well logging, an effective tool in geophysical prospecting, is used to investigate the radioactive and phosphatic layers in the Khneifiss mine in Syria. The interpretation of the gamma ray measurements, using numerical methods of analysis developed previously and applied successfully in some phosphatic areas in Syria, make it possible to define precisely the phosphate thickness from place to place in the study area. This technique has been successfully applied while studying seven boreholes in the area. Sixty-three core samples from phosphatic layers in the boreholes have been analyzed, using gamma ray spectrometry for the determination of P2O5 , U, Th, and K. Good correlation between P2O5 content and U concentration has been found. The total count gamma logs correlate reasonably well with the U core analysis, suggesting that radioactive equilibrium exists in the U decay series. These gamma logs can be therefore used effectively to quantitatively map the distribution of P2O5 and U. The characteristics of both subsurface phosphatic sand and phosphatic rocks have been investigated and outlined using a statistical approach. The affinity of uranium to some trace elements such as V, Sr, Cu, and Ni has been verified using correlation matrices of these elements.

Jan 1, 2002

By B. McFadzean, J. Taguta

In order to recover minerals by flotation, the sub-processes of collector adsorption onto the valuable minerals followed by bubble-particle attachment should occur efficiently. This paper investigates both of these sub-processes for various thiol collectors and their mixtures onto base metal sulfide minerals. The aim of the work was to investigate whether there is a correlation between the strength of the collector interaction with the mineral and the subsequent bubble-particle attachment. The collector-mineral affinity was measured experimentally using an isothermal titration calorimeter in order to determine the molar enthalpy of adsorption for each collector-mineral system. The bubble-particle attachment was measured using a microflotation device which essentially determines the hydrophobicity of the mineral. Sodium ethyl xanthate (SEX) and sodium diethyl dithiocarbamate (DTC) and mixtures thereof were used as collectors with either single minerals or binary mixtures of pyrite and chalcopyrite, respectively. The adsorption enthalpies of the collectors were interpreted with reference to the chemical structure of the collector molecule and showed that the greater the positive inductive effect of the collector, which may be qualitatively related to their pKa, the greater their affinity for the mineral surface. In the microflotation studies, recoveries were strongly related to the alkyl chain length but there was no correlation between the enthalpies of adsorption and the flotation recoveries. When mixtures of collectors were used there was clear evidence of synergistic effects and in the case of DTC/xanthate mixtures it is possible that this synergism is related to a DTC promoted oxidation of xanthate to dixanthogen. When mixtures of pyrite and chalcopyrite were used the flotation recovery and enthalpy of adsorption of SEX onto the individual pyrite particles in the mixture increased substantially compared to the case of pyrite alone. Mechanisms are proposed to interpret these important observations.

Jan 1, 2016

By Farzad Khodabakhshi, Adrian P. Gerlich

"In this article, cold spraying process was utilized to coat the surface of AZ31 magnesium alloy with a layer of AA7075 aluminum alloy. Thereafter, friction-stir processing (FSP) was employed to enhance the microstructure and consolidate the deposited layer. The grain structure and phase morphology were studied along with indentation hardness before and after cold spraying and friction stir processing. The magnesium substrate had an initial hardness of 74 HV which increased to 102 HV after FSP due to refinement of grains to <2 µm. The aluminum coating layer, provided improved surface hardness up to 160 HV, which further increased to 173 HV after FSP was applied.INTRODUCTION Cold spray is a material deposition process which can be used for surface modification, since it deposits material on a metallic substrate with little heating by way of high velocity ballistic impacts. Using cold spray technology, it is possible to deposit a wide range of coatings with various thicknesses by controlling the characteristics of the feeding powder and metal substrate, gas temperature, gas pressure, powder feeding rate, nozzle geometry, and gun traverse velocity. This process has been recently employed for surface modification in various aircraft and automobile structural applications. This has led to a broad range of research using this process for production and modification of different metallic and non-metallic systems. In the present study, cold spray process was used to deposit a uniform layer of aluminum-zinc alloy (AA7075) on the surface of AZ31 magnesium alloy. This coating was subsequently treated by way of friction-stir processing (FSP) as a new post-spraying modification technique to enhance the structural homogeneity and densification of the coated aluminum layer. This method utilizes a non-consumable rotating tool with a specially designed shoulder and pin that is plunged into the surface of metal to be modified and then moved along the direction of interest. The localized frictional heating between the rotating tool and workpiece leads to softening of the materials around the pin, and material extrusion through a complex flow of material from the advancing toward the retreating side the tool. To the author’s best knowledge, only a few reports discuss the modification of a cold sprayed deposit by FSP process. The microstructure and mechanical properties of the cold sprayed layer and substrate before and after FSP modification were examined using optical observations (OM) and indentation hardness testing. Furthermore, the AZ31 alloy substrate alone was treated with FSP as well, for the aim of comparison to the processed coating."

Jan 1, 2017

By Pierre Giasson

"Les avantages de l&apos;électricitéLe thème de la réunion 1982 de l&apos;ICM District No. 2: "" Le défi des années 80 pour l&apos;industrie minière de la Côte-Nord"" exprime trè s bien la réalité . En effet, la récession économique qui touche présentement tout le monde industrialisé, frappe de façon particulièrement sévère le marché du fer et de l&apos;acier. Il est donc primordial pour les industries minières de la CôteNord de minimiser leurs coûts de production. Comme on sait, une bonne part des coûts de production est directement reliée à la consommation d&apos;énergie.Si on retourne en arrière de quelques années, les prix des produits pétroliers étaient beaucoup moins élevé s que maintenant . Par exemple: A Philadelphie, en janvier 1930, le prix de l&apos;huile no. 6 (bunker C) était de 1.22$ le baril. En 1940, le prix mondial du pétrole brut se situait aux environs de 1.80$ le baril et augmentait très lentement jusqu&apos;en 1973. A la mi-octobre 1973, l&apos;organisation des pays exportateurs de pétrole (O.P.E.P.) surprend le reste du monde en annonçant que le prix du brut grimpe à S.12$ le baril. .. on connaît la suite.On sait qu&apos;au point de vue énergétique, le nord du Québec est l&apos;une des régions les plus avantagées au monde. Malgré le fait que notre climat soit plutôt défavorable, nous sommes assurés d&apos;une alimentation électrique à toute fin pratique éternelle, contrairement aux autres régions du globe. En effet, l&apos; hydro-électricité ne représente que 2.S070 de toute l&apos;électricité produite dans le monde.Une bonne partie de l&apos;énergie consommée dans les industries minières de la Côte-Nord est utilisée pour produire la vapeur. Or, il y a plusieurs avantages à produire de la vapeur à partir de l&apos;électricité:1. Le prix d&apos;achat d&apos;une chaudière électrique peut être moins de la moitié de celui d&apos;une chaudière à carburant fo ssile.2. Le prix de l&apos;électricité est plus bas que celu i des autres sources d&apos;énergie disponibles dans notre région.3. Hydro-Québec offre un programme spéci al de subventions et un prix garanti de l&apos;électricité, inférieur de 10070 à celui de tout autre combustible (1982).4. Souvent il est possible d&apos;utiliser l&apos;énergie hors pointe à un coût minime.S. L&apos;espace requis pour un chaudière électrique est beaucoup moindre. Par exemple: une chaudière d&apos;une capacité de 120000 Ibs/hre ne demande que SO pi? de plancher, c&apos;est-à-dire un cercle de 8 pieds de diamètre comparativement à environ 600 à 700 pi2 pour une chaudière au ma zout.6. Aucun espace n&apos;est requis pour l&apos;entreposage du carburant.7. Aucun espace n&apos;est requis pour la cheminée.8. Il n&apos; y a que très peu de pièce s mécaniques, donc ces chaudières demandent très peu d &apos;entretien .9. Les chaudières électriques ne génèrent aucune pollution, donc on n&apos;a pas besoin d&apos;équipement coûteux de contrôle de la pollution.10. Ces chaudières sont extrêmement rapides. En effet, on peut passer de zéro à la production maximum en moins d&apos;une heure si la chaudière est froide et en quelques secondes seulement si la chaudière est à sa température d&apos;opération.11. L&apos;efficacité de ces appareils est au moins de 9S% par rapport à 80-8S% pour les chaudières au ma zout. De plus, cette efficacité demeure la même quel que soit le niveau de production de la chaudière. Il faut faire attention ici: les manufacturiers proposent des rendements de 99% et plus, mais ceci ne tient compte que des pertes de chaleur à travers l&apos;enveloppe, et de l&apos;énergie nécessaire au fonctionnement de la pompe de circulation. Il faut ajouter à cela l&apos;énergie perdue à cause de la vidange qui varie selon le type de chaudière et selon la qualité de l&apos;eau d&apos;alimentation.12. Ajoutons simplement que ces appareils sont très facile à opérer du fait qu&apos;il n&apos;y a aucun système complexe à manipuler.Cependant, il y a un inconvénient non négligeable à utiliser l&apos;électricité comme source d&apos;énergie: comme on ne peut pas emmagasiner l&apos;énergie électrique, nous sommes à la merci du fournisseur."

Jan 1, 1985

By S. M. Chentouf, M. Jahazi, N. Bombardier, T. Belhadj

The main limiting factor in the commercial expansion of superplastic forming (SPF) of thin sheet aluminum alloys is the extent of cavitation phenomenon that takes place during the processing. The severity of the cavitation process is mainly dependent on the uniformity of deformation (i.e. level of local thinning) during processing. In the present paper, correlations are made between thickness variations in several formed sheets and the characteristics of the cavities observed in the material. The 1.4 mm thick 5083 aluminum alloy sheets were hot pre-formed at around 450°C for 4 min and then air-cooled. Opto-digital and Scanning Electron Microscopy were used to examine the microstructure and analyse the cavities. Also, grain size measurements were carried out for different location in the SPF formed piece. The surface and volume fractions of the cavities were measured with the aid of metallography image processing (MIPTM) on as-polished samples prior to etching. The results are analyzed in terms of the influence of applied strain and microstructure conditions on the propensity to cavitation of the alloy.

Jan 1, 2015