Search Documents

By S. Banisi, J. A. Finch, A. R. Laplante

"A technique for on-line simultaneous estimation of gas and solids holdup (volume fraction), based on a combination of conductivity and pressure difference measurements, is proposed and tested in a laboratory flotation column (10cm in diameter and 447cm in height). Fundamental concepts underlying this technique and the effect of relevant parameters are discussed. In the studied range, 3-30 %v/v gas holdup and 2-18 % v/v solids holdup, experimental results showed good agreement between the estimated and actual holdup values (as determined by an isolating technique). The relative accuracy of the solids holdup estimation increased when solids density or solids concentration increased. Frequent re-calibration of pressure transducers was found necessary for accurate phase holdup estimation.IntroductionGas holdup is a key parameter in controlling the performance of flotation columns. For example, flotation rate is affected by bubble size and gas rate both of which, in turn, affect gas holdup. Moreover, gas holdup also determines the slurry residence time which indicates a direct influence of gas holdup on recovery.Gas holdup determination has been the focus of many studies (e.g., Castillejos, 1986; Marchese et al., 1992). Some of the techniques which have been used are given in Table 1."

Jan 1, 1994

By Simon C. Dominy, Ian M. Platten, Garry F. Johansen, Alwyn E. Annels, Brian W. Cuffley

Abstract - Coarse gold-bearing veins are characterized by high grades that are localized and erratic. Effective sampling of coarse gold-bearing veins is difficult because of the low concentration and erratic nature of the gold particles. Diamond drilling is an effective measure of geological continuity, however, grade distribution can only be reliably obtained from underground development (including close-spaced sampling, bulk sampling, and trial mining). Comparison between surface and underground drilling, underground linear/panel and bulk sampling indicate that drilling and linear/ panel samples generally understate bulk sample grades. Bulk samples are likely to be the closest estimators of true grade. It is unlikely that anything above an Inferred Resource category can be estimated from surface drilling alone, and at best the grade will only be a global estimate. Underground development, in-fill drilling and bulk sampling/trial mining will be required to delineate Indicated and Measured Resources. Closely spaced development and bulk sampling is likely to be the only way to determine Reserves. The resource estimation process must driven by a clear geological model that should attempt to understand both geological and grade continuity. Traditionally, grade interpolation has been undertaken using classical methods, though more recently, computer-based block modelling techniques have been used with some success. Three case histories are presented, documenting the problems of estimating resources in coarse gold-bearing veins and the practical ways in which they were approached.

Jan 1, 2000

By G. K. Lee, Whaley. H., F. D. Friedrich, I. C. G. Ogle

"IntroductionCurrent coal combustion activities at the Canadian Combustion Research Laboratory (CCRL) reflect the increasingly important contribution that coal is expected to make in meeting our future energy requirements and in reducing our dependence on foreign oil. Widespread use of coal will, however, be heavily dependent on the ability of conventional and emerging combustion systems to cope with the disruptive conflicts caused by variations in fuel quality, on requirements for better equipment availability .and on the implementation of progressively more stringent environmental constraints.To minimize these conflicts, Energy, Mines and Resources Canada has embarked on a systematic sequence of research, development and demonstration- scale (R, D and D) initiatives to stimulate the utilization and competitiveness of thermal coal in both domestic and export markets through a number of complementary in-house projects and external contracts, considered to have short- to intermediate-term benefits to industry and society.Many of the in-house projects are funded in part by industry, whereas the external contracts are either fully funded (100070 government funding) or jointly funded (50% government - 50% project proposer).External contracts and shared-cost projects are an important adjunct to the CCRL in-house effort on coal combustion, because research data can be more effectively transferred to industry and because the commercialization of novel combustion systems can be accelerated significantly."

Jan 1, 1980

By M. Hekmati, M. R. Garmsiri, S. M. Hosseini

"SAG/AG mills have been most common choice in grinding circuits last decades. In the most cases, at the discharge of SAG/AG mills, a trommel screen is used that is equipped with baffles to provide appropriate residence time and improve separation efficiency. Using baffles, with the resultant maintenance requirements could lead to decrease in mill availability. In this research, an innovation in the structure of baffles of a trommel is presented. The results show that using new baffles led to 67% decrease in SAG mill downtime due to problems of baffles and 80% decrease in fine particles on recycle conveyor.INTRODUCTIONComminution is a vital operation in mineral processing circuits and it helps to achieve a certain level of fineness in the ore material. About 60-80 % of the overall energy used in mining is consumed in comminution, and this is the reason that much research has been performed in this field (Kochnev, 2008).During the last decades the configuration of grinding circuits has been changing due in large part to the decrease in the grade of mineral resources and the need for large scale, energy efficient processes. The previous configuration of conventional grinding circuits was based on parallel primary circuits (mostly using ball mill), such as the grinding circuit of Sarcheshmeh concentrator plant no.1 (Figure 1). The new configuration of grinding circuits is based on using SAG/AG mills, such as Shahrebabak concentrator plant (Figure 2), sometimes incorporating new technologies like the HPGR. Nowadays, application of new configuration of grinding circuits using large SAG/AG mills up to 40 feet (Allan, Major, Flintoff, Klein, & Mular, 2006), in the minerals industry is continuing increase due to the significant reduction in capital and operating costs, and increase in the plants throughput (Banisi & Hadizadeh, 2007)."

Jan 1, 2012

By T. G. Joseph

The chicken and egg scenario where adverse truck motions cause ground deterioration and poor ground profiles that in turn cause adverse truck motions is a downward deterioration spiral that dominates in our industry. If we can remove one action, the reaction must stop and vice-versa. A simple 'truck to excavator' load data analysis and wireless communication system is outlined in this paper; that will provide visual assistance to the excavator operator in achieving improved load placement and balance in a truck body. In turn this will reduce the subsequent hauler duty cycle adverse motions and g levels that contribute to structural fatigue, higher tkph, reduced tire life and ongoing maintenance of haul roads

Nov 1, 2011

By Dean Gerhardt

Why the need for proactive loose detection? ?? Past history of ground falls in Saskatchewan mines prompted research into new techniques for ground control. ?? Traditional tools for ground assessment (i.e. visual inspection, sounding with scaling bars) are not proactive and can often be time consuming. ?? Need existed for a system that was non-evasive, time efficient, and could be managed by a single operator. Ground Penetrating Radar (GPR) immerged showing the greatest potential.

May 1, 2008

By Robert B. Parsons

"In all likelihood, Canada's mining industry would be adversely affected by corporate tax reform proposals actively being considered by the Department of Finance in Ottawa. When the next set of proposals for lax reform is released later this year as promised by Finance, the mining industry had better be prepared 10 take a hard look.IntroductionTwo federal budgets ago, in May 1985, Finance Minister Wilson tabled budget papers that were more massive in terms of volume than most federal budgets. Buried in this mass of documentation is a discussion paper entitled ""The Corporate Income Tax System-A Direction For Change"". When the discussion paper was tabled over one year ago, reaction from the business sector was almost nonexistent. By and large, the paper was regarded as nothing more than one more federal publication of mild academic interest.But, recent events suggest that this discussion paper for corporate tax reform could be the cornerstone for a series of changes to the tax laws which would have more profound and widespread effects for all sectors of the economy than any reform since 1971 . No industry in Canada can afford to ignore the movement afoot in Ottawa for corporate tax reform."

Jan 1, 1986

By T. Güyagüler, U. Y. Önder

"This study investigated the psychrometric properties of ventilating air in GAL coal mines. Related measurements were done in underground openings and have been arranged as input data for computer programs prepared for ventilation network and psychrometric analysis.Results obtained from network analysis have been used for psychrometric analysis of ventilating air. Changes in heat and moisture content of air in two major path s between entry and discharge of ventilating air have been investigated. Psychrometric processes occurring in the mine were determined and are shown graphically in Figures 1 and 2. Special attention has been given to determine the changes in psychrometric properties and processes involved in the faces. Results are outlined in this paper.IntroductionThe psychrometric properties of mine air are important factors to mine productivity and efficiency. Therefore, psychrometric analysis should be made for all underground mines; any undesired situation observe d could be corrected by taking the necessary precautions.The analyses were done as a case study for GAL mines, the only mechanized lignite coal mine in Turkey. In this mine, workable reserve is about 300 million tons of coal and yearly planned production is 2.2 million tons. Production is continuing from a coal measure-bed having two coal seams with average thicknesses of 1.52 m and 1.72 m respectively. A 0.85 m shale band exists between these two seams.Two full y-mechanized faces, approximately 220 m long, usually work simultaneously. All measurements, including mine gases and air velocity, are done by sensors connected to a control room by a monitoring system.In the analysis, a line diagram is utilized to described the mine on which every junction and branch is numbered."

Jan 1, 1992

By D. B. Dreisinger, M. R. Tavakoli

Vanadium has been produced from a variety of sources. This metal is known to make aqueous solutions of complex speciation as a function of vanadium concentration and pH. Considering the method of leaching, the impurities in the PLS and the planned vanadium product, different extractants and flowsheets can be applied for solution purification. In this paper, purification of vanadium leaching solution using organophosphorus, solvating and amine extractants will be reviewed. This review will be focused on vanadium separation from iron, molybdenum and uranium which are often present in vanadium resources including primary ores, fly ashes and spent catalysts.

Jan 1, 2014

By Å. Partapuoli, M. Henriksson, P. Wikström, J. Worth, G. Adolfsson

The control of AG mills fed by ores with harder and softer components can be challenging due to the sensitivity of the mill to the ratio of hard to soft components. The mills at LKAB’s iron ore operations are generally well controlled, but there are periods when the throughput falls off dramatically, due to a loss of mill filling. As the ore is upgraded in the sorting plant through magnetic separation prior to milling, this presents an opportunity to manipulate the feed blend in advance. In order to assess this opportunity, a fullscale mill charge was dumped and assayed by size to quantify the build-up of competent waste in the mills. This was supplemented by pilot and locked-cycle laboratory tests at a wide range of feed blends in order to facilitate the development of an appropriate multi-component AG mill model. This paper reports the experimental campaign requirements and methodologies, as well as the major outcomes from analysis and modelling exercises using the industrial, pilot and laboratory multi-component data.

Jan 1, 2012

By J. G. Schofield, C. G. Tan, R. J. Ord

"Most electric furnaces in the nickel and copper smelting industries are still fitted with conventional electrode holders which consist of water-cooled electrical contact clamps and a pressure ring. The water cooling exerts a significant cooling effect on the electrode column. The importance of controlling the temperature of the Soderberg electrode paste at the contact clamp area is examined, using in-plant experience and computer simulation of the paste melting and baking process. In addition to the effect of water-cooling, the effect of other variables, including the mantle air temperature, the electrode current, the furnace freeboard temperature and the electrode slipping rate are discussed. Ways in which the variable heating conditions in the paste melting zone can be controlled are outlined.IntroductionIn most non-ferrous electric smelting operations, the breakage of Soderberg electrodes is an infrequent, isolated occurrence. Occasionally, however, a rash of breakages may be experienced on a particular furnace for what appears to be no obvious reasons. The extent of the breaks may not exhibit a uniform pattern; sometimes the break may be less than half a metre above the electrode tip; at other times it may be at or just below the roof level. The latter type of break is, of course, the most dangerous since it is closest to the non-baked, weak portion of the electrode paste column. No matter where the breaks occur, they result in abnormal furnace power, charging and tapping conditions and loss of production while the new electrode section is slipped and baked. On a six-electrode furnace, breakage on one electrode has the immediate effect of reducing the total furnace power by one-third. On a three-electrode furnace, the effect is more drastic, one half of the power being lost."

Jan 1, 1995

By D. A. MacFadyen, J. J. Brummer, C. C. Pegg

"The first record of a kimberlite found in Canada (1946) was the identification of thin dykes intersected while drilling for gold in Michaud Township, Ontario.Sampling of the Munro Esker (1964) in the Kirkland Lake area, Ontario, by the Geological Survey of Canada identified the occurrence of detrital grains of pyrope garnets along a length of 35 km of the 113 km tested. A search for the source of the garnets resulted in the identification (1968) of a narrow subsurface kimberlite dyke in the Upper Canada Mine. This discovery resulted in a staking rush. Unfortunately, subsequent work did not identify the source of the kimberlite indicator minerals.During 1978 the Ontario Geological Survey started a multi-discipline study of 29 townships (2560 krn2) in the Kirkland Lake area, to encourage exploration for gold, base metals, and kimberlites. Back-hoe sampling (1979 to 1982), where the overburden was thin, and reverse circulation drilling, in areas of thicker drift, yielded samples of the till. These were analyzed for several elements and a mineralogical identification of the heavy minerals was completed. Pyrope and chrome diopside grains were identified.Studies of the Pleistocene geology indicated only the most recent direction (167 degrees) of ice advance (Matheson) and the associated deposits, out of a possible three advances known to occur in the general region straddling the Ontario-Quebec boundary, is present in the immediate area of Kirkland Lake. Contouring the distribution of pyrope grains (1990) showed a concentration centered over an area of 616 km2 extending down-ice from Gauthier Township. This included a smaller area containing chrome diopside grains. Kimberlite boulders were identified (1981) in gravel pits on the Munro and Misema River Eskers located within this anomalous area. The next step would be to use the airborne geophysical data to locate the kimberlite pipes which yielded the indicator minerals and boulders. The source area is likely to be in the northern half of the Ontario Geological Survey study area."

Jan 1, 1992

By Helen Morrison, Chris Staun, James Vaughan

"Mercury is introduced into the Bayer refining process as a trace element in bauxite. During the digestion stage, a portion of the mercury is extracted which partitions between the flash tank off-gas, vapour condensate and bauxite residue streams. A technology or treatment that stabilises mercury in the solid phase during digestion would prevent environmental management issues that may arise from the presence of mercury in condensate and non-condensable gases. This study examines the effect of process additives on the deportment of mercury under Bayer digestion conditions. Bauxite digestion experiments were conducted in batch autoclaves in the presence of additives. Process liquor was analysed for mercury content using a thermal desorption technique. Pyrite and copper hydroxide were evaluated for their suitability as additives.INTRODUCTIONMercury is an ancient metal characterised by electrochemical nobility, volatility, low solubility in water and a liquid state at room temperature (Holleman and Wiberg, 2001). The biogeochemical cycle of mercury is complex. Elemental mercury may enter the atmosphere due its volatility, where it can be transported long distances. After settling and adsorption to sediments, methylation is catalysed through microbial metabolism (Qureshi et al., 2009). Methylated mercury species are potent neurotoxins, and bioaccumulation of mercury is well documented, particularly in seafood (Kozin et al., 2013, Pan et al., 2014, Pollman, 2014). Environmental regulations for mercury emissions are becoming increasingly stringent (UNEP, 2015). Considerable research has already been performed and technologies developed for the remediation of mercury in wastewater and the trapping of mercury from industrial stack emissions. Wastewater technologies usually target ionised mercury using adsorbent, ion exchange and complexation mechanisms (Krishnan and Anirudhan, 2002, Li et al., 2015a, Chiarle et al., 2000), while stack emission technology is dominated by impregnated activated carbon adsorbents (Gao et al., 2013, Zheng et al., 2012). Related developments include piezoelectric amalgamating sensors for in line detection of gaseous elemental mercury in industrial stack emissions (Kabir et al., 2015, Sabri et al., 2011). There is a paucity of research regarding removal of mercury from the Bayer process."

Jan 1, 2016

"This paper describes an alternative method of vehicle control which uses a micro-processor to control the field current and armature voltage concurrently. The field tests carried out and the conclusions drawn from the basis of the paper.IntroductionIt is generally accepted that the main obstacle to a greater use of electric vehicles is the relatively poor range and performance when compared to alternatives such as diesel and petrol-engine vehicles. Much effort has been applied to the problem of increasing the energy storage density of batteries and considerable improvements are now being reported.Improvements in the efficient use of the stored energy, although unlikely to achieve the necessary increase in range and performance for a widespread acceptance of electric vehicles, can nevertheless make a useful contribution. Because the improvement in efficiency is achieved by a reduction in losses, it follows that the temperature rise in drive-train components is reduced. These advantages, coupled with the increasing cost of energy, make improvements in the efficient use of the stored energy desirable, if not absolutely necessary. To achieve this with the large and rapidly varying loads encountered during the operational use of a vehicle will require a more flexible system of control than that provided by the current limit. This paper describes an alternative method of control which uses a micro-processor to control the field current and armature voltage concurrently.The value of these parameters is selected to supply the power demand at the motor shaft, with the minimum losses in electrical transmission, thus increasing the efficiency with which the stored energy is used."

Jan 1, 1982

By F. Logsch, H. Pempel, J. Markowski, P. Ay

"Due to the European Directive 2000/53/EC on end-of-life-vehicles, from 2015 on more than 95% of car materials have to be recycled. In order to recycle the materials back into the economic cycle, it is necessary to produce products with high quality and purity.Plastic components in cars, which are coated with metals by vapour deposition or electroplating, have a wide circulation (e.g., as cladding panel or trim strip for interiors and exteriors). In the end-of-lifevehicle recycling process, these plastic-metal composites are not considered in usual technologies (car shredder) and are not separated from Automotive Shredder Residue. These parts can be separated by optical or HF-detection sorting and then introduced to a specific treatment.Experiments with a specially developed bioleaching configuration showed that the thin coatings, which consist mainly of copper, nickel and chromium, can be removed efficiently from the polymer base materials by a bioleaching solution with Acidothiobacillus ferrooxidans as a leaching agent. The solution used was produced in special fermenters with a 9K-nutrient salt media. During the bioleaching process at 35°C maximum temperature, most of the copper is dissolved and the other metals accumulate as metal sludge. The bacterial cultures based on A. ferrooxidans are robust and resilient.After a 48-hour bioleaching period while the composites were stirred regularly with ventilation, the plastic particles were completely free from metallic coatings. The metal components are separated for further use: undissolved components (mainly Ni and Cr) are separated by decantation of the solution; dissolved copper recovey is carried out by cementation of copper. The cementated solid contains ~98% Cu, along with small amounts of other metals.With the bioleaching process, good separation and re-utilization of the metallic coatings is possible. The cleaned plastic parts were prepared by compounding for new applications with injectionmoulding."

Jan 1, 2016

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The major importance of liners in grinding is their role in providing an appropriate trajectory for the charge. Since it is not possible to study the charge movement by direct observation in operating industrial mills, this task is accomplished by physical (laboratory), and/or, mathematical (software) methods. Because of the high cost and a longer time required for a physical analysis, mathematical simulations have become more common. Simulation of the effect of liner shape on the charge movement has provided a means to select a proper design based on the operational objectives and conditions. Furthermore, the liner shape changes due to wear and impact during operation, which will influence the charge trajectory. This adds more of an incentive to use simulation. These changes in liner could be predicted through liner profile measurements during operation and/or simulation. In this research, an inhouse developed DEM software called KMPCDEM © was used to simulate the charge movement in industrial plant SAG mills. A geometrical method of implementing the shell liners on SAG mills at the Sarcheshmeh (9.75×4.87 m) and the Gole-E-Ghohar (9×2.05 m) operations facilitated the software simulation. Point by point implementation of the measurements of liner profiles of these mills enabled the study to trend the change in the charge movement as the liners wear. Comparison of the simulation to a laboratory mill (1 m diameter) showed that the difference between the measured and predicted charge impact point, shoulder angle and toe angle were 6, 4 and 3°, respectively.INTRODUCTIONComminution is the most energy intensive operation constituting the major portion of operating and capital costs of a mineral processing plant. In the last decade, a vast number of research was aimed at studying various aspects of grinding with the aim of performance improvements (Davis, 1919; Mishra & Rajamani, 1990; kalala, Breetzke, & Moys, 2008). Mill liners transfer the input power to the charge and play a significant role in affecting the motion of the charge (Mclvor, 1983; Mishra & Rajamani, 1990; Radziszewski, 1997; Van Nierop, Glover, Hinde, & Moys, 2001; kalala et al., 2008). Lifters are usually used with mill liners to extend their life and to enhance the grinding and impact breakage efficiency. Mill lifters are used to raise the grinding media and ore to transfer the energy from the mill to the load (Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010)."

Jan 1, 2016

By P. A. Studemeister

"A trondhjemite stock intrudes a volcanic sequence that has massive sulphide lenses and that is metamorphosed to the greenschist facies at Gutcher Lake, 25 km north of Wawa, Ontario. The stock is 4 km2 in plan and is partly enveloped by an aureole of chlorite-epidote-amphibolehornfels up to 1 km wide. Within this contact aureole, biotite is partly pseudomorphosed by chlorite;epidote and hornblende are mottled by chlorite, calcite, plus quartz; albite has 0% An to 8% An; and hornblende porphyroblasts have actinolite rims. The stock has chlorite pseudomorphous after biotite; and feldspar is mottled by white mica plus calcite and has a clear rim of albite. Fractures filled with quartz, calcite, ankerite, chlorite, white mica, pyrite, and native gold cross-cut the stock and its hornfels aureole. These gold-bearing veins are enveloped by foliated rocks with quartz, calcite, white mica, and chlorite that grade outward from the veins into trondhjemite or hornfels.The stock, emplaced into a submarine volcanic series, emanated heat that caused seawater to convect and formed a contact aureole of hornblende hornfels. The stock eventually intruded its aureole and this culminated with regional metamorphism to the greenschist facies. Regional metamorphism hydrated the stock and its hornfels aureole. Native gold precipitated with quartz along fractures from metamorphic flu ids in response to cooling and wallrock hydration. exploration for this type of gold deposits should focus around felsic intrusions that have albite and that have contact aureoles retrograded by regional metamorphism."

Jan 1, 1985

By A. LA. Salama, D. B. Hyma

"The Western Research Centre (WRC) of CANMET located in Devon, Alberta, is a modern research facility offering services ranging from fundamental research to pilot plant investigations. Recently, a 0. 76 metre diameter by 7.9 metre high Flotaire column flotation cell was installed as a demonstration unit for Canadian coal producers. Because the column cell is intended to be used for research, development and demonstration, WRC recognized that additional sensing equipment and improved process control would be required to generate good data for subsequent column scale-up and engineering design.A low cost, personal computer based control system was, therefore, designed and installed. This paper describes the stepwise procedure in developing the control strategies, selection of system software and hardware, and installation and configuration of the system.Preliminary performance data on a western Canadian coal sample are also presented. Future testwork is planned on additional coal samples to expand upon existing database."

Jan 1, 1993

Purpose of TSUG Continuous Improvement in Mining Share Best Practises Exchange Ideas Network for Frontline Supervisors and Middle Management Meetings ? Two per Year -Spring and Fall ? Thirty Five to Forty Attendees ? Rotate Between Host Properties ? Host Mine Provides ? Meeting Room for One Day Tour of Mine and Maintenance facilities on Second Day

May 1, 2010

By Frank Mucciardi, Louca Gourtsoyannis

"Low and inconsistent recoveries of aluminum in the production of aluminum-killed steels triggered an extensive research program on the aluminum dissolution kinetics at McGill University. This research program led to the understanding of the melting kinetics and the hydrodynamics of making additions to liquid steel. It showed the necessity of gradually releasing liquid aluminum at the bottom of the ladle to increase aluminum recoveries.This knowledge was verified in practice at Sidbec-Dosco, where a prototype aluminum wire injector was developed and installed for the first time in Canada. The industrial application showed the validity of the theoretical and experimental results and provided further data for the mathematical modelling of the process.The development of the theoretical understanding, the industrial results, and the interaction between university and industry are presented.IntroductionAluminum is an extremely effective deoxidizer of molten steel; nevertheless, an efficient method of adding it to steel has eluded steelmakers for many years. It is well known that the recovery of aluminum used in the production of aluminum killed steel is both low and eratic, especially when the aluminum is added in the form of bars or lumps from chutes into filling ladles, a practice still common in many of today's steelmaking operations.As the density of aluminum is only about 40010 that of molten steel, it is conceivable that loose bars of aluminum simply ""thrown"" into a filling ladle will resurface before any appreciable dissolution of the aluminum has occurred, particularly if the depth of penetration of the additions is small. Before one can conclude that this is indeed the case, it is necessary to know the melting kinetics of an aluminum addition. Back in 1972, this information was not available; hence an extensive research program which focused on melting kinetics was initiated at McGill University."

Jan 1, 1982