Search Documents

By Edward Sampson

Bases of National Power At a time when the economy of the world is in a particularly troubled state it is appropriate to examine some problems of the distribution of natural resources. I should like particularly to call attention to the remarkable increasing demand for natural resources, to give an analysis of the demand for certain mineral resources, and to direct attention to some problems in satisfying this demand. All industrial power is based on natural resources and the most basic of these are soils, energy resources, and mineral resources. There is a strong interrelation of these resources, more than is obvious, and I shall take up certain aspects from the point of view of a geologist. Few nations are well endowed with all three of the kinds of natural resources I have mentioned and much has been done by some small countries whose peoples are industrious and enterprising and where conditions for free world trade have been favourable. However, major industrial power is dependent on a substantial endowment of all three classes.

Jan 1, 1949

By J. Jung, W. Keller, N. Rohn

In hydrometallurgical minerals processing slurries are often processed at very small grind sizes and high solids concentrations. This normally results in flow anomalies of such slurries. Due to flow limits or yield stress the slurry tends to stagnate close to the vessel bottom, the walls and at any internals. The main mixing task therefore generally is not suspending of the solids but the homogeneous blending of the entire vessel volume. If not considered during the agitator design only a fraction of the vessel contents will be mixed. Therefore the knowledge of the slurry rheology as well as the variations in process parameters is vital to design e.g. storage or surge tanks. The integral mixing solution considers the motor power, the choice of the impeller type and number, the impeller diameter as well as the design of the baffles and feed and discharge positions.

Jan 1, 2014

By Lawrence Melis

Fission Uranium Corp.’s Triple R Uranium Deposit at its Patterson Lake South Project is located in northwest Saskatchewan in Canada’s Athabasca Basin. As part of pre-feasibility studies for the project a detailed metallurgical test program was completed to provide process design criteria. The testwork program encompassed preparation and analysis of test composites, comminution testing, uranium acid leaching, liquid-solid separation, solvent extraction of uranium, precipitation of uranium yellowcake products, tailings and effluent treatment, tailings physical and chemical characterization, and environmental testing of prepared tailings, as well as investigations of gold and silver recovery from the mineralization. The paper provides mineralogical information, testwork methodologies and test results which were used to arrive at process design criteria and the selection of the process flowsheet for the project.

Jan 1, 2020

"Mining with blast holes drilled upwards may be done to recover sill pillars, or for economic reasons when the distance between the levels is relatively large. If the rock is sufficiently competent to accommodate large stope size, the distance between sublevels could be increased to as much as drilling accuracy allows. The same drill drift can be used for the drilling of both down holes and up holes. In the case of down holes, the initial opening of the stope (drop raise) is not as much a problem as for the inverse drop raise for mining with up holes. This is because, with a drop raise, a lot of space is available at the toe for the blasted rock to expand. In addition, the raise can be blasted in many shots, thus allowing smaller blasts each time. Inverse drop raises are generally much more difficult to blast because of the limited space for muck flow, and must, therefore, be taken down in a single blast, requiring special considerations in order to ensure a success. A case study of a 29 m (95 ft) inverse drop raise successfully blasted in a single shot at Heath Steele Mines is described. The paper covers technical considerations such as drilling accuracy, hole deviation survey, delay extension and protection, initiation methods and initiation sequence. Finally, a novel method for creating the initial opening called ’slot drilling’ is presented. This method, inspired from LKAB in Sweden, consists of drilling a row of interconnected holes using a special guide mounted on a regular production drill hammer.With a case study of blasting an inverse drop raise of 29 m (95 ft) in one blast, this paper further discusses some technical issues that are critical for the development of inverse drop raises. A novel method for creating the initial opening with a slot of interconnected holes is also presented with the experience acquired at different mine sites across the Noranda group."

Jan 1, 2000

By R. Matusewicz, A. Kaye

Ausmelt Top Submerged Lancing (TSL) Technology has gained widespread commercial acceptance in non-ferrous applications, including the processing of lead and zinc primary concentrates and secondary (post-consumer) materials. TSL is highly flexible and efficient, and is one of the few technologies which can process primary and secondary feeds, and use varying fuels, to deliver high recoveries and excellent environmental performance. With the recent high value of both lead and zinc, and an escalating awareness of the sustainable use of resources, focus on the processing of secondary feed material sources has surged. Ausmelt Technology has proven to be well suited to the economic recovery of values, with twenty-two (22) Ausmelt furnaces processing lead and zinc bearing feed sources now in operation, under design or construction. This paper describes Ausmelt's progress in the fields of lead and zinc processing, and developments in new processing areas such as EAF dust processing and linking to innovative hydrometallurgical technology. Ausmelt has recently committed to the Whyalla Zinc project as the owner/operator of a facility for the treatment of zinc bearing secondary feeds. This project is due for start up in the first quarter of 2008.

Jan 1, 2008

By Yoginder P. Chugh

This paper discusses an ongoing field study in southern Illinois (USA) that focuses on: 1) Identifying mechanisms of instability in the set-up rooms (SR) and their T-junctions with headgate and tailgate entries, 2) Developing alternate 3-entry and 4-entry set-up rooms geometry using 3-D numerical analyses, 3) Implementing developed geometries in cooperation with mining professionals and regulatory agencies, and 4) Demonstrating performance of implemented geometries through field monitoring. Illinois longwall mining operations typically experience ground control problems (roof falls, rib sloughing, floor heave, etc.) within SR layouts and around the T-junctions of SR. These occur around the areas where the SR for adjacent longwall face (to be mined) connect with the SR of the previously mined face, and around the tail-gate entries of the mined-out longwall face and around the T-junctions of SR. The problems manifest as highly fractured immediate roof strata, major shear zones in the roof, horizontal displacements within the excavations that result in shearing off the heads of the bolts, floor heave and severe rib sloughing. Similar observations have also been made in longwall mining in Utah.

Aug 1, 2013

By R. Cammack

"A fundamental component of the Hoek–Brown empirical rock failure criterion is assessing an appropriate mi constant. In developing their empirical criterion Hoek and Brown normalised triaxial test results by dividing the principal stresses at failure by the uniaxial compressive strength to provide mi values for typical rock types. Experience shows that Hoek triaxial tests for individual lithology types commonly have a large inherent scatter. In addition, tests are often conducted on core from random locations, which although being of one parent rock type, display variations in density as well as minor variations in grain size and alteration.This paper presents experience from projects the authors have been involved in which large sample populations of triaxial and UCS tests on similar rock types were available. Geophysical logging data was also available for some projects. The methods used to estimate the compressive strength for each sample and the effects on normalising the data sets are described. The variability of the data and uncertainties and assumptions involved in the process of assigning a mi value from the normalised data are also discussed."

Jan 1, 2015

Several inorganic reagents and organic polymers were tested as depressants in the single mineral flotation of ultrafine iron oxide and hydroxylapatite with Dowfroth 250 as a frother. It was observed that the inorganic reagents and the low molecular weight polymers generally caused dispersion of the ultrafine particles, and consequently their recovery into froth products more or less equaled the recovery of water. On the other hand, the high molecular weight polymers caused different degrees of flocculation of the ultrafine particles, and their recoveries were much lower than the recovery of water. These observations pointed to a need to re-define flotation depressants in fine particle flotation. The traditional definition of a flotation depressant, i.e., to make particle surfaces hydrophilic by forming a hydrophilic film and/or by removing collector and activator coatings, is sufficient for relatively coarse particles. However, to prevent fine and ultrafine particles from floating, a successful depressant should not only make the particles hydrophilic, but also enlarge the particle sizes so that they do not enter the froth product by mechanical entrainment. Polymeric depressants are ideal for these purposes. The different schemes to use polymeric depressants in the selective flotation of fine and ultrafine particles were discussed These schemes involve the integration of the polymeric depressants into other size enlargement processes such as shear flocculation, oil agglomeration, etc., for hydrophobic particles.

Jan 1, 2004

By P. B. Queneau, Peter V. Avotins, Lauch F. Farris

"The Lang Bay germanium property is a carbonaceous sandstone deposit outcropping near the Pacific coast, 100 km north of Vancouver. The germanium-bearing seams are up to 5 m thick. Where one such seam outcrops, it averages 50 to 60 g Ge/tonne. Drill core analyses have shown considerably greater concentrations of germanium at depth. Additional drilling to establish continuity and grade of the germanium-b earing strata is scheduled for 1986. The germanium occurs in association with lignite, which makes up 1 to 2% of the seam. American Cyanamid Company engineers have developed a proprietary flotation reagent effective for concentrating the germanium rich vitrain portion of the Lang Bay lignite. Ongoing laboratory studies are developing procedures for further upgrading and refining of this germanium. This paper outlines progress made by Fargo Oil Corporation on Lang Bay geology, reserve estimation, mine planning, ore dressing, refining, and economic evaluation.IntroductionIn 1871, Mendeleyev specula ted on the properties of a ""missing"" element between silico n and tin on the periodic table. The discovery of germanium fifteen years later proved the Mendeleyev predictions to be remarkably accurate. Almo half a century later, the pioneering work of McCutcheon of Eagle-Picher led to production of germanium dioxide from Oklahoma zinc smelting residues. Demand for the element surged due to development of the Ge02 diode rectifier during World War II, followed by development of the transistor in 1947. The chief commercial sources for germanium during the following two decades were the Cu-Zn mines in the Congo and the Zn-Cu-Pb mines of Tsumeb in Southwest Africa. The germanium was chemically combined in complex Cu-Fe sulphides (germanite and renierite), from which the element was recovered either by leaching the selectively roasted sulphide, or by direct fuming of GeS(I). Although these deposits have reportedly been depleted (2), new deposits of renierite have been discovered in Zaire. Alternative sources of germanium are therefore being sought worldwide for use in infrared optics, semiconductors, fibre optics, and catalysts. One such source is germanium-rich coal (2)."

Jan 1, 1986

By J. R. Rau

While refuge chambers are common place in most underground mining projects, there are different philosophies as to what life support systems are to be considered and how these systems are to be applied. Case studies in the underground mining industry have examples of emergencies where the external compressed air and power supply to the refuge chamber were compromised due to proximity of services to the fire location. In 2005, The Department of Industry and Resources, Western Australia, drafted guidelines that listed specific requirements for refuge chambers which included a secondary life support system that would operate independently of external sources. The objective of this document is to examine what critical life support systems are essential for safe entrapment in the event of an emergency and to examine considerations for their application.

Aug 1, 2013

By M. R. Coffin

Since the plant startup in 1972, the leaching and jarosite precipitation circuits at the zinc plant of the Kidd Metallurgical Division have been reconfigured several times to improve overall performance, and/or to respond to market conditions. For the most part, the circuit changes have been driven by two market factors: the price of zinc and the price of silver. Until recently, circuit modifications undertaken to improve zinc extraction and recovery came at the expense of silver recovery, and vice versa. In 2004, the plant was modified once again to produce a precious metals-bearing residue, but additional leaching circuits were added to ensure that zinc extraction and recovery did not suffer as a consequence. The development of the zinc plant of the Kidd Metallurgical Division is updated in this paper, with a focus on the recent circuit modifications and associated control strategies that were implemented to maximize zinc and precious metals recoveries, and control the quality of the jarosite residue.

Jan 1, 2006

By B. Qiu

The large surface ground movements induced by underground mining could threaten the safety of the pipelines laid across the subsidence-prone area. Existing analytical methods for the stress analysis of buried pipeline over mine subsidence area were based on the assumption of ?thin? pipeline, which limited their applicability. This paper presents the improved model with the capability to determine the stress distribution of the ?thick? pipeline. The pipe-soil interaction in this model was also updated to adapt various pipe soil contact conditions. In addition, the time-dependent effects of dynamic subsidence effects were also added to the model. A case of protecting a long section of a buried large-diameter pipeline over two longwall panels in a shallow mine is shown. The stress distribution along the pipeline is determined and the overstressed sections are identified. A partial uncovering plan was developed based on the predicted stress and complicated terrain at the site.

Aug 1, 2013

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970

By A. Desbiens, R. del Villar

"This two-part paper summarizes the design and implementation of a distributed PIbased control strategy installed at the B grinding circuit, at the Kidd Creek Division of Falconbridge Ltd. Part I details the design of the control strategy using a grinding circuit dynamic simulator (DYNAFRAG). The first step consisted of sampling campaigns and data processing to calibrate DYNAFRAG. Then, several control alternatives were designed and tested with the simulator. The main feature of these strategies is their ability to regulate or keep within an upper and lower limit five output variables (circulating load, rod mill density, cyclone feed and overflow densities and pump box level) with only three manipulated variables (rod mill water, pump box water and rod mill tonnage). By simulation on DYNAFRAG, it was possible to discriminate among several control structures. The preferred control strategy uses a saturation algorithm, which allows the adequate regulation of two measured variables with only one actuator. Controllers located in interacting loops are appropriately tuned, taking into account the existing process coupling. Part II will present the implementation of the selected control strategy.IntroductionSteady state simulators are used to predict the stationary state of a given process under specific operating conditions. Tradi - tionally, steady state simulation has been applied for process flowsheet design, for evaluating process modification benefits or for determining key operating parameters in process operation optimization. Dynamic simulators add a new dimension to process simulation since they allow the prediction of the process transient behaviour, resulting from the application of a different set of operating conditions and/or from natural disturbances or equipment failure. Dynamic simulators can also be used for the training of new operators or for the design of control strategies."

Jan 1, 1997

By H. Kim

"IntroductionThe Hat Creek coal field contains low-grade coal deposits which are the thickest in the world. The diamond drilling and geophysical surveys conducted by B.C. Hydro over the last six years have indicated in excess of 2 billion tonnes of sub-bituminous to lignitic coal. The coal field is in the Interior Plateau Dry Belt, about 240 km northeast of Vancouver, and contains two explored, nearsurface coal deposits amenable to surface mining (Fig. I). The No. I deposit contains approximately 740 million tonnes of coal at 17.71 MJ / kg, or 7,600 Btu/lb, at 34.82% ash and 24% moisture. The No. 2 deposit to the south contains appreciably more coal resources at somewhat lower grade, but it has not been explored so extensively because of its higher stripping ratio. Therefore most of the exploration activities to date have been directed toward the development of the No. I deposit. The No . I coal deposit has been selected as the source of fuel for a proposed thermal powerplant to be built about 5 km east of the deposit. The purpose of this paper is to summarize the data obtained from the diamond drilling and the geophysical logging in the No. I deposit between 1974 and 1979. An attempt is made to explain the depositional environment of the Hat Creek coal measures. Because the understanding of the depositional environment in.a particular basin is essentially an evaluation of all the geologic properties of the area, the available geological information in the No. I deposit has been compiled on the basis of consistent criteria. This includes data on the lithology of the coal measures, thickness and areal distribution of the elastic sediments, and on the changes in the megascopic stratigraphic profile based on geophysical correlation. The palynopetrographic relationship and detailed sedimentological aspects are not examined in this paper. Such studies should provide important information relating the causal vegetal and chemical responses of the coals to -environmental changes. Extensive deposition of surficial materials during de-glaciation left most of the area of the Upper Hat Creek Valley devoid of bedrock exposures. Structural and stratigraphic features are hidden beneath glacial deposits and/or post-Eocene volcanics. As a result, the geological interpretation of the Hat Creek coal basin has been based primarily on drilling and geophysical data. Because of this, any explanation of the depositional environment details is tentative until the deposits are stripped for development."

Jan 1, 1985

By O`Donnell. P. J.

THE modern coal cutter is a highly developed, and to a certain extent a somewhat complicated, machine. The requisite power to cope with conditions as found must be generated by the motor with due regard to limitations in the matter of dimensions and weight. This imposes the necessity of relatively high speeds of rotation. Any factor external to the machine proper which tends to reduce the load on the motor and gearing is most important. Experience has proved that close attention to the question of cutter-chain details undoubtedly results, in practically every coal-cutting operation, in increased efficiency and reduction of power and maintenance costs. The chain is the unit of the coal cutter which most greatly affects the economical operation of the machine, and only by due consideration of conditions and by the proper selection of the right chain can best results be expected; also, intelligent care of the chain while in operation is essential if it is to give its best service. The chain is the part of the machine that carries the pick boxes or blocks, which are connected to each other by a pair of chain links. The power to drive the chain is trans-mitted by a sprocket. The chain runs in guides supported by a rigid member called a 'jib'. Figure 1 shows the various parts mentioned. The first requirement of a chain is that it cut the coal as fast as possible. The second is that it do so economically. Economy of cutting can conveniently be divided as follows: (1) Economy in power used. (2) Economy in pick life. (3) Economy ' in chain life. ( 4) Economy in jib life. (5) Economy in labour for maintenance.

Jan 1, 1936

By G. V. Theja, V. B. Maji

Large infrastructure projects like tunnel excavations, underground constructions face innumerable risks. For successful completion of these projects, it is essential that we foresee and understand risks that could occur during different phases of the project. One of the risks affecting underground excavation projects is the inaccurate performance prediction of TBMs. As this could severely affect the project, resulting in lower advance rates and could also result in changing the excavation machine or method, due to difficulties in excavation, thereby increasing the overall cost of tunnelling. This makes performance prediction of the TBMs as one of the crucial aspects in tunnelling, as a precise estimation of its performance is required for planning and estimation of time and cost of the tunnelling projects. This performance prediction of TBM is a challenging geotechnical problem that is intricate and complex in nature, this is possibly due to the fact that TBM performance prediction involves understanding the rock fragmentation process in wide range from micro-scale (i.e. the interaction of surface of rock material and cutter tip) to macro-scale (including the interaction of rock mass and TBM). Thus in order for the performance prediction model to be efficient, parameters of both TBM specifications and ground conditions have to be considered. Various models have been proposed by researchers since the early phases of TBM application, these studies resulted in the development and improvement of numerous penetration prediction models. Most of these models consider the geotechnical parameters that are input to the model to be consistent along the TBM drive and neglect the uncertainties in parameters that occur. And so to improve the predictive capability of these models and to incorporate the above uncertainties, the penetration rate is modeled as a stochastic variable depending on the geotechnical and TBM parameters, its statistical distribution is determined and is used to characterize the penetration rate instead.

Jan 1, 2015

By Roy S. Celland, K. H. Singh

The introduction of 'post' pillar mining at the Strathcona mine represents a new approach to ground support in cut-and-fill applications. The method has also shown significant economic advantages. It is believed that the development of this concept is one of the few examples where rock mechanics principles have successfully been applied in the development of a stoping method. The paper describes the evolution of this method and contains discussions on the theoretical analysis of the technical, operational and economics aspects of the system. Pillar design procedures and field observations on the practical application of theoretical analysis are also outlined.

Jan 1, 1973

By Harry V. Warren

THE Dolly Varden Mine is situated in the Kitsault River valley, eighteen miles from the head of Alice arm, in the Nass River mining division of British Columbia. During the years 1919-21 it was operated by the Taylor Engineering Company, Limited, and produced 1,300,000 oz. silver from about 36,000 tons of ore. The ore was transported by narrow-gauge railway to Alice arm, and shipped to the smelter at Anyox for treatment. During recent years, a small quantity of high-grade ore has been extracted by leasers and shipped to the smelter at Tacoma, Wash. Unfortunately, the bonanza ores which occurred near the surface did nor persist to depth, and two hundred feet below the exposures only rare and unimportant patches of ridi ore have been found. Two opinions exist as to the origin of this rich silver ore. One, advanced by V. Delmage (1, 2), is that the ores are hypogene, and the other, by G. Hanson(3, 4, S), is that the ores are the result of supergene enrichment. It is true that Dolmage first advanced his view that the ores are primary because they appeared to be analagous to Premier ore, which he had studied in detail and which he considered to be primary. The present authors have had access to excellent suites of material from both mines and consider the comparison well taken, the only essential mineralogical difference being the presence at the Premier mine, in addition to the silver minerals, of gold and electrum. Although the arguments put forward by Delmage have, in the opinion of the authors, never been refuted, nevertheless R. P. D. Graham(6), in a reference to the mine published in 1924, describes the ore as of supergene origin, and since then nobody appears to have challenged this statement. Indeed, in 1935, Hanson re-affirmed his earlier conclusion(5).

Jan 1, 1942

By D. P. R. Smyth

The limestone reef reservoir at Swan Hills consists essentially of a "buildup" of successively smaller atoll-like layers. Precipitation of calcium carbonate within the lagoonal area of each layer essentially kept pace with growth of the outer organic lattice. Within the reef mass, six de-positional environments characterized by specific suites of fossils (or fossil fragments) and associated limestone textures are recognized as follows: ( 1) Aerated moderately agitated water of normal marine salinity (widespread shelf or submerged reef-built platform). Thamnopora-type corals, Amphipora, "pancake" stroma-toporoids, crinoids, articulate bra-chiopods, rare rugose cup corals, and ostracods occurs in light gray-buff skeletal microgranular limestone of low permeability. (2) Semi-stagnant quiet water of normal marine salinity (leeward side of reef). Crinoids, articulate brachio-pods, rare thamnopora-type corals, Amphipora, pancake and bulbous stromatoporoids, rugose cup corals, ostracods and gastropods occur in impermeable dark brown argillaceous skeletal calcilutite with thin black bituminous shale beds and rare dark chert nodules.

Jan 1, 1961