Search Documents

By John Vergunst

"This paper traces the development of Ontario 's cap lamp standard. Over the years, numerous Coroner's Juries investigating fatal mine accidents have made recommendations with respect to underground lighting. As well, recommendations to improve mine lighting have been made by two Commissions, investigating mine safety in Ontario.During the past few years, the performance of any cap lamp worn by miners involved in serious accidents, have been measured by the Mining Heal/h and Safety Branch. Large variations in light output were found between and among cap lamp types. These variations have been attributed to the lack of quality control on the bulbs, design of the cap lamp head piece and in some cases, poor maintenance.In 1986, a series of underground tests were conducted to establish the minimum light output from cap lamps required to visually identify loose ground. The results of these tests indicated that a cap lamp should produce a minimum peak illuminance of 1500 lux measured at 1.2 metres from the light source. On May 30, 1987, Ontario became the first province in Canada to legislate the minimum amount of light required to visually assess ground conditions. INTRODUCTIONPoor lighting has been identified as a factor which can contribute to mining accidents. Over the past decade, several Coroner's Juries as a result of inquests into mining fatalities, have recommended improved lighting in mines.The Joint Federal-Provincial Inquiry Commission into Safety of Mines and Mining Plants in Ontario, was appointed to report upon the adequacy of existing arrangements and practice s that may affect safety. This Commission completed their report in April 1981, and recommended that inadequate lighting be investigated as a possible cause of all reportable underground accidents, and that a comprehensive research programinto mine lighting be undertaken.In response to the first recommendation, the Mining Health and Safety Branch of the Ministry of Labour, hereafter referred to as the Branch, initiated a program to measure lighting levels in all fatal accident investigations where inadequate lighting was a possible factor."

Jan 1, 1989

By Xiaozhu Chen, Qi Ping, Pu Yuan, Qinyong Ma

"In order to investigate the fractal feature of coalmine deep rock fragments under impact loads, variable cross-section split Hopkinson pressure bar apparatus, 50 mm in diameter, was adopted to conduct impact compressive test for rock specimens from -962m deep coalmine. Various impact pressures, such as 0.3, 0.6, 0.9 and 1.2MPa, were selected to implement different loading rates. Sieving statistical analyses were conducted for rock fragments after being impacted, and the particle size distribution of broken rock in various loading rates were calculated with the fractal method and then the corresponding fractal dimension was obtained. Test results shows that there is a good self-similarity and fractal feature in fragments distribution of deep coalmine sandstone under impact loads. The fractal dimension of fragments is between 1.9 and 2.7. The research also indicates that there is an approximate power relationship between dynamic compressive strength and fractal dimension, and a strength power relationship between fractal dimension and average strain rate. Moreover, there is a linear relationship between fractal dimension and specimen absorbed energy. The rock fractured process can be quantitatively described through fractal dimension, which can reflect the deep rock broken degree and is an ideal index to evaluate the distribution of rock fragments.INTRODUCTIONBroken rock is one of the most basic processes in mining operations, rock fragmentation has always been an important index to evaluate rock breaking effect (Xu & Yu, 1984). Macroscopic fragmentation of rock material is the final results of continuous development, expansion, gathering and cutthrough of internal micro-cracks. This process, developing from microscopic damage to macroscopic fragmentation, is an energy dissipation process and shows fractal characteristics (Xie, 1993). Turcotte (1986) has conducted statistical analyses of fragmentation for different kinds of geological materials under various broken conditions, and arrived at the conclusion that fragmentation distribution is a fractal."

Jan 1, 2015

By A. G. Roach

Introduction The plant described in this paper is located at Coniston, Ontario, the smelting centre of the former Mond Nickel Company. Coniston is situated some eight miles east of Sudbury on the main line of the Canadian Pacific railway and on the Toronto-Capreol branch of the Canadian National-railways. The plant is now under control of the International Nickel Company, as a result of the merger of the two companies in 1929. The smelter proper includes four 50-in. by 240-in. blast furnaces and five 13 ft. by 30 ft. converters, and has a capacity of about 65,000 tons of ore charge per month. As accessories to the smelter there are a mill, where some 10,000 tons per month of low-grade ores are concentrated, and the sintering plant, which is the subject of this paper. The present 6-unit sintering plant replaces a former 4-unit installation. Here, fine ores, concentrates, and flue-dust are sintered on Dwight-Lloyd machines, the sinter produced being charged into the blast furnaces. At the time of writing (1931), only the concentrator is operating at capacity, due to present world conditions.

Jan 1, 1932

By M. B. Kime

"Discrete-element method (DEM) modelling is a powerful tool for studying particulate systems within the mineral processing industry. DEM simulations were conducted to investigate the power draw, load behaviour, and impact energy profile of an experimental ball mill under different milling conditions. The variables considered were mill rotational speed (percent critical speed), ball size, and lifter face angle. The simulation results indicated that the grinding efficiency would be enhanced by using 80% critical speed, 30 mm ball diameter, and 45° lifter face angle. These findings can be useful in guiding actual ball milling tests involving an ore sample.RÉSUMÉ La modélisation par méthode des éléments distincts (MED) est un outil puissant qui permet d’étudier les systèmes particulaires au sein de l’industrie de traitement des minerais. Des simulations par MED ont été menées de façon à étudier le profil de la consommation énergétique, du comportement de la charge et de l’énergie de rupture d’un broyeur à boulets expérimental dans diverses conditions de broyage. Parmi les variables prises en compte figuraient la vitesse de rotation du broyeur (vitesse critique en pourcentage), la taille des boulets et l’angle de coupe de la cornière élévatrice. D’après les résultats de la simulation, on pourrait améliorer l’efficacité de broyage en utilisant une vitesse critique de 80 %, un diamètre de boulet de 30 mm et un angle de coupe de 45 ° de la cornière élévatrice. Ces résultats peuvent se révéler utiles pour les essais concrets de broyage à boulets impliquant un échantillon de minerai.INTRODUCTIONComminution is a very energy intensive process. It consumes approximately 5% of the electricity produced worldwide and more than 50% of the total energy used in mineral processing plants (Pokrajcic, 2010). Among all the comminution stages, ball milling is one of the most energy intensive processes. In ball mills, rotational movement provides the rise of the load and the media that are projected and impact on the mill shell at lower angular displacement, resulting in particle breakage. Ball mills are able to reduce particle size over a relatively wide range of particle sizes. This explains their wide applicability in research laboratories and the mineral processing industry."

Jan 1, 2017

By D. Letzig

Wrought magnesium alloys are of special interest as lightweight structural components as a result of their more homogeneous microstructures and improved mechanical properties compared to cast components. Extrusion as a shaping technology offers the possibility to produce a wide variety of magnesium alloy profiles. In this contribution we describe the role of extrusion parameters such as extrusion speed, ratio and temperature as well as the type of extrusion process on the microstructural development of AZ-series magnesium alloys and the resulting mechanical properties. The effect of microstructure on the tensile/compression deformation behavior of the alloys has also been investigated. Aspects of process optimization designed to overcome technical and economic limitations and thus establish magnesium alloy profiles for industrial applications will also be discussed.

Jan 1, 2006

"Developing markets for western metallurgical coal have continued to stimulate considerable exploration activity in the Rocky Mountain foothills and to influence major segments of a wide-ranging carbonization R&D pro-gram. Adjunct studies have included expanded petrographie investigations.Coal preparation has• been principally directed toward utilization of prepared small coal and was, like much of the year's combustion work, strongly influenced by concern over atmospheric pollution. Particular attention has been given to desulphurization and to the suppression of pollutants in combustion systems.In the area of non-fuel utilization of coal, interest has centered on plant nutrients and on a series of coal-based carbons which, inter alia, possess utility as filtration media.Other projects included the development of improved sampling and analytical methods, investigations into the effect of storage on coal proper-ties and R&D in solids pipelining. In addition, a significant volume of basic 'uncommitted' research has been maintained."

Jan 1, 1968

By Chris Carr

This paper describes the process employed and the work undertaken to enable the surrender of the mine permit relating to the two tailings deposits at the abandoned Red Mountain Mine site near Rossland, BC. The first phase of the work undertaken was to provide urgent remedial work for protection of the environment, primarily through rehabilitation or replacement of surface water drainage systems. The second phase was to up-grade the water management systems to the appropriate level given their consequences of failure. The final phase of work is to ensure long term geotechnical stability of the facilities to the same level of risk. Establishment of a sustaining fund will facilitate long term monitoring and maintenance of the facilities.

May 1, 2002

By Y. F. Jiang, K. Fang, Q. Q. Jiang, Q. Wu

Inter formational sliding of bedding planes between two different rock types in Badong formation is an important reason that leads to the instability and fracture of rock mass in this stratum. There are no specific research achievements on bedding planes between two different rock types in Badong formation. In order to study the shear mechanical properties of bedding planes between two different rock types. This paper using the software of particle flow code (PFC) and JRC model to establish several typical structures of different roughness coefficient of surface morphology based on the laboratory tests on silty mudstone and marlite in Badong formation. A great deal of numerical shear tests were carried out by ball production, radius expansion and servo infliction. The research results are as follows: First, shear strength of Badong formation is found to vary between that of silty mudstone and marlite isotropic planes by analyzing shear strength of the homogenous bedding planes and inhomogeneous rock types, we can find that the shearing strength in Badong formation is between silty mudstone and marlite isotropic planes and which is closer to the shearing strength of silty mudstone isotropic planes. Second, the basical friction angle of bedding planes between two different rock types in Badong formation is between silty mudstone and marlite isotropic planes and which is closer to the basical friction angle of silty mudstone between isotropic planes. Third, based on the experimental results, an expression is obtained to describe the relationship of the ratio of shearing strength between bedding planes of two different rock types and isotropic planes in soft rock, the rock combination coefficient, and the roughness coefficient. This study has important significance for further research on the shear mechanical properties of bedding planes between two different rock types.

Jan 1, 2015

By Rene Cane, V. I. Lakshmanan, John Starkey, Richard May

"The Agrium Kapuskasing Phosphate Operation mines and processes up to 6,000 t/d of phosphate ore. Run-of-mine crushing to minus 6 inches is done in a toothed roll-crusher, while grinding is done in a SAG/ball mill circuit with no coarse recycle classification of the SAG mill discharge. The primary grinding mill is an 18 ft. diameter x 9 ft. EGL, 1500 HP variable speed SAG mill and the secondary mill is a 13 ft. diameter x 21 ft. long, 2000 HP fixed speed, ball mill. When hard ore was treated, the SAG mill restricted the tonnage that could be ground. When soft ore was treated, the ball mill and spiral classifier overloaded and restricted throughput.Recommendations from a plant benchmark and an ore hardness testing program, on how to better utilize installed energy in the Agrium SAG mill when treating soft ore, and how to obtain best results when treating hard ore, were checked in a pilot plant investigation in the 3 ft. diameter Starkey-PRO Pilot SAG Mill. Correlation between the ore hardness testing and the results from the 3’ Pilot SAG mill was very good. In addition, the work indicated the results that could be expected for the different ore types when using either smaller SAG discharge grates and/or a vibrating screen with 10 mesh square opening cloth.INTRODUCTIONAgrium Kapuskasing Phosphate Operation consists of a 6800 t/d open pit mine and a concentrator, near the Town of Kapuskasing in Northern Ontario. The two major ore types are sandy ore and cemented ore. Sandy ore is fine, soft and easy to grind in the SAG mill while cemented ore is harder, more blocky and difficult to grind in the SAG mill. The ratio of sandy to cemented ore in the deposit is thought to be in the order of 80:20 but can range as high as 5050, so it was important for the grinding circuit to have the ability to treat sandy ore alone."

Jan 1, 2002

By L. Henry Smith, David C. Arthur

"The Williams Mine is Canada’s largest gold producer, with annual production of 450 000ounces from 2 300 000 tonnes of ore. Highly mechanized and automated underground mining practices are employed in order to achieve and maintain high levels of productivity and minimize costs.The mine ventilation system is modified to include a new vent raise and variable pitchvane-axial fan. This addition allows several fan installations underground to be decommissioned. A substantial net savings in installed horse power is achieved.Heating costs associated with under-ground ventilation air are a significant portion of mine operating costs. Air heating costs are substantially reduced by recovering heat from upcast exhaust air, minewater and compressor cooling circuits. This waste heat is used to supplement propane fired air heating systems for underground ventilation air. An additional benefit is the availability of a heat sink for summer cooling of the compressors.System design, energy savings data and payback calculations are presented."

Jan 1, 1996

By Alim Ullah

Danieli entered into the Direct Reduction (DR) field in order to offer its clients complete turnkey facilities for steelmaking?from processing of raw materials through finished products. The Danarex® Process produces a passivated product, called the Supermetallic (SPM), without hot-briquetting. One of the main features of the Danarex® Process is its ability to produce approximately 50% of the Direct Reduced Iron (DRI) through reduction gas generated in a reformer and another 50% through recycling preheated furnace exit gas. Some other distinguishing features are: separation of carburising and cooling zones and the use of double bustle for better distribution of gas inside the shaft furnace. A pilot plant was set up at Hazen Research, Inc., Golden, CO in order to show that the integrated process works as expected and to obtain process data. The SPM obtained was of a very high quality, evidenced by metallization levels of 92% to 98%. The carbon content could be controlled between 1.5% to 4.0% by varying the operating conditions and approximately 75% of this carbon was present as Fe3C. The product was tested for inertness by Chilworth Technology, England, using UN standard tests and was found to be safe for outdoor storage and transportation.

May 1, 2003

By Richard R. Walker, John J. Watkins, Allen C. Amos, Matulich. Angelo

THE KIDD CREEK MINE is located within the Abitibi greenstone belt, near its west end, in an area known as the Porcupine mining camp (Fig. 5). The Abitibi belt, long known for its many major gold and base metal deposits, is the largest Archean (early Precambrian) greenstone belt within the Canadian Shield. In the Porcupine area, the greenstone belt is composed principally of Keewatin (older Archean) basic to intermediate volcanics, with subordinate felsic volcanics developed• locally. Greywacke, mainly of volcanic derivation, occurs associated with and overlying these volcanics. Timiskaming (younger Archean) sediments, principally coarse clastics, unconformably overlie the Keewatin volcanics and sediments. The reader is referred to Goodwin and Ridler (1970) •r. for a more comprehensive description of the Abitibi belt.

Jan 1, 1974

By M. M. Williams

WESTERN CAN ADA'S coal industry has experienced a serious set-back since 1949, following a pattern well known to its counterpart in the United States. The loss in coal markets in Western Canada has been particularly severe as the discovery of large reserves of oil and natural gas and the subsequent construction of re-fineries and pipelines roughly coincided with the dieselization of both main railways. While the coal industry will have to face a further decline in markets of long standing, others with a large growth potential can be se-cured if present marketing methods are changed where needed and if fundamental and applied research programmes are actively pursued. The energy and chemical potential of Western Canada's coals will eventually find their place in the ever-growing needs of industry and electric power producers. Electric power generation would appear to offer the largest and most immediate market for coal. If the coal industry is to serve this market adequately and gain as much of it as possible, coal operators ? must have a good knowledge of certain characteristics -of the electric utility industry and its fuel requirements. This paper is prepared primarily to set out some of these characteristics, but also discusses other probable markets for coal.

Jan 1, 1958

By M. Girard, E. Bourricaudy, M. Ashbury, M. Canizares, A. Mezei

Liquid-solid separation and slurry handleability relate directly to commercial plant ramp-up success or lack thereof. The paper provides a well-proven approach for testing, scale-up and commercial application of difficult processes. Emphasis is placed on practical applications of rheological concepts developed both academically and empirically. The cause-effect relationship between the process chemistry and possible physical implications on the metallurgical plant operability is presented in a simple, direct form. Examples include recent results in areas of mineral processing and extractive metallurgy. Technical process risk factors and their mitigation are included in the discussion.

Jan 1, 2011

By M. K. Gangal, M. A. Stoakes, A. E. Hall

"The major features of the CANMET thermodynamic mine ventilation network program, developed by the Mining and Mineral Process Engineering Department of the University of British Columbia for the Canada Centre for Mineral and Energy Technology (CANMET), are described.The program is designed for use by deep Canadian mines in planning ventilation flows where the effects of auto-compression of air, moisture lift work and natural ventilation are significant. Routines to simulate stalled fans and give an optional cost printout have been included in the program.A supplementary plotting program used to simplify data interpretation is also described.The program is described with a test data example of a deep mine. It is a valuable analytical tool which can assist ventilation engineers to simulate many alternative ventilation strategies at a low cost in a very short time.IntroductionCanadian underground mines are becoming deeper and more extensive. The use of more and larger diesel-powered equipment increases the amount of air required to be circulated in these complex systems. These effects, coupled with the increasing unit cost of the energy required for mine ventilation, require that the air is used with maximum efficiency.Optimum airflow distribution can be obtained by using network computer programs enabling engineers to plan future ventilation systems based on quantitative assessments. The programs used for deep mines must make allowance for the change of air density with depth, as the assumption of incompressible flow leads to serious errors. Natural ventilation effects may vary with depth and from part to part of the mine; this must be catered for by the program. The air moisture content changes throughout the circuit and a significant portion of the fan work may be used in removing moisture from the mine; as this work varies directly with the flow, a suitable relationship must be utilized in the program."

Jan 1, 1982

At the end of a century of mining education in South Africa, it is appropriate to reflect on the past, take stock of the present and ponder the future of mining education. While it is likely that changes in the mining industry will generate an increased demand for mining graduates, the number of suitably qualified applicants to study mining is worryingly small. While good progress has been made in unifying the educational system that previously provided schooling on a racially separate basis, it appears that a decade or more will be required to raise competency levels in mathematics, science and English, and this paper describes the process as it affects mining engineering programs. It also describes the initiatives currently being undertaken by the University of the Witwatersrand and the mining industry to ensure that the South African industry receives an adequate flow of well-qualified mining graduates, despite more than 70% of the intake coming from severely disadvantaged educational backgrounds.

Jan 1, 1999

By M. H. Ali

Codelco, a multi-process primary copper producer, is undertaking a full life cycle inventory (LCI) of all its commercial products based on copper and molybdenum. During this work, many questions have surfaced regarding the contribution of process unit design to specific aspects of a product's LCI and, more importantly, how such designs could be improved using a life cycle perspective. Management strategy efforts were undertaken to improve the LCI footprint, however it was found that the corrective actions were almost impossible to apply at the operation level in plant, given the ongoing timing pressures of extractive mining, and costs saving priorities. Additionally, it was found that most of the important comparative differences between operations had structural reasons. In this circumstance, the LCI practitioner group from 1M2, and the environmental managers from Codelco, decided to shift its efforts to place the critical LC1 aspects to the design process of future developments. Hatch Associates has developed unique tools in their Sustainable Plant Design (SPD) package that compliment and enhance LCA methods; these effectively drive sustainability into the heart of the design process. By using LCA and SPD in a project design phase, you cannot only address potential hotspots, but also decide on materials, location and size of certain facilities to optimize for energy efficiency. Moreover, you can avoid the shifting of environmental burdens upstream or downstream within the plant and finally it is extremely useful in identifying opportunities for greenhouse gas reduction.

Jan 1, 2007

By W. B. Boggs

This is a rather comprehensive subject and cannot be thoroughly covered in the short rime allowed for its presentation. This article will touch only upon a few of the chief points of the difficulties encountered in recovering copper from brass shell cases in a primary smelter which was not designed to treat scrap metals. Owing to the fact that the plant is at present (Dec., 1946) closed, and our tests were not completed, full details of the results are not available. As is well known, most primary smelters are situated near the mines in the interior of various countries and are not close to seaports or large industrial and railway centres. Consequently, iris unusual for a primary smelter to be asked to treat scrap metal of any kind. When so required, iris obvious that the primary smelter is at a great disadvantage, for the simple reason that it probably has to pay the freight on the scrap from the seaport or industrial centre to the smelter and then also pay the freight on the recoverable metal from the smelter to the refinery, or seaport or industrial centre. Another disadvantage is that a primary smelter is not equipped to sample and unload the scrap nor bas it usually the equipment adaptable for treating the scrap efficiently, as the plant bas been designed to handle large tonnages of ores and concentrates. This short paper will describe some of our difficulties> and how they were corrected. However, it might be advisable to state briefly some of the methods used in treating brass shell cases in other plants. In the first place, a brass plant producing new brass- especially those producing brass billets for extrusion to make brass tubes or rods, or to be drawn into wire, or making brass cake to roll into brass sheets- generally insists upon using new electrolytic copper and zinc and is opposed to using any scrap or secondary brass . Consequently, such a plant usually will not treat brass shell cases. Therefore, the usual procedure is to ship brass shell cases to a secondary smelter, where it is generally sorted, melted, fire-refined, and returned to the market in the form of a high or low brass ingot which can be sold to brass foundries for making brass castings. This evidently is the cheapest and simplest method. Another method is to ship to a smelter which is a combination of a primary and secondary smelter attached to or near an electrolytic refinery. In plants of both these types, that is a primary smelter with Cottrell dust collectors or a combined primary and secondary smelter with Cottrells or a bag house, the zinc may be wasted. However, if a bag house is used, some of the zinc is recovered, but it is usually contaminated with other metals and further processing is required to recover it.

Jan 1, 1947

By Andrew Barnes

The adsorption capacity of peat collected from a proposed mine development in northern Sweden has been determined using laboratory column experiments in which peat was irrigated with a simulated (acidic) waste rock dump leachate. The simulated leachate was made using a hydrogen peroxide leach of composite waste rock from the proposed mine development. The waste rock samples were composited in proportion to their predicted extractable tonnage for the mine development in order to generate a more representative leachate solution for the waste rock facility. As expected the test revealed that the peat material shows a very high affinity for attenuation with greater than 70% of Co, 90% of Ni and 95% of Cu removed from influent solutions through the majority of the tests demonstrating the potential benefits in mine water treatment. In contrast, it was found that Fe is initially released from the peat at concentrations up to 100 mg/L and can mean potential problems for the water released depending on the receiving environment. The exact mechanisms for Fe release is uncertain, though it is suspected that ion exchange / competitive desorption is responsible. Inspection of the laboratory results and drainage data from the natural peat wetland receiving drainage during overburden prestriping and mine development at the mine site are comparable, confirm the validity of the experiments, and further emphasize the potential for future use of pre-stripped peat material in managing water quality.

Aug 1, 2013

By C. M. Anson

Introduction The prosperity of any country today is dependent upon the efficiency and growth of its primary steel industry. The ?march of the United States of America to its present commanding position in world affairs parallels the growth of its steel industry. The remarkable growth of that industry was possible only because bountiful providence endowed that country with adequate supplies of the raw materials necessary for steel making -coal and iron ore. If we accept this hypothesis, and surely we must, then to what extent can we envisage the future of our own country? This symposium deals with the most important of the raw materials required for steel making -iron ore. If we are blessed with a bountiful supply of iron ore, then surely a glorious future awaits only our taking advantage of that blessing. It is becoming increasingly evident that Canada has immense iron ore deposits. It is my privilege to make you acquainted with one of these, one that can only be classified as among the more important ore reserves in the world. I refer to the Wabana ore deposits in Newfoundland. Location These deposits lie under the floor? of Conception bay, off the east coast of Newfoundland. They consist of a series of beds which outcropped for a distance of about three miles on the northeastern shore of Bell Island, dipping at approximately 8° toward the northwest. This three-mile outcrop is the only key to the occurrence.

Jan 1, 1951